Journal of Engineered Fibers and Fabrics
·
2021
·
IF 1.573
Yating Zhang,Shujie Zhang,Lisong Fu,Mengke Jing
Use chitosan (CS) fiber and cellulose acetate (CA) fiber with different mixing ratios as raw materials, the kinetic and thermodynamic characteristics of the adsorption process of chitosan fiber/cellulose acetate fiber (CS/CA) ratio of 90:10 are explored, and the adsorption process conforms to the quasi-second-order kinetic equation. It can be fitted by Langmuir isotherm. The adsorption process is a spontaneous thermal reaction with both physical adsorption and chemical adsorption. The best adsorption time is 30 min, the time to reach adsorption equilibrium is 180 min, and the best adsorption pH is 5, the most suitable temperature is 35°C, and rising the temperature is conducive to the fibers adsorption. The materials before and after the CS/CA blended yarn adsorbed copper ions were characterized by XRD, DSC, FT-IR, and the adsorption mechanism was analyzed. In the orthogonal experiment, the copper ions concentration has the most obvious effect on the adsorption capacity, and the temperature has the most obvious effect on the adsorption efficiency. The optimal adsorption combination is that the mixing ratio of chitosan fiber/cellulose acetate (CS/CA) is 80:20, the pH is 5, the temperature is 35°C, and the copper ion concentration is 100 mg L−1. Comparing the adsorption performance of fibers with different mixing ratios, the adsorption performance of CS/CA ratio of 90:10 is the best. The filtration efficiency of the filter material, made of fibers with different mixing ratios, to copper ions is tested, and the filtration performance with a mixing ratio of 90:10 is the best, and the filtration efficiency is 64.33%.
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Nano Materials
·
2021
·
IF 5.097
Cheng Zhang,Xueqin Zhang,Yinfu Luo,Mei Liang,Huawei Zou
To enhance the interfacial properties of carbon fiber-reinforced polymer (CFRP) composites, chitosan (CS) and carbon nanotubes (CNTs) were used to construct multilayer structures on the surface of the CF. CFs were first encapsulated by CS through hydrogen bonding and electrostatic action to form a uniform membrane with a thickness of 32 nm. Then, CNTs were grafted on the CS layer to obtain a multilayer membrane with a thickness of 45–60 nm, resulting in improved roughness and wettability of CFs. Subsequently, CFRP composites were prepared by impregnating multiscale CFs with epoxy resin. Compared with that of untreated CFRP composites, the interfacial shear strength, transverse fiber bundle tensile strength, and interlaminar shear strength of the CS-encapsulated and CNT-grafted CFRP composites increased by 91.61% (75.61 MPa), 63.61% (32.78 MPa), and 37.73% (83.24 MPa), respectively. This work provides a green and nondestructive method to optimize the interfacial interactions between CFs and the polymer matrix, which can effectively expand the application field of CFRPs.
✓ 已验证
产品关联
DOI
高影响因子
CARBOHYDRATE POLYMERS
·
2021
·
IF 9.381
Kelin Peng,Weizhe Wang,Jinghua Zhang,Yan Ma,Lizhi Lin,Qiang Gan,Yu Chen,Changgen Feng
Conductive hydrogels (CHs) are a potential material for flexible electronics. However, most of CHs display disadvantages of low ionic conductivities and intolerance to low temperatures. Herein, a novel physical CHs with salt contents as high as 30 wt% was prepared with chitosan (CTS) and sodium alginate (SA) by combining the anti-polyelectrolyte effect and semi-dissolution acidification sol-gel transition (SD-A-SGT) method. The obtained hydrogels show extremely high ionic conductivities up to 2.96 × 10 −1 S·cm −1 at room temperature and 4.9 × 10 −2 S·cm −1 at −20 °C. The effects of different salts on the ion mobility and electrochemical properties of CTS/SA CHs were predicted and analyzed. The flexible supercapacitor assembled using CTS/SA CHs as the electrolyte exhibits the specific capacitance as high as 405 F·g −1 at the current density of 0.25 A·g −1 and satisfying electrochemical stability with 74.91% capacitance retention in 1000 cycles. Our work has provided a new strategy for constructing green CHs with high ionic conductivities.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2021
·
IF 7.312
Jie Huang,Bin Huang,Tianxiang Jin,Zhirong Liu,Dejuan Huang,Yong Qian
The extraction of U(VI) from nuclear wastewater is of great importance for environmental protection. In this work, we try to remove uranium ions from uranium-containing wastewater by electrosorption. In order to improve the adsorption capacity and selectivity of the adsorption materials, the complex of chitosan and phytic acid (CSPA) was used as electrode material. The experimental results showed that the introduction of phytic acid can efficiently improve the adsorption capacity, adsorption selectivity and reusability of chitosan. The maximum adsorption capacity of CSPA was 429.1 mg/g and the theoretical maximum sorption capacity reached up to 572.1 mg/g. Moreover, the electrosorption capacity of CSPA for U(VI) was 68.6% of the total electrosorption capacity in the presence of competitive ions. After 5 cycles of reuse, CSPA still maintained 86.6% of its initial sorption capacity. Furthermore, we found that the selective adsorption mechanism of uranium ions was related to the inner-sphere complexation between UO 2 2+ and the O atom of P O group according to the experimental analysis and the DFT calculation results. This work provided a novel strategy for effective removal of uranium (VI) from uranium-containing wastewater.
✓ 已验证
产品关联
DOI
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2021
·
IF 4.539
Yun Liu,Yue-Fei Zhang,Jian Tang,Yuting Tan,Hang Lei,Ying Li,Pengmian Huang,Yan Li
In this study, we developed a novel chitosan-based adsorbent with low cost, high adsorption capacity and marvelous reusability. The adsorbent was prepared in one pot by crosslinking chitosan with acrolein , which was the first attempt to use acrolein as a crosslinking agent to achieve chitosan-based hydrogel (A/CS hydrogel). The A/CS hydrogel not only had the high swelling ratio as many as approximately 1300 times the dry hydrogel, but also has excellent adsorption property for the anion dye acid blue 93 (AB93). Under the optimal adsorption conditions, the adsorption capacity of the adsorbent on AB93 reached up to 1839 mg/g, which realized the ultra-high adsorption capacity. After 12 times of adsorption-desorption cycle, the adsorption rate of the adsorbent to AB93 was still about 90%, which revealed marvelous stability and reusability. The purpose of the present study was to provide a new choice of the elimination and recycle of AB93 and have potential for industrial application.
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2023
·
IF 8.2
Jiyan Li,Yanju Jing,Min Qiao,Wenzhe Yang,Hanxue Sun,Rui Jiao,Junping Zhang,An Li
Solar-driven interfacial evaporation (SDIE) stands out as a prospective technology for freshwater production, playing a significant role in mitigating global water scarcity. Herein, a cyclodextrin polymer/chitosan composite aerogel (PPy-La/Al@CDP-CS) with vertically aligned channels was prepared as a solar evaporator for efficient solar steam generation. The vertically aligned pore structure, achieved through directional freezing assisted by liquid nitrogen, not only improves water transport during evaporation but also enhances light absorption through multiple reflections of sunlight within the pores. The polypyrrole particles sprayed on the surface of the aerogel acted as a light-absorbing layer, resulting in an impressive absorbance of 98.15 % under wetting conditions. The aerogel has an evaporation rate of 1.85 kg m −2 h −1 under 1 kW m − 2 irradiation. Notably, the vertical pore structure of the aerogel allows it to exhibit excellent evaporation performance and salt resistance even in highly concentrated salt solutions. Furthermore, this aerogel is an excellent solar-driven interfacial evaporator for purifying seawater and fluoride-containing wastewater. This photothermal aerogel has the advantages of excellent performance, low cost, and environmental friendliness, and thus this work provides a new approach to the design and fabrication of solar photothermal materials for water treatment.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CELLULOSE
·
2023
·Vol. 30
·期 4
·2441-2452
·
IF 5.7
Yi Caifu,Yuan Tianzhong,Ren Hao,Xiao Huining,Zhai Huamin
With the popularity of air fryer, there is an increasing demand for air frying paper. Here, we successfully prepared an air frying paper with good barrier capacity, cytocompatibility and degradability by coating chitosan, zein and lignin containing cellulose nanofibers (LCNFs), in sequence. The obtained triple-coated paper has a high kit number of 12 and a low Cobb 60 value of 4.93 g/m 2 . Importantly, it had excellent hot oil resistance, which was no penetration even at oil temperature of 210 °C. The triple-coated paper also showed good resistance to ethanol, acid and alkali solutions. These excellent barrier capacities were due to the smooth and dense barrier layer formed by chitosan, zein and LCNFs. Thus, the triple-coated paper was successfully used in the air fryer to fry fries and chicken drumsticks. And the good cytocompatibility and degradability of the coated paper further promote its practical application.
✓ 已验证
产品关联
DOI
高影响因子
DESALINATION
·
2026
·
IF 9.9
Jianling Liu,Jiangnan Zhao,Hanyang Zhao,Hanyu Li,Yan Chen,Jiwei Wang
PDA interlayer enables uniform in situ growth of defective Ce-MOF on chitosan. • Ce-ATA-25PA@PDA@CS achieves a phosphate capacity of 126.6 mg P g −1 . • Phosphate removal reaches 98.6% in real aquaculture wastewater within 60 min. • Synergistic ligand exchange, electrostatic attraction, and H-bonding drive uptake. • The microspheres retain over 68% phosphate removal after five regeneration cycles. The excessive accumulation of phosphate in water bodies can disrupt the ecological balance and pose a threat to human health, highlighting the urgent need for efficient and economically viable adsorbents to treat waters with high phosphorus content. The defective cerium-based metal–organic framework (Ce-MOF) has shown considerable potential for phosphate removal due to its abundant coordinatively unsaturated Ce active sites. However, the high cost of pure Ce-MOF limits its practical application in the large-scale treatment of phosphorus-containing wastewater. In this study, the composite microspheres (Ce-ATA-25PA@PDA@CS) as phosphorus adsorbents were successfully prepared by in situ growth strategy when the new defective Ce-MOF (Ce-ATA-25PA) grew on the surface of the polydopamine coated chitosan microspheres (PDA@CS). The PDA interlayer promoted a denser and more uniform distribution of Ce-ATA-25PA on the chitosan support, and the resulting composite microspheres exhibited an increased specific surface area and a maximum phosphate adsorption capacity of 126.6 mg P/g under the optimized conditions. Mechanistic investigations have shown that phosphate uptake is influenced by the synergistic coupling of multiple interactions: the phosphate uptake involved Ce–O–P interactions at Ce sites together with contributions from the –NH₂ and –OH groups of the PDA@CS support through electrostatic attraction and hydrogen bonding. This work provides presents an environmentally friendly, and efficient MOF/biomass composite adsorbent, which can be used for treating phosphorus-containing wastewater treatment and offers a useful strategy for designing advanced MOF/biopolymer materials for aquatic environmental remediation. Download: Download high-res image (164KB) Download: Download full-size image
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2026
·
IF 8.7
Yongqi Zhang,Jiahao Luo,Jun Liao,Congcong Ding,Mei Tang,Lielin Wang
A PEG-enhanced phosphate modification strategy was proposed for chitosan-SiO 2 aerogel. • PEG improves structural stability while phosphate introduces U(VI)-binding sites. • CSA/PEG-PO 4 exhibits a high U(VI) capacity of 496.98 mg g −1 at pH = 4. • Amino, hydroxyl and phosphate groups synergistically promote U(VI) adsorption. • The aerogel shows potential for efficient uranium removal from acidic wastewater. Uranium contamination has become an important environmental issue because of its toxicity and radiological hazards. In this work, a polyethylene glycol (PEG)-enhanced phosphate-functionalized chitosan-silica hybrid aerogel (CSA/PEG-PO 4 ) was successfully prepared by the sol-gel method and freeze-drying. The structure and surface properties of the aerogel were characterized by XRD, FT-IR, SEM, BET and XPS. Compared with the chitosan/silica aerogel (CSA), PEG modification improved the adsorption performance, while phosphate modification further enhanced the adsorption capacity toward U(VI). The maximum adsorption capacity was 496.98 mg g −1 (pH 4.0, m/V = 1 g L −1 , 150 min, 298 K, 150 rpm), while the removal efficiency reached 97.9%. The adsorbent also showed good selectivity toward U(VI), maintaining removal efficiencies above 87% in the presence of common coexisting ions such as Mg 2+ and Ca 2+ . The pseudo-second-order kinetic model provided a better fit to the adsorption data. Intraparticle diffusion analysis showed that intraparticle diffusion was not the only rate-controlling step. FT-IR and XPS analyses indicated that hydroxyl, amino and phosphate groups were the main active sites for U(VI) adsorption. XRD results confirmed that the aerogel maintained a stable amorphous framework after adsorption, indicating good structural stability during the adsorption process. Overall, CSA/PEG-PO 4 is a promising adsorbent for the efficient removal of U(VI) from aqueous solutions.
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2026
·
IF 8.7
Jingwen Wu,Xueling Xiao,Xinghai Wang,Wenjie Zhang,Yiruo He,Jiangyue Wang,Xianglong Han,Ding Bai,Ye Tian
A bilayer GelMA/CSMA Janus membrane was fabricated via sequential photo-crosslinking. • CSMA incorporation enhanced mechanical strength, reduced swelling, and slowed degradation. • The membrane showed superior cytocompatibility and osteoinductive potential in vitro . • In rat calvarial defects, it outperformed Bio-Gide® with 1.5-fold higher bone volume. • This integrated membrane is a promising candidate for guided bone regeneration. Alveolar bone regeneration remains a significant clinical challenge, largely because conventional guided bone regeneration (GBR) membranes lack the ability to provide robust, integrated mechanical support and potent osteogenic bioactivity. To address these limitations, we designed a bilayer Janus membrane (G5CS1-G10). It comprises a dense, photo-crosslinked gelatin methacryloyl (GelMA) layer for mechanical support and a porous composite layer of GelMA with methacrylated chitosan (CSMA) for osteogenesis. In a rat calvarial defect model, the G5CS1-G10 membrane significantly outperformed the commercial membrane Bio-Gide®, achieving a 1.5-fold increase in bone volume (BV/TV) and improved osseointegration. Our study demonstrates that this dual functional membrane successfully integrates barrier capacity with osteogenic promotion, offering a promising strategy for advanced maxillofacial bone regeneration.
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2023
·
IF 8.2
Yufan Huang,Jiaofen Lin,Bihua Shen,Chenmin Zheng,Bingqing Huang,Jinmei Zou,Guoguang Zhang,Peng Fei
In this study, chlorogenic acid-chitosan (CA-CS) copolymers were prepared with varying Chitosan (CS): chlorogenic acid (CA)ratios and characterized for their water solubility, antioxidant capacity, and emulsions stability. Results showed that CA-CS samples exhibited up to 90.5 % increase in DPPH scavenging efficiency and 20 % increase in hydroxyl radical scavenging efficiency compared to CS alone. CA-CS copolymers used to stabilize oil in water (O/W) emulsions, which were evaluated for their potential in encapsulating and protecting β-carotene. Microscopic observations revealed homogeneous spherical droplets in stable emulsions, suggesting effective interfacial structures. The selected CA-CS-stabilized O/W emulsions demonstrated encapsulation efficiencies of 74.8 % and 75.26 % for β-carotene. The CA-CS stabilized O/W emulsions provided the most effective protection against β-carotene degradation under UV exposure, retaining over 80 % of β-carotene content after 12 h of testing. These findings indicate that CA-CS-based O/W emulsions show promise as carriers and protectors for bioactive compounds, due to their improved antioxidant capacity, emulsions stability, and protection against degradation.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2023
·
IF 8.2
Jianmin Yang,Fengying Cai,Yicheng Lv,Ting Jiang,Xingkai Zhao,Xueli Hu,Yunquan Zheng,Xianai Shi
Acute bleeding following accidental injury is a leading cause of mortality. However, conventional hemostatic bandages impede wound healing by inducing excessive blood loss, dehydration, and adherence to granulation tissue. Strategies such as incorporating active hemostatic agents and implementing chemical modifications can augment the properties of these bandages. Nevertheless, the presence of remote thrombosis and initiators may pose risks to human health. Here, a hemostatic bandage was developed by physically combined chitosan nonwoven fabric, calcium alginate sponge, and adenosine diphosphate. The presented hemostatic bandage not only exhibits active and passive mechanisms for promoting clotting but also demonstrates excellent mechanical properties, breathability, ease of removal without causing damage to the wound bed or surrounding tissues, as well as maintaining an optimal moist environment conducive to wound healing. In vitro evaluation results indicated that the hemostatic bandage possesses favorable cytocompatibility with low levels of hemolysis. Furthermore, it effectively aggregates various blood cells while activating platelets synergistically to promote both extrinsic and intrinsic coagulation pathways. In an in vivo rat model study involving liver laceration and femoral artery injury scenarios, our developed hemostatic bandage demonstrated rapid clot formation capabilities along with reduced blood loss compared to commercially available fabrics.
✓ 已验证
产品关联
DOI
PubMed
高影响因子