BIOMASS & BIOENERGY
·
2022
·
IF 5.774
Bang Yao,Qinhao Kang,Jie Fu,Yang Liu,Wenya Ao,Long Wang,Zhihui Jiang,Tianhao Zhang,Yongmeng Song,Zeyu Deng,Asif Ali Siyal,Jianjun Dai
Experiments were carried out to investigate cellulose and furfural from catalytic hydrolysis of corncob. This process improved the comprehensive utilization of hemicellulose and cellulose in biomass resources. Influence of factors (temperature, reaction time, concentration of catalysts, liquid to solid ratio (LSR)) on hydrothermal characteristics, furfural yield, properties and retention of cellulose were investigated through orthogonal and parameter tests. Acetic acid (6 wt%) and FeCl 3 (40 mM) achieved the highest furfural yield (47.60%) and relatively high cellulose retention ratio (71.84%) at 180 °C, 45 min, and 3 mL/g of LSR. While AlCl 3 and citric acid obtained low furfural yield and the lowest cellulose retention ratio (8.38%). Furfural was dominant in distillated organics (GC-MS areas ≥97.9%), by contrast furfural, 5-hydroxymethyfurfural and vanillin were main organics in residual liquors. The peak of furfural yield switched to shorter reaction time as temperature increased. Combination of AlCl 3 with acetic acid and citric acid accelerated cellulose degradation. NaCl inhibited furfural yield and promoted lignin decomposition. Higher temperature and greater concentration of FeCl 3 contributed to reduced crystallinity of cellulose during hydrothermal treatment.
✓ 已验证
产品关联
DOI
高影响因子
CARBOHYDRATE POLYMERS
·
2022
·
IF 10.723
Xuchu Yin,Tao Zhang,Tongqing Zhao,Ke Wang,Zhiguang Xu,Yan Zhao
Cellulose-based, closed-cell porous materials templated from emulsions are promising for thermal insulation, but their low stability imposed by physical interaction hinders the materials from real applications. Herein, we report the fabrication of cellulose-based, flexible polyurethane polyHIPEs with quasi-closed-cell structures, high stability and flexibility for thermal insulation. The polyHIPEs were prepared from cellulose-stabilized Pickering high internal phase emulsions through interfacial crosslinking using isocyanate . The resulting polyurethane polyHIPEs showed controllable external shapes, quasi-closed-cell structures, high flexibility, low density, and robust compression (without fracture even after compression to 30 % original height). The crosslinking enabled the polyHIPEs to show hydrophobicity , good stability (without breakage and dissolution observed after immersing in NaOH solution at pH 12, HCl solution at pH 1 and hot water at 100 °C, for 24 h) and decreased moisture uptake (below 1 %). The low density and quasi-closed-cell structures endowed the polyHIPEs with high thermal insulation, with thermal conductivity as low as 33.1 mW/(m K). These features make the cellulose-based, closed-cell polyHIPEs as an excellent candidate for thermal insulting.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2023
·
IF 9.9
Wanxia Luo,Nannan Guo,Luxiang Wang,Dianzeng Jia,Mengjiao Xu,Su Zhang,Lili Ai,Rui Sheng,Shizhan Feng,Xinyi Gong,Yali Cao
Porous carbons have been widely applied for capacitive energy storage, yet usually suffer from insufficient rate performance because of the sluggish ion transport kinetics in deep and multi-branched pores. Herein, we fabricated an interconnected microporous capacitive carbon (IMCC) by growing D (+)-glucosamine on bacterial cellulose (BC) nanofibers scaffold, followed by carbonization and activation. The BC nanofibers acted as a sacrificial template during pre-carbonization, facilitating the subsequent KOH permeation and homogeneous activation. By taking advantage of the interconnected microporous structure, the IMCC delivers a high capacitance of 302 F g −1 at 1 A g -1 and an excellent rate capability of 165 F g −1 at 100 A g -1 for aqueous supercapacitor , demonstrating its fast ion transport capability. Impressively, it also shows a superior gravimetric capacity of 177 mAh g -1 at 0.5 A g -1 and remains a high value of 72 mAh g -1 at 20 A g -1 as a cathode material for Zn-ion hybrid capacitor. This facile and cost-effective design strategy exhibits a great potential to construct carbohydrates-derived interconnected microporous carbon materials for high-rate energy storage.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2023
·
IF 15.1
Pengxiang Yin,Yu Geng,Lunyu Zhao,Qiujie Meng,Ziyan Xin,Liushan Luo,Bijia Wang,Zhiping Mao,Xiaofeng Sui,Wei Wu,Xueling Feng
Harvesting the ubiquitous low-grade heat based on thermoelectric materials is an effective approach to ensure sustainable development . Quasi-solid thermogalvanic cell based on hydrogel has attracted considerable attention. However, challenge arise from the limited working temperature range and poor mechanical properties, thus severely restrict their long-term stability and application scenarios, especially under harsh environment. Herein, a robust, flexible and eco-friendly quasi-solid thermogalvanic cell is reported based on natural polymer bacterial cellulose confined with Fe(CN) 6 3−/4− redox couple and hygroscopic salts. The as-fabricated bacterial cellulose-based thermogalvanic cell (BC-TGC) possesses excellent mechanical properties, exhibiting a tension strength of 3.4 MPa, a Young's modulus of 2.58 MPa and a high toughness of 644.6 KJ m −3 . The introduction of hygroscopic salts (LiBr) endows the BC-TGC with excellent anti-drying and anti-freezing properties. The thermoelectric performance of BC-TGCs was investigated thoroughly, which could generate steady electricity under a small temperature gradient in a wide working range of −50 to 50 °C. The multifunctional applications of the BC-TGC were demonstrated, indicating that they could adapt to different temperatures and harsh environments, which greatly expanded the application scenarios of TGC. We expect that this study will provide an effective solution for portable, flexible and robust power supplies fabrication for low-grade heat harvesting.
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Nano Materials
·
2022
·
IF 6.14
Zhaosong Hu,Yingchun Liu,Jinxin Lin,Haohan Wu,Bowen Liu,Weiqi Guo,Xuliang Lin,Liheng Chen,Xueqing Qiu,Yanlin Qin
High-thermal-conductivity (λ) nanocomposites have been thought to resolve thermal management issues in electronic development. However, use of these is still challenging due to the easy aggregation of micro/nanofillers in a matrix. Here, a high-efficiency, low-cost, environmental strategy was developed wherein pyrene-functionalized alkali lignin (AL-PPBA) dispersants were employed to disperse hydroxylated boron nitride nanosheets (BNNS) by π–π conjugation in a cellulose nanofiber (CNF) solution, following which a nanocomposite film was prepared via the vacuum-assisted self-assembly method. Experimental and simulation results show that an efficient interfacial interaction between AL-PPBA and BNNS was achieved successfully and a stable aqueous dispersion solution was obtained. The as-prepared nanocomposites thus show λ as high as 18.27 W m–1 K–1 with the loading of 10.4 vol % of BNNS and superior anisotropy. A potential thermal management capability was demonstrated when using nanocomposites as heat sink components for light-emitting diode (LED) chips. This study provides a route to promote the dispersity of micro/nanofillers via a noncovalent cross-linking strategy and address heat management issues.
✓ 已验证
产品关联
DOI
高影响因子
FOOD CHEMISTRY
·
2023
·
IF 8.8
Jianhui Zhu,Jingyang Yu,Bingjie Zhang,Changsheng Li,Jianli Wang,Jiawen Ji,Desheng Liu,Rumin Gao,Jianzhang Li,Yongqiang Ma
The abuse of organophosphorus pesticides (OPPs) in tea planting makes it easy to transfer from tea into its infusion, bringing potential health risks to consumers. Thus, it is essential to adopt reliable techniques to remove OPPs from tea infusion. In this study, three treatment methods were used to modify carbonized bacterial cellulose (CBC) to improve its adsorption performance. Among them, CBC treated by hydrazine hydrate ( N -CBC) had the best adsorption effect, whose removal rate for dicrotophos is 13 times that of CBC. The in-depth study of adsorption mechanism proved that hydrophobic interaction dominated the adsorption of OPPs onto N -CBC. The pseudo-second-order kinetic model and Langmuir isotherm model were more suitable to describe the process. Additionally, there were no significant changes in tea infusion quality after N -CBC treatment. This work clarifies that N -CBC benefitted from simple preparation method, excellent adsorption performance and unique adsorption mechanism has potential applications in tea infusion.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ACS Applied Nano Materials
·
2023
·
IF 5.9
Jialu Yang,Bochong Wang,Hanxin Liao,Jianyong Xiang,Congpu Mu,Anmin Nie,Kun Zhai,Tianyu Xue,Fusheng Wen
Flexible electromagnetic interference (EMI) shielding materials are in urgent need in the flexible and wearable electronics fields. In this study, multifunctional flexible silver-coated carbon nanofibers/bacterial cellulose (Ag/CNFs/BC) films were fabricated by vacuum filtration equipment using bacterial cellulose as a flexible substrate. Silver-coated carbon nanofibers were prepared by the chemical deposition method, and the silver was uniformly coated on the surface of carbon nanofibers with scanning electron microscopy (SEM) observation. Compared with the carbon nanofibers/bacterial cellulose (CNFs/BC) films, the EMI performance of Ag/CNFs/BC films was greatly enhanced because of the improvement of conductivity up to 4184 S/m. The EMI shielding effectiveness was highly enhanced over 55 dB in the X-band (8–12 GHz) under a relatively low thickness of 34 μm for the Ag/CNFs60/BC film. Moreover, the Ag/CNFs60/BC film also showed great multifunctional thermal applications. A Joule heating of over 110 °C at 3 V direct current and a photothermal conversion over 60 °C under an optical power density of 100 mW/cm2 were achieved. These results indicated that the Ag/CNFs/BC films with nanomaterials have huge application potential as flexible wearable self-heating products with excellent electromagnetic shielding performances.
✓ 已验证
产品关联
DOI
高影响因子
MATERIALS & DESIGN
·
2023
·
IF 8.4
Chenjuan Xiao,Yukun Yan,Guodong Wen,Yangtao Zhou,Duo Na,Chengling Yang,Jinsong Zhang
This work developed a simple and mild strategy for controllable synthesis of highly and homogeneously distributed TiO 2 nanoparticles on a cellulose template via tuning the cellulose crystallinity. As the crystallinity of cellulose increases, the restriction from crystallinity on nanoparticles increases, leading to homogeneous distribution, a decrease in size, and structural changes of TiO 2 from crystalline to amorphous. The carboxyl groups grafted on the periodically arranged hydroxyl groups of crystalline cellulose, which act as anchor sites for metal oxide precursor, restrict the distribution, growth and crystallization of TiO 2 nanoparticles. The amorphous TiO 2 nanoparticles on the cellulose with the highest degree of crystallinity (72.40 %) give the highest adsorption capacity toward tetracycline hydrochloride (152.89 mg/g), which is the state of art among the supported TiO 2 . The high adsorption capacity is proposed to be the oxygen defects caused by the Ti 3+ species, originating from the amorphous TiO 2 nanoparticles.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Environmental Chemical Engineering
·
2022
·
IF 7.968
Shuang Zheng,Shujuan Yang,Zhaofeng Ouyang,Tianya Chen,Yong Kuang,Haixing Shen,Fei Yang,Yong Zhang
To obtain ultrafiltration (UF) membranes with excellent separation performances and antifouling properties, regenerated cellulose (RC) membranes with intrinsic hydrophilicity and dense structures immensely attract the attention of researchers. Herein, a novel modified RC membrane, which has high water permeability and antifouling capability, is prepared using cellulose acetate (CA) via non-solvent induced phase separation (NIPS) and green hydrolysis technology . The as-prepared membranes were investigated comprehensively by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) analyses and protein adsorption, etc. As a result, the RC membranes showed higher hydrophilicity (WCA=25.95°), thus they possessed a lower protein adsorption value of 1.9 ± 0.1 μg/cm 2 . The filtration performances were evaluated by bovine serum albumin (BSA) and endotoxin separation with dead-end filtration system. The results exhibited greater selectivity of RC membranes that BSA rejection over 98% and endotoxin remove below 0.25 EU/mL, and excellent anti-fouling properties that the flux recovery rate (FRR) over 95% and even as high as 100%. Simultaneously, the common polyethersulfone (PES) composite membranes were prepared via NIPS technology, and comprehensively compared with RC membranes to provide a theoretical basis for the practical application of RC membranes in pharmaceutical and biotechnological industries.
✓ 已验证
产品关联
DOI
高影响因子
Polymers
·
2022
·Vol. 14
·期 23
·5080
·
IF 4.967
Leixuan Li,Yan Xin,Fengze Wu,Xiangrong Lyu,Qiyuan Yao,Xiaoting Yin,Qiang Zhang,Wenjuan Shan,Yong Chen,Qiuxia Han
CyclicN-halamines are highly antimicrobial, very stable, and not susceptible to bacterial resistance. A polysiloxane delivery vehicle was synthesized to deliver cyclic imideN-halamine onto cellulose via a benign and universal procedure that does not require a harmful solvent or chemical bonding. In brief, Knoevenagel condensation between barbituric acid and 4-hydroxybenzaldehyde furnished 5-(4-hydroxybenzylidene)pyrimidine-2,4,6-trione, whose phenolic O−H was subsequently reacted with the Si−H of poly(methylhydrosiloxane) (PMHS) via silane alcoholysis. The product of silane alcoholysis was interpenetrated into cellulose in supercritical CO2(scCO2) at 50 °C, to form a continuous modification layer. The thickness of the modification layer positively correlated with interpenetration pressure in the experimental range of 10 to 28 MPa and reached a maximum value of 76.5 nm, which demonstrates the ability for tunable delivery, to control the loading of the imide N−H bond originating from barbituric acid unit. The imide N−H bonds on cellulose with the thickest modifier were then chlorinated into N−Cl counterparts usingtert-butyl hypochlorite, to exert a powerful biocidability, providing ~7 log reductions of bothS. aureusandE. coliin 20 min. The stability and rechargeability of the biocidability were both very promising, suggesting that the polysiloxane modifier has a satisfactory chemical structure and interlocks firmly with cellulose via scCO2interpenetration.Keywords:cyclic imideN-halamines;polysiloxane;delivery vehicle;antibacterial surface;cellulose;scCO2interpenetration
✓ 已验证
产品关联
DOI
PubMed
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2022
·
IF 8.025
Heng Zhang,Qiuyue Hu,Tian Si,Xiaoning Tang,Shaoyun Shan,Xin Gao,Lincai Peng,Keli Chen
High-speed shear system is usually used for the dispersion improvement of slurry, nanomaterials preparation, and even two-dimensional materials production. However, there is barely study that focused on the regenerated cellulose (RC) which was coagulated with shear induced. In this work, a new type of all-cellulose air filter was fabricated through high-speed shear in aqueous regeneration system using parenchyma cellulose from corn stalk. The obtained RC were aggregated by ribbon-like fine cellulose and nanocellulose sheets. The study exhibited the micro-structure of RC displayed excellent unidirectional alignment and a relatively high crystallinity. All-cellulose air filter which was produced via RC presented excellent filtration efficiency (PM 2.5 97.3 %, PM 10.0 97.7 %) with slightly pressure drop (19 Pa). Therefore, this work provides a facile method to obtain a novel RC with nanocellulose particles used for air filtration, which gives an effective strategy application in the conversion of all-cellulose materials from agricultural waste.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2022
·
IF 9.965
Chaoyi Zhou,Yunxiao Xie,Yan Li,Bin Li,Yangyang Zhang,Shilin Liu
Hypothesis The effect of the molecular weight and polymer concentration on the partition behavior of aqueous two-phase systems (ATPs) is significant for constructing water-in-water (W/W) emulsions. Hence, a long-term stable W/W emulsion system might be obtained through selecting the appropriate stabilizer and component phases, which could be a possible carrier for probiotics. Experiments Compared with the reported molecular weight difference between polyethylene oxide (PEO) and dextran (DEX) systems, PEO and dextran with lower molecular weight had been used for constructing the water in water (W/W) emulsion system. The W/W emulsions were stabilized using cellulose nanocrystals (CNCs), and the potential application of the W/W emulsion for the encapsulation of Lactobacillus was explored. Findings Emulsion stability exhibited a “dose-effect” relationship with the CNCs concentration and was decreased with the increase of the DEX concentration. The emulsion phase separation rate was increased with increasing ionic strength and temperature. Both Lactobacillus Plantarum and Lactobacillus helveticus were highly inclined to the DEX phase, and the emulsion droplets were deformed and aggregated when the encapsulation amount was increased. This long-term stability would provide a promising approach for designing high-density culture and fermentation of probiotics.
✓ 已验证
产品关联
DOI
PubMed
高影响因子