LANGMUIR
·
2024
·
IF 3.7
Zhenghao Zhang,Bo Peng,Yupeng Zhang,Jiaxin Xiong,Jingwei Li,Jianwei Liu
A CO2/N2-responsive emulsion provides milder reaction conditions, nontoxicity, and economic feasibility compared to other switchable surfactants. In this study, CO2/N2-responsive pickering emulsions were fabricated by using a compounded dispersion containing SiO2 nanoparticles (NPs) and superamphiphiles as the emulsifying agents. The synergistic effects of the SiO2 NPs and superamphiphiles significantly stabilized the emulsion at all of the tested concentrations and prevented complete phase separation of oil and water. The electrostatic interaction between the SiO2 NPs and superamphiphiles was disrupted after bubbling with CO2 for 30 s, resulting in the breaking of the emulsion. However, the dispersion recovered its interfacial activity after the introduction of N2 and again emulsified the emulsion. This reversible switching behavior was validated through three consecutive cycles of bubbling CO2/N2. The protonation and deprotonation of the SiO2 NPs and superamphiphiles in response to CO2/N2 facilitated reversible assembly and disassembly, which enabled the switching of the emulsions between inactive and active forms. The novel highly stable Pickering emulsions demonstrated rapid demulsification and emulsification in response to CO2/N2 and are promising for a wide range of applications.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
FUEL
·
2025
·
IF 7.5
Zekai Miao,Hao Ge,Xinran Han,Rui Wu,Hai Zhu,Congchao Zhang,Shengping Wang
The coal gasification fine slag (FS) is a solid waste rich in Si components. The preparation of high-performance mesoporous silica for CO 2 capture using FS as raw materials will alleviate environmental pollution. The alkali-fusion method was used to obtain the high activated Si-containing precursor which could be completely dissolved in NaOH solution with low alkalinity concentration (3 %). The mesoporous silica with highly ordered hexagonal phase was prepared which had high surface area of 1629 m 2 /g and pore volume of 0.8 cm 3 /g. The Si concentration had the great effect on the yield of mesoporous silica and the mechanism for the formation and growth of mesoporous silica between high and low Si-precursor concentration was different. In the preparation process for high yield of mesoporous silica, the silicate ions primarily tended to adsorb around the cetyltrimethylammonium bromide micelles to form nuclei and then the silicate reacted preferentially with the surface silanol groups on the existing particles rather than generating new nuclei. The condensation of the silicate at the external surface of the surfactant micelles occurred to grow into large particles. However, the mesoporous silica particles formation in the lower concentration of silicate species in the alkali solutions was mainly contributed to the interactions between silicate species and CTAB rather than the deposition of silica species. The mesoporous silica showed high CO 2 adsorption performance. The breakthrough time of MS-8 occurred at 22 min and CO 2 adsorption capacity was 2.3 mmol/g at 25 °C. All these results suggest that the silica in fine slag could be fully utilized to prepare mesoporous silica which had a great potential to be used for practical and industrial CO 2 adsorption applications.
✓ 已验证
产品关联
DOI
高影响因子
MICROPOROUS AND MESOPOROUS MATERIALS
·
2024
·
IF 4.8
Ying Gao,Jiafeng Zhang,Yanan Tu,Weidong Wang,Ziqi Zhu,Zhiqiang Xu
The preparation of hierarchical porous silica aerogels from coal gasification fine slag (CGFS) offers an effective approach to achieving high-value utilization of solid waste and reducing the production cost of solid adsorbent matrix materials. However, the main challenges involve overcoming technical barriers to efficiently and value-added conversion of CGFS into silica aerogels with CO₂ adsorption properties, as well as elucidating the phase transformation mechanisms during the synthesis process. In this study, CGFS was used as the raw material to obtain a silicon-containing precursor through pre-decarbonization (with ash content as high as 99.82 %) and alkali dissolution treatment. A hierarchical porous silica aerogel was then synthesized using an efficient hydrothermal process. The effect of alkali dissolution on silicon extraction and the phase transformation mechanisms were thoroughly discussed, and the leaching mechanism was analyzed through thermodynamic and kinetic models. The results showed that the high leaching rate of silicon was attributed to the presence of a large amount of amorphous SiO₂ in the decarbonized fine slag (DCFS), while the formation of zeolite Na-P1 and hydroxysodalite during the alkali dissolution process affected the efficiency of silicon extraction. Then, the structural formation mechanism and CO₂ adsorption properties of the hierarchical porous silica aerogels were analyzed using N₂ adsorption-desorption and CO₂-TPD. The SiO₂-1-30-0.5 exhibited a high CO₂ adsorption ability of 1.53 mmol g −1 , and the CO₂ adsorption capacity maintained 94.78 % of the original value and after 5 adsorption-desorption cycles.
✓ 已验证
产品关联
DOI
高影响因子
Science Advances
·
2025
·Vol. 11
·期 32
·
IF 12.5
Congcong Yin,Muning Chen,Ziyin Zhang,Kai Liu,Jinglin Gao,Xin Zhao,Yuping Wu,Yong Wang
Creation of membrane channels capable of recognizing diverse molecules is desirable for advancing molecular transport and separation, but it remains difficult to precisely control their conformation and achieve dynamic adaption to specific molecules. Here, we demonstrate fine-tuning the pore environment within 3D covalent organic framework (COF) that can precisely control its pore size and polarity to recognize CO 2 . The pores are integrated with azobenzene units with photo-adaptable trans-to-cis isomerization, enabling dynamic pore size regulation at angstrom scale. Moreover, the isomerization induces drastic changes in intrapore polarity, which exert profound effects on the intermolecular affinity through the dipole-quadrupole interaction. Featuring these dynamic natures, the 3D COF membrane cooperating the size exclusion effect with a molecular recognition ability toward CO 2 . As a result, light-gating separation experiments show the superior CO 2 capture performance with a N 2 /CO 2 selectivity of 27.6. Theoretical calculations reveal that cis-state azobenzene can reduce the electron transfer barrier from azobenzene to CO 2 , thereby providing a molecular recognition pathway.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Journal of Environmental Chemical Engineering
·
2025
·
IF 7.2
Jing Bai,Chenxu Qiu,Yanhui Wang,Qianqian Zhu,Zheng Yan,Chun Chang,Pan Li,Dongyang Li
Separating CO 2 from flue gas through hydrate method owns many advantages, including easy operation, environmental friendliness, low-energy consumption during the process, and the potential for water recycling in the reaction. This study investigated the effects of cyclopentane (CP, 5.0 vol%), methionine (L-Met, 0.2 wt%), and alkyl polyglucosides (APG) with various carbon chain lengths as additives on the kinetics of flue gas hydrate generation in a simulated power plant environment, with a focus on gas separation efficiency. Key parameters, including impinging strength ( β ), feed pressure, initial temperature, and APG carbon chain length, were systematically investigated to optimize the hydrate formation process. The results reveal that gas consumption ( Δ n H ), average reaction rate ( R H ), and CO 2 capture rate ( S.Fr. (CO 2 )) initially increases with β , reaching a peak before decreasing, while the CO 2 separation factor ( S.F. (CO 2 )) consistently increased. Higher feed pressures and lower initial temperatures enhanced gas consumption, thereby accelerating the hydrate formation and improving separation efficiency. Additionally, the optimal APG carbon chain length significantly enhanced both the kinetics of hydrate formation and gas separation efficiency. Specifically, under conditions of 6 MPa, 275.15 K, and β = 0.13, the CP+L-Met+APG0814 system achieved a maximum Δ n H of 0.509 mol, an R H of 0.102 mol/h, and a S.F. (CO 2 ) of 82.4 %, demonstrating the potential for improved CO 2 capture in hydrate-based separation processes.
✓ 已验证
产品关联
DOI
高影响因子
ACS Sustainable Chemistry & Engineering
·
2025
·
IF 7.3
Kai Zhu,Zihan Lin,Xinyi Bai,Fangfang Chang,Qing Zhang,Xiaolei Wang,Zhengyu Bai
Electrocatalytic reduction reaction of CO2 (CO2RR) into value-added multicarbon (C2+) products represents a sustainable strategy for mitigating greenhouse gas emissions and enhancing the production of high-value chemicals. Cu-based catalysts are optimal for the CO2RR, facilitating the generation of C2+ products such as ethanol, which have significant industrial applications. However, converting CO2 to C2+ products remains a great challenge, necessitating the simultaneous achievement of high current density, Faradaic efficiency (FE), and operational stability for industrial-scale implementation. Herein, we prepared Cu/Cu2O catalysts with diverse morphologies and the ratio of the Cu+/Cu interface, which was rectified by regulating the interactions between the active interface and the intermediate (*CO). The electrochemical analysis demonstrated that reconstructed Cu/Cu2O nanodendrites with dominant grain boundaries exhibited remarkable performance in generating C2+ products, achieving a Faradaic efficiency (FE) of 71.8%, including 49.7% FE of ethanol and a substantial partial current density of 390.0 mA cm–2 within the flow cell. In situ spectroscopy characterization and theoretical calculations revealed that the increased ethanol selectivity originated from the rectification of the Cu/Cu2O interface by the *CO intermediate, which accelerated H2O dissociation, reduced the free energy for *CO hydrogenation to *COH, and facilitated asymmetric *CO-*COH coupling to preferentially reduce CO2 to ethanol. This study provides profound insights into the C–C coupling pathways and sheds light on the rational design of ethanol-oriented electrocatalysts, contributing to sustainable chemical synthesis and energy utilization.
✓ 已验证
产品关联
DOI
高影响因子
Frontiers of Chemical Science and Engineering
·
2025
·Vol. 19
·期 12
·1-11
·
IF 4.5
Pan Chunhong,Wang Biao,Mao Jinman,Li Mengjia,Wang Huimin,Chen Wenyi,Gao Feng,Hu Guoping,Fan Xiaolei,Huang Feng
Reverse water-gas shift reaction represents a strategic pathway for CO 2 utilization. Despite its potential, reverse water-gas shift reaction via conventional thermal-catalysis faces several challenges, including low equilibrium conversion rates due to thermodynamic constraints, high energy consumption, and insufficient product selectivity. Here, this study demonstrates an evident synergetic effect between plasma and Ag/ZnO, on enhancing reverse water-gas shift reaction. The plasma catalytic system achieved significantly improved performance with a remarkable CO 2 conversion rate of 76.5%, a high CO selectivity of 96.8% and a CO yield of 74.1%, along with an energy efficiency as high as 0.19 mmol·kJ −1 , surpassing the plasma alone system and ZnO catalytic systems. Results from X-ray photoelectron spectroscopy and Auger electron spectroscopy confirm the presence of electronic metal-support interactions between Ag and ZnO, which facilitates the formation of electron-deficient Ag sites and partially reduced ZnO x species. These reactive sites, along with oxygen vacancies created during reduction treatment, enhance the adsorption and activation of H 2 and CO 2 , offering a dominant plasma-assisted surface reaction pathway for the improved reverse water-gas shift reaction. These findings underscore the crucial role of electronic metal-support interactions in manipulating surface environments to facilitate efficient plasma-assisted catalytic reactions, with significant implications for the rational design of catalysts capable of converting CO 2 efficiently under mild conditions.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2025
·
IF 9.7
Man Zhao,Wei Wen,Chunmei Liu,Qinyun Yan,Shuai He,He Xiao,Li Zhang,Junming Zhang,Xiaofeng Gao,Jianfeng Jia
The electrochemical CO 2 reduction reaction (CO 2 RR) to multi‑carbon products offers a promising route for sustainable fuel production, yet achieving high selectivity remains challenging due to the complex interplay between catalyst structure and reaction pathways. Here, we report a rational design of Cu-Cu 2 O/graphene (Cu/G) composites with tunable Cu + /Cu 0 ratios via electrolyte-mediated electrochemical synthesis. By varying tetraalkylammonium/phosphonium electrolytes (TBABF 4 , TBAPF 6 , TBACF 3 SO 3 , TBPBF 4 ), we precisely control Cu oxidation states, as validated by the results of X-ray absorption fine structure (XAFS), X-ray diffraction (XRD), and high-resolution transmission electron microscope (HRTEM). In-situ Fourier transform infrared (In-situ FTIR) spectra and in-situ Raman spectra indicate Cu + -rich surfaces (Cu/G-TBABF 4 ) favor the production of formate via O-bound intermediates, while Cu 0 -dominated interfaces (Cu/G-TBAPF 6 ) promote the formation of CO through C-bound pathways. Mixed Cu + /Cu 0 systems (Cu/G-TBACF 3 SO 3 , Cu/G-TBPBF 4 ) enable C C coupling, with ethylene (FE = 28 %) and ethanol (FE = 30.2 %) selectivity governed by the Cu + /Cu 0 balance. Ultraviolet photoelectron spectroscopy (UPS) results reveal that lower work functions enhance *CO coverage and stabilize C 2+ intermediates, elucidating the electronic structure-activity relationship. This work demonstrates electrolyte-mediated oxidation state engineering as a versatile strategy to steer CO 2 RR pathways, offering a generalizable approach for designing multi-valent electrocatalysts with tailored selectivity.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2025
·
IF 9
Xiaole Dong,Shihui Wang,Bingqi Tan,Xiangyi Geng,Futang Liu,Penghao Gao,Peiling Gao,Jiutao An,Xinpeng Liu,Qingmei Meng
Different nanoparticles were introduced into the N-ethylethanolamine/diethylaminoethanol/p-Xylene biphasic absorbent to form nanofluid systems, and the CO 2 capture performance was investigated. The CO 2 capture performance of the absorbent was significantly enhanced by introducing 0.1 wt% CuO nanoparticles, with a first absorption carbon capacity of 0.09952 g CO 2 ·g −1 absorbent. In the first cycle of regeneration, [email protected] % CuO nanofluid had a carbon capacity of 0.07654 g CO 2 ·g −1 absorbent, achieving an efficiency improvement of 35.73 %. Its regeneration energy consumption was reduced by 0.3256 GJ·t -1 CO 2 , representing a 15 % decrease compared with the base liquid. The cyclic absorption capacity was enhanced significantly after the addition of CuO, with a CO 2 capacity at 0.0690 g CO 2 ·g -1 absorbent after four cycles. The characterization of CuO revealed the stability of nanoparticles in nanofluids. In addition, it was found that the nanoparticles exhibited phase-transfer characteristics. After absorption, they accumulated in the rich phase and then became uniformly distributed throughout the entire liquid phase following regeneration. This behaviour could promote a more efficient desorption process. This study provides a new approach for green chemistry and carbon capture applications.
✓ 已验证
产品关联
DOI
高影响因子
Advanced Sustainable Systems
·
2025
·
IF 6.1
Qin Peng,Zhenxing Shen,Xinyu Mo,Tian Chang,Bo Song,Hao Fan,Zhenchuan Niu
The incorporation of functionalized secondary metal nodes into bimetallic metal–organic frameworks (MOFs) enhances their performance and application potential. This study investigates Cu/Zn-MOF-74 catalysts with varying metal ratios for carbon dioxide (CO₂)-epoxide cycloaddition. Compared to monometallic Cu-MOF-74 and Zn-MOF-74, the bimetallic system shows superior catalytic activity for epoxides conversion. Vim─COOH@Cu/Zn-MOF-74 is developed by introducing hydrogen bond donors (HBD) and nitrogen-containing linkers. The optimal Vim─COOH@Cu₀.₆₇Zn₀.₃₃-MOF-74 demonstrates outstanding performance in CO₂-epichlorohydrin cycloaddition, achieving 96.4% conversion and 98.5% selectivity under mild conditions (80 °C, 1.0 MPa, 24 h) without co-catalysts, while maintaining excellent recyclability. Using a one-pot synthesis, bimetallic MOFs with controlled Cu/Zn ratios are prepared. The framework is further modified by incorporating 1,4-butanediyl-3,3′-bis-1-vinylimidazolium bromide and HBD-functionalized imidazole bromide monomers. The resulting composites achieve over 80% conversion under solvent-free, co-catalyst-free conditions due to synergistic effects between Lewis acid sites, carboxyl groups, and nucleophilic Br⁻ ions. This work presents an effective strategy for developing efficient MOF catalysts for CO₂ conversion. The Vim─COOH@Cu/Zn-MOF-74 system demonstrates significant potential for sustainable CO₂ utilization in cyclic carbonate synthesis, combining high activity, selectivity, and stability under environmentally friendly reaction conditions.
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2025
·
IF 9
Tao Pu,Yanping Li,Xiujuan Yang,Ran Ao,Quxiu Dai,Jie Yang,Zhiying Guo,Liping Ma,Zhanghong Wang
Silicoaluminophosphate-20 (SAPO-20) molecular sieve was synthesized from solid waste coal gangue (CG) and aluminum ash (Al-ash), and its adsorption capacity for CO 2 was evaluated. The content of Si and Al in raw materials was increased by hydrochloric acid pretreatment, and the synthesis conditions (NaOH/CG ratio, calcination temperature, hydrothermal reaction temperature and time, liquid–solid ratio) were optimized by single factor analysis. The synthesized products were characterized by XRD, SEM, BET, FTIR and TEM. The results showed that the SAPO-20 crystal form prepared under the optimal conditions had high purity, BET surface area of 175 m 2 /g, and pore structure with multistage pore distribution, which was conducive to gas diffusion and adsorption. Thermogravimetric analysis revealed that under the conditions of 25 °C and 1 bar, compared with the CO 2 adsorption capacity of 5.63 mg/g for CG, the CO 2 adsorption capacity of SAPO-20 was 27.92 mg/g. The adsorption process was in line with the Langmuir monolayer model and had exothermic characteristics (ΔH = –152 kJ/mol). The adsorption kinetics was fitted by Pseudo-First-Order Kinetic Model (R 2 = 0.740–0.995), and the adsorption rate increased with the increase of temperature. In addition, compared with the traditional synthesis method, the synthesis cost of this study was reduced by more than 70 %, and the carbon emission was reduced by about 75 %, realizing economic and environmental viability.
✓ 已验证
产品关联
DOI
高影响因子
Catalysis Science & Technology
·
2025
·
IF 4.2
Congyu Qin,Shuchen Xing,Guiming Ba,Huilin Hu,Jinhua Ye,Defa Wang
Photothermocatalytic carbon dioxide (CO2) reduction into value-added chemicals is one of the promising methods for solar-to-chemical energy conversion. However, it remains a challenge in the improvement of catalytic activity and product selectivity in view of practical applications. Herein, we report a facile “two-step” approach – nitrogen treatment of Ti3C2 MXene (TC) and loading of Co nanoparticles – to synthesize a Co-nanoparticle/layered TiO2-TiN (Co/TiO2-TiN) composite as an efficient photothermocatalyst for selective reduction of CO2 to methane (CH4). In contrast to the Co/Ti3C2 catalyst that shows a high CO selectivity, the optimal 35Co/TiO2-TiN catalyst exhibits a CH4 evolution rate of 45.5 mmol gcat−1 h−1 with 99.3 % selectivity under a 300 W Xe lamp irradiation. The synergistic effect of increased light absorption capacity, reactive sites, CO2 adsorption/activation ability, and desorption energy barrier of CO* intermediate by the loaded Co nanoparticles and the formation of Ti−N−O bonds accounts for the significantly enhanced photothermocatalytic performance of 35Co/TiO2-TiN for selective CO2 reduction into CH4. Our work demonstrates that metal nanoparticle loading and formation of Ti−N−O bonds can be integrated into the strategy in developing a photothermocatalyst for efficient CO2 reduction with controlled product selectivity.
✓ 已验证
产品关联
DOI
高影响因子