Journal of Materials Chemistry C
·
2023
·Vol. 11
·期 13
·4492-4499
·
IF 6.4
Xulong Lv,Xihui Shan,Yi Zhang,Yanjie Liang
Photostimulated luminescence (PSL) materials have attracted considerable attention in many important fields, varying from radiation dosimetry and biomedical imaging to security encryption and optical data storage. Nevertheless, monochromatic light illumination is usually used as the stimulus source to realize the absolute separation between the PSL signal and the excitation light. Furthermore, a dark environment is considered necessary to get rid of the interference from polychromatic ambient light. Herein, we report a glow-in-the-daylight material, YBO3:Pr3+, which can emit intense and long-lasting ultraviolet-C (UVC) persistent luminescence in a bright indoor lighting or outdoor sunlight environment after ceasing X-ray excitation. We note that although the YBO3:Pr3+ phosphor shows very weak UVC afterglow in darkness, remarkable enhancement of UVC persistent luminescence can be observed in a bright ambient light environment. The UVC persistent luminescence peaking at 274 nm can last for more than 24 h under the illumination of 900 lux white LED light, and the UVC luminescence signal is free from the interference of the ambient light. This enhancement of UVC persistent luminescence is assigned to the continuous and efficient photostimulation of polychromatic ambient light, which has been confirmed by comprehensive spectroscopic investigations. The appealing glow-in-the-daylight phenomenon from the YBO3:Pr3+ phosphor will not only lay the foundation to develop more UVC persistent phosphors suitable for working in a bright environment, it will also promote the widespread use of these storage phosphors across a broad range of applications such as microbial inactivation and optical tagging.
✓ 已验证
产品关联
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2023
·
IF 5.2
Shiquan Zhang,Jian Zhang,Suohui Yang,Minxian Shi,Junguo Li,Qiang Shen
Ablation material had been widely used in aerospace attributed to its reliability and strong adaptability but was usually accompanied by low strength at higher temperatures. Here, a high flexural strength of 66.91 MPa after ablation at 1500 °C of carbon fiber/boron phenolic resin (CF/BPR) composite modified by MoSi 2 and mica was reported. With the proportion of MoSi 2 and mica was 9:1, the formed appropriate content of the liquid phase improved the reactivity of MoSi 2 powders and provided a suitable interfacial state between CF and the matrix. The result of the oxygen-acetylene test showed that the mass ablation and the linear ablation reduced to 0.034 g/s and 0.006 mm/s, respectively. Owing to the formed liquid phase wrapping the carbon fiber and ceramic layer on the surface improved the ablation resistance. These high-strength CF/BPR composites have strong potential in new aerospace materials.
✓ 已验证
DOI
高影响因子
Materials
·
2023
·Vol. 16
·期 6
·2495
·
IF 3.4
Qian Yang,Cuiyan Li,Haibo Ouyang,Ruinan Gao,Tianzhan Shen,Jianfeng Huang
Porous (Ta0.2Nb0.2Ti0.2Zr0.2Hf0.2)C high-entropy ceramics (HEC) with a dual-porosity structure were fabricated by pressureless sintering using a mixture powder of ceramic precursor and SiO2microspheres. The carbothermal reduction in the ceramic precursor led to the formation of pores with sizes of 0.4–3 μm, while the addition of SiO2microspheres caused the appearance of pores with sizes of 20–50 μm. The porous HECs exhibit competitive thermal insulation (4.12–1.11 W·m−1k−1) and extraordinary compressive strength (133.1–41.9 MPa), which can be tailored by the porosity of the ceramics. The excellent properties are ascribed to the high-entropy effects and dual-porosity structures. The severe lattice distortions in the HECs lead to low intrinsic thermal conductivity and high compressive strength. The dual-porosity structure is efficient at phonon scattering and inhabiting crack propagations, which can further improve the thermal insulation and mechanical properties of the porous HECs.Keywords:high-entropy carbides;pressureless sintering;porous ceramics;thermal conductivity;compressive strength
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CONSTRUCTION AND BUILDING MATERIALS
·
2023
·
IF 7.4
Chenchen Xiong,Yulin Wang,Yang Zhou,Xingyu Liu,JinHui Tang,Pan Feng
An ordered structure and high mechanical property of calcium silicate hydrate (C-S-H) gel has been always pursued in the field of cementitious materials. In this paper, compacted and layer-by-layer stacking C-S-H plates were fabricated based on Layer-by-Layer (LBL) method and H-cell penetration (HCP) method through cation exchange membrane templating. This new way changed the randomly packing structure of traditional C-S-H, and synthesized a high-orderly C-S-H platelets with denser structure. Based on molecular dynamics simulations, it can be attributed to the strong adsorption and nucleation sites contributed by sulfonic acid groups on the cation exchange membrane. Besides, AFM indentation experiments indicate this C-S-H owns significantly higher elastic modulus than traditional C-S-H, while the mechanical properties can be further increased by the addition of PVA and the regulation of reaction time. This new type C-S-H may pave the way to the preparation of high-performance concrete in the future.
✓ 已验证
产品关联
DOI
高影响因子
NEW JOURNAL OF CHEMISTRY
·
2023
·Vol. 47
·期 16
·7583-7587
·
IF 3.3
Baole Li,Tiansheng He,Chen Zuo,Zhi Cao,Taihong Yan,Weifang Zheng
Catalytic decomposition of hydrazine nitrate is a very important research topic in the environmental protection field. Herein, we used an Ru/C catalyst for the decomposition of hydrazine nitrate in HNO3, and the reaction kinetics and mechanism were studied in detail. The kinetics study of the decomposition of hydrazine nitrate (0.01 M) was conducted in the temperature range 313–343 K in 0.1 M HNO3 in the presence of Ru/C. The apparent activation energy for this reaction was 46.6 kJ mol−1 according to a fitting of the experimental data, while the reaction order was 1.5. It was also found that the reaction pathway of the catalytic decomposition of hydrazine nitrate on the Ru/C catalyst involved two processes: heterogeneous catalytic disproportionation of hydrazine nitrate at the catalyst surface and oxidation of hydrazine nitrate with catalytically generated HNO2.
✓ 已验证
产品关联
DOI
高影响因子
CORROSION SCIENCE
·
2022
·
IF 7.72
Ling He,Ling Pan,Wei Zhou,Zibo Niu,Peng Xiao,Yang Li
In this work, the corrosion behavior of Yb 4 Hf 3 O 12 ceramics under CFAS coupled with water vapor environment at 1400 °C for 2–50 h was investigated. Results show that the CFAS were rapidly dissolved into ceramics under test environment, and then the Yb-Ca-Si apatite and Hf-rich fluorite phases were re-precipitated. Simultaneously, the water vapor corrosion mainly induced grain surface corrosion, resulting in the formation of corrosion pits and ridge-like structures. Moreover, the pores and microcracks caused by water vapor corrosion offer additional penetration path for CFAS melt.
✓ 已验证
产品关联
DOI
高影响因子
Sustainable Energy & Fuels
·
2019
·Vol. 3
·期 12
·3455-3461
·
IF 4.912
Bomin Feng,Xiuju Wu,Yanli Niu,Wei Li,Yunxi Yao,Weihua Hu,Chang Ming Li
Fe/N–C catalysts show great potential for the oxygen reduction reaction (ORR) but their catalytic activity should be further improved for practical application. Here, we report a high performance Fe/N–C hollow sphere with excellent ORR activity in both alkaline and acidic solutions. It is synthesized via pyrolysis of a melamine/Fe-incorporated polydopamine nanosphere precursor at 800 °C in an argon atmosphere. The N-rich melamine in the precursor affords abundant N dopants to form dense Fe–Nx active sites and also facilitates the formation of micropores in the catalyst via the gasification effect, together improving the ORR activity. The as-reported Fe/N–C catalyst outperforms the Pt/C catalyst in basic media (45 mV more positive half wave potential), approaches the Pt/C catalyst in acidic media (55 mV lower half wave potential), and exhibits impressive performance in Zn–air primary batteries.
✓ 已验证
产品关联
DOI
高影响因子
RSC Advances
·
2018
·Vol. 8
·期 7
·3858-3868
·
IF 2.936
Shuohan Yu,Sheng Xu,Bowen Sun,Yiyang Lu,Lulu Li,Weixin Zou,Peng Wang,Fei Gao,Changjin Tang,Lin Dong
Chromium oxide nano-particles with an average diameter of 3 nm covered by amorphous carbon (CrOx/C) were successfully synthesized. The synthesized CrOx/C materials were used for the selective catalytic reduction of NOx by NH3 (NH3-SCR), which shows superb NH3-SCR activity and in particular, satisfactory regeneration ability in the presence of SO2 compared with Mn-based catalysts. The as-prepared catalysts were characterized by XRD, HRTEM, Raman, FTIR, BET, TPD, TPR, XPS and in situ FTIR techniques. The results indicated presence of certain amounts of unstable lattice oxygen exposed on the surface of CrOx nano-particles with an average size of 3 nm in the CrOx/C samples, which led to NO being conveniently oxidized to NO2. The formed NO2 participated in NH3-SCR activity, reacting with catalysts via a “fast NH3-SCR” pathway, which enhanced th NH3-SCR performance of the CrOx/C catalysts. Furthermore, the stable lattice of the CrOx species made the catalyst immune to the sulfation process, which was inferred to be the cause of its superior regeneration ability in the presence of SO2. This study provides a simple way to synthesize stable CrOx nano-particles with active oxygen, and sheds light on designing NH3-SCR catalysts with highly efficient low temperature activity, SO2 tolerance, and regeneration ability.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
MICROCHIMICA ACTA
·
2018
·Vol. 185
·期 8
·1-7
·
IF 5.705
Hu Yanling,He Yu,Han Yaxue,Ge Yili,Song Gongwu,Zhou Jiangang
Stable copper nanoclusters (CuNCs) were prepared by utilizing D-penicillamine as both the stabilizer and reductant. The emission of the CuNCs (with excitation/emission peaks at 390/645 nm) is largely stabilized by coating with poly(sodium-p-styrenesulfonate) (PSS). Cytochrome c (Cyt c) quenches the fluorescence of the PSS-coated CuNCs, and this effect was exploited to design a quenchometric fluorometric assay for Cyt c. If trypsin is added to the loaded CuNCs, it will hydrolyze Cyt c to form peptide fragments, and fluorescence is gradually restored. A highly sensitive and fluorometric turn-off-on assay was constructed for sequential detection of Cyt c and trypsin. The linear ranges for Cyt c and trypsin are from 8.0 nM to 680 nM, and from 0.1 to 6.0 μg mL −1 , and the lower detection limits are 0.83 nM and 20 ng mL −1 for Cyt c and trypsin, respectively.
Schematic illustration of the fluorometric assay for trypsin based on the electron transfer between poly(p-styrenesulfonate)-protected copper nanoclusters (PSS-CuNCs) and cytochrome c (Cyt c).
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF ELECTROANALYTICAL CHEMISTRY
·
2018
·
IF 3.235
Qingfeng Zhou,Yun Gong,Jianhua Lin
NiV 2 O 6 /C composites are prepared via a solid-state conversion process by low temperature (150 °C) annealing nickel‑vanadium-based coordination polymer , [Ni(phen)H 2 O][V 2 O 6 ]. The obtained NiV 2 O 6 /C nanoribbons are interconnected to form a sponge-like morphology, when the composites are first used as supercapacitor electrode, it exhibits a specific capacitance of 745.6 F g −1 at 0.5 A g −1 with a good rate capability of 520.0 F g −1 (69.7% retention) at 10 A g −1 (20-folds). The NiV 2 O 6 /C composite exhibits good cycling performance, the capacitance retentions at 6000th and 12000th charging/discharging cycles at 2 A g −1 are 81.5% and 77.8% relative to the original capacitances, respectively. The morphological and compositional changes of the NiV 2 O 6 /C composite electrode before and after 12,000 GCD cycles (two-electrode system) are carefully elaborated through a series of characterization (SEM, EDS , and XPS). Furthermore, the NiV 2 O 6 /C nanoribbons possess reversible electrochromism , which is probably related to the intervalence charge transfer (IVCT, V IV → V V ).
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS
·
2018
·
IF 2.606
Kejia Kang,Rong Tu,Guoqiang Luo,Jian Zhang,Jiawen Zhu,Qiang Shen,Lianmeng Zhang
In this research, the high-temperature mechanical, electrical and thermal properties of arc-melted W-based composites with a small amount of SiC additives were investigated. The high-temperature mechanical properties of tungsten were enhanced by the presence of the hard ceramic phase (W 5 Si 3 and W 2 C) and the interaction of dislocations. The ceramic phase also played a role in inhibiting the grain growth at high temperatures. The ultimate compressive strength (UCS) of the W with 1 wt% SiC (S1) was 968.9 MPa at 1273 K, which is three times that of pure W (291.9 MPa) at 1273 K, showing a significant enhancement in high-temperature strength . Both thermal conductivity ( κ ) and electrical conductivity ( σ ) decreased with the increasing of SiC addition. With increasing temperature, the σ decreased while the κ increased due to the intrinsic behavior of the ceramic phase in the composites.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2018
·Vol. 29
·期 24
·20580-20587
·
IF 2.324
Fang Lu,Xue Yan,Hu Xing-Ming,Xie Dong,Li Wen-Jun
Electrochemiluminescence (ECL) is a very sensitive method for trace analysis because of its background interference and high signal-to-noise ratio. In the past decade, the determination of Cu 2+ in environment has attracted considerable attention since it plays an essential role in many physiological processes. Herein, a novel ECL sensor based on C,N quantum dots embedded g-C 3 N 4 nanosheets (C,N-QDs@NSs) was constructed for the detection of Cu 2+ . The nanocomposite was rapidly obtained via the oxidation of normal g-C 3 N 4 in H 2 O 2 solution using sonochemical synthesizing method. Due to the abundant surface defects on C,N-QDs@NSs, the ECL intensity was magnified 2.5 times for using a C,N-QDs@NSs electrode in comparision to a g-C 3 N 4 modified electrode. Besides, C,N-QDs@NSs could accelerate the rate of electron transfer in ECL reaction and thus resulted in the lower cathodic peak potential. Significantly, Cu 2+ could effectively quench the ECL of C,N-QD@NSs, which endowed C,N-QD@NSs with a great advantage in the ECL detection of Cu 2+ . under optimum conditions, C,N-QDs@NSs modified electrode exhibited a linear detection range from 5 × 10 −4 to 10 µM with a detection limit of 2 × 10 −4 µM (S/N = 3) for Cu 2+ , and was finally applied to detect Cu 2+ in real samples with satisfactory results.
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）