CARBOHYDRATE POLYMERS
·
2021
·
IF 9.381
Huiqiang Wang,Zheng Li,Miao Zuo,Xianhai Zeng,Xing Tang,Yong Sun,Lu Lin
Conductive hydrogels have the mechanical properties and the electronic transport properties of conductive polymers, which have been widely used in the fields of energy storage and bioelectronics. However, the rigidity and brittleness of conductive polymers hinder the long-term stability of hydrogels and limit its application in new flexible electronic devices. It is a high challenging task to prepare ion-conductive hydrogels with excellent mechanical properties, anti-freeze and electrical conductivity through a simple preparation process under the action of hydrogen bonds . We present a facile strategy to prepare mechanically tough, swelling ability hydrogels reinforced by cellulose nanocrystals (CNCs). Herein, CNCs were produced by high pressure homogeneous and pretreated with deep eutectic solvent (DES). The conductivity of the hydrogel is 0.021 S/cm at room temperature . Due to the function of DMSO/H 2 O in organic solvent system, the ion-conducting hydrogel remains flexible and conductive (0.014 S/cm) at −70 °C. Hydrogel has excellent mechanical properties (stress about 1.4 MPa, strain about 1018%), excellent transparency, freezing resistance (−70 °C) and other comprehensive characteristics. The hydrogel can be assembled into a sensor for use in monitoring large and small movements of the human body, showing good responsiveness and stability.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2021
·
IF 3.764
Xinyan Yang,Yunmei Wei,Yinhua Jiang,Yunyun Wang,Li Chen,Long Peng,Shen Zhang,Yan Yan,Yongsheng Yan
Removing excess phosphate from environmental water is extremely important to reduce eutrophication. In this study, cellulose nanocrystals (CNCs) were utilized as biological templates, and the SA-La-X was synthesized by calcination with lanthanum modification. Some characterization techniques were used to confirm the impregnation of La on the surface of mesoporous silica aerogel (SA). The obtained aerogels SA-La-5, 10, and 25 had large specific surface areas (262.69, 251.23, and 197.18 m2 g–1), and average pore sizes of aerogels SA-La-5, 10, and 25 were 5.14, 4.85, and 4.71 nm, respectively. The results manifested that sample SA-La-5 with the molar ratio of Si/La of 5:1 presented the maximum adsorption capacity of 42.08 mg g–1. Meanwhile, SA-La-X exhibited less La leaching, good stability, and strong selectivity for phosphate. Through the adsorption isotherm, the phosphate adsorption over SA-La-X samples followed the Langmuir model, and the kinetic experiment demonstrated that the adsorption process fitted the pseudo-second-order models. The phosphate adsorption mechanism of SA-La-X was detected by X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and X-ray diffraction (XRD), and it was found that the binding mechanism of the adsorbent and phosphorus included electrostatic adsorption, surface precipitation, and ligand exchange. Among them, electrostatic and ligand exchange were considered to be the main ways to selectively adsorb phosphate at pH 3.0. At the same time, the prepared SA-La-X with a cylindrical shape was easy to separate without causing secondary pollution to the water system, which would be the promising adsorbent for phosphate adsorption in the water environment to reduce eutrophication.
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2021
·
IF 6.953
Enmin Zong,Chen Wang,Jiayao Yang,Hangxuan Zhu,Shengtao Jiang,Xiaohuan Liu,Pingan Song
The design of environmentally benign bio-adsorbents for the removal of phosphate from aqueous medium was an economic and effective way for controlling eutrophication . Herein, we prepared three kinds of TiO 2 /cellulose (CE-Ti) nanocomposites by a facile hydrolysis-precipitation method, and used them as antibacterial bio-adsorbents for the removal of phosphate from aqueous medium. Multiple techniques including Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) and thermogravimetric analysis (TGA) were employed to characterize the nanostructure and characteristics of the prepared CE-Ti nanocomposite. The adsorption capacity of the CE-Ti was 19.57 mg P g −1 according to the Langmuir model, which was 6 times higher than that of CE. Importantly, the bacterial inhibition zone of the CE-Ti was 2.88 mm (that of CE was 0 mm), indicating that CE-Ti had good antibacterial activity that could reduce the attachment of the microorganism to the surface of CE-Ti, which was suitable for long-term phosphate removal. Moreover, the CE-Ti had good adsorption selectivity and anti-interference capability, according to interfering ions and ion strength experiments. Furthermore, Ti 4+ leakage tests suggested that CE-Ti was highly stable under acidic, neutral and alkali conditions. These results indicated that the CE-Ti nanocomposite could be utilized as a promising antibacterial bio-adsorbent for effective phosphate removal from aqueous medium.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2021
·Vol. 138
·期 30
·50738
·
IF 3.125
Pengcheng Xu,Dalun Zhang,Ziqiang Shao,Dejia Chen
Lithium-ion batteries (LIBs) are one of the most widely used technologies for various applications. However, polyolefin separators can hardly meet the needs of the development of LIBs due to the poor heat shrinkage and bad wettability with the electrolyte. Herein, a cellulose acetate (CA)-based separator is developed by blending with cellulose nanocrystals (CNCs) using a simple reversible acetylation process. This separator exhibits inherent thermal stability and improved ionic conductivity due to the finger-like and sponge-like porous structure. Moreover, the discharge capacity of the separator with a CNC loading of 3% remains at 132.9 mA h g −1 when the rate reverts to 0.2 C and the capacity retention reaches 89.5% after 50 cycles. Therefore, the obtained CA-based separators can be a competitive candidate for high-performance LIBs and point the way to sustainable development.
✓ 已验证
产品关联
DOI
高影响因子
CARBOHYDRATE POLYMERS
·
2021
·
IF 9.381
Sufeng Zhang,Chen Hua,Bin He,Pengbing Chang,Min Du,Ye Liu
Flexible electronics products have attracted wide attention because of their excellent flexibility, conductivity and stability. In this study, the liquid phase reduction method was used to in situ reduce fractal-structured silver particles (FSSPs) on cellulose surface to prepare conductive paper with excellent conductivity, and good stability and flexibility. The experimental results show that when the mass ratio of silver to cellulose was 1.5:1, the sheet resistance of conductive paper is as low as 0.02 Ω·sq −1 , and the conductivity reaches 1041.33 S cm −1 , which shows excellent conductivity. In order to expand the application of conductive paper in the field of flexible wearable electronic products, the mechanical stability and oxidation resistance of conductive paper were tested. The results show that the conductive paper has good stability and is expected to replace the flexible electronics products made of plastic.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ADVANCED POWDER TECHNOLOGY
·
2021
·
IF 4.833
Yang Huang,Xinyi Li,Xiao Xu,Feng Wei,Ying Wang,Mengtao Ma,Yu Wang,Dongping Sun
An extremely facile and up-scalable approach has been proposed to disperse ferric grains onto bacterial cellulose (BC) nanofibers. The BC-induced hydrolytic deposition can be performed at room temperature without using any organic solvents, toxic reagents, or complicated apparatuses, enabling a green pathway in realizing industrialization. After carbonization, the randomly oriented carbonized BC (CBC) nanofibers transmit the electrons throughout the electrode, while the inherited reticular morphology boosts the thorough penetration of electrolyte. Moreover, the sufficient space created by interconnected CBC nanofibers is able to accommodate the volume change of the nanosized Fe 3 O 4 active materials during repeated Li + intercalation and deintercalation. As a result, the as-prepared Fe 3 O 4 /CBC composites deliver the superior electrochemical performance as the free-standing anodes in Li-ion batteries (LIBs), including the impressive reversible capacity of 702 mAh g −1 after 400 cycles at 400 mA g −1 , decent rate capability with capacity of 437 mAh g −1 at 2000 mA g −1 , and a long cycling lifespan up to 1000 cycles at 800 mA g −1 . This work provides a scalable and green approach to fabricate high-performance LIBs anode with the natural sustainable biomass.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2021
·
IF 13.273
En Li,Yamin Pan,Chunfeng Wang,Chuntai Liu,Changyu Shen,Caofeng Pan,Xianhu Liu
Cellulose-based materials have attracted tremendous interest recently due to their fascinating merits of renewability, biodegradability, and low cost, holding great promise in electromagnetic protection, clean energy harvesting, and thermal management. However, the simple and effective integration of multiple functions into single cellulose material remains a challenge. Herein, we report the fabrication of a multifunctional and superhydrophobic cellulose composite paper (CCP) via coated MXene modified by in-situ polymerized polypyrrole and PDMS/candle soot on the opposite surface of the paper. CCP exhibits high-performance electromagnetic interference shielding effectiveness (~40 dB) while maintaining high electrical conductivity (1467 S/m). Moreover, the superhydrophobic surface of CCP can be used as the hydraulic triboelectric nanogenerator (H-TENG) to harvest water energy due to the liquid–solid contact triboelectrification and electrostatic induction. The hydraulic triboelectric energy can be captured and released when water droplets drop from a height of 2 cm and roll at a tilt angle of 20°, the output current can reach a peak of 0.8 nA. Furthermore, the surface saturation temperature of CCP can reach 140 °C with a low applied voltage of 6 V enabled by the Joule effect. Thus, CCP holds great potentials in applications of integrated smart electronics, clean energy harvesting, and thermal management.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2021
·Vol. 138
·期 42
·51226
·
IF 3.125
Yifan Liu,Ruihan Pei,Yuancai Lv,Chunxiang Lin,Jianhui Huang,Minghua Liu
Due to the low concentration of silver in water, most of the cellulose adsorbents exhibited low removal efficiency, which greatly limited their practical applications. Herein, a cellulose aerogel modified by thiosemicarbamide (CAT) was fabricated for reducing and adsorbing silver ions from low concentration wastewater. The characterization results concluded that CAT owned a three-dimensional spongy structure with many circular microspheres and a better specific surface area (19.37 m 2 g −1 ), as well as the functional groups of ─C═N + ─H and ─(C═S)─N. The static batch adsorption experiments demonstrated that CAT could reached the maximum removal percentage of 94.94% and adsorption capacity of 42.12 mg g −1 under the initial concentration of Ag(I) was 15 mg L −1 and the pH value was 7. Meanwhile, the adsorption of Ag(I) on CAT was second-order reaction, and the Langmuir model could better fit the adsorption process. In addition, CAT exhibited wide pH values (1–9) adaptability and excellent adsorption performance for silver through electrostatic interaction, chelation, and reduction. This study probably provides a new method as well as important experimental data and theoretical reference for the removal of silver ions and other metals.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF HAZARDOUS MATERIALS
·
2021
·
IF 10.588
Mei Hong,Die Li,Bingyu Wang,Jingyu Zhang,Bin Peng,Xiaoling Xu,Yan Wang,Chunyang Bao,Jing Chen,Qiang Zhang
Excess boron in water could result in a critical hazard to plants and humans. Traditional treatment approaches cannot efficiently remove boron from water, especially during seawater desalination using reverse osmosis technology . Achieving satisfactory adsorption capacity and rate for boron remains an unmet goal for decades. Herein, we report cellulose-derived polyols as high-performance adsorbents that can rapidly remove boron and organic pollutants from water. Cellulose-derived polyols were synthesized from saccharides and cellulose via controlled radical polymerization and click reaction. Remarkably, CA@NMDG can adsorb boron with an astonishing capacity of ~34 mg g -1 in 10 min, which surpasses all those cellulose-based materials reported thus far, meanwhile, much faster than those of commercial adsorption resin. Moreover, cellulose-derived polyols also showed high removal efficiencies (70–98% in several minutes) toward certain organic pollutants, including Congo red and Reactive Blue 19. The water-insoluble characteristic of cellulose-derived polyols is advantageous to be separated from the treated sewage after adsorption for reuse. This work provides a novel insight into the fabrication of safe, fast, and high-capacity cellulose adsorbents for water purification .
✓ 已验证
产品关联
DOI
PubMed
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2021
·
IF 6.953
Chuanwei Lu,Chunpeng Wang,Daihui Zhang,Jifu Wang,Qiang Yong,Fuxiang Chu
To develop the hydrogels with high mechanical strength and excellent conductivity is always a challenging topic. In this study, the ultra-strong hydroxypropyl cellulose (HPC)/polyvinyl alcohol (PVA) composite hydrogels were prepared by combination of the triple-network and mechanical training. The proposed composite hydrogels were achieved by physically crosslinking HPC with PVA to form the first crosslinking network, in which the HPC fibers could decrease the crosslinking density of PVA matrix and generate a lot of water-rich porous area. Then, 2-hydroxyethyl acrylate (HEA), acrylamide (AM) and aluminium chloride diffused into the first network to fabricate the chemical crosslinking network and ionically cross-linked domains. The formation of triple-network enhanced the mechanical strength and toughness to 1.87 MPa and 339.09 kJ/m 3 , respectively. Especially, the crystalline domains of PVA chains could improve the hydrogel's fatigue resistance, and the orderly arrangement of the crystalline domains achieved through mechanical training process could further enhance the mechanical strength. The mechanical strength of pre-stretched composite hydrogel was increased up to 2.8 MPa. The composite hydrogels exhibit great applications in sensors, human–machine interactions, and wearable devices.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
FUEL
·
2021
·
IF 6.609
Zhuqian Xiao,Wenwen Zhao,Xingyi Wu,Chuang Xing,Jianbing Ji,Jianwei Mao
The metal immobilizing micro-circumstance is intensively relevant to its catalytic activity and selectivity. In order to obtain C 3,4 ketols by protection of C = O bonds against further hydrogenation, we proposed a promising strategy to modify adjacent circumstance for nickel complexes carbide catalysts (CCCs). The Sn promoted nickel CCCs exhibited high selectivity for cellulose conversion to C 3,4 ketols with the yield of 54.8%. The characterization results demonstrated the coordination environment of metals were reconstructed by C x N y species to form isolated nickel sites. The size-dependent electron transfer occurred when the sizes changed (from cluster to nanoparticles). This electron transfer facilitated promotion of the selectivity for C 3,4 ketols by protection of C O bonds against further hydrogenation. Combined with density functional theory calculations, the size-dependent electron transfer and Lewis base forming mechanism in Ni@C x N y structure were revealed. C x N y phases changed the electronic abundance of Ni sites and subsequently acted as Lewis base. Our work hinted that size of metallic catalysts should be optimized in specific loading circumstance to maximize the catalytic selectivity rather than simply chasing atomic efficiency.
✓ 已验证
产品关联
DOI
高影响因子
COMPOSITES SCIENCE AND TECHNOLOGY
·
2021
·
IF 8.528
Jiayao Yang,Hengxu Wang,Xiaohuan Liu,Shenyuan Fu,Pingan Song
The intrinsic brittleness has significantly restricted practical applications of epoxy resins. Existing toughening strategies often lead to degraded mechanical strength . Hence, it has been attractive but a huge challenge to design high-performance sustainable additives that can simultaneously improve strength and toughness of epoxy resins. Here, we report the synthesis of a nano-TiO 2 /regenerate cellulose (RC) biohybrid via a facile microwave method for strengthening and toughening a soft epoxy resin system (modulus below 1 GPa). Our results show that with 10 phr nano-TiO 2 /RC, the resultant epoxy composite exhibits simultaneous enhancements in tensile strength and impact toughness , ca. 38% and 40% higher than corresponding values of virgin epoxy resin because of improved interfacial compatibility. Moreover, the addition of as-designed nano-TiO 2 /RC can enhance thermostability of epoxy resin. It has a slightly negative effect on the curing reaction but does not change the curing mechanism of epoxy resins. This study provides a facile, efficient and green method for preparing bifunctional additive for creating strong and tough epoxy composites, which are expected to find wider applications in industries.
✓ 已验证
产品关联
DOI
高影响因子