Journal of the Taiwan Institute of Chemical Engineers
·
2017
·
IF 4.217
Libin Yang,Zhan Wang,Jinglong Zhang,Peng Song,Liping Liu
A thermally induced phase separation followed by non-solvent induced phase separation (TIPS-co-NIPS) was used to prepare polyethersulfone (PES) substrate with reduced internal concentration polarization (ICP) for thin film composite forward osmosis (TFC-FO) membrane. Using polyethylene glycol (PEG) as the additive, impacts of TIPS process on substrate properties, TFC layers and FO performances were investigated. The results revealed that the substrate prepared by TIPS-co-NIPS method with 10 s cooling time showed a fully finger-like structure, enhanced permeation performance and better surface hydrophilicity. As a result, the corresponding TFC-FO membrane exhibited 44% lower structural parameter than the TFC-FO membrane based on NIPS substrate (684 µm versus 380 µm), high water fluxes up to 32.9/20.4 LMH and reverse salt fluxes of 14.1/8.2 gMH in the PRO/FO mode using 1 M NaCl as the draw against DI-water feed. Therefore, the proposed TIPS-co-NIPS method utilizing PEG as the additive may be considered as a feasible approach to regulate substrate structure and property for TFC-FO membrane.
✓ 已验证
DOI
高影响因子
DALTON TRANSACTIONS
·
2019
·Vol. 48
·期 9
·2977-2987
·
IF 4.052
Hai-Dan Wang,Xing-Fang Wang,Fang Su,Jian-Sheng Li,Lan-Cui Zhang,Xiao-Jing Sang,Zai-Ming Zhu
Carboxyethyltin and first-row transition metals (TMs) were firstly introduced into trivacant Keggin-type tungstoantimonate in an aqueous solution, leading to the formation of four crystalline organic–inorganic hybrid sandwich-type polyoxometalates (POMs), formulated as Na10−x−yKyHx[((TM)(H2O)3)2(Sn(CH2)2COO)2(SbW9O33)2]·nH2O (SbW9-TM-SnR, TM = Mn, Co, Ni, Zn; x = 1, 1, 0, 0; y = 0, 5, 5, 2; n = 18, 24, 24, 22, respectively). SbW9-TM-SnR exhibit high catalytic ability for the oxidation of cyclohexanol. Meanwhile, SbW9-TM-SnR were composited with polypyrrole (PPy) through an electropolymerization process, forming PPy-SbW9-TM-SnR, on which platinum (Pt) was further electro-deposited to prepare PPy-SbW9-TM-SnR/Pt for electrocatalytic methanol (CH3OH) oxidation in acid solution. The composition and morphology of PPy-SbW9-TM-SnR/Pt were determined by IR, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS). The electrochemical experimental results show that SbW9-TM-SnR and PPy obviously enhance the electrocatalytic and anti-intoxication abilities of Pt, and the highest peak current density of 0.87 mA cm−2, corresponding to 1.85 and 1.43 times higher than those of pure Pt and PPy/Pt electrodes respectively, is acquired for the PPy-SbW9-Ni-SnR/Pt composite electrode. These findings may enlarge the application of PPy and POMs in the electrocatalytic field.
✓ 已验证
DOI
高影响因子
DALTON TRANSACTIONS
·
2018
·Vol. 47
·期 48
·17515-17524
·
IF 4.099
Fengjun Chun,Binbin Zhang,Honggang Liu,Wen Deng,Wen Li,Meilin Xie,Chao Luo,Weiqing Yang
A series of Na+ and Pr3+ co-doped orange-emitting CaYAl3O7 (CYAO) phosphors were prepared by a conventional high-temperature solid-state reaction method. The crystalline structure, the luminescence properties and the decay times of the as-prepared samples were systematically investigated by X-ray diffraction (XRD) and steady-state and time-resolved photoluminescence. Under ultraviolet (UV) light and blue light excitation, the CYAO:Pr3+ phosphors exhibited orange photoluminescence emission and show potential for application in warm white LEDs, and the emission spectra of the as-prepared samples in the near-infrared (NIR) region were detected. Furthermore, Na+ ions were designed as charge compensators to maintain the charge balance. The luminescence intensities in the visible and NIR regions can be effectively enhanced by adjusting the doping amounts of Pr3+ ions and Na+ ions. Moreover, the optical spectra of Pr3+ in the CYAO host crystals were calculated by conventional parametric modeling based on the diagonalization of the complete 91 × 91 energy matrix. The calculated optical spectra were in good agreement with the observed ones and the obtained crystal field parameters were also in a reasonable range. This systemic study, and all of the above, will give a deep insight into the luminescence mechanism of the phosphors and then open one way to exploit the new phosphors for white LEDs.
✓ 已验证
DOI
高影响因子
Materials Today Physics
·
2024
·
IF 10
Yuxiang Tang,Yake Yuan,Yuxue Mo,Haotian Tang,Mianze Wei,Haiqing Zhou,Tian Sheng,Chunsheng Li,Yan Sun,Xiaolin Wei
Lithium-sulfur (Li–S) batteries with high theoretical specific capacity of 1675 mAh g −1 and energy density of 2600 Wh kg −1 are considered as a promising candidate for energy conversion and storage devices in future. However, some critical dilemmas such as low real energy density , high solubility of ether-based electrolytes and slow redox kinetics of long-chain polysulfides remain unsettled hindering their development. Here we design and propose a high-performance sulfur host material constructed by growing CoN/Co 9 S 8 nanoparticles enclosed in reduced graphene oxide (RGO) and Co 9 S 8 modified separator to enhance the electrochemical performance of Li–S batteries . The results of first principal calculations confirm that the calculated adsorption energies of Li 2 S 8 , Li 2 S 6 , Li 2 S 4 and Li 2 S 2 on the Co 9 S 8 (111) surface are lower than that of the CoN (111) surface, indicating that the Co 9 S 8 has stronger adsorbing effect with polysulfides . Furthermore, the catalytic effect in Li 2 S 6 symmetric batteries and the nucleation of the Li 2 S tests display that the CoN/Co 9 S 8 @RGO has a fast conversion reaction kinetics and catalytic effect of polysulfides , thereby inhibiting the leakage of the polysulfides. Consequently, the S@CoN/Co 9 S 8 @RGO cathode with Co 9 S 8 layer represents a high discharge capacity of 1367.7 mAh g −1 at 0.1C and a prolonged lifespan over 700 cycles at 1 C with an extremely low decay rate of 0.06 % per cycle and high cycling stability.
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2020
·
IF 4.65
Lingjun Li,Lingfeng Xia,Huiping Yang,Xuehui Zhan,Jie Chen,Zhaoyong Chen,Junfei Duan
The high voltage application of the LiNi 0.5 Co 0.2 Mn 0.3 O 2 cathode is still hindered by its unstable surficial structure and poor capacity retention. Surface coating has been proved to be an effective strategy to deal with these problems. However, previous multistep surface coating approaches greatly complicate the synthesis procedure. In this work, a simple and large-scale solid-state approach is developed to prepare lanthanum-based oxides co-coated LiNi 0.5 Co 0.2 Mn 0.3 O 2 cathode materials . Electrochemical tests indicate that the co-coated samples exhibit superior cycle life and higher rate performance than those of the pristine sample. Further studies reveal that the enhanced interface stability and facilitated electron transportation can be attributed to the synergetic contribution provided by the lanthanum-based oxides co-coating layer. The present work demonstrates that our approach can achieve cathode synthesis and surface coating synchronously, and shows great potential to apply on a large scale and extent to all Ni-rich cathodes.
✓ 已验证
DOI
高影响因子
CHEMICAL PHYSICS LETTERS
·
2013
·
IF 2.145
Yanling Liu,Feng Song,Jiadong Liu,Jun Zhang,Yin Yu,Hongyan Zhao
The enhanced luminescences of Er 3+ /Yb 3+ co-doped Y 2 Ti 2 O 7 films were demonstrated when silver/gold (Ag/Au) nanoparticles (NPs) were doped in the films. With the precipitation of the Ag nanoprisms, more intense green (525 nm, 546 nm), red (659 nm) upconversion (UC) emission bands and strong enhanced near infrared (NIR) emission were observed and the enhanced factors were up to 16.7, 15.6, 17.7 and 5.6 folds, respectively. The accordance between the local surface plasmon resonance of NPs and the UC emission band significantly increased the luminescence intensity. The efficiencies of the radiative emissions were enhanced also due to the hydroxyl groups primarily absorbed around the NPs.
✓ 已验证
DOI
高影响因子
PHYSICAL CHEMISTRY CHEMICAL PHYSICS
·
2015
·Vol. 17
·期 39
·26320-26329
·
IF 4.493
Meilin Lv,Yinghao Xie,Yawei Wang,Xiaoqin Sun,Fangfang Wu,Hongmei Chen,Shuwei Wang,Cai Shen,Zuofeng Chen,Shuang Ni,Gang Liu,Xiaoxiang Xu
Modification of prototype perovskite compound SrTiO3 by introducing foreign elements has been an appealing means to endow this wide band gap semiconductor with visible light responses. Here we systematically investigated a series of Sr1−xBixTi1−xCrxO3 solid solution compounds prepared by two different synthetic routes, namely, solid state reactions and the hydrothermal method. Their crystal structures as well as other physicochemical properties were explored. Our results showed that a number of important factors such as microstructures, crystallinity, light absorbance and surface compositions etc. are all strongly correlated with the synthetic methods used. The hydrothermal method is generally helpful for morphology controls as well as avoiding Cr6+ defects and Sr segregation at the surface, thereby contributing to a high photocatalytic activity. Better performance normally occurs in samples with a high crystallinity and free of defects like Bi5+. Theoretical calculations suggest that Cr plays an important role in band gap reduction and photocatalytic reactions, while Bi only acts as a constituent cation for the perovskite structure and does not significantly alter the electronic structures near the Fermi level. Our findings have revealed how synthetic routes are relevant to the final photocatalytic properties of a compound, and therefore comparisons among various photocatalysts have to include concerns about their preparation history.
✓ 已验证
DOI
高影响因子
OPTICAL MATERIALS
·
2016
·
IF 2.183
Jiantao Zhang,Chaoyang Ma,Zicheng Wen,Miaomiao Du,Jiaqi Long,Ran Ma,Xuanyi Yuan,Junting Li,Yongge Cao
Gamma-AlON: 0.2Eu 2+ , Tb 3+ phosphors were firstly synthesized via a high temperature solid-state reaction. For the phosphors, luminescence properties as well as energy transfer mechanism were investigated in detail. The energy transfer from Eu 2+ to Tb 3+ in the γ-AlON host was ascribed to the dipole-dipole mechanism, and the efficiency and critical distance in the energy transfer process were also estimated. γ-AlON: 0.2Eu 2+ , Tb 3+ phosphors showed a broad-band emission centered at about 405 nm and other several emission peaks, which were assigned to the 5d–4f transition of Eu 2+ ions and the 5 D 4 – 7 F J (J = 6, 5, 4, and 3) characteristic transitions of Tb 3+ ions, respectively. The results indicated that γ-AlON: 0.2Eu 2+ , Tb 3+ phosphors have great potential application in white light-emitting diodes due to its broad-band excitation in the ultraviolet range and the high-efficient green light emission.
✓ 已验证
DOI
高影响因子
JOURNAL OF LUMINESCENCE
·
2020
·
IF 3.28
Zefeng Xu,Yuhan Zhu,Pu Fan,Qi Luo,Zongjie He,Xiaoguang Liu,Ling Li
A novel adjustable dual excited emission Eu 2+ /Eu 3+ co-doped Ca 4 Si 2 O 7 F 2 phosphor are reported. Unlike most of Eu 2+ doped inorganic compounds , in the host lattice Ca 4 Si 2 O 7 F 2 , partial Eu 3+ can still exist stably even in reducing atmosphere. The adjustable dual excited emission from blue light to red light can be found by changing the wavelength of excitation emission or the concentration of europium doped ion. The mechanism by which the two ions Eu 2+ and Eu 3+ can coexist in Ca 4 Si 2 O 7 F 2 is revealed through the bond energy theory. Eu 2+ and Eu 3+ in Ca 4 Si 2 O 7 F 2 system can be demonstrated to occupy the Ca1 lattice of Ca 4 Si 2 O 7 F 2 .
✓ 已验证
DOI
高影响因子
INORGANIC CHEMISTRY COMMUNICATIONS
·
2026
·
IF 5.9
Haochen Zhou,Ting Chen,Qifei Xia,Renjie Zhou,Zhixiang Xie
A dual-shell hierarchical protection strategy combining non-hydrolytic sol-gel derived SnO x coating and mesoporous ZSM-5 encapsulation was proposed to simultaneously boost luminescence efficiency and environmental stability of CsPbBr 3 nanocrystals. • Conformal amorphous SnO x layer uniformly passivates surface defects of CsPbBr 3 , the optimized CsPbBr 3 @SnO x sample achieves a PLQY increase from 64% to 74%, and retains 55% and 47% initial PL intensity after 120 min immersion in water and ethanol, respectively. • Secondary encapsulation within hierarchical micro-mesoporous ZSM-5 further reinforces structural robustness, raising the maximum PLQY of CsPbBr 3 @SnO x @ZSM-5 composite up to 76%. The composite exhibits negligible emission shift after 120 min treatment in water, ethanol and tetrahydrofuran, with outstanding retention of luminescence signal. • White light-emitting diode (WLED) assembled with CsPbBr 3 @SnO x @ZSM-5 green phosphor and commercial red K 2 SiF 6 :Mn 4+ phosphor delivers balanced white emission with CIE coordinates of (0.310, 0.307), a color rendering index of 70, correlated color temperature of 6651 K and luminous efficiency of 26.76 lm W −1 , demonstrating great potential for solid-state lighting applications. All-inorganic CsPbBr 3 perovskite nanocrystals (NCs) exhibit excellent optoelectronic properties but suffer from severe instability against moisture, oxygen, heat, and polar solvents due to their ionic lattice, surface defects, and labile ligands, leading to rapid ion migration and photoluminescence quenching. In this work, a dual-shell engineering strategy based on a non-hydrolytic sol-gel (NHSG) route was developed to construct CsPbBr 3 @SnO x and CsPbBr 3 @SnO x @ZSM-5 composite nanostructures. An SnO x -rich interfacial layer was formed on the CsPbBr 3 NCs and subsequently coupled with hierarchical ZSM-5 confinement, contributing to surface-defect passivation and stabilization of the interfacial chemical environment while preserving the perovskite crystal structure and emissive centers. At an optimized Sn/Pb molar ratio of 0.5, the photoluminescence quantum yield (PLQY) increased from 64% to 74%, and an optimal reaction time of 10 min yielded the highest emission efficiency (PLQY≈70%). Moreover, the SnO x coating significantly enhanced environmental stability, with CsPbBr 3 @SnO x retaining 55% and 47% of its initial PL intensity after 120 min exposure to water and ethanol, respectively. Subsequently, hierarchical encapsulation within mesoporous ZSM-5 further reinforced structural robustness and optical stability. The resulting CsPbBr 3 @SnO x @ZSM-5 composite achieved an enhanced PLQY of 76% and exhibited negligible emission shift after immersion in water, ethanol, and tetrahydrofuran for 120 min. In addition, the composite demonstrated excellent stability under continuous UV irradiation, thermal treatment, and ambient storage conditions. Finally, a white light-emitting diode (WLED) device fabricated using CsPbBr 3 @SnO x @ZSM-5 delivered stable white emission with Commission Internationale de l'Éclairage (CIE) coordinates of (0.310, 0.307), a color rendering index (CRI) of 70, a correlated color temperature (CCT) of 6651 K, and a luminous efficiency of 26.76 lm W −1 . These results highlight the effectiveness of the dual encapsulation strategy in simultaneously enhancing the photoluminescence performance and environmental stability of perovskite nanocrystals, providing a viable route toward high-performance optoelectronic and solid-state lighting applications. Download: Download high-res image (303KB) Download: Download full-size image
✓ 已验证
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2026
·
IF 9.1
Cunxi Yu,Yao Fu,Jiahui Song,Jun Gao,Ximing Hu,Shuifei Li,Zhixiang Xia,Mengxiang Fang
A novel blended amine absorbent was developed for post-combustion CO₂ capture to achieve low energy consumption and high stability. Using N-hydroxyethylpiperazine (HEPZ) as the main component and N , N ′-bis(2-hydroxyethyl)piperazine (BHEP) as the co-component, nine formulations were screened by absorption–regeneration experiments (40 °C absorption with 12 vol% CO₂, 120 °C regeneration). The optimized A-1 blend (45 wt% HEPZ +5 wt% BHEP) showed a cyclic capacity of 2.01 mol/kg, more than twice that of 30 wt% monoethanolamine (MEA), and a regeneration rate of 2.26 × 10 −3 mol/kg/s, 143% higher than MEA. Its thermal degradation remained below 8% after 14 days at ≤120 °C, and its 28-day oxidative degradation was 38%, lower than 47% for MEA. Corrosivity toward S304 stainless steel was significantly lower. In continuous bench-scale tests with a simulated flue gas (12 vol% CO₂ in N₂) under optimal conditions (liquid-to-gas ratio 14 L/m 3 , heating power 35%), the A-1 blend achieved 92% CO₂ capture efficiency with a regeneration energy of 2.64 GJ/tCO₂, 34% lower than that of MEA under the same conditions. The blend also exhibited faster absorption at high CO₂ partial pressure. Under the simplified flue-gas conditions examined, the HEPZ–BHEP blend combines high cyclic capacity, low regeneration energy, acceptable thermal stability within the conventional regeneration temperature range (100–120 °C), and lower oxidative degradation and corrosivity than MEA, suggesting its potential as an alternative to conventional MEA for post-combustion CO₂ capture. Further validation under realistic flue-gas conditions (with O₂, moisture, and SO₂/NOₓ) and long-term operation is required before industrial application. Download: Download high-res image (197KB) Download: Download full-size image
✓ 已验证
DOI
高影响因子
Polymers
·
2020
·Vol. 12
·期 11
·2482
·
IF 3.426
Fei Song,Zhidan Wang,Wenli Gao,Yu Fu,Qingrong Wu,Shouxin Liu
Novel temperature/reduction dual stimulus-responsive triblock copolymers, poly [2-(2-methoxyethoxy) ethyl methacrylate-co-oligo (ethylene glycol) methacrylate]-b-(L-polylactic acid)-SS-b-(L-polylactic acid)-b-poly[2-(2-methoxyethoxy) ethyl methacrylate-co-oligo(ethylene glycol)methacrylate] [P(MEO2MA-co-OEGMA)-b-PLLA-SS-PLLA-b-P(MEO2MA-co-OEGMA)] (SPMO), were synthesized by ring opening polymerization (ROP) of L-lactide and 2,2’-dithio diethanol (SS-DOH), and random copolymerization of MEO2MA and OEGMA monomers via atom transfer radical polymerization (ATRP) technology. The chemical structures and compositions of the novel copolymers were demonstrated by proton nuclear magnetic resonance (1H NMR) and Fourier transform infrared spectroscopy (FTIR). The molecular weights of the novel copolymers were measured by size exclusive chromatography (SEC) and proved to have a relatively narrow molecular weight distribution coefficient (ÐM ≤ 1.50). The water solubility and transmittance of the novel copolymers were tested via visual observation and UV–Vis spectroscopy, which proved the SPMO had a good hydrophilicity and suitable low critical solution temperature (LCST). The critical micelle concentration (CMC) of the novel polymeric micelles were determined using surface tension method and fluorescent probe technology. The particle size and morphology of the novel polymeric micelles were characterized by dynamic light scattering (DLS) and transmission electron microscopy (TEM). The sol–gel transition behavior of the novel copolymers was studied via vial flip experiments. Finally, the hydrophobic anticancer drug doxorubicin (DOX) was used to study the in vitro release behavior of the novel drug-loaded micelles. The results show that the novel polymeric micelles are expected to become a favorable drug carrier. In addition, they exhibit reductive responsiveness to the small molecule reducing agent dithiothreitol (DTT) and temperature responsiveness with temperature changes.Keywords:temperature/reductive dual-stimulus responsiveness;block copolymers;amphiphilic;ring-opening polymerization;atom transfer radical polymerization
✓ 已验证
产品关联
DOI
PubMed
高影响因子