RSC Advances
·
2020
·Vol. 10
·期 3
·1309-1318
·
IF 3.119
Rengui Weng,Xin Huang,Dongqi Liao,Sheng Xu,Lei Peng,Xinzhong Liu
Bamboo cellulose (BC) is one of the most abundant renewable, hydrophilic, inexpensive, and biodegradable organic materials. The cellulose membrane is one of the best materials for replacing petroleum-based polymer films used for water purification. In this study, N-methylmorpholine-N-oxide (NMMO) was used as a solvent to dissolve cellulose and chitosan, and a regenerated cellulose/chitosan membrane (BC/CSM) was prepared by phase inversion. A new kind of cellulose/chitosan nanofiltration membrane (IP-BC/CS-NFM) was obtained by the interfacial polymerization of piperazine (PIP) and trimesoyl chloride (TMC). The IP-BC/CS-NFM was characterized by Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopy (FE-SEM), atomic force microscopy (AFM), thermal gravimetric analysis (TGA), the retention rate, and water flux. FT-IR analysis showed that polypiperazine amide was formed. Additionally, FE-SEM and AFM showed that a uniform roughness and dense functional layer was formed on the surface of the IP-BC/CS-NFM. Furthermore, TGA analysis showed that the thermal stability of IP-BC/CS-NFM is better than that of BC/CSM. The inorganic salt retention of IP-BC/CS-NFM was measured using a membrane performance evaluation instrument, following the order R(Na2SO4) > R(MgSO4) > R(MgCl2) > R(NaCl). At a pressure of 0.5 MPa, the retention rates for NaCl, Na2SO4, MgSO4, MgCl2, Methyl Orange, and Methyl Blue were 40.26%, 71.34%, 62.55%, 53.28%, 93.65%, and 98.86%, and the water flux values were 15.64, 13.56, 14.03, 14.88, 13.28, and 12.35 L m−2 h−1, respectively. The IP-BC/CS-NFM showed better water flux and a higher rejection rate in aqueous dye-salt solutions, and had a good separation performance under different operating pressure conditions.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2020
·
IF 5.162
Li Niu,Daihui Zhang,Yupeng Liu,Xi Zhou,Jifu Wang,Chunpeng Wang,Fuxiang Chu
Cellulose based hydrogels with a relatively high stretchability were fabricated in the NaOH/urea system via sequential chemical crosslinking and dual network fabrication. The first step involved crosslinking of cellulose using epichlorohydrin as a crosslinker. Cryo-electron microscopy analysis revealed the utilization of diluted acid to treat hydrogels significantly affected the morphology of the first network and improved the mechanical properties. After diffusion of precursors into the first network, the dual network hydrogels were generated after the UV light-initiated polymerization. Raman spectroscopy demonstrated a spatial distribution of second networks within the first network. The compression strength of hydrogels synthesized under the optimized conditions was effectively enhanced from 0.04 MPa to 10.9 MPa. In addition, the tensile properties of hydrogels were easily adjusted via copolymerization of acrylic acid with acrylamide. The highest strain could reach 219.5% with a tensile strength of 1.4 MPa. This work provides a promising and simple strategy to develop a cellulose based hydrogel with enhanced and tunable mechanical properties for wide applications.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF POLYMERS AND THE ENVIRONMENT
·
2020
·Vol. 28
·期 8
·2199-2210
·
IF 2.572
Pei Ruihan,Li Qiqi,Liu Jianting,Yang Guifang,Wu Qiong,Wu Minya,Tong Shengxuan,Lv Yuancai,Ye Xiaoxia,Liu Yifan,Liu Minghua
Abstract Removal of low content of Cr(VI) from water is a critical challenge for water environment protection. Herein, an acrylamide-thiosemicarbazide cellulose aerogels (ATC) was designed by dissolving, grafting and freeze-drying to introduce thiosemicarbazide onto acrylamide-cellulose aerogels (AMC) via Schiff based reaction. The resultant ATC was further employed as an efficient adsorbent to remove low content of Cr(VI) from wastewater by adsorption and reduction. The SEM, FT-IR, and BET results showed that the ATC was composed of well-developed pore structure and owned functional groups such as –NH 2 , C–S and C=S groups. Experimental results indicated that ATC exhibited excellent removal efficiency for 99% under low initial concentration (0.1–10 mg/L). The adsorption isotherms demonstrated ATC adsorbent according to a monolayer adsorption behavior following the Langmuir model with a calculated maximum adsorption capacity of 83.40 mg/g at pH 3, and the adsorption kinetics well obeyed the pseudo-first-order kinetic model. Importantly, the maximum effluent concentration of Cr(VI) was lower than 0.045 mg/L, meeting the standard of WHO (50 μg/L). Furthermore, the main removal mechanisms involved the synergistic effect of electrostatic interactions, reduction and chelation between the positively charged functional groups of adsorbent and the anionic Cr(VI) ions. Graphic Abstract
✓ 已验证
产品关联
DOI
高影响因子
Analytical Methods
·
2020
·Vol. 12
·期 24
·3130-3136
·
IF 2.596
Xiangyu Feng,Jiaying Zhang,Jing Wang,Ailing Han,Guozhen Fang,Jifeng Liu,Shuo Wang
In the synthesis of metal nanoclusters (NCs), small molecules are widely used as capping ligands and reducing agents. However, metal NCs are usually sensitive to solvents and aerobic atmosphere and are also prone to oxidation; thus, their photonic properties deteriorate. In this work, 4-aminothiophenol (PATP) was used as a ligand to prepare Cu NCs and their fluorescence, morphology, and electronic states were characterized. The as-prepared Cu NCs could be dispersed in aqueous media and their fluorescence was sensitive to Hg2+. It was found that after mixing Cu NCs with 2,3-dialdehyde cellulose (DAC) prepared via oxidation by NaIO4, the fluorescence stability of Cu NCs could be enhanced from overnight to 7 days. This might be due to the reaction of the amine group of PATP with the aldehyde group of DAC to form Schiff bases, which are then reduced to form more stable C–N bonds via reduction by NaBH4. Therefore, Cu NCs were attached to a rigid skeleton and their stability increased. Furthermore, the composite of Cu NCs mixed with DAC could be used to prepare colorimetric cards for the rapid detection of Hg2+ with high sensitivity.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
STARCH-STARKE
·
2020
·
IF 2.226
Linjuan Duan,Rongrong Liu,Qun Li
A more efficient Fenton oxidation method with high shear mixing for the preparation of cellulose nanofiber (CNF) is investigated. The Fenton reaction is the reaction between Fe 2+ and H 2 O 2 to produce a series of free radicals that leads to oxidation of the cellulose. With the new technology, the Fe 2+ is preloaded into the kraft pulp by a high shear refining method to realize in situ oxidation of cellulose fibers. It is found that the carbonyl content in the fibers using high shear mixing process is 149.79 μmol g −1 when the dosage of hydrogen peroxide is 0.08 g/g (weight of dry fibers), compared to the 126.40 μmol g −1 of fiber without high shearing when the dosage of hydrogen peroxide is 0.15 g/g, which indicates that the new Fe 2+ pre-loading process has higher oxidation efficiency with lower H 2 O 2 consumption compared with traditional Fe 2+ preloading process. The 13 C NMR results show that the C 2 , C 3, and C 6 hydroxyl groups are oxidized to aldehyde and carboxyl groups, which is beneficial to increase the electrostatic repulsion between fibers and facilitate the subsequent homogenization treatment. The obtained CNF is uniform in size and slightly lower in thermal stability.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2020
·Vol. 137
·期 44
·49350
·
IF 2.52
Feifei Gao,Mingli Jiang,Wencheng Liang,Xiangchen Fang,Fudong Bai,Yan Zhou,Meidong Lang
In this study, a kind of novel composite nanofibrous mats with cellulose diacetate-graft-poly(ethylene terephthalate) (CDA- g -PET) and Type I collagen were obtained by electrospinning and five different ratios of CDA -g- PET/Type I collagen (1:0, 1:0.1, 1:0.2, 1:0.3, 1:0.4) were set to explore the effects of components on its properties. The scanning electron microscope images demonstrated that the formation of uniform and smooth nanofibers with free beads. Compared with pure CDA -g- PET mats, the composite materials transformed into hydrophilic ones with increasing the content of Type I collagen. Moreover, the tensile strength of the composite nanofibrous mats got higher, while its water vapor transmission rate got lower after blending with Type I collagen. In addition, the cell proliferation and adhesion on composite nanofibrous mats were improved according by the results of bone marrow mesenchymal stem cells (BMSCs) culturing experiments. Especially, the cells growth attained optimum when the CDA -g- PET/Type I collagen ratio reached 1:0.3 and 1:0.4, where showed no significant difference. In consequence, the above results indicated that the novel composite nanofibrous mats consisted of CDA -g- PET and Type I collagen obtained by electrospinning combined good mechanical strength of CDA -g- PET and excellent biological functions of Type I collagen. The nanoscale structure might mimic the nanofibrous extracellular matrix feature, which present the potential use in cells culture.
✓ 已验证
产品关联
DOI
高影响因子
IRANIAN POLYMER JOURNAL
·
2020
·Vol. 29
·期 11
·975-983
·
IF 1.707
Lu Chuanwei,Qiu Yuling,Guo Xiaoliang,Wang Chunpeng,Wang Jifu,Chu Fuxiang
UV absorption coating is an important function material, which can protect the substrates from photoaging. In this work, a class of sustainable UV-absorbent copolymers derived from ethyl cellulose (EC), fatty acid and rosin were prepared by a combination of atom transfer radical polymerization (ATRP) and click chemistry. To fulfill this strategy, the pendant azides were first attached onto the backbone of EC. Then, ATRP was applied to fabricate well-defined poly(lauryl methacrylate) (PLMA) bearing terminal alkynes. Finally, click chemistry between the pendant azides in EC and the alkynes in PLMA as well as in rosin esters (DAPE), was performed to achieve the cellulose-rosin graft copolymers (EC-( g -DAPE)- g -PLMA) with UV absorption property. The chemical structure of cellulose-rosin graft copolymers was confirmed by FTIR, 1 H NMR and GPC. Thermodynamic performance analysis indicated that these EC-rosin graft copolymers showed better thermal stability than EC. Due to the synergistic hydrophobic interaction of rosin and the hydrophobic lauryl groups in PLMA, these graft copolymers showed excellent hydrophobic property, and the static contact angles were all above 90°. In addition, all the EC-rosin graft copolymers showed outstanding and stable UV absorption capability, and maintained excellent UV absorption capability after continuous UV-irradiation for 1 h or being heated to 100 °C for 0.5 h, which had potential application in UV absorption materials.
✓ 已验证
产品关联
DOI
高影响因子
CELLULOSE
·
2020
·Vol. 27
·期 12
·7023-7036
·
IF 4.21
Zhou Man,Chen Jingwen,Jiang Mengting,Zhang Yakang,Liang Qian,Xu Song,Yao Chao,Li Zhongyu
A series of thickness-controlled SrTiO 3 (commonly abbreviated ST) anchored on carbonized bacterial cellulose (CBC) was successfully prepared by a novel route of freeze-drying assisted crystallization/carbonization. For the first time, the cross-linked bacterial cellulose served as a carbon source as well as structure-directing scaffold for the construction of ST/CBC composites. Characterizations exhibited cracks and defects on the surface of CBC which provided ideal anchoring sites for the dispersion and crystallization of ST. Additionally, the relationship between morphology and photocatalytic activity of ST/CBC was carefully investigated by photocatalytic reduction of potassium dichromate (K 2 Cr 2 O 7 ) and degradation of tetracycline in water. This unique biomass-derived carbon fibers provide an ideal platform for further design of perovskite based materials with enhanced catalytic performance.
✓ 已验证
产品关联
DOI
高影响因子
CARBOHYDRATE POLYMERS
·
2020
·
IF 7.182
Jinshun Lu,Xiao Han,Lin Dai,Chenyu Li,Jingfeng Wang,Yongda Zhong,Faxin Yu,Chuanling Si
The development of biomass-based hydrogel conductive devices is a promising but challenging subject. Here, cellulose was used to develop a strong, tough, and self-adhesive conductive hydrogel by constructing a synergistic covalent cross-link network and multiple physical interactions. Tannic acid-coated cellulose nanofibrils (TA@CNFs), poly(acrylamide), and ferric ions (Fe 3+ ) were introduced in a composite network by coordination and hydrogen bonds. The strategy of interpenetrating network endowed this hydrogel with high mechanical strength (storage modulus over 14 K Pa), and strong toughness and tensile strength (fracture stress up to 108 K Pa). Chelated Fe 3+ by metal coordination as inorganic conductive phase leads to good electrical conductivity (conductivity up to 3.12 S m −1 ). The obtained hydrogel also exhibited fine flexibility, extensive self-adhesion, and adjustable strain responsiveness for monitoring human joint movements. This work provided a new approach to design conductive hydrogels, and also can expand the application of cellulose-reinforced materials in the sensor field.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CARBOHYDRATE POLYMERS
·
2020
·
IF 7.182
Feng Yu,Hongbing Zhang,Lingzhu Zhao,Zhipeng Sun,Yuli Li,Yan Mo,Yong Chen
With the advent of gel polymer electrolyte (GPE), a series of safety problems of lithium ion batteries have been resolved. However, poor self-standing property, the low ionic conductivity and Li + transference number are still the obstacles that impede the practical application of GPE. Herein, a flexible and eco-friendly GPE is designed using allyl-modified cellulose with methylcellulose through simple UV curing. The crosslinked structure facilitates the integrity of GPE during use, and methylcellulose guarantees the high affinity to liquid electrolyte and improve interfacial compatibility. The specific polar functional groups ( OH, OCH 3 and C O C ) in GPE cooperate to enhance the lithium salt dissociation, anion immobilization and lithium ion transporting and enable the high Li + transference number (0.902) and ion conductivity (4.36 × 10 -3 S cm -1 ). The assembled Li/GPE/LiFePO 4 coin cells possess high initial discharge capacity of 150.6 mA h g -1 and a high capacity retention of 91.6 % after 100 cycles.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
FOOD CHEMISTRY
·
2020
·
IF 6.306
Bing Xie,Xingzhong Zhang,Xiaogang Luo,Yixiang Wang,Yan Li,Bin Li,Shilin Liu
In this work, novel edible coating films based on beeswax-in-water (O/W) Pickering emulsions had been investigated. The Pickering emulsions were stabilized with cellulose nanofibrils (CNFs)/carboxymethyl chitosan (CCS). The emulsions with a droplet diameter of around 10 μm had uniform particle size distribution, and the creaming stability was improved with the increasing the contents of CNFs in the complexes, rheological analysis demonstrated that the Pickering emulsions had an elastic gel-like network. Furthermore, free-standing films were obtained when the emulsions were dried at ambient condition, the tensile strength of the coating films could be 5.0 MPa at a strain of 2.2%, and the water vapor permeability (WVP) value was lower than 2 × 10 −7 g∙h −1 ∙m −1 ∙Pa −1 . Moreover, the coating films could inhibit the growth of typical spoilage organisms such as S. aureus or E. coli, it indicated that the coatings films would have promising applications in antiseptic and fresh keeping for berry fruits.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2020
·
IF 5.162
Dengkun Shu,Peng Xi,Bowen Cheng,Yan Wang,Long Yang,Xiaoqing Wang,Xuhuan Yan
Cellulose nanofibers have been widely applied in many fields because of its unique advantages. However, it is a challenge to prepare cellulose nanofibers by electrospinning directly owing to the special molecular structure of cellulose. This limits the practical applications of cellulose nanofibers. In this work, cellulose nanofibers were successfully prepared directly by design of new electrospinning receiving device and optimization of process parameters. The as-prepared cellulose nanofibers exhibit good oil-water separation performances. Driven solely by gravity, the separation flux of the cellulose nanofibers for mixture of oil and water reaches 34,300.6 L m −2 h −1 , and the separation flux and efficiency for surfactant-stabilized emulsion of oil and water reach 2503.7 L m −2 h −1 and over 98.3%, respectively. The as-prepared cellulose nanofibers also exhibit good mechanical properties and reusability. The breaking strength of the cellulose nanofibers can reach 148.2 cN. The separation fluxes of cellulose nanofibers for mixtures and emulsions of oil and water can be maintained 99.7% and 86.3% of the initial value after being used for 20 times. Furthermore, the as-prepared cellulose nanofibers have good degradability. These properties render as-prepared cellulose nanofibers as promising materials with potential applications in oil-water separation.
✓ 已验证
产品关联
DOI
PubMed
高影响因子