E-POLYMERS
·
2022
·Vol. 22
·期 1
·488-504
·
IF 3.074
Fangsheng Wu,Zihua Zhang,Wei Liu,Yuan Liu,Xiujuan Chen,Pingyong Liao,Qiaoying Han,Lun Song,Hong Chen,Wenbin Liu
In this study, a novel material of core–shell structured magnetic molecularly imprinted polymers (Fe 3 O 4 @SiO 2 @Au (FSA)-MIPs) was successfully prepared for the rapid and selective determination of 4-methylmethcathinone (mephedrone, 4-MMC). The adsorption capacity of FSA-MIPs is 34.7 mg·g −1 at 308 K, which is significantly higher than magnetic non-imprinted polymers profiting from the imprinting effect. The FSA-MIPs have a short equilibrium (20 min) and could be reused more than six times. Moreover, the selectivity coefficients of FSA-MIPs for 4-MMC, 3,4-dimethylmethcathinone, butylone, 4-ethylmethcathinone, acetylfentanyl, and methylene blue are 4.01, 5.65, 7.62, 12.30, and 20.87 respectively, further indicating the markedly enhanced binding selectivity of FSA-MIPs. As an adsorbent, the FSA-MIPs were successfully applied for effective extraction of 4-MMC in three human urine samples with the recovery rates ranging from 85.5–92.6%. The results confirmed that the FSA-MIPs have good prospects in the extraction and separation of synthetic cathinones, which is suitable for further application in the criminal sciences field.
✓ 已验证
DOI
高影响因子
SENSORS AND ACTUATORS B-CHEMICAL
·
2025
·
IF 7.7
Rui Wang,Yimin Tang,Yanan Lu,Zhiyu Wang,Xin Jiang,Bing Zhao,Libin Yang
Constructing a heterogeneous structure with the combined contribution of electromagnetic (EM) and chemical (CM) mechanisms, while enabling all components to contribute to each mechanism, is an effective strategy for developing new high-performance surface-enhanced Raman scattering (SERS) substrate. In this work, a novel 3D/1D MoS 2 flower-like microspheres@Au nanowires (MoS 2 FMs@Au NWs) heterojunction SERS matrix platform is successfully developed through morphology regulating and interface engineering strategies. The enhancement factor of SERS matrix is as high as 3.97 × 10 9 . The theoretical simulations and experiments reveal the combined contribution of EM and CM mechanisms. The dual EM effects (Mie resonance triggered by 3D MoS 2 FMs and hotspot effect of high-density Au NWs customized by highly ordered MoS 2 ) and the multidimensional CM contributions (high-efficiency carrier separation of MoS 2 triggered by heterostructure and high carrier utilization rate from hot electron excitation of Au NWs) can be synchronously achieved for boosting SERS activity of the heterojunction. More meaningfully, the developed SERS matrix can realize an ultra-sensitive detection for trace fungicide residues (crystal violet and malachite green) in real water system. This discovery provides new insights and perspectives for developing novel function-customized SERS substrates, aiming to advance the practical application of SERS technology.
✓ 已验证
产品关联
DOI
高影响因子
FOOD CHEMISTRY
·
2025
·
IF 9.8
Hui Pan,Meng Jin,Fang Zhang,Xuelei Chen,Mengping Zhang,Haiyan Wei,Xiao Meng,Wenwen Chen,Zhihu Zhang,Cuijuan Wang
Health concerns over mixed pesticide residues highlight the need for rapid detection methods. This study developed a multifunctional point-of-use (POU) sensor that integrates separation, enrichment, and surface-enhanced Raman spectroscopy (SERS) using high-index Au trisoctahedrons (TOHs) and metal-organic frameworks (MOFs) on polyamide 6 (PA-6) film. The Au TOHs with sharp tips and high index facets offer excellent SERS performance, while MOFs facilitate analyte enrichment and separation. The flexible PA-6 film was used as an absorbent for the initial adsorption. Using the AuTOHs@ZIF-67/PA-6, we achieved on-site detection of chlorfenapyr (CFP) and emamectin benzoate (EB) in 5 min without pre-treatment, significantly faster than traditional methods. Detection limits were 0.68 ppb for CFP and 0.26 ppb for EB on cucumber surfaces, and 0.13 ppb and 0.95 ppb, respectively, in cucumber juice, well below tolerance levels. This method shows great promise for detecting pesticide mixtures in non-laboratory settings, offering a new POU alternative.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
FOOD CHEMISTRY
·
2025
·
IF 9.8
Jing Feng,Sheng Yao,Xiaohan Mei,Jiacheng Xie,Xujie Wang,Huitian Zhi,Ruhui Shang,Yingchao Yang,Lei Hu,Zhengquan Yan
To conveniently monitor and remove toxic Hg 2+ and S 2− in food samples, Au Ag quantum-dot nanozyme (Au-Ag@FA QDs) was identified. The strong synergistic effect among folic acid (FA), Ag and Au endowed Au-Ag@FA QDs with superior peroxidase-mimic activity to accelerate 3,3′,5,5′-tetramethylbenzidine (TMB) redox with K m / V max of 0.28 mmol·L −1 /6.40 × 10 −8 mol·L −1 ·s −1 . Trace Hg 2+ or S 2− could selectively alter its peroxidase-like activity and inherent fluorescence performance, with obvious hyperchromic/“turn-on” fluorescent effect for Hg 2+ or hypochromic/“turn-off” one for S 2− . And red-green-blue (RGB) values analyzed from smartphones changed regularly with c Hg 2+ or c S 2− . Under the optimized conditions, Au-Ag@FA QDs were successfully applied for multi-mode UV–vis, fluorescent, and RGB monitoring of Hg 2+ or S 2− in food samples. The detection limits were 7.38 × 10 −7 /5.74 × 10 −8 /4.93 × 10 −6 g·L −1 and 1.99 × 10 −6 /4.48 × 10 −8 /5.79 × 10 −6 g·L −1 respectively. Importantly, over 93.8 % Hg 2+ or 90.5 % S 2− could be removed by simple centrifugal-separation after detection. The selective recognition mechanisms to Hg 2+ and S 2− were also proposed.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
APPLIED SURFACE SCIENCE
·
2021
·
IF 6.707
Yue Tian,Qingqiang Cui,Hui Ma,Anxin Jiao,Chang Wang,Mengya Zhang,Linqi Zheng,Xuelin Wang,Shuang Li,Guihua Li,Ming Chen
Based on plasmonic metallic nanomaterials (NMs) with unique local surface plasmon resonance (LSPR), the photo-excited hot carrier-driven hydrogenation reaction becomes a new family of photocatalytic transformations in recent years. However, the high work function and rapid hot-carrier recombination of plasmonic NMs create huge barriers for widespread practical application. Herein, we propose a fascinating reactor of up-regulated electrochemical LSPR (EC-LSPR) driven hydrogenation reaction via the construction of hierarchical Au pine needles (H-Au PNs) with enhanced lightning rod effect under appropriate extra electric field. The plentiful elongated Au branches with sharp corners and edges can be served as excellent electron-transport channels for facilitating photo-excited hot carrier transmission and accelerating hot electron collection at nano-tips after plasmon decay. Additionally, the extra electric field with the applied voltage of − 0.8 V further improves the surface charge density and the internal polarization of H-Au PNs, boosting the separation efficiency of hot carriers as well as reducing the photoelectrochemical (PEC) potential on H-Au PNs. It directly leads to an effective activation enthalpy reduction to reach above the energy threshold of water splitting, which can achieve the direct plasmon-driven PEC-hydrogenation conversion of 4-nitrothiophenol (4-NTP) to 4-aminothiophenol (4-ATP) in aqueous solution, and the conversion rate constant is about 5 times higher than bare EC-driven conversion. The present work provides a new opportunity for the emerging direct plasmon-driven hydrogenation reaction.
✓ 已验证
DOI
高影响因子
ACS Applied Nano Materials
·
2021
·
IF 5.097
Yuan Wang,Lei Feng,Haiyan Zhu,Hongyan Miao,Ying Li,Xuefeng Liu,Gang Shi
The fluorescence intensity of the ring-opened merocyanine (MC) form of spiropyran can be enhanced by metal nanostructures. However, direct contact between spiropyran and the metal results in fluorescence quenching, which will reduce the enhancement amplitude of MC fluorescence. Here, Ag nanoparticles (NPs), a TiO2 dielectric layer, a poly(methyl methacrylate)-spiropyran (PMMA-SP) layer, and Au shell-isolated NPs with SiO2 shells (Au@SiO2) are successively assembled on a Si wafer with micropyramids and nanoholes (Siph). The hierarchical structure of this substrate is similar to insects’ compound eyes with nano- and microstructures, which can reduce the reflection of incident light. Meanwhile, the Au/Ag-coupled plasmonic nanocavities can enhance the intensity of a local electromagnetic (EM) field. In addition, TiO2 and SiO2 layers can avoid the nonradiative energy transfer caused by the direct contact between spiropyan and the metal. Based on the above advantages, the fluorescence enhancement factor (EF) of this substrate is as high as 195, which is the maximum reported so far. Zn2+, Cu2+, and Sn2+ can also be detected on Siph/TiO2/PMMA-SP/Au@SiO2, whose detection limits are 0.054, 0.038, and 0.049 μM, respectively. Furthermore, this substrate can be reused to detect metal ions by taking advantage of the reversible isomerization of spiropyran. The bioinspired substrate has positive significance in improving the fluorescence intensity of MC, and its lack of specific recognition ability for metal ions is expected to be further improved by molecular modification of spiropyran.
✓ 已验证
DOI
高影响因子
MICROCHEMICAL JOURNAL
·
2024
·
IF 4.9
Dalan Jin,Zijing Xu,Hongyi Zhao,Silang Deng,Zhuangzhuang Qu,Runye Dou,Weilu Liu
Glucose monitoring in interstitial skin fluid (ISF) has become a novel approach for diabetes management. In this paper, a minimally invasive sensing system consisted of methacrylated hyaluronic acid (MeHA) based microneedle patches and Au/Cu 2 O nanospheres modified screen-printed carbon electrode (SPCE) was designed for glucose monitoring in the ISF of living mice. The highly swellable and biocompatible MeHA microneedle patches can effectively extract ISF from the skin, barely cause pain to the living mice. The glucose level in the extracted ISF was detected via an enzyme-free electrochemical sensor using the Au/Cu 2 O nanospheres as the electrocatalyst. The doping of Au into Cu 2 O resulted in a highly conductive and active electrocatalyst for glucose oxidation, which improved the sensing performance of glucose sensor. A wide linear range (0.02 – 6 mM), low detection limit (0.018 mM), and high sensitivity (110.38 μA mM −1 cm −2 ) were obtained under the optimized condition. The obtained results exhibited a comparable trend to those obtained from commercial glucometers. We have combined successfully MeHA patches for ISF extraction with enzyme-free electrochemical glucose sensor. Therefore, this novel sensing system holds great potential for diabetes management in a minimally invasive manner.
✓ 已验证
DOI
高影响因子
MICROCHEMICAL JOURNAL
·
2025
·
IF 5.1
Xuemin Qin,Zhi Luo,Shenglan Hu,Xuyang Deng,Jing Li,Lingling Zheng,Biyang Deng
In conventional co-reactant electrochemiluminescence (ECL), the efficiency of converting co- reactant into active intermediates is the primary factor limiting luminescence intensity. To address this limitation, we synthesized carboxyl-functionalized CdIn 2 S 4 (Cf-CdIn 2 S 4 ), which served dual roles as both a luminescent material and a co-reactant accelerator. As an emitter, Cf-CdIn 2 S 4 , generated strong and stable ECL signals upon excitation at −1.3 V. Furthermore, Cf-CdIn 2 S 4 exhibited remarkable electrocatalytic activity for K 2 S 2 O 8 activation. Through the In 3+ /In 2+ valence state transition, Cf-CdIn 2 S 4 significantly facilitated the conversion of S 2 O 8 2− to SO 4 ·− , achieving self-enhanced ECL signals. The pronounced quenching effect of Au@MoS 2 on the Cf-CdIn 2 S 4 ECL signal was exploited to develop a highly sensitive quenching-type ECL sensing platform for H-FABP. The developed immunosensor exhibited a broad linear detection range (10 fg/mL–100 ng/mL) and a low limit of detection (3.2 fg/mL, S/N = 3). This novel approach provides a highly sensitive and reliable platform for the early diagnosis of acute myocardial infarction and can be effectively utilized for the early screening of cardiovascular diseases and clinical monitoring of critically ill patients.
✓ 已验证
产品关联
DOI
高影响因子
Surfaces and Interfaces
·
2025
·
IF 6.3
Junzhe Han,Weiting Liu,Wenwen Zheng,Xueqi Zhang,Guoyuan Zheng,Nan Tian,Jilin Wang,Yang Yang,Fei Long,Disheng Yao
Copper(I) thiocyanate (CuSCN) is a relatively inexpensive and stable p-type hole transport material suitable for fabricating perovskite solar cells (PSCs). However, devices using CuSCN often exhibit poor stability due to severe degradation at the CuSCN/metal-electrode interface, and the root cause remains unclear. In this study, we address this issue by constructing a modified hole transport layer (HTL) through the introduction of an ultra-thin interlayer of cobalt thiocyanate (Co(SCN) 2 ) between CuSCN and the Au electrode. This strategy not only reduces the surface roughness of the CuSCN film surface but also establishes favorable energy level alignment, thereby improving hole extraction efficiency. Additionally, it prevents the degradation of CuSCN caused by the self-disproportionation reaction of Cu + in CuSCN (Cu + = Cu 0 + Cu 2+ ) through the alloying of Cu/Au. Consequently, the PSC fabricated with the CuSCN/Co(SCN) 2 -layer achieves an impressive power conversion efficiency (PCE) of 19.38%, making it one of the highest efficiencies among dopant-free inorganic HTL-based PSCs. Importantly, the device with Co(SCN) 2 demonstrates overall enhancements in operational stability under continuous light illumination, moisture attack and thermal stress. This work finds a dual-interface passivation for making efficient and stable CuSCN-based PSCs with different device structures, which has a certain contribution to the surface & interface engineering of CuSCN-based PSCs.
✓ 已验证
产品关联
DOI
高影响因子
FOOD CHEMISTRY
·
2025
·
IF 9.8
Hongbo Li,Hao Wang,Meiyi Cao,Xing Tong,Shuo Wang,Mingfei Pan
The fluoroquinolone-enrofloxacin (ENR) residue in animal-derived foods poses a significant threat to human health, thereby necessitating developing precise, efficient, and user-friendly detection methods. This study developed a dual-mode fluorescence-colorimetric immunosensing platform using the composite of bimetallic nanoparticles integrated with metal-organic frameworks (Au/Pt NPs@NH 2 -MIL-53(Al)). The Au/Pt NPs with biocompatibility and peroxidase-like activity were modified onto fluorescent NH 2 -MIL-53(Al) and conjugated with Ab 2 to construct signal probes. The platform enables dual-mode quantitative analysis through the competitive binding of ENR and ENR-BSA conjugate to signal probes. It demonstrated a wider linear range (0.08–180 ng/mL) and high sensitivity [LOD: 0.068 ng/mL (fluorescence), 0.066 ng/mL (colorimetric), and 0.074 ng/mL (smartphone-assisted color recognition)]. In real sample analyses, the recoveries ranged from 86.7 % to 106.7 %, with satisfactory stability (RSD ≤ 4.4 %, n = 3). The dual-signal mode facilitates results self-calibration, enhancing reliability, while smartphone-assisted color recognition enables on-site, convenient screening, offering great potential for ENR detection in complex food matrices.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ANALYTICA CHIMICA ACTA
·
2025
·
IF 6
Xiaoshuo Zhang,Rui Dai,Faqiong Zhao,Baizhao Zeng
Background Epithelial cell adhesion molecules (EpCAM) protein is one of the most frequently and intensely studied tumor-associated antigens because of its overexpression in most cancer cells. Thus, it is regarded as a tumor biomarker associated with a wide variety of carcinomas and reflects the existence and growth of tumors in the human body. It is highly required to detect low concentrations of EpCAM in early stage for ensuring human health. Results In this study, a novel sandwich electrochemiluminescence (ECL) aptasensor was developed for EpCAM detection. Wherein oxalate-based Zn-MOF supported tris(2,2′-bipyridyl)ruthenium (II) (Ru(bpy) 3 2+ @Zn-MOF) was used as luminophore and gold nanoparticle modified o-phenylenediamine (PoPD@Au NPs) as quencher. The 3D Ru(bpy) 3 2+ @Zn-MOF generated self-enhanced ECL without additional co-reactants. Furthermore, it remained stable and had short electron transfer distance, ensuring high and stable ECL signal. The ECL signal could be effectively quenched by PoPD@Au NPs through resonance energy transfer (RET) and electron transfer (ET), due to its absorption spectrum overlapping with the ECL emission spectrum of Ru(bpy) 3 2+ @Zn-MOF. In the presence of EpCAM, the aptamer acted as a linker between the luminophore and quencher, forming a sandwich structure that had reduced ECL intensity. Under optimal conditions, EpCAM could be sensitively detected over the range of 1 pg mL -1 -100 ng mL -1 , with a detection limit of 0.34 pg mL -1 . Significance This work developed a ECL aptasensor with self-enhanced Ru(bpy) 3 2+ @Zn-MOF luminophore for EpCAM detection. The ECL system was simple, but ultrasensitive for EpCAM monitoring, thanks to the ECL-RET and ET between Ru(bpy) 3 2+ @Zn-MOF and PoPD@Au NPs. It also could be applied to detect other biomolecules by replacing the aptamer, offering significant potential in disease diagnosis.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
TALANTA
·
2025
·
IF 6.1
Lei Tian,Qi Guo,Luting Yan,Yuhao Zhang,Zekun Ren,Chao Wang,Xia Sun,Yemin Guo,Yanyan Zhang
Heavy metal cadmium (Cd (II)) contamination in aquatic products poses severe health risks, necessitating rapid, accurate, and portable detection methods. Traditional electrochemical sensors often suffer from background interference and low accuracy, especially when utilizing stainless steel acupuncture needles as electrodes. Single-signal systems are prone to environmental fluctuations, limiting reliability. Thus, there is an urgent need for a sensitive, low-cost, and visual sensor that integrates dual detection modes for on-site analysis of Cd (II). We report a novel ratiometric/colorimetric dual-mode aptamer sensor based on a polyaniline-gold nanocomposite (PANI@Au)-modified acupuncture needle. This platform uses PANI's peak at −0.9 V as an internal reference and His-Pd@aptamer's peak at −0.2 V as a detection signal, enabling ratiometric electrochemical quantification. In parallel, His-Pd nanoparticles catalyze the oxidation of TMB to produce a blue color, allowing visual detection with a limit of 3.10 × 10 −2 ng/L. RGB values are analyzed by a smartphone and WeChat mini-program for rapid result output. The electrochemical and colorimetric modes demonstrated excellent sensitivity (LOD: 3.40 × 10 −2 ng/L electrochemical; 1.06 × 10 −1 ng/L RGB-based) and linear range of 10 1 –10 8 ng/L. The sensor showed strong selectivity, stability, and successful application in detecting Cd (II) in fish, shrimp, and scallop samples with high recovery rates. This is the first report of a needle-based ratiometric/colorimetric aptamer sensor that enables both electrochemical quantification and smartphone-based visual detection of Cd (II). The device supports rapid, on-site, and low-skill operation with sub-100 μL samples, demonstrating its potential for real-time monitoring of heavy metal contamination in aquatic food safety.
✓ 已验证
产品关联
DOI
PubMed
高影响因子