JOURNAL OF ELECTRONIC MATERIALS
·
2025
·Vol. 54
·期 8
·6300-6314
·
IF 2.5
Wang Longqin,Li Gang,Jiang Yunshan,Ma Haiguo,Deng Shukang,Deng Shuping
Here, we report that a combination of vacuum melting and spark plasma sintering efficiently enhances the thermoelectric properties of the PbTe-PbSe compounds. Thermal analysis results show that all the PbTe 1− x Se x samples have excellent thermal stability. Positron annihilation spectroscopy results indicate improvement of the crystal quality in all obtained PbTe 1− x Se x samples. X-ray photoelectron spectroscopy studies revealed the presence of Pb 2+ , Pb 4+ , Te 2− , Te 4+ , Se 2− states of Pb, Te, and Se. Meanwhile, replacing the isoelectronic cations with those of different electronegativity will lead to a variation in carrier concentration. All samples exhibit p -type conduction with carrier concentrations varying from 0.07 × 10 19 to 7.34 × 10 19 cm −3 , since carrier mobility changes from 4.7 to 727.7 cm 2 V −1 s −1 at room temperature. Therefore, the maximum figure of merit ( ZT ) value reaches 0.6 at 773 K for the PbSe 0.95 Te 0.05 sample benefiting from the greatly reduced thermal conductivity, which is three times more than the intrinsic PbSe. The peak ZT value of 0.70 at 773 K is obtained in PbTe 0.98 Se 0.02 due to the excellent power factor. Valuable insight can be obtained from a quantitative analysis of the thermoelectric transport in PbTe-PbSe compounds with the anion vacancies (Se 2− and Te 2− ). Graphical
✓ 已验证
产品关联
DOI
高影响因子
Frontiers of Chemical Science and Engineering
·
2012
·Vol. 6
·期 3
·339-347
·
IF 0
Zhou Dongjiao,Shen Shaochuan,Yun Junxian,Yao Kejian,Lin Dong-Qiang
Dextran-hyaluronate (Dex-HA) based supermacroporous cryogel scaffolds for soft tissue engineering were prepared by free radical cryo-copolymerization of aqueous solutions containing the dextran methacrylate (Dex-MA) and hyaluronate methacrylate (HA-MA) at various macromonomer concentrations under the freezing condition. It was observed that the suitable total concentration of macromonomers for the preparation of Dex-HA cryogel scaffold with satisfied properties was 5% (w/w) at the HA-MA concentration of 1% (w/v), which was then used to produce the test scaffold. The obtained cryogel scaffold with 5% (w/w) macromonomer solution had high water permeability (5.1 × 10 −12 m 2 ) and high porosity (92.4%). The pore diameter examined by scanning electron microscopy (SEM) was in a broad range of 50–135 μm with the mean pore diameter of 91 μm. Furthermore, the cryogel scaffold also had good elastic nature with the elastic modulus of 17.47±1.44 kPa. The culture of 3T3-L1 preadipocyte within the scaffold was investigated and observed by SEM. Cells clustered on the pore walls and grew inside the scaffold indicating the Dex-HA cryogel scaffold could be a promising porous biomaterial for applications in tissue engineering.
✓ 已验证
DOI
JOURNAL OF POROUS MATERIALS
·
2020
·Vol. 27
·期 5
·1455-1466
·
IF 2.183
Yuan Zhishuai,Cheng Yuchun,Ma Shoutao,Jiang Zhen,Zhou Yisi,Wang Yingjun,Zhang Wei,Suo Yanhua
A new method called Instant Exactness Synthesis (IES), which was applied to prepare SAPO-11 molecular sieve, was introduced innovatively. The metal–acid bifunctional Ni/SAPO-11-IES catalyst with a Ni content of 4% was prepared by the impregnation method. Ni/SAPO-11-H catalyst was prepared as a comparative sample through the traditional hydrothermal method. In addition, the growth mechanism was used to explain the excellent performance of catalyst prepared by IES method in detail. The structure of Ni/SAPO-11-IES was confirmed via XRD and TEM characterization. The pore structure of the molecular sieve was determined by nitrogen adsorption and desorption. 29 Si MAS NMR measurement was used to illustrate multiple silicon environment which supported the excellent acidity in NH 3 -TPD measurement. Furthermore, the favourable dispersibility of Ni species was proved by the mapping of the elements and EDS. Benefiting from the superior performance of materials, Ni/SAPO-11-IES catalyst exhibited a higher catalytic performance for n-heptane hydroisomerization with n-heptane conversion of 82% and isoheptane selectivity of 86%, respectively, compared with other catalysts in the same system. The study also provides new ideas for the preparation of molecular sieve materials.
✓ 已验证
DOI
高影响因子
Nature Communications
·
2026
·
IF 18.1
Wang Shengnan,Gao Yao,Wang Shixun,Ai Mingzhong,Guo Yihui,Liu Xingjun,Wang Yiqiao,Wei Zhiquan,Zhu Jiaxiong,Nian Qingshun,Zhang Cuili,Wang Lang,Lu Shengbo,Liu Tracy Chenmin,Li Quan,Zhi Chunyi
Zinc-based flow batteries are gaining attention as safe, cost-effective, and sustainable energy storage solutions amid global energy transition challenges. However, their practical application is hindered by poor reversibility and dendrite formation of Zn negative electrode, particularly under high state-of-charge conditions. Despite extensive research on Zn side, the relationship between localized temperature distribution and dendrites remains underexplored, primarily due to limited microscopic observation techniques. Here, we present a non-invasive optically detected magnetic resonance with nanodiamond quantum sensors to monitor temperature variations during Zn deposition, achieving a sub-micron spatial resolution ( ~ 300 nm) and a temperature sensitivity of ~2 K/Hz 0.5 . Our findings suggest that spatial temperature non-uniformity may play a critical role in accelerating dendrite growth and potentially leading to more severe short circuits. Simulations revealed that higher substrate thermal conductivity improves Zn deposition uniformity. Herein, we introduced a flowable gallium-indium liquid metal electrode, which disperses localized heat and lowers interfacial temperature gradients, thereby suppressing hotspot-driven dendrite growth and enabling in situ formation of a liquid Zn alloy. The zinc-bromine flow battery with the liquid metal electrode demonstrated enhanced cycling stability over 2400 hours at a high state-of-charge of 90%, achieving a cumulative discharge capacity of 46.2 Ah cm −2 at 40 mA cm −2 .
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Nature Communications
·
2026
·
IF 18.1
Wang Xu,Kallenbach Cynthia M.,Almaraz Maya,Georgiou Katerina,Sun Lifei,Sang Changpeng,Jiang Ping,Liu Yue,Bai Edith,Wang Chao
Microbial necromass is increasingly recognized as a major source of stable soil organic matter (SOM), and its persistence is often attributed to interactions with clay-sized minerals. However, the mechanisms underlying this mineral-mediated stabilization remain poorly understood. Here, we conducted an in situ dual-labeled ( 13 C and 15 N) microbial necromass experiment across a clay gradient to quantify how clay content and necromass origin (bacterial vs. fungal) regulate necromass persistence. We find that higher clay content markedly enhances necromass retention by strengthening mineral protection, suppressing microbial activity and diversity, and limiting leaching losses. NanoSIMS imaging shows that new necromass preferentially associates with organic matter coatings on the rough mineral surfaces, highlighting organo-organic interfaces as important stabilization pathways. Necromass origin exerts little effect on retention despite marked differences in C:N ratios and bulk chemical composition, indicating that finer-scale molecular features, rather than broad compositional differences, govern necromass stabilization in soils.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Nature Communications
·
2026
·
IF 18.1
Zhao Xin,Li Jian,Xiao Shaoliang
As one of the core advanced manufacturing technologies, additive manufacturing is of high application value in the aerospace, biomedical, and industrial component manufacturing fields. Nevertheless, current additive manufacturing materials (e.g., petroleum-based resins) face limitations such as poor stability, limited shape recovery, and insufficient mechanical properties, which restrict sustainable manufacturing progress. Inspired by the stress-dissipation mechanism in plant cell walls, we develop a cellulose-based photopolymerizable resin that delivers exceptional stiffness-deformability synergy and spatiotemporally shape memory capability. These structures integrate excellent mechanical strength and rapid recovery performance after deformation. The additive manufacturing cellulose-based photopolymerizable resin material exhibits a synergistic stiffness-deformability profile, achieving a compressive strength of 115.42 MPa and stiffness of 1404.16 MPa. These characteristics lay the foundation for specialized defense components, energy absorption systems, and spatiotemporal memory materials.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
IONICS
·
2026
·
IF 3.4
Guan Zhirong,Zhang Yudong,Sun Hui,Yu Jian,Li Lin,Zhou Tong,Zhang Xuejing,Huang Saifang
Ni-rich cathode materials are highly promising for high-performance lithium-ion batteries, owing to their superior overall electrochemical properties. The electrochemical performance of these materials is intimately linked to the degree of ordered development within their layered structure. However, the optimal lithiation calcination temperature for achieving highly ordered layered structures varies among Ni-rich materials with different nickel contents, and this critical parameter has not been thoroughly investigated. This study systematically addresses this gap by selecting four precursors with distinct nickel contents and subjecting them to lithiation calcination across a series of stepwise temperatures. Through in-situ high-temperature X-ray diffraction (XRD) and XRD Rietveld refinement, we deciphered the dynamic evolution characteristics of layered structures during lithiation in materials with varying nickel contents. Furthermore, we clarified the regulatory effect of lithiation temperature on the materials’ structural order and concurrently evaluated their electrochemical performance. Ultimately, this research clarifies the intrinsic relationship between lithiation temperature, layered structure characteristics, and electrochemical performance, offering significant guidance for the precise design and preparation of high-performance Ni-rich cathode materials.
✓ 已验证
产品关联
DOI
高影响因子
ANALYTICAL AND BIOANALYTICAL CHEMISTRY
·
2026
·
IF 4.1
Ding Zhengyuan,Zhu Linlian,Zhou Yaqiu,Li Mengwei,Yao Yi,Su Mengjie,Wu Zengqiang,Wang Li,Yu Chunmei
In this study, we presented the design and development of a flexible and non-enzymatic electrochemical sensor based on in situ growth of Au nanowires (AuNWs) on carbon cloth (CC) for the dynamic monitoring of uric acid levels in human sweat. The electrode was fabricated through a controllable process, resulting in a three-dimensional conductive network with high surface area and abundant electroactive sites on the electrode surface. Electrochemical analyses demonstrated that the electrode exhibits excellent sensitivity toward uric acid with a wide linear response range from 10 to 700 μM and a low detection limit of 1.4 μM. The electrode was further integrated into a wearable sensing platform and applied for real-time, non-invasive sweat sampling and monitoring during exercise. The results indicated that the sensor exhibited a high correlation between sweat and blood uric acid levels measured by a commercial device, validating its potential applicability for the daily monitoring of uric acid. This work provides a promising strategy for the development of facile and reliable wearable sensors, with significant potential in non-invasive healthcare monitoring. Graphical abstract
A flexible and wearable sensor by in situ growth of Au nanowires on carbon cloth was developed for the real-time and non-invasive monitoring of uric acid metabolite in sweat.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Nature Communications
·
2026
·Vol. 17
·期 1
·1909
·
IF 15.7
Yang Bin,Li Deyang,Deng Renren,Zhao Jian,Wang Yubin,Xu Shiqing,Lei Lei
Persistent luminescence materials are promising for night-vision displays, background-free medical diagnostics, and high-resolution radiography, yet achieving efficient violet, yellow, and red emission within a single robust and scalable host remains a longstanding challenging. Here, we overcame this limitation by constructing Gd 3+ -mediated cluster traps within alkaline-earth fluorochlorides to minimize energy loss during electron migration. These clusters serve as both intrinsic emitters and efficient energy transfer platforms for various activators, including Eu 2+ , Sm 2+ , Tb 3+ , and Mn 2+ , enabling bright and spectrally tunable multicolor persistent luminescence upon X-ray irradiation. The persistent luminescence intensity of Eu 2+ is enhanced by up to 32.7-fold upon Gd 3+ codoping. Moreover, violet persistent luminescence from Eu 2+ is employed to excite perovskite quantum dots for full-color time-domain dynamic displays, while Sm 2+ emission facilitates low-dose, high-resolution delayed X-ray imaging. These findings establish a generalizable strategy for designing efficient multicolor persistent materials for advanced multifunctional optical technologies.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
PHARMACEUTICAL RESEARCH
·
2026
·
IF 4.1
Jiang Qi,Qiu Yihe,Li Peirong,Yu Caini,Meng Tingting,Hu Fuqiang,Wang Cheng,Yuan Hong
Objective Cancer remains a critical public health challenge. Conventional anti-tumor drugs are often limited by their short half-life and the requirement for frequent and/or high-dose administration, highlighting the urgent need for drug delivery systems that can enhance intracellular drug accumulation. Methods Given that current research on drug delivery systems primarily focuses on developing active or passive targeting strategies to improve therapeutic efficacy, biocompatible cholesterol-based lipid nanoparticles (Cls-LNPs) were developed in this study. The Cls-LNPs were designed to function as an "intracellular drug reservoir" by enhancing cellular uptake and retention, thereby meeting the core requirement of enhanced intracellular drug accumulation. Results The reservoir capacity is likely attributed to the ability of Cls-LNPs to evade lysosomal degradation and target the endoplasmic reticulum (ER). When combined with the emerging anti-tumor technology of photodynamic therapy (PDT) and utilizing Ce6 as a model photosensitizer, the prepared Ce6@Cls-LNPs exhibited enhanced anti-tumor efficacy both in vitro and in vivo compared to free drugs. The therapeutic effect was achieved through the induction of ER stress, lipid peroxidation, and apoptosis, and it also exhibited a “bystander effect”. Conclusion This study offers valuable insights into the application of cholesterol in drug delivery systems and proposes innovative strategies for the development of retention-enhancing formulations. Graphical
✓ 已验证
产品关联
DOI
PubMed
高影响因子
International Journal of Oral Science
·
2026
·Vol. 18
·期 1
·6
·
IF 17.6
Guo Jiajie,Qiu Qiujing,Yan Xiaoyuan,Zhang Zeying,Zhang Xiyue,An Na,Yin Chengcheng,Yang Di,Okamura Hirohiko,Yoshida Kaya,Sun Hongchen,Qiu Lihong
Rheumatoid arthritis (RA) is an autoimmune disorder that triggers progressive joint destruction by inducing excessive osteoclastogenesis. Porphyromonas gingivalis ( Pg ), the main pathogenic bacterium involved in periodontitis (PD), is closely related to RA. Pg can secrete extracellular vesicles (EVs), which carry numerous virulence factors. The aim of this study was to investigate whether Pg- derived EVs can be transported and exacerbate bone destruction in RA by promoting osteoclastogenesis and to elucidate the underlying mechanisms involved. EVs derived from Porphyromonas endodontalis ( Pe ), which is weakly associated with PD or RA, were used as controls. Pg and Pe EVs interact with osteoclasts after translocating into the marrow and metacarpal joints of mice. In vitro, Pg EVs induce osteoclastogenesis via various components, such as lipopolysaccharide, proteins, lipoproteins, and proteases. TNF-α, IL-1β, and IL-6 promote but cannot independently control Pg EV-induced osteoclastogenesis. RNA sequencing and verification experiments further demonstrated that Pg EVs induced osteoclastogenesis by promoting the phosphorylation of spleen tyrosine kinase (Syk). In vivo, Pg EVs exacerbated RA-induced bone destruction by activating Syk-dependent osteoclastogenesis. R406, a Syk inhibitor, significantly attenuated Pg EV-induced RA osteoclastogenesis and bone destruction. However, Pe- derived EVs presented an extremely weak ability to promote osteoclastogenesis and RA. Our findings reveal a new mechanism by which Pg EVs can exacerbate RA via transport through the circulation and the promote Syk-dependent osteoclastogenesis. This study deepens our understanding of the significant pathogenic role of EVs derived from oral bacterial in RA and explores targeted therapeutic strategies by inhibiting the activation of Syk.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Nature Communications
·
2026
·
IF 18.1
Yang Ming,Liu Wenliang,Chen Ping,Liu Zhuang,Sun Renyuan,Xu Baochun,Wang Qiong,Xue Bingqing,Gao Chuan,She Jiahui,Ma Chong,Zhang Dingke,Li Zhikun,Yi Nanxi,Zhang Donghui,Feng Jiexiong,Yu Cunjiang,Wang Jie,Luo Zhiqiang
Deep brain stimulation (DBS) is effective for treating neurological and psychiatric disorders. However, its tethered configuration, invasiveness, and limited tissue compatibility motivate wireless, minimally invasive alternatives. Here, we develop an in situ-gelled injectable conductive hydrogel (ICH), enabling wireless neuromodulation via electric-field localization under volume conduction. The ICH forms in vivo through bio-catalyzed polymerization and electrostatic self-assembly, yielding a stable, highly conductive, tissue-soft, and biocompatible network. Under high-frequency capacitive coupling, impedance difference between the ICH and surrounding brain tissue induces interfacial polarization and charge accumulation, locally concentrating the electric field to activate nearby neurons. This mechanism is supported by enhanced calcium signaling, increased c-Fos expression, and electrophysiological evidence of balanced basal ganglia-cortical activity. In a Parkinson’s disease rat model, ICH-mediated stimulation improved locomotor behavior, preserved dopaminergic neurons, and restored functional connectivity and structural integrity as revealed by fMRI. This injectable hydrogel bioelectronics provides a platform for minimally invasive, wireless neuromodulation therapies.
✓ 已验证
DOI
PubMed
高影响因子