文献检索

查找使用阿拉丁产品的科研文献

检索与阿拉丁产品相关的同行评审论文、DOI、PubMed 编号、期刊、作者、CAS 号及研究领域。

科研影响力快照

与阿拉丁产品相关的已发表科研成果

在搜索之前,这些指标可帮助访客快速了解产品关联科研的规模与质量。

347,389+ SCI 论文 与阿拉丁产品引用相关
2,303,681.05 总影响因子 匹配文献记录中影响因子的总和
81.20 最高期刊影响因子 匹配期刊中的最高 IF
6.63 平均期刊影响因子 匹配文献的平均 IF

参考指标 指标基于阿拉丁文献引用数据库及期刊影响因子记录。文献关联仅供科研参考,请以原始文献为准。

产品列表

视图 列表 网格

显示第3013至3024个,产品总数11,257个

切换升序
CO
Functional Materials Letters · 2025 · IF 1.1

Enhanced ionic conductivity of Ga/Nb Co-doped LLZO ceramic electrolyte via sintering regime optimization

Jie Zhao,Ming Guan,Can Cui,Saifang Huang

To enhance the room-temperature lithium-ion conductivity and interfacial stability of Li 7 La 3 Zr 2 O 1 2 (LLZO) solid-state electrolytes, a co-doping strategy with Ga 3 + and Nb 5 + was employed. By systematically optimizing the sintering protocol — including heating rate, temperature, and dwell time — highly dense and phase-pure cubic-phase LLZO ceramics were successfully synthesized. The co-doping approach effectively stabilized the cubic garnet structure and regulated the lattice framework to facilitate Li + transport pathways. Under optimized conditions, compared to undoped LLZO (0.31 mS cm − 1 , 0.362 eV), the co-doped ceramic exhibited significantly enhanced total ionic conductivity (0.81 mS cm − 1 ) and reduced activation energy (0.207 eV), confirming the superior transport performance enabled by the co-doping strategy. Furthermore, the electrolyte showed good wettability and interfacial compatibility with metallic lithium, enabling stable cycling performance in symmetric Li∥Ga/Nb-LLZO∥Li cells over short durations. These results confirm the practical potential of the co-doped LLZO electrolyte in all-solid-state lithium batteries. This study provides a viable pathway for the material design and processing of high-performance LLZO-based solid electrolytes.

CAS / MDL: 12024-21-4 1313-96-8
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CRYSTENGCOMM · 2025 · IF 2.6

NiRu catalysts supported on η-Al2O3 for selective methanation of CO in H2-rich gases

Zhihui Li,Xinfa Dong

Among the various methods for removing carbon monoxide (CO) from hydrogen-rich (H2-rich) gases, carbon monoxide selective methanation (CO-SMET) has become one of the most effective ones, bringing considerable advantages in terms of performance, environmental sustainability and cost. A bimetallic NiRu/η-Al2O3 catalyst with Ni–Ru alloy phases was prepared and its performance in the removal of CO through a selective methanation process was examined in this study. Also, a comparison was made with the NiRu/γ-Al2O3 catalyst. The NiRu/η-Al2O3 catalyst demonstrated excellent CO-SMET performance, reducing the CO concentration to below 10 ppm with over 50% selectivity between 215 and 300 °C. Its excellent catalytic performance can be ascribed to numerous Ni active sites, increased oxygen vacancies, and more acidic sites. Additionally, the NiRu/η-Al2O3 catalyst had the ability to resist sintering because of the formation of Ni–Ru alloy on it. Moreover, it also exhibited good catalytic stability.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
FUEL · 2025 · IF 7.5

PtM (M = Fe, Co, Ni) alloys as highly efficient catalysts to the oxygen reduction reaction

Xudong Leng,Luxuan Huang,Yongjin Sun,Xuekun Jin,Fengjuan Chen,Haiming Duan,Biaobing Cao

Platinum-based alloy catalysts have achieved notable progress in oxygen reduction due to their unique electronic structures, but conventional alloying often causes nanoparticle agglomeration and sintering. Here, PtM (M = Fe, Co, Ni) alloys are synthesized using XC-72R carbon black as support. PtFe nanoparticles (∼3.1 nm) are uniformly dispersed and exhibit strong electronic interactions, optimizing the Pt electronic structure. The Pt 2 Fe 1 /C catalyst delivers a half-wave potential of 0.849 V, with mass and specific activities 1.57 and 3.31 times higher than commercial Pt/C, retaining 94.4 % activity over 9 h. It also exhibits excellent hydrogen evolution performance, requiring only 36 mV overpotential at 10 mA cm −2 . Density functional theory indicates that alloying downshifts the Pt d-band center, reducing *OH adsorption energy and enhancing catalytic activity. This work demonstrates a synthesis strategy for stable Pt alloys with superior bifunctional performance in both oxygen reduction and hydrogen evolution reactions.

CAS / MDL: 31175-20-9
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY · 2025 · IF 8.3

Fast synthesis of lamellar TiO2 for promoting photocatalytic H2 evolution with low co-catalyst loading

Xiaoyu Wang,Peng Li,Mingyue Yang,Jianwei Zhao,Tao Wang,Dong Hao

Two-dimensional materials have garnered significant attention in recent years due to their remarkable electron-hole transfer capability. However, the advancement of convenient and rapid synthesis techniques remains crucial for further research in this field. In this study, lamellar anatase/rutile-TiO 2 phase heterojunctions with a favorable phase interface was synthesized through a fast annealing route using glucose as the template and titanium tetrachloride. The sample synthesized at 600 °C with a holding time of 20 min exhibited the most significant levels of H 2 evolution activity (53.22 mmol g −1  h −1 ) with a low loading of 0.05 wt% Pt co-catalyst, which is significantly higher than the commercial P25 sample. The characterization reveals that the anatase/rutile-TiO 2 phase heterojunction in the two-dimensional sheet exhibits excellent phase interface contact and possesses a large specific surface area with an appropriate pore size. These characteristics are advantageous for facilitating the separation and migration of carriers, thereby enhancing the efficiency of the H 2 production reaction through hydrolysis. This study presents a novel approach towards the advancement of highly effective two-dimensional photocatalysts.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
MOLECULES · 2025 ·Vol. 30 ·期 9 ·1945 · IF 4.6

Structural Investigation and Energy Transfer of Eu3+/Mn4+ Co-Doped Mg3Ga2SnO8 Phosphors for Multifunctional Applications

Zaifa Yang

In recent years, rare earth ion and transition metal ion co-doped fluorescent materials have attracted a lot of attention in the fields of WLEDs and optical temperature sensing. In this study, I successfully prepared the dual-emission Mg3Ga2SnO8:Eu3+,Mn4+red phosphors and the XRD patterns and refinement results show that the prepared phosphors belong to the Fd-3m space group. The energy transfer process between Eu3+and Mn4+was systematically investigated by emission spectra and decay curves of Mg3Ga2SnO8:0.12Eu3+,yMn4+(0.002 ≤ y ≤ 0.012) phosphors and the maximum value of transfer efficiency can reach 71.2%. Due to the weak thermal quenching effect of Eu3+, its emission provides a stable reference for the rapid thermal quenching of the Mn4+emission peak, thereby achieving good temperature measurement performance. The relative thermometric sensitivities of the fluorescence intensity ratio and fluorescence lifetime methods reached a maximum value of 2.53% K−1at 448 K and a maximum value of 3.38% K−1at 473 K. In addition, the prepared WLEDs utilizing Mg3Ga2SnO8:0.12Eu3+phosphor have a high color rendering index of 82.5 and correlated color temperature of 6170 K. The electroluminescence spectrum of the synthesized red LED device by Mg3Ga2SnO8:0.009Mn4+phosphor highly overlaps with the absorption range of the phytochrome PFRand thus can effectively promote plant growth. Therefore, the Mg3Ga2SnO8:Eu3+,Mn4+phosphors have good application prospects in WLEDs, temperature sensing, and plant growth illumination.

✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
Journal of Environmental Chemical Engineering · 2025 ·Vol. 14 ·期 1 ·120662 · IF 7.2

Directional selection mechanism of single atom catalyst Co-S-C/CB regulating peroxymonosulfate radical pathway

Bin Ou,Hongwei Rong,Baihui Cui,Jie Zhang,Fang Zhang,Dabin Guo

The coordination calcination method is used to form a coordination complex between Co 2 + and thiophene, which is adsorbed on carbon black (CB) and then calcined to prepare Co-S-C/CB single atom catalyst. Co-S-C/CB could efficiently activate peroxymonosulfate (PMS) by forming Co-S 3 coordination structure and Co-S 3 is the active site for activating PMS. Electron rich region was formed on the Co atom and the Co atom could keep in a low valence state during the catalytic process and donate electrons to PMS to produce radicals (•OH and SO 4 •- ) through a single-electron-reduction. Co-S-C/CB could not only promote PMS to generate •OH and SO 4 •- , but also inhibit the generation of 1 O 2 and O 2 •- . The radical pathway has the lowest Gibbs free energy (ΔG) compared to the 1 O 2 pathway and the Co(IV)=O pathway. Therefore, Co-S-C/CB could regulate the radical pathway of PMS. •OH and SO 4 •- are mainly responsible for the removal of Rhodamine B (RhB). Co-S-C/CB could be applied to efficiently degrade various organic pollutants and has good stability. Macro preparation of Co-S-C/CB could be achieved from both the preparation process and raw material aspects.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY · 2025 · IF 3.7

Synergistic mechanism of green corrosion inhibitors COS and CMC-Na in Co electrochemical mechanical polishing

Chunlin Cai,Min Zhong,Meirong Yi,Xiaobing Li,Jianfeng Chen,Wenhu Xu

Electrochemical mechanical polishing (ECMP), through the introduction of electric field, promotes the chemical reaction during polishing. However, the addition of electric field will accelerate the oxidative corrosion, at this time the effective corrosion inhibitor must be added in the polishing solution. Nevertheless, most traditional corrosion inhibitors are toxic and inhibition efficiency is low. In order to meet this technical challenge, this paper investigates the effect of two green corrosion inhibitors, chitosan oligosaccharide (COS) and carboxymethylcellulose sodium (CMC-Na), on Co ECMP, and compares them with the traditional inhibitor TAZ. The results show that when COS and CMC-Na are added at the same time, the polished Co surface quality can be greatly improved, and the surface roughness decreases by 94.6 %. It indicates that adding COS and CMC-Na simultaneously can play the best corrosion inhibition effect and achieve the best surface quality. The synergistic behavior and action mechanism of COS/CMC-Na are analyzed by polishing experiments, static corrosion, electrochemical tests, XPS, and AFM. This study provides a reference for the development of green polishing solutions for Co ECMP.

CAS / MDL: 9004-32-4 1317-42-6
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
npj Flexible Electronics · 2025 · IF 15.5

Regionally controlled ion-doping of organic electrochemical transistors for computing-memory co-integrated neuromorphic systems

Li Mancheng,Zhang Wenjing,Lv Xinyang,Liang Xiaoci,Wang Mengye,Chen Chen,Liu Chuan,Han Songjia

Organic electrochemical transistors (OECTs), endued with processing and memory functionalities, present a remarkable potential for neuromorphic electronics. However, integrating processing and memory cores for neuromorphic systems is complicated by heterogeneous material compatibility and device architecture constraints. Here, we demonstrate a versatile regionally controlled ion-doping strategy for modulating the operational mode of OECTs between high-performance computing and non-volatile memory, without varying the materials or operating conditions. The key to this method is the use of inkjet-printed electrolytes with programmable 3D architectures, which can be precisely deposited onto the OECT channel, achieving a tunable thickness ranging from 100 nm to several tens of micrometers. By engineering the electrolyte’s spatial structure, we demonstrate two complementary OECT configurations: ion-rich OECTs with multilayer electrolytes achieve high stimulus-resolution capability of 1 ms for dynamic computation, and ion-deficient OECTs with single-layer electrolytes establish stable ion-trapping memristive states (300 s retention). Moreover, the integration of ion-rich and ion-deficient OECTs enables a neuromorphic circuit capable of simultaneous encoding and storage of alphanumeric information. This study presents a simple yet effective strategy that overcomes material compatibility constraints and simplifies circuit design, paving the way for highly integrated neuromorphic systems based on OECTs.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Advanced Optical Materials · 2025 ·Vol. 13 ·期 13 ·2403289 · IF 7.2

Double Perovskite Scintillators Enabled by Co-Doped Trap Regulation for Thermally Enhanced X-Ray Imaging

Renyan Huang,Xiong Zhang,Xieming Xu,Yi Zheng,Xin Huang,Min Chen,Shuaihua Wang,Shaofan Wu

Scintillation materials play a significant role in the exploration of extreme space environments and high-energy physics. Nevertheless, due to the prevalence of thermal quenching, most traditional scintillators are not capable of stable X-ray imaging at high-temperature working mode. In this work, Ce 3+ and Tb 3+ ions are successfully co-doped into Cs 2 NaGdCl 6 double perovskites (DPs) via a solvothermal method, exhibiting unusual thermally enhanced scintillation performance. Specifically, the radioluminescence intensity of Cs 2 NaGdCl 6 :Tb 3+ /Ce 3+ increases with temperature to achieve a large intensity ratio of 3.67 from 80 to 500 K. Interestingly, the introduction of co-doped ions brings the dramatic increase of thermoluminescence intensity, demonstrating that an increased number of deep trap results in the suppression of the thermal quenching. At the same time, the extra occurrence of deep traps can be traced to localized octahedral distortions around the dopant ions. Moreover, a flexible DP-based scintillation film is fabricated by a direct coating method, showing thermally enhanced X-ray imaging. Ultra-stable X-ray imaging performance over 5 h is realized under a high temperature of 380 K by the scintillation film. The results provide a trap regulation strategy for exploring novel high-performance and stable scintillators at high temperatures.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
DIAMOND AND RELATED MATERIALS · 2025 · IF 5.1

CFs@Co3O4/Co(OH)2 absorbent derived from cottonwood fibers pyrolysis for electromagnetic wave absorption

Chenjie Liu,Yijin Wang,Wenlong Xu,Ming Zhou,Fuliang Meng,Xianfeng Meng

In light of electromagnetic pollution caused by the excessive or unregulated use of electromagnetic waves (EMWs), there is an urgent requirement to identify economical EMWs absorption materials. However, the facing challenge lies in the precise design of microstructure and the controlled tuning of electromagnetic parameters. Herein, natural cottonwood fiber was converted into carbon fiber (CF) through optimized pyrolysis, followed by the synthesis of CFs@Co 3 O 4 /Co(OH) 2 composites via in situ hydrothermal method. Ingenious structural design, multi-faceted synergy and heterogeneous interfaces endowed the CFs@Co 3 O 4 /Co(OH) 2 composites with exceptional impedance matching and electromagnetic loss, showing outstanding EMWs absorption ability. The CFs@Co 3 O 4 /Co(OH) 2 sample (CF S @Co-25) with 2.5 mm thickness displayed a maximum reflection loss ( RL max ) of −78.7 dB and an effective absorption bandwidth ( EAB ) of 9.9 GHz. At 3.0 mm matching thickness, the impedance matching value ( Z ) reached 0.99, with an RL max of −105.3 dB. This work offers a scalable and economical approach to developing high-performance carbon-based EMWs absorbers.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
FOOD RESEARCH INTERNATIONAL · 2025 · IF 8

Co-fermentation of Hanseniaspora uvarum and Saccharomyces cerevisiae improves flavor in low-alcohol peach beverages

Haiyan Yu,Lei Shi,Chen Chen,Chang Ge,Xin Pan,Qian Chen,Huaixiang Tian

Isolation, selection and aroma characterization of native non- Saccharomyces yeasts are key for developing novel-flavored low-alcohol beverages. To screen non- Saccharomyces yeasts for alcohol reduction and aroma enhancement in low-alcohol yellow peach beverages, 327 yeast strains were isolated from the spontaneous fermentation processes in various fruits. Following colorimetric alcohol assays and the olfactory method, nine Hanseniaspora uvarum ( H. uvarum ) with low-alcohol and high-aroma phenotypes were selected for co-fermentation with Saccharomyces cerevisiae ( S. cerevisiae ). The alcohol content of most co-fermentation product was below 1.5 % (v/v), with reduced total acidity (contributing to mellow taste) compared to the single S. cerevisiae fermentation. The co-fermentation of H. uvarum and S. cerevisiae elevated terpenes and esters, particularly ethyl acetate, propionate, decanoate, and phenylethanol with this effect being most pronounced in Y112 + JM9 co-fermentation, thereby improving fruity/floral aromas. Sensory evaluations confirmed superior acceptability, validating H. uvarum – S. cerevisiae co-fermentation as a promising strategy for low-alcohol beverage production.

CAS / MDL: 123-96-6 64-17-5 71-23-8
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS · 2025 · IF 4.6

Study on efficient electrolytic Co removal and structural properties of PDC via complexing agent regulation

Houzhen Chen,Fuming Deng,Xiaotian Xing,Miao Gu,Jing Duo,Zhenhai Guo,Zhangjie Ye,Wenli Deng,Ziyi Liu,Qiang Chen,Yefei Zhang,Lei Zhang

In order to minimize the influence of metallic Co on the structural properties of polycrystalline diamond compact (PDC), this study employed an efficient electrolytic Co removal process to investigate the mechanism of complexing agents—Glycine (Gly), Citric Acid (CA), Tartaric Acid (TA), and Ethylene Diamine Tetraacetic Acid (EDTA)—in the electrolytic Co removal from PDC. The results show that Gly performed significantly better than CA, TA, and EDTA in Co removal from PDC. At the Gly concentration of 0.08 mol/L, the Co removal depth and Co removal rate reached 635 μm and 90.77 %, respectively, after 4 h of electrolysis. This significantly improves the efficiency of Co removal and enhances the abrasion ratio of PDC. Furthermore, Gly effectively relieved internal stresses within PDC and formed interconnected pore structures between diamond particles. These changes reduced the risk of delamination and cracking caused by residual stresses, thereby enhancing the service reliability of the material.

CAS / MDL: 162303-59-5
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
已复制

文献关联基于可获得的产品、CAS、DOI 及引用记录。收录不代表作者或出版方对阿拉丁产品的背书,请以原始文献为准。