Desalination and Water Treatment
·
2024
·
IF 1
ZiJie Wang,Zheng Wang,Kai Xu,Lei Chen,ZiZeng Lin,YaLi Liu
Granular-activated carbon is a commonly used adsorbent in water treatment. It can be reused by regeneration when saturated, but there are limits to the number of regenerations in actual engineering. This study created a simple and economical treatment method allowing for the reuse of waste granular-activated carbon (WGAC) that approaches the regeneration limit. The adsorption kinetics, equilibrium, and thermodynamics of Ni(II) onto the treated waste granular-activated carbon (TWGAC) and the new granular-activated carbon (NGAC) were studied. The N 2 adsorption/desorption isotherms, zeta potential, SEM, energy-dispersive spectrometry and FTIR spectra were used to characterize and compare the NGAC and TWGAC. Analysis revealed that the structure of WGAC was severely damaged, but the adsorption capacity and adsorption mechanism after treatment were similar to those of NGAC. Experimental data showed that the pseudo-second-order kinetic model and the Freundlich isothermal model had high correlation coefficients (R 2 > 0.99). The maximum adsorption capacity of TWGAC and NGAC was 138.9 and 123.5 mg g –1 . Thermodynamic parameters, including the negative values ΔG, positive values ΔH, and positive value ΔS, indicated that the current adsorption processes of TWGAC and NGAC were feasible, spontaneous and endothermic. After three cycles, TWGAC’s removal rate for Ni(II) remained as high as 95.3%.
✓ 已验证
DOI
高影响因子
SOLAR ENERGY
·
2019
·
IF 4.674
Weihua Fei,Yun Song,Najun Li,Dongyun Chen,Qingfeng Xu,Hua Li,Jinghui He,Jianmei Lu
A visible-light-active Ni foam@ZnO@ZnFe-LDH composite photocatalyst was fabricated with well-defined porous 2D/2D interconnected nanosheets of ZnO and binary ZnFe layered double hydroxide (ZnFe-LDH) growing vertically on the Ni foam substrate. In view of the excellent conductivity of Ni foam, it can be used as an electrode substrate to deposit ZnO nanosheets on the surface by electrodeposition . Then the ultrathin layered 2D ZnFe-LDH was uniformly coated on ZnO nanosheets by hydrothermal method. A highly effective three-electrode photoelectrocatalytic (PEC) system was constructed with Ni foam@ZnO@ZnFe-LDH as photoanode. The 2D/2D core-shell heterojunction formed between ZnO core and ZnFe-LDH shell not only resulted in a narrowing bandgap and increased the visible light absorption of the ZnO, but also promoted the migration of the photogenerated electrons and then the degradation efficiency with a low applied potential was greatly improved. The dyes (Acid Red 1 as model) and hexavalent chromium ions (Cr(VI)) in water can be simultaneously removed by oxidation reaction on the anode and reduction reaction on the cathode, respectively. In addition, the Ni foam@ZnO@ZnFe-LDH composite photocatalyst also showed outstanding stability during the application process. Thus, the photoelectrocatalytic synergitic effect based on Ni foam@ZnO@ZnFe-LDH gives a simple and effective strategy to fast remove Cr(VI) and organic pollutants in PEC process at low voltage.
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2021
·Vol. 46
·期 55
·28134-28143
·
IF 5.816
Jisheng Yang,Kemin Zhang,Zhewen Ma,Xu Zhang,Tianping Huang,Subrata Panda,Jianxin Zou
Herein, a new type of trimesic acid-Ni based metal organic framework (TMA-Ni MOF) was synthesized and then, its derivative Ni@C was introduced into MgH 2 as destabilizer through high energy ball milling to prepare a Mg–Ni@C–H composite. X-ray diffraction analyses indicate the formation of Mg 2 Ni/Mg 2 NiH 4 as major phases after dehydrogenation/rehydrogenation of the composite, respectively. Two hydrogen absorption plateaus are observed in the Mg–Ni@C–H composite, corresponding to the hydrogenation of Mg and Mg 2 Ni, with the enthalpy change values of −75.8 and −52.3 kJ mol −1 H 2 respectively. Thus, it can be concluded that a destabilization effect is brought by Ni@C on thermodynamic properties of MgH 2 . In addition, the hydriding/dehydriding kinetics of MgH 2 is notably accelerated with the addition of Ni-based MOF derivative. The activation energy values of both hydrogen absorption and desorption are significantly lowered down with the assistance of Ni@C. Moreover, stable hydrogen de/absorption capacity and kinetics are remained during 25 cycles of high-rate re/dehydrogenation, which can be ascribed to the carbon-wrapped structure of the composite, with which the aggregation of the nanosized particles can be evidently avioded.
✓ 已验证
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2021
·
IF 9.229
Liang Luo,Ding Wang,Zhongren Zhou,Peng Dong,Shunyi Yang,Jianguo Duan,Yingjie Zhang
Ni-rich layered oxides have become the main force of cathode materials for EV cells with high energy density owing to their satisfactory theoretical capacity, cost-effectiveness, and low toxicity. However, the high-voltage stability of Ni-rich cathode materials still has not fulfilled the demand of power batteries due to their intrinsic structural and electrochemical instability. The commonly used modification procedures are achieved via a wet process, which may lead to surface lithium-ion deficiency, phase change, and high costs during manufacturing. Herein, we construct a multifunctional Ti-based interfacial architecture on the surface of LiNi0.6Co0.2Mn0.2O2 (NCM) cathode materials via a novel dry interface modifying process in which no solvent is employed. The Ti-based interfacial architecture accelerates the transportation of lithium ions and consequently stabilizes the interfacial structure. This approach significantly improves the cycling stability in half cells, with a 15% increase in capacity retention over 100 cycles at 1 C under a high voltage of 4.5 V. Impressively, few internal cracks are observed in a modified sample after 500 times of charge and discharge between 2.75 and 4.35 V at 1 C rate, and the capacity retention can reach 93%.
✓ 已验证
DOI
高影响因子
Journal of Materials Chemistry A
·
2018
·Vol. 6
·期 48
·24920-24927
·
IF 9.931
Dong-Cheng Liu,Li-Ming Cao,Zhi-Mei Luo,Di-Chang Zhong,Jing-Bo Tan,Tong-Bu Lu
Engineering efficient and cost-effective electrocatalysts for the oxygen evolution reaction (OER) is an essential part of electrochemical water splitting. Herein, we report the in situ preparation of an efficient OER electrocatalyst CoFePi/Ni(PO3)2 on carbon cloth (CC) by decorating amorphous CoFe phosphate (CoFePi) on crystalline nickel phosphate (Ni(PO3)2). The as-synthesized hierarchically heterogeneous electrocatalyst can be directly used as a working electrode for the OER without extra substrates or binders. Electrocatalytic studies showed that the CoFePi/Ni(PO3)2/CC electrode displays excellent OER catalytic activity and stability. A current density of 10 mA cm−2 during the OER process can be achieved at a low overpotential of 213 mV in 1.0 M KOH solution, comparable to the results reported for the most efficient OER electrocatalysts. The ultrahigh oxygen evolution activity and high durability are ascribed to the unique 3D hierarchical heterogeneous nanostructure and in situ generated amorphous–crystalline composite, as well as the highly conductive substrate of CC, which endows the composite catalyst with sufficient active sites, strong structural stability and good electrical conductivity. This strategy offers a new direction to fabricate high-performance electrocatalysts for the oxygen evolution reaction.
✓ 已验证
DOI
高影响因子
Journal of Energy Storage
·
2023
·
IF 9.4
Yao Lu,Miaoyan Song,Jieyou Huang,Le Zhang,Binyu Zhao,Wenwei Wu,Xuehang Wu
Charging P2-type Na 0.66 Ni 0.33 Mn 0.67 O 2 (NNM) to a high upper cut-off voltage of 4.3 V (vs. Na + /Na) can yield a competitive discharge voltage (3.6 V-class) and capacity. However, achieving stable cycling for NNM under this condition remains challenging owing to an unfavorable phase transition and a large lattice-volume change. Herein, a dual-site doping strategy is used to simultaneously realize a pinning effect at the Na and transition metal sites. Incorporating pinned K + and Zn 2+ ions considerably enhances the structural stability of NNM, affording a complete single-phase reaction with ultralow strain (only 0.54 % variation in volume) during Na + insertion/extraction. The synergistic contributions of dual-site doping to the enhanced electronic conductivity , lowered Na + migration barrier, and increased Na + diffusion coefficients are confirmed via theoretical calculations. Consequently, the K + /Zn 2+ dual-site-doped Na 0.63 K 0.03 Ni 0.26 Zn 0.07 Mn 0.67 O 2 delivers satisfactory discharge capacities of 118.6 and 63.2 mAh g −1 at 10 and 2000 mA g −1 , respectively, and achieves an excellent capacity retention of 81.2 % after 200 cycles at 500 mA g −1 . This study provides a promising method to strengthen the stability of the Ni − Mn-based layered framework and optimize other high-voltage and high-capacity layered oxide cathode materials .
✓ 已验证
DOI
高影响因子
Nature Communications
·
2025
·Vol. 16
·期 1
·1-12
·
IF 15.7
Luo Jiayao,Guo Bangjun,Li Nana,Huang Qianjin,Wang Jingjing,Fu Yongzhu,Jia Linan,Zhang Xi,Hou Junbo,Zhu Jinhui,Zhuang Xiaodong
Coating Ni-rich layered oxide positive electrodes is essential to improve their electrochemical performance in sulfide-based all-solid-state Li batteries, but achieving cost-effective, high-performance positive electrodes remains challenging. In this work, we apply a thin (~3 nm) conductive binary Li borate glass coating (0.5Li 2 O·0.5B 2 O 3 ) onto single-crystal LiNi 0.8 Co 0.1 Mn 0.1 O 2 using a simple dry process and heating. This coated positive electrode delivers 209 mAh g −1 specific capacity at a specific current of 20 mA g −1 with 79.7% initial Coulombic efficiency, retains 87.8% capacity after 1000 cycles at a specific current of 200 mA g −1 , and achieves 14.6 mAh cm −2 areal capacity. Pouch cells with this positive electrode reach 383 Wh kg −1 specific energy, and sustain 300 cycles at a specific current of 66.67 mA g −1 . Various characterizations reveal that this coating can enhance Li-ion transport, stabilize the positive electrode lattice, and strengthen the interface between positive electrode and sulfide electrolyte. Here we show that conductive glass coatings enable high-voltage positive electrodes with high stability and specific energy in all-solid-state batteries.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2025
·
IF 13.2
Jiahui Liu,Hongchen Liu,Fan Yang,Junpu An,Siyuan Sun,Yang Sun,Kexin Wei,Xinyang Sun,Junwei Yuan,Meitong Zhao,Haojia Zhong,Kuobo Wang,Jintian Ren,Zhenxing Li,Yongfen Li
The electrochemical oxidation of biomass-derived 5-hydroxymethylfurfural (HMF) represents a promising pathway to synthesize the critical polymer monomer 2,5-furandicarboxylic acid (FDCA). However, the restricted adsorption of both HMF and OH − to the catalyst surface results in low activity and selectivity. To address this issue, this study introduced an electrochemically assisted strategy to synthesize Ni aerogel with Cu heteroatom doping (Ni 0.94 Cu 0.06 /NF), demonstrating excellent performance for HMF to FDCA conversion in alkaline media. The catalyst achieves 10 mA cm −2 at 1.307 V vs. RHE, with outstanding Hydrogen evolution reaction (HER) activity (10 mA cm −2 @11 mV). Notably, the conversion rate of HMF, the selectivity of FDCA and the Faraday efficiency can reach 99.5 %, 99 % and 97 %, respectively. Scanning Electron Microscope (SEM) and transmission electron microscopy (TEM) demonstrated that the aerogel's self-supported 3D framework with interwoven nanowire structure enables efficient exposure of catalytic sites. X-ray photoelectron spectroscopy (XPS) analysis further showed the modification with Cu forms unique Ni O Cu linkage within the catalyst's surface region, which effectively adjusts the electronic configuration of Ni sites and increases lattice oxygen content, thereby enhancing HMF adsorption. Density functional theory (DFT) revealed that the synergistic interplay between Ni and Cu markedly boosts the uptake capacity for both HMF and OH − , improves the rate-determining step (RDS) thermodynamics by reducing its barrier, and consequently accelerates the HMF oxidation reaction (HMFOR). Our findings elucidate fresh perspectives into the structure-performance relationship of nickel-based catalysts and offer a novel approach for designing advanced electrocatalysts for biomass upgrading.
✓ 已验证
产品关联
DOI
高影响因子
Journal of CO2 Utilization
·
2026
·
IF 8.6
Shuai Hu,Xiaoxuan Zhu,Yan Li,Yu Zhang,Bin Du,Jianjun Su,Yan Zhu,Zhenfeng Wang,Yanming Wang,Gewen Yu,Jian Ding,Yuqing Wang,Xiaohui Guo
Take into consideration the backdrop of global energy crisis and rising carbon dioxide concentration in the atmosphere, to research and develop efficient catalysts for converting CO 2 into sustainable energy is crucial. Based on this background, this study employed the complexation combustion method to prepare CuNi nanoclusters (NCs) with varying atomic ratios and applied in catalytic hydrogenation of CO 2 to CO or methanol. Through systematic characterization techniques such as XRD, SEM, BET, in-situ XPS, EPR, and chemisorption, the crystal phase structure, morphological features, physico-chemical properties, and catalytic performance of the as-obtained catalysts were thoroughly analyzed. The results of activity measurements demonstrate that the electronic synergy between CuNi bimetals exerts a positive catalytic effect on CO 2 hydrogenation to methanol. Notably, the Cu 1 Ni 1 catalyst achieved the striking methanol selectivity (98.5%) while maintaining a higher conversion of CO 2 (11.4%). Specifically, thanks to the employment of acetic acid complexation together with the isolation and stabilization effects of Ni species, a considerable amount of metastable Cu + is detected in the obtained catalyst as evidenced by XRD and in-situ XPS, which synergistically interacts with Cu 0 and facilitates the redox cycling of Cu active sites for CO 2 hydrogenation. Besides, the CO 2 -TPD and EPR show that a higher concentration of oxygen defects and the resulting large number of basic sites with moderate strength greatly facilitate the adsorption of CO 2 and hydrogenation to methanol; however, the excessively sites with strong basicity which present on the surface of Cu 0 Ni 1 generate the strong adsorption of CO 2 molecules, making the reaction route turned to the reverse water gas shift which is conducive to the hydrogenation of CO 2 to CO. Thus, the bond strength between CO 2 and basic site could alternate the mechanism of catalytic reaction on supported copper based catalysts.
✓ 已验证
产品关联
DOI
高影响因子
Joule
·
2026
·
IF 37.1
Bosheng Zhao,Dongsheng Ren,Deqing Li,Hongkun Pan,Yi Guo,Qianfan Pei,Xinyu Rui,Dechang Wang,Jinli Liu,Feixiong He,Peng Huang,Tiening Tan,Gaolong Zhu,Jianfeng Hua,Xiang Liu,Languang Lu,Minggao Ouyang
All-solid-state batteries (ASSBs) incorporating Ni-rich cathodes and sulfide solid electrolytes are promising for next-generation energy storage. However, their performance is constrained by the inherent electrochemo-mechanical instability and sluggish Li + diffusion kinetics in the randomly oriented Ni-rich cathodes. Herein, we present a microstructure-tailored Ni-rich cathode with fast Li + diffusion layer through regulation of primary particle size and distribution. Comprehensive investigations demonstrate that this optimized Ni-rich cathode enables rapid Li + transport kinetics and effectively accommodates strain accumulation during cycling. Furthermore, an in situ -formed Li 2 CO 3 coating on the cathode surface provides robust passivation against sulfide electrolyte decomposition at the interface. Consequently, sulfide-based ASSBs employing this Ni-rich cathode exhibit a high reversible capacity of 233.8 mAh g −1 and remarkable capacity retention of 79% after 1,000 cycles at 1 C and 71% after 10,000 cycles at 5 C. This work provides an effective and scalable strategy for designing high-performance Ni-rich cathodes, paving the way for high-energy-density and long-lifespan ASSBs.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Environmental Chemical Engineering
·
2026
·Vol. 14
·期 2
·122011
·
IF 7.5
Di Jin,Yunpeng Zou,Yang Zhao,Shuai Chen,Shiwei Luo,Taotao Chen,Jinchuan Zhang,Jialin Chen,Jijie Li,Yuewen Mu,Wen-Yan Zan,Fengwei Zhang
Transition metal-nitrogen-carbon (M-N-C) catalysts show great promise for converting CO₂ into valuable fuels and chemicals via electroreduction (CO₂RR). Nonetheless, controversy remains regarding which specific MNₓ coordination structure in M-N-C catalysts governs CO₂RR performance. We synthesized a series of Ni-NOMC catalysts with high specific surface area and varying NiN₃-Pyr site loadings using SBA-15 as a template, employing a small molecule condensation and pyrolysis strategy. Aberration-corrected scanning transmission electron microscopy (AC-STEM) and X-ray absorption spectroscopy (XAS) confirmed the presence of atomically dispersed Ni sites coordinated by pyrrolic nitrogen (NiN₃-Pyr). The Ni-NOMC-3 catalyst, with a higher NiN 3 -Pyr loading, achieved a remarkable CO Faraday efficiency (FE CO ) of 99.6% at −0.57 V vs. the reversible hydrogen electrode (RHE), while maintaining FE CO > 99% across a broad potential window (−0.17 to −0.97 V vs. RHE). Moreover, the ordered mesoporous structure of this catalyst enhances mass transport properties and optimizes active site accessibility, enabling a high CO partial current density of 157 mA·cm⁻² in a flow cell system. Theoretical simulations further reveal that the NiN₃-Pyr coordination structure exhibits superior catalytic performance for CO₂RR-to-CO compared to other possible NiN x configurations.
✓ 已验证
产品关联
DOI
高影响因子
FUEL
·
2026
·
IF 7.8
Bingshuo Li,Xinhang Lv,Tianhua Yang,Haijun Zhang,Xingping Kai,Rundong Li
Catalytic hydrodeoxygenation (HDO) is a promising strategy for upgrading phenolic bio-oil into cycloalkanes. Conventional catalysts often rely on strongly acidic supports, which tend to suffer from rapid deactivation. In this study, 4-ethylphenol was selected as a model compound derived from lignin bio-oil to investigate the effects of active sites on an inert support during the hydrogenation and deoxygenation of the phenolic group. Acid-site–support decoupling catalysts, denoted as Ni-HSiW/h-BN, were successfully prepared and were applied in the HDO of 4-ethylphenol to produce ethylcyclohexane. Using 0.5 g of 4-ethylphenol as the substrate and n-dodecane (30 mL) as solvent, the optimal reaction conditions were identified as a temperature of 300 °C, a reaction time of 3 h and the use of 15% Ni-HSiW 0.25 /h-BN catalyst. Under these conditions, complete conversion of 4-ethylphenol was achieved with 100% selectivity toward ethylcyclohexane. When the temperature was lowered to 180 °C and the reaction time reduced to 1 h using 15% Ni/h-BN, the main product shifted to ethylcyclohexanol with a selectivity of 94.4%. A reaction mechanism was proposed, indicating that the combination of Ni and HSiW synergistically enhances HDO efficiency.
✓ 已验证
产品关联
DOI
高影响因子