Nano Energy
·
2020
·
IF 16.602
Hongtao Zhao,Run Hu,Pan Li,Anzhu Gao,Xuantong Sun,Xiaohui Zhang,Xiangjun Qi,Qiang Fan,Yida Liu,Xuqing Liu,Mingwei Tian,Guangming Tao,Lijun Qu
Soft actuators with accurate and real-time motion perception are of great importance for flexible machines and artificial intelligence robotics to enable an autonomic response to surroundings. To enhance the sensing-signal reliability and calibration, synchronous motion perception with multiplex feedback signals is desired but has not been sufficiently explored. Herein, we present a soft bimorph actuator that has electrical and visual dual channel signal feedback functions for real-time multiplex motion perception. Cellulose paper and polyimide tape were assembled together as bimorph actuation layers on which an MXene/graphene bilayer was coated for electrothermal function and electrical signal feedback and a thermochromic interlayer was used for real-time visual signal feedback. Based on the proposed actuators, three kinds of bionic robotics and an electro-puppetry robot, “ Wu Song Fights the Tiger ”, with motion-programmable features are demonstrated, revealing the broad application prospects of the present soft actuators in bionic soft robotics with real-time multiplexing motion perception.
研究领域:
生物医学工程
·
智能材料
·
柔性电子
·
仿生学
·
软体机器人
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2021
·Vol. 32
·期 11
·14274-14285
·
IF 2.478
Gao Qianqian,Dai Yuqiang,Wei Xile,Zhou Changping,Gong Wenfeng,Song Haixiang,Guo Zhanhu,Li Chengbo
The Aurivillius compound Pb x Bi 6− x Fe 0.5 Co 0.5 Ti 4 O 18 thin films were prepared via chemical solution deposition method and the influence of Pb 2+ ions doping on the structure, ferroelectric and leakage properties were studied. With the increasing concentration of Pb 2+ ions, the lattice distortion is increased and the growth of the films along ab plane is promoted. The calculation results show that the internal stress of the films increases with the increase of Pb 2+ concentration. For the samples with low Pb 2+ doping concentration ( x < 0.6), the leakage current densities are also decreased, which can be attributed to the decrease in oxygen vacancy concentration. Due to the enhanced lattice distortion and decreased leakage current densities, the ferroelectric properties are improved. The film with x = 0.2 has a high saturation polarization of 42.3 µC/cm 2 . According to the fitting results, the leakage conduction mechanism is attributed to the combined effect of space-charge-limited conduction mechanism and ionic conduction mechanisms.
研究领域:
材料科学
·
凝聚态物理
·
功能材料
·
铁电学
·
薄膜制备
✓ 已验证
DOI
高影响因子
International Journal of Electrochemical Science
·
2023
·Vol. 11
·期 12
·9868-9880
·
IF 1.5
Hongying Li,Xueliang Wang,Tao Wang,Zhaoxia Wang,Wei Zhao
A modified electrode was fabricated by casting graphene oxide (GO) suspension onto the surface of active glassy carbon electrode (GCE), and it can significantly enhanced the oxidation peak currents of m-trihydroxybenzene (m-THB) and p-nitrophenol (p-NP). Based on this, a sensitive analytical method towards their simultaneous determination was established. Many influencing factors such as the type of electrolyte, acidity, scan rates and concentrations were explored. Under the optimal experimental conditions, the oxidation peak currents of m-THB and p-NP were linearly increased with their concentrations ranging from 9 to 100 μM, with the detection limits both of 1 μM. Comparing with other reported methods, this sensor showed wider linear range and lower detection limit. In addition, the proposed method was successfully used to analysis of real environmental water samples with satisfactory recoveries, which verified the practicability of the sensor.
研究领域:
分析化学
·
环境科学
·
电化学
·
传感器技术
·
污染物检测
✓ 已验证
DOI
高影响因子
MICROCHIMICA ACTA
·
2010
·Vol. 171
·期 3
·385-392
·
IF 2.648
Yin Huanshun,Zhou Yunlei,Liu Tao,Cui Lin,Ai Shiyun,Qiu Yanyan,Zhu Lusheng
An amperometric biosensor for nitrite was prepared by immobilizing cytochrome c (Cyt c) on a gold electrode that was modified with Nafion and a Cu-Mg-Al layered double hydroxide (Cu-LDH). The Cu-LDH was characterized by Fourier transform infrared spectroscopy and powder X-ray diffraction. The UV-visible spectrum suggests that Cyt c retains its native conformation in the modified film. The direct electrochemical investigation indicated that the composite film represents a good platform for the immobilization of Cyt c as well as an excellent promoter for the electron transfer between Cyt c and the gold electrode. Moreover, the biosensor showed a remarkable bioelectrocatalytic activity for the oxidation of nitrite with a linear range from 0.75 to 123 μM. The detection limit is 2 × 10 −7 M (S/ N = 3). The biosensor was successfully applied to the determination of nitrite in food samples.
研究领域:
生物分析化学
·
电化学传感
·
食品分析
·
生物传感器
·
分子诊断
✓ 已验证
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2019
·
IF 5.383
Bin Xiao,Wen-hai Zhang,Peng-bo Wang,Lin-bo Tang,Chang-sheng An,Zhen-jiang He,Hui Tong,Jun-chao Zheng,Bo Wang
Phosphate-based polyanion-structured materials have attracted considerable attention as anode materials in lithium-/sodium-ion batteries due to their stable crystal structure, affordability, and environmental friendliness. V 2 (PO 4 )O was encapsulated into crumpled nitrogen-doped graphene (VPO@N-G) through a facile spray-drying method in which VPO particles were completely encapsulated by N-doped graphene. For the first time, VPO@N-G was explored as an anode material for sodium-ion batteries. The Na + storage behavior of VPO@N-G was systematically investigated at the voltage range of 0.01–3.0 V (versus Na/Na + ). Results indicated that the VPO@N-G anode can deliver a highly reversible discharge capacity of 539 mAh g −1 at 0.05 A g −1 and achieve a highly reversible discharge capacity of 235.9 mAh g −1 even at a high current density of 10 A g −1 . Thus, VPO@N-G can be applied as a high-rate anode material for sodium-ion batteries.
研究领域:
材料科学
·
电化学
·
能源存储
·
纳米复合材料
·
无机功能材料
✓ 已验证
DOI
高影响因子
Nano Energy
·
2017
·
IF 12.343
Haoxiang Yu,Hua Lan,Lei Yan,Shangshu Qian,Xing Cheng,Haojie Zhu,Nengbing Long,Miao Shui,Jie Shu
Hollow microstructure always exhibits some special properties in the field of electrochemistry . Here, this study reports the rational design and preparation of TiNb 2 O 7 nanofibers with one dimensional hollow structure via co-electrospinning. The as-electrospun TiNb 2 O 7 hollow nanofibers show high intercalation potential, low charge-charge resistance and fast electrochemical kinetics . The electrochemical results exhibit that the TiNb 2 O 7 hollow nanofibers deliver a reversible capacity of 210.1 mAh g −1 after 150 cycles at a current rate of 0.4 C, and 158.4 mAh g −1 after 900 cycles even at a current rate of 10 C with an outstanding capacity retention of 80.6%. The excellent electrochemical performance of nanofibers can be related to the unique morphology of hollow structure. Furthermore, the lithium ions storage mechanism of TiNb 2 O 7 hollow nanofibers is also systematically analyzed, which is related to one two-phase coexistence and two solid-solution processes during the whole charge-discharge cycle. In addition, it is also demonstrated by in situ and ex situ observations that TiNb 2 O 7 hollow nanofibers have outstanding structural stability and electrochemical reversibility. Therefore, the TiNb 2 O 7 hollow nanofibers can be applied as an alternative promising electrode material for the next rechargeable lithium ions batteries .
研究领域:
材料科学
·
电化学
·
纳米科技
·
能源存储
·
无机功能材料
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2024
·Vol. 50
·期 22
·44983-44992
·
IF 5.1
Shuai Zhao,Hai-lin Ren,Yang Su,Cheng-wei Li,Xiao-min Wang
High-nickel layered cathode materials for lithium-ion batteries have received widespread attention in new energy vehicles for their excellent specific energy and cost advantages, and are considered to be the most promising cathode materials for high-energy density lithium-ion batteries. Despite its many advantages, poor thermal stability and rapid capacity degradation have greatly limited its large-scale application. Ion doping is considered to be an effective way to improve its drawbacks, and in this paper, a series of W-doped LiNi 0.9 Co 0.1 O 2 cathode materials were prepared using WO 3 as a tungsten source. Among them, 1 mol% W doping was the most effective, and its reversible capacity of 204.44 mA g −1 still had 93.25 % capacity retention after 100 this cycles at 1C. Combined with DFT calculations , it is found that the introduction of W does not change the original layered structure and the material transitions from semi-metallic to metallic at lower doping concentrations, resulting in more electrons occupying the Fermi energy levels to enhance its electrical conductivity and leading to an elevated spin state and a lower oxidation state of Ni.
研究领域:
材料科学
·
电化学
·
能源存储
·
固态化学
·
计算材料学
✓ 已验证
DOI
高影响因子
FUEL
·
2023
·
IF 7.4
Muhammad Yousaf,Yuzheng Lu,Majid Niaz Akhtar,Ali Sarosh Khawaja,Khalid Mujasam Batoo,Sajjad Hussain,Asma Noor,Muhammad Akbar,Hu Enyi,M.A.K Yousaf Shah,Naveed Mushtaq,Bin Zhu
Lattice defects in rare earth (RE) doped single-phase semiconductor materials play a key role in structural modifications and physicochemical characteristics, resulting to enhance the ionic conductivity. In this work, we synthesized lanthanum doped samarium oxide with different mole ratios and applied it as a ceramics membrane fuel cell device to enable high peak power density (PPD) at low operational temperatures (520–400 °C). The samples are capable of triple charge H + /O 2− /e − conduction and enhance the catalytic function of the cell in terms of HOR and ORR kinetics by producing lattice defects. The fabricated Sm 1.5 La 1.5 Fe 5 O 12 (2-SLFO) fuel cell device exhibits a high OCV of 1.13 V with a maximum PPD of 864.26 mW/cm 2 at 520 °C. Durability measurement verifies that 2-SLFO-based fuel cell device can be worked for 60 h under fuel cell conditions (H 2 /air) at 520 °C. The first principle calculations using density functional theory (DFT) demonstrate that the higher oxygen vacancy concentration in the 2-SLFO sample may cause to the higher charge-transfer kinetics, subsequent in the enhancement of ions transportation of the fabricated fuel cell device.
研究领域:
材料科学
·
电化学
·
能源材料
·
固态离子学
·
燃料电池技术
✓ 已验证
DOI
高影响因子
Energy Technology
·
2021
·Vol. 9
·期 12
·2100743
·
IF 3.631
Xin Hou,Penggang Ren,Zhong Dai,Zhengzheng Guo,Zengping Zhang,Aiyue Sun,Wenwei He,Fang Ren,Yanling Jin
Herein, nitrogen, oxygen codoped porous carbon nanofibers (CNFs) from corn residue-derived lignin are fabricated via the electrospinning method, followed by introduction of graphenes (GNs) via a simple “brush-coating and drying” process. The obtained GN-coated carbon nanofibers (CNFs@GNs) exhibit a 3D network architecture, abundance of heteroatoms, excellent electrical conductivity, high specific surface area (700.92 m 2 g −1 ), thus boosting the electrochemical performances. The CNFs@GNs electrode delivers a higher specific capacitance of 271.1 F g −1 than CNFs (200.3 F g −1 ) at 1 A g −1 . Furthermore, the assembled CNFs@GNs symmetric supercapacitor exhibits an energy density of 20.3 Wh kg −1 at the power density of 199.97 W kg −1 together with a high charge/discharge reversibility of 97.3% and Coulombic efficiency of 99.81% after 10 000 cycles. This “brush-coating and drying” strategy utilized here provides a convenient and efficient route for designing CNFs and GN composites and can be utilized in other active materials.
研究领域:
材料科学
·
纳米科技
·
电化学
·
能源存储
·
功能材料
✓ 已验证
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2018
·
IF 6.945
Jing Gao,Chunshui Sun,Lei Xu,Jian Chen,Chong Wang,Decai Guo,Hao Chen
Due to flexible property and light weight, the lithiated Nafion membrane swollen with PC (PC-Li-Nafion) has been employed as both solid-state electrolyte and separator to fabricate solid-state Li-S cells. The electrochemical measurements of PC-Li-Nafion membrane show that its Li-ion transference number is 0.928, ionic conductivity of 2.1 × 10 −4 S cm −1 can be achieved at 70 °C and its electrochemical window is 0 ∼ +4.1 V vs. Li + /Li. It is observed that the Li dendrites are suppressed by using PC-Li-Nafion membrane due to its single-ion conducting property. The amounts of Li-Nafion resin binder and conductive carbon in the cathode are optimized as 40% and 10% respectively to make a balance of ionic and electronic conductivities . A thin-layer Li-Nafion resin with a thickness of around 2 μm is fabricated between the cathode and PC-Li-Nafion membrane to improve the interfacial contact and further enhance the specific capacity of the cell. When measured at 70 °C, the Li-S cell delivers a reversible specific capacity of 1072.8 mAh g −1 (S) at 0.05 C and 895 mAh g −1 (S) at 1 C. The capacity retention at 1 C is 89% after 100 cycles. These results suggest that high-performance solid-state Li-S cells can be fabricated with the Li-Nafion polymer electrolyte .
研究领域:
电化学
·
能源材料
·
固态电池
·
聚合物电解质
·
锂离子电池
·
电极界面工程
·
储能技术
✓ 已验证
DOI
高影响因子
Small
·
2019
·Vol. 15
·期 50
·1904854
·
IF 10.856
Junchao Zheng,Zhuo Yang,Alvin Dai,Linbo Tang,Hanxin Wei,Yunjiao Li,Zhenjiang He,Jun Lu
Although the high energy density and environmental benignancy of LiNi 0.8 Co 0.15 Al 0.05 O 2 (NCA) holds promise for use as cathode material in Li-ion batteries, present low rate capabilities, and fast capacity fade limit its broad commercial applications. Here, it is reported that surface modification of NCA cathode ( R-3m ) with 5 nm-thick nanopillar layers and Fm-3m structures significantly improves electrode structure, morphology, and electrochemical performance. The formation of nanopillar layers increases cycling and working voltage stability of NCA by shielding the host material from hydrofluoric acid and improves structural stability with the electrolyte. The modified NCA cathode exhibits an enhanced 89% capacity retention at a rate of 1 C over that of pristine NCA (75.2%) after 150 cycles and effectively suppresses working voltage fade (a drop of 0.025 V after 300 cycles) during repeated charge–discharge cycles. In addition, the diffusion barrier of Li ions in NCA crystals at 0.80 V is noticeably smaller than that of Li ions in pristine NCA (0.87 eV). These findings demonstrate that this unique surface structure design considerably enhances cycle and rate performance of NCA, which has potential applications in other Ni-rich layered cathode materials.
研究领域:
材料科学
·
电化学
·
能源存储
·
锂离子电池
·
纳米材料
✓ 已验证
DOI
高影响因子
RSC Advances
·
2018
·Vol. 8
·期 65
·37417-37423
·
IF 2.936
Jihui Li,Kang Sun,Changyu Leng,Jianchun Jiang
Reasonable structure design and component selection are crucial to electrochemical performance of supercapacitor electrode materials. Sodium alginate (SA), with a novel structure which can immobilize multivalent metal cations, was used to coordinate with Fe3+ to fabricate a carbon and Fe3O4 composite by an easy sol–gel method. Due to the chelation effect between SA and Fe3+, the carbon composite was constructed into a two-dimensional sheet-like structure, and the Fe3O4 particles were nanosize and homogenously distributed on the surface of the carbon nanosheet. As an electrode material for supercapacitors, the composite electrode showed a high specific capacitance of 550 F g−1 at 1 A g−1 in the potential range from −1.1 to 0 V, and excellent cycling stability of 89% retention after 2000 cycles. The enhanced electrochemical performance could be attributed to the abundant exposed active sites, producing high pseudocapacitance, to the two-dimensional nanosheet structure, facilitating electrolyte transport and to the strong attachment strength, improving cycle life. This environmentally-friendly design can provide an alternative to existing methods, resulting in the development of a two-dimensional carbon/metal oxide composite for energy storage devices.
研究领域:
材料科学
·
电化学
·
纳米科技
·
能源存储
·
功能材料
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）