INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2023
·
IF 8.2
Duoduo He,Liying Qian,Xingyu Chen,Beihai He,Junrong Li
Electromagnetic interference (EMI) shielding paper with durability and high effectiveness is of significant importance to long-term service for preventing EMI pollution. Herein, we report a practical method for preparing cellulose paper/Ag composite with outstanding durable and ultrahigh EMI shielding performance by electroless silver plating. The silver deposition process, the surface morphology, the silver content and conductivity of the composite can be controlled by varying the amount of N -acetyl-L-cysteine (NAC) grafted onto the cellulose fibers and ammonia amount for silver-ammonia complex formation. Moreover, the grafted NAC with thiol groups on cellulose can enhance the adhesion between silver and cellulose paper, meanwhile, NAC as the reducing agent can result in a more complete flower-shaped silver structure and reducing the reflection of electromagnetic waves in silver layer. The composite exhibited excellent conductivity, EMI shielding effectiveness (SE) up to 106 dB and outstanding durability. After 10,000 bending times and 60 abrasion cycles respectively, the electrical resistance of the composite only increased from 0.030 Ω/sq. to 0.041 Ω/sq. and 0.050 Ω/sq., and the EMI SE decreased to 102 dB and 105 dB.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2023
·
IF 8.2
Hong Li,Jianhua Zhou,Jiarui Yu,Jiaojiao Zhao
The development of environmental-friendly self-healing nanocomposites has attracted much attention. In this paper, the light-activated cellulose nanocrystals/ fluorinated polyacrylate-based waterborne coating based on the reversible cycloaddition reaction of the coumarin groups was prepared via Pickering emulsion polymerization. The cellulose nanocrystals (CNCs) modified by the PDMAEMA- b -PGMA- b -P(HFBA- co -VBMC) copolymer were studied via FT-IR and TGA . In addition, the dispersity and interface behavior of CNCs before and after modification were investigated by DLS and interfacial tension measurements. Afterwards, we focused on the influence of modified CNCs, PDMAEMA- g -CNC- g- P(HFBA- co -VBMC) (MCNC) dosage on the Pickering emulsion, emulsion polymerization and properties of latex film. The droplet diameter of Pickering emulsion gradually reduced with the increase of MCNC dosage. The MCNC dosage for the minimum average size and optimum stability of latex particles was 1.0 wt%. Moreover, the latex film comprising 1.0 wt% MCNC presented not only high tensile stress (6.0 MPa), large elongation at break (567.70 %) and superior oil/water repellency but also excellent self-healing properties. The outstanding self-healing capability of latex film was attributed to the reversible light-activated dimerization of coumarin groups. The preparation method for the advanced performance waterborne cellulose nanocrystals/fluorinated polyacrylate will provide valuable guidance for the development of versatile materials.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Polymers
·
2023
·Vol. 16
·期 1
·14
·
IF 5
Yun Peng,Shuang Zhao,Chuanlin Huang,Feifei Deng,Jie Liu,Chunhua Liu,Yibao Li
Super-wetting interface materials have shown great potential for applications in oil–water separation. Hydrogel-based materials, in particular, have been extensively studied for separating water from oily wastewater due to their unique hydrophilicity and excellent anti-oil effect. In this study, a superhydrophilic and underwater superoleophobic bamboo cellulose hydrogel-coated mesh was fabricated using a feasible and eco-friendly dip-coating method. The process involved dissolving bamboo cellulose in a green alkaline/urea aqueous solvent system, followed by regeneration in ethanol solvent, without the addition of surface modifiers. The resulting membrane exhibited excellent special wettability, with superhydrophilicity and underwater superoleophobicity, enabling oil–water separation through a gravity-driven “water-removing” mode. The super-wetting composite membrane demonstrated a high separation efficiency of higher than 98% and a permeate flux of up to 9168 L·m−2·h−1for numerous oil/water mixtures. It also maintained a separation efficiency of >95% even after 10 cycles of separation, indicating its long-term stability. This study presents a green, simple, cost-effective, and environmentally friendly approach for fabricating superhydrophilic surfaces to achieve oil–water separation. It also highlights the potential of bamboo-based materials in the field of oil–water separation.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Polymer-Plastics Technology and Materials
·
2023
·
IF 2.7
Qianyong Liang,Ying Pan,Jia Du,Dong Zhang,Yan Zhang,Zhishun Zhong,Hongting Zhao
Carbon sphere@layered double hydroxides filled cellulose nanofibers (ACS@LDHs/CNF) aerogel was successfully synthesized. The removal rate of Cr(VI) using ACS@LDHs/CNFs aerogel at a solid-liquid ratio of 1 g/L was 89.4%, which was higher compared to the removal rate of 65.2% using LDHs alone. The adsorption capacity of ACS@LDHs/CNFs for Cr(VI) was determined to be 44.9 mg/g. The adsorption kinetics followed the pseudo-second-order kinetic equation, and the isotherm data showed good agreement with the Langmuir model. The adsorption mechanism of Cr(VI) onto ACS@LDHs/CNFs aerogel was also investigated. Additionally, the ACS@LDHs/CNFs aerogel demonstrated consistent high adsorption efficiency over 4 consecutive cycles of adsorption-regeneration.
✓ 已验证
产品关联
DOI
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2023
·
IF 5.2
Feiya Fu,Qinqin Chen,Lihuan Chen,Shaojie Cai,Yuxin Lan,Zijun Pan,Haidong Li,Juming Yao,Xiangdong Liu
Mechanically twisting a yarn is a useful and important method for creating internal stress, changing macromolecular orientation, and affording interesting fiber properties, including mechanical, structural, physical and chemical properties. Bacterial cellulose (BC) nanofibers are a new type of highly crystalline bionanofibers exhibiting excellent intrinsic mechanical properties . Herein, BC macrofibers with a diameter of 0.35–0.53 mm were prepared from BC hydrogel films using a two-step technique involving drying and twisting processes. Moreover, the effects of the drying method (oven- and freeze-drying) and those of the processing steps on the morphologies, structures, and physicochemical properties of the macrofibers were investigated. Results indicated that only the wet twisting–first process affords continuous macrofibers with a compact and uniform structure. The tensile strength and elongation at break of the macrofibers were 199 MPa and 24%, respectively. Furthermore, by introducing graphene oxide (GO) to the macrofibers, a photothermal and moisture actuator was facilely constructed, which could produce a twisting motion of 0.39 rpm and an untwisting motion of 0.6 rpm. This study provides insights into methods to easily alter the properties of BC macrofibers, which is pivotal for the macrofiber’s potential application in intelligent devices.
✓ 已验证
产品关联
DOI
高影响因子
ENVIRONMENTAL RESEARCH
·
2023
·
IF 8.3
Yujie Li,Jia Wang,Chao Liu,Long Wang,Peng Zhang,Qianyu Zhao,Zhu Xiong,Gaosheng Zhang,Wei Zhang
Schwertmannite (SCH) is a promising material for adsorbing inorganic arsenic (As). We synthesized SCH nanoparticles (nano-SCH) via a modified chemical oxidation method and investigated the application of nano-SCH for the remediation of As-contaminated soils. The production of nano-SCH was successfully prepared using the persulfate oxidation method with carboxymethyl cellulose stabilization. The spherical structure of the nano-SCH particles had an average hydrodynamic diameter of 296 nm with high specific surface areas (108.9 m 2 /g). Compared with SCH synthesized via the H 2 O 2 oxidation method, the percentage of Fe 3+ precipitation in nano-SCH synthesis increased from 63.2% to 84.1%. The inorganic As adsorption capacity of nano-SCH improved by 2.27 times at solution pH = 6. After remediation of heavily As-contaminated soils by using 5% nano-SCH, the leachability of inorganic As rapidly decreased to 0.01% in 30 d. Correspondingly, the immobilization efficiencies of inorganic As in soil reached >99.9%. The inorganic As fractions in treated soil shifted from specifically and nonspecifically bound forms to amorphous and crystalline hydrous oxide-bound fractions. After treatment with 5% nano-SCH for 60 d, soil pH slightly decreased from 5.47 to 4.94; by contrast, soil organic matter content increased by 20.9%. Simultaneously, dehydrogenase concentration in soil decreased by 22.4%–34.7% during the remediation process. These changes in soil properties and As immobilization jointly decreased microbial activity and initiated the re-establishment of bacterial communities in the soil. In summary, this study presents a novel and high-productivity technology for nano-SCH synthesis and confirms the high As immobilization effectiveness of nano-SCH in the remediation of As-contaminated soils.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2023
·
IF 4.2
Ge Li,Bingtao Zhang,Zhe Tan,Ling Jiang,Zhikan Yao,Lin Zhang
Cellulose, a sustainable raw material, holds great promise as an ideal candidate for membrane materials. This work focused on establishing a green route for fabricating cellulose nanofiltration membranes by reusing a binary solvent of a mixture of ionic liquid (IL) 1-ethyl-3-methylimidazolium acetate and dimethyl sulfoxide (DMSO). The rheological and thermodynamic properties of cellulose solutions were thoroughly investigated to gain fundamental insights into cellulose membrane formation using a mixture solvent. The morphologies and separation performances of the cellulose membranes were also studied. Based on these results, we successfully developed a cellulose membrane with a remarkable water flux of 101.8 L/m2·h, and the rejections for both Congo Red and Evans Blue were higher than 99.7%. Furthermore, the cellulose membrane demonstrated excellent antifouling performance and stability in long-term operation. Moreover, we conducted an attempt on the recycling and reuse of IL and DMSO, revealing that the structure and separation performance of the cellulose membrane produced using the recovered solvent were comparable to those of the membrane obtained using the original solvent. These results highlighted a sustainable approach to fabricating high-performance cellulose membranes.
✓ 已验证
产品关联
DOI
高影响因子
CARBOHYDRATE POLYMERS
·
2023
·
IF 11.2
Weina Wu,Ying Zhou,Jiefeng Pan,Yingying Wu,Gulden Goksen,Ping Shao
In this study, F-ZnO NPs were used as antibacterial agents , mussel bionic dopamine exerted its adhesive action to immobilize F-ZnO NPs on the pectin/CNF aerogel skeleton. Fruit and vegetable antimicrobial mats with safety, long duration of action and high efficiency were prepared and its potential application has been investigated. The results showed that a dopamine layer was deposited on the surface of the CNF , which promoted the tight adhesion of the F-ZnO NPs to the aerogel skeleton. The F-ZnO@D-CNF aerogel exhibited a slow release of zinc ions , with the first two days being 0.40 ± 0.16 and 1.01 ± 0.13 mg/mL. The aerogel was light, can stand on the petals without collapsing, has regular and uniform pore structure , good tensile/compressive properties and high antibacterial/anti-fungal properties. Strawberries packaged with F-ZnO@D-CNF aerogel exhibited an extended shelf life of 5 days. Additionally, the strawberries maintained a soluble solid content of 6.9 ± 0.82 % and a Vc content of 44.67 ± 3.51 mg/100 g. The weight loss, color and firmness were also notably superior to the other four groups. The final concentration of zinc ions in strawberries was 3.71 ± 0.28 μg/g, which is far below the recommended dietary intake.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CELLULOSE
·
2023
·Vol. 30
·期 12
·7763-7777
·
IF 5.7
Shen Yun,Li Bin,Wu Meiyan,Chen Xiuping,Guan Yihao,Wang Shuangjia,Li Yiming
Oil gelling agent serves as potential materials in the treatment of marine oil pollution. However, the reported oil gelling agents have some limitations in practical applications, such as the high cost, complex synthesis, secondary pollution, and the lack of enough storage space for the inorganic oil gelling agents. Here, a novel powdery oil gelling agent with a hierarchical porous structure was developed and used in remediating oil pollution on the water surface. Based on the three-dimensional (3D) network of cellulose nanofibrils/silicon dioxide (CNFs/SiO 2 ), it was found that GO acted as a larger skeleton and formed a double skeleton 3D network with CNFs to successfully construct the oil gelling agent (S/GO/CNFs/SiO 2 , SGCS) with hierarchical porous structure and selective wettability. SGCS can efficiently solidify various oil independent of environmental factors (temperature and pH), especially the accessibility of the large pores and the capillary action of the small pores contribute to the faster solidifying of crude oil. Resulting from the photothermal conversion function of GO, it shows the ability to recovery oil from the solidified state to achieve higher economic benefits. This study overcomes to a certain extent the current limitations of oil gelling agents and will provide powerful support for the application of oil gelling agents in practical marine oil spills. Graphical abstract Double skeleton powdery oil gelling agent constructed by cellulose nanofibrils and graphene oxide was successfully fabricated and utilized to effectively remove marine oil spill.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2023
·
IF 15.1
Na Li,Koukou Tao,Wei Xia,Chunwei Yu,Hu Yang
A novel fully environmental-friendly organic–inorganic ternary hybrid aerogel (LN/MMT@cellulose), composed of lignin (LN), montmorillonite (MMT), and cellulose, was designed and simply fabricated. LN/MMT@cellulose was employed for the adsorptive removal of typical antibiotic ciprofloxacin (CIP) in water. The combined MMT and LN reinforce the mechanical properties of the cellulose aerogel and notably enhance the selective adsorption capacity toward CIP in the presence of various inorganic and organic matters. LN/MMT@cellulose still presents good adsorption ability toward CIP even at the CIP concentration as low as 0.002 mmol/L in various actual water sources. With the combination of the adsorption kinetics, isotherms, and thermodynamic study as well as the various spectroscopic characterizations before and after adsorption, the mechanisms of LN/MMT@cellulose in CIP adsorption were investigated in detail. Various interactions were involved in CIP adsorption by this composite aerogel under different pH levels, causing the evident pH dependence of its adsorption capacity, specifically, the cation exchange and electrostatic attractions associated with the chelation, π-π electron donor–acceptor interaction, and the ordinary hydrogen bondings were dominant at pH < 6.0, but the complexation and negatively charged assisted hydrogen bondings played the key roles under neutral and alkaline conditions. LN/MMT@cellulose had a slight loss in adsorption ability toward CIP and sustained physicochemical structural stabilities, even after seven adsorption–deadsorption cycles. In addition to CIP, LN/MMT@cellulose could be efficiently used for the adsorptive removal of two other popular antibiotics, namely, tetracycline, and trimethoprim. The said vital characteristics of LN/MMT@cellulose confirmed it is a promising material for the adsorptive removal of antibiotics in practical water treatment.
✓ 已验证
产品关联
DOI
高影响因子
Foods
·
2023
·Vol. 12
·期 9
·1857
·
IF 5.2
Ruoting Liu,Wenrui Chi,Qihao Zhu,Hailan Jin,Jian Li,Lijuan Wang
A cellulose-based matrix for monitoring milk freshness (MF) was produced from rice straw particles (RSPs) in a 0.125–0.150 mm that was bis-quaternized to attach bromocresol purple (BP) as a sensor. Under alkali conditions, the obstinate structure of the rice straw had opened, thereby improving the accessibility of the cellulose. Bis-quaternization created more adsorption sites for BP. The maximum adsorption capacity was 97.68 mg/g. The sensors were interwoven with cellulosic fibers to form the cellulose-based label with a relatively loose three-dimensional structure via hydrogen bonds. As the proportion of BP-BCRPs was increased from 10% to 40%, the air permeability of the label increased from 3.76 to 15.01 mm/s, which increased the response to the tested gases (10.12 s for 1 mL of acetic acid). The intelligent label exhibited excellent sensitivity at pH values of 3–9 with highly saturated color changes. During the storage period, the label color shifted from blue-purple to yellow as acidity was increased from 17.24 to 19.8 °T due to capillarity action, providing a timely warning to consumers. The prepared colorimetric porous intelligent cellulose-based label is suitable for monitoring of MF.Keywords:bis-quaternary ammonium salt;porous cellulose-based label;capillarity;pH sensitivity;milk freshness
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CELLULOSE
·
2023
·Vol. 30
·期 12
·7745-7762
·
IF 5.7
Lang Daning,Zhang Chengbo,Qian Qianqian,Guo Chengxin,Wang Lingling,Yang Chao,Wu Ronglan,Wang Wei,Wang Jide,Fu Jihong
The occurrence of oil spills has severe damage upon both the environment and human health. Hence, the development of a green, recyclable, complex environment resistant, and efficient oil–water separation aerogel is required in order to effectively absorb marine or industrial oil. In this study, modified cellulose/N,N'-methylenebisacrylamide/tannin (PCMT) composite porous materials were prepared utilizing the sol–gel method and were modified with tertbutyl acrylate. PCMT possesses a three-dimensional interpenetrating porous structure, exhibiting remarkable oil–water separation performance and excellent compressive strength (PCMT can capable of bearing 7000 times its own weight; PCMT can endure 290.3 kPa pressure at 80% strain when the amount of tannin is 0.2 g). The unique pore structure of PCMT engenders differential oil adsorption capacities (PCMT0, PCMT0.05, PCMT0.1, and PCMT0.2 evince higher adsorption capacities for petroleum ether and dichloromethane, n-hexane and dichloromethane, toluene, and toluene and dichloromethane, respectively). Of critical import, PCMT demonstrates exceptional adaptability to complex environments, wherein the porous materials maintain good hydrophobicity and oil absorption capacity under conditions of vigorous stirring, a wide pH range (1–14), a wide temperature range (4–160 °C), ultraviolet irradiation (8 h), and tape peeling (10 times). Moreover, the porous materials may be employed for the recovery of oil through simple mechanical extrusion, thus demonstrating certain economic significance and the application potential in the treatment of oil spills.
✓ 已验证
产品关联
DOI
高影响因子