MICROPOROUS AND MESOPOROUS MATERIALS
·
2026
·
IF 4.5
Yutong Zou,Junbiao Wu,Meng Li,Gege Li,Yide Han,Yan Xu,Zhuopeng Wang
During the study of hydrothermal synthesis of nickel-encapsulated zeolite catalyst using the ligand-protection method, uniform nanofibers (∼10 nm diameter, hundreds of nanometers long) were unexpectedly observed on the surface of zeolite crystals. These nanofibers were subsequently synthesized independently outside the zeolite synthesis system and were identified as nickel-kerolite, a kind of talc-like nickel phyllosilicate. An optimal synthesis approach of the nickel phyllosilicate fibers was realized via a hydrothermal method using a synthetic gel comprising a silicon source, sodium hydroxide, nickel nitrate, and ethylenediamine (EDA). It is found that the formation of the unique fibrous morphology of nickel phyllosilicate requires a sufficiently strong alkaline medium and the presence of EDA. Ethylenediamine was proven to be essential for achieving the nano-fibrous morphology, probably due to the anisotropic growth inhibition from both EDA and its nickel complex (Ni-EDA), which restrict crystal development predominantly along one direction.
✓ 已验证
产品关联
DOI
高影响因子
FUEL
·
2026
·
IF 7.5
Haozhao He,Tao Wang,Qu Zhang,Bo Li,Xianze Wang,Wenyan Mu,Dongling Wu
The high content of heavy components in coal pyrolysis tar constrains its high-value utilization. Although semi-coke-based catalysts are cost-effective and promising for catalytic upgrading, their performance needs further enhancement. In this study, a novel nickel chloride-lactic acid (NiCl 2 -LA) deep eutectic solvent (DES) was designed. Leveraging nickel-lactic acid coordination and the inherent hydrogen bond network of DES, it penetrates semi-coke to promote nickel-semi-coke reactions, anchor nickel species with good dispersion, and finally synthesize nickel-supported semi-coke-based catalyst (Ni/C) via carbothermal reduction. Characterization results indicated that the Ni/C catalyst possesses a hierarchical pore architecture dominated by mesopores, with an increased specific surface area, enhanced degree of graphitization, and well-dispersed Ni nanoparticles on the semi-coke support. Based on this, during catalytic pyrolysis, the semi-coke support and well-dispersed Ni active sites exerted a synergistic effect, promoting the release of coal pyrolysis volatiles and increasing the tar yield from 8.30 % to 10.90 %. Simultaneously, by facilitating the cleavage of C–H and C–C bonds, they drove the conversion of heavy tar components to light components, elevating the relative content of monocyclic aromatic hydrocarbons from 1.16 % to 3.96 %. Moreover, the proportions of light components (BP ≤ 360 ℃) and light oil (BP ≤ 170 ℃) reached 62.60 % and 18.15 %, respectively, both at relatively high levels. This study validates that the functional properties of DES can be harnessed for the targeted design and preparation of high-activity catalysts, providing a viable strategy for the upgrading of light components in coal pyrolysis tar.
✓ 已验证
产品关联
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2026
·
IF 6.9
Meijing Lu,Junling Meng,Jingxuan Cao,Xiaotong Wang,Xiaoxue Han,Siqi Li,Jian Ren,Na Xu
Nanoarchitectures in catalyst design have garnered significant attention due to their ability to enhance performance, durability, and resistance against undesirable side reactions. In this work, an in situ exsolution method was employed to decorate the electrode surface with nanoparticles, aiming to enhance the electrochemical performance and long-term stability of the solid oxide fuel cells (SOFCs) anode. Initially, the Pr 0.8 La 0.2 Fe x Ni 1- x O 3- δ (PLFN, x = 0.4, 0.5) powders were synthesized and subsequently processed by in situ hydrogen reduction. Following the exsolution, characterization by Rietveld refinement of X-ray diffraction (XRD) patterns and high-resolution transmission electron microscopy (HRTEM) confirmed the formation of Fe-Ni alloy and LaFeO 3 particles. Correlation with electrochemical measurements revealed that the enhanced anode performance is primarily due to the surface Fe-Ni alloy nanoparticles. Furthermore, X-ray photoelectron spectroscopy (XPS) analysis verified the metallic state of the exsolved Fe and Ni species after reduction. Finally, the PLFN material was applied as an anode in an electrolyte-supported single cell, and Pr 0.8 La 0.2 Fe 0.4 Ni 0.6 O 3- δ (PLF 0.4 N 0.6 ) demonstrated superior output performance under different reduction temperatures. Meanwhile, the peak power densities with PLF 0.4 N 0.6 anode after in situ exsolution reached 1.04, 0.64, and 0.56 W cm −2 at 850 °C when using H 2 , NH 3 , and CH 4 as fuels, respectively, exhibiting remarkable fuel flexibility. Moreover, the single cell with PLF 0.4 N 0.6 as the anode exhibited excellent operational stability, showing a performance degradation rate of only 0.01% per hour over a 100-hour test. These results offer valuable insights into the rational design of next-generation SOFCs anodes possessing exceptional activity and durability.
✓ 已验证
产品关联
DOI
高影响因子
Progress in Natural Science-Materials International
·
2021
·Vol. 31
·期 1
·152-158
·
IF 3.607
Zhonghui Sun,Jia Zhou,Qingan Zhang
A new MgH 2 –PrF 3 –Al–Ni composite was prepared by ball milling under hydrogen atmosphere. After initial dehydrogenation and rehydrogenation, Pr 3 Al 11 , MgF 2 , PrH 3 and Mg 2 NiH 4 nanoparticles formed accompanying the main phase MgH 2 . The hydrogen absorption-desorption properties were measured by using a Sieverts-type apparatus. The results showed that the MgH 2 –PrF 3 –Al–Ni composite improved cycle stability and enhanced hydrogen desorption kinetics. The improvement of hydrogen absorption-desorption properties is ascribed to the synergetic effect of the in situ formed Pr 3 Al 11 , MgF 2 , PrH 3 and Mg 2 NiH 4 nanoparticles. This work provides an important inspiration for the improvement of hydrogen storage properties in Mg-based materials.
✓ 已验证
DOI
高影响因子
JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS
·
2026
·
IF 6.2
Zong-Pin Fu,Yun-Peng Zhao,Yu-Fa Wu,Qi-Jie Zhou,Shu-Ting Hu,Le-Le Qiu,Fang-Jing Liu,Mei Zhong,Jing Liang,Jing-Pei Cao
Mild thermal dissolution is an effective method for the clean, low-carbon conversion of lignite. However, the resulting products still contain numerous oxygen-bridged bonds and heavy molecular compounds, requiring further upgrading to serve as suitable feedstocks for fuels and chemicals. In this study, a supported Cu-Ni bimetallic catalyst was synthesized via a co-precipitation method and applied to the catalytic hydroconversion (CHC) of thermal dissolution portions from Zhaotong lignite (ZT) and lignite-related model compounds (LRMCs). Catalyst characterization revealed that metal particles were uniformly dispersed on the surface of the Cu-Ni/CoOx-CeO 2 catalyst, along with the formation of defect sites. The CoOx-CeO 2 support promoted surface oxygen vacancy formation. Furthermore, the incorporation of Ni altered the local coordination environment of Cu species through multicomponent interactions. The synergy between interfacial oxygen vacancies and Cu-Ni bimetallic sites significantly enhanced catalytic activity. Tests with LRMCs indicated that the Cu-Ni/CoOx-CeO 2 catalyst selectively cleaves C-O ether bonds under mild conditions, exhibiting both high selectivity and strong hydrogenation activity in the CHC of phenolic compounds. The catalyst also effectively promoted the CHC of macromolecular species in the soluble portion from ZT thermal dissolution, thereby converting phenolic compounds into cycloalkanol. These finding provides valuable insights for developing staged conversion routes and achieving value-added utilization of lignite.
✓ 已验证
产品关联
DOI
高影响因子
ENERGY & FUELS
·
2026
·
IF 5.3
Chuang Zhang,Yue Wang,Xin Hu,Wei Jiang,Xiao-Yan Zhao,Chen Xu Chen,Wen Li,Jing-Pei Cao
Selective hydrogenolysis of C–O bonds in lignin is widely regarded as the most promising strategy for generating high-value chemicals and clean liquid fuels. Ni–Ru bimetallic catalyst supported on solid superacid was successfully synthesized and applied to the cleavage of C–O bonds in diphenyl ether (DPE) and alkali lignin. The catalytic hydrogenolysis of DPE over a 10%Ni–0.5%Ru–S2O82–/ZrO2 catalyst produced 88.0% cyclohexanol. Additionally, 10%Ni–0.5%Ru–S2O82–/ZrO2 catalyzed the depolymerization of alkali lignin in high yields of phenolic compounds, primarily including guaiacol and methoxyphenol. The synergistic effect between Ni and Ru promoted electron transfer from Ni to Ru. The incorporation of Ru improved the dispersion of Ni and reduced the average particle size of metallic Ni. The strong acidity of the solid superacid support provided abundant acidic sites, facilitating hydrogen atom adsorption and thereby promoting C–O bonds cleavage.
✓ 已验证
产品关联
DOI
高影响因子
Materials Science and Engineering B-Advanced Functional Solid-State Materials
·
2026
·
IF 5.7
Adila Abulimiti,Yudong Zhang,Yiyuan Hua,Yanjun Miu,Tong Zhou,Xuejing Zhang,Can Cui,Weiji Dai,Cuijiao Zhao,Saifang Huang
Mg/Zr/Nb tri-doping jointly stabilizes Ni-rich layered cathodes under harsh operating conditions. • Tri-doping reduces Li + /Ni 2+ mixing and stabilizes the transition-metal layer and oxygen framework. • MZN-NCM delivers excellent cycling stability at room temperature, high temperature, and high cutoff voltage. • Mg/Zr/Nb co-doping improves charge transfer and Li + diffusion, enhancing the durability of Ni-rich cathodes. Ni-rich layered cathode materials (LiNi x M 1-x O 2 , x ≥ 0.8) offer high capacity and high energy density, but their cycling stability severely suffers from Li + /Ni 2+ cation mixing, H2-H3 phase-transition strain, interfacial side reactions, and sluggish Li + transport, especially under harsh conditions such as elevated temperature and high cutoff voltage. In this work, a Mg/Zr/Nb tri-doping strategy is proposed to construct Li(Ni 0.9 Co 0.05 Mn 0.05 ) 0.97 Zr 0.01 Mg 0.01 Nb 0.01 O 2 (MZN-NCM) cathode for synergistic stabilization under different operating conditions. The results show that Mg/Zr/Nb co-doping regulates the Ni valence distribution, reduces Li + /Ni 2+ cation mixing, enhances the stability of the transition-metal layer and oxygen framework, and suppresses interfacial side reactions and CEI degradation during cycling. MZN-NCM retains 90.1% of its capacity after 100 cycles at 25 °C and 89.8% at 60 °C, compared with only 59.8% and 41.7% for Pristine-NCM, respectively. Under a high cutoff voltage of 4.5 V, MZN-NCM also maintains a higher capacity retention of 87.7% after 100 cycles. Moreover, kinetic and interfacial chemical analyses indicate that multielement doping improves both charge-transfer behavior and Li + diffusion, enabling a synergistic enhancement of structural stability, interfacial stability, and ion transport. This work demonstrates that Mg/Zr/Nb synergistic doping is an effective material-design strategy for extending the applicable operating conditions of Ni-rich cathodes.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE
·
2026
·
IF 4.4
Li Xiaoguang,Chen Jia,Li Aoqi,Li Jing,Wang Mingyu,Li Liangsheng,Shangguan Enbo
A novel in situ self-sulfidation approach was devised to fabricate ZnO/ZnS/C ternary nanocomposites as highly stable anodes for alkaline Zn–Ni batteries. Zinc sulfate acted as a dual-purpose precursor, providing both zinc and sulfur, whereas acrylamide served as the carbon source and in situ reductant. In a single-step carbothermal pyrolysis at 800 °C, the carbon matrix converted sulfate ions to sulfide, facilitating the simultaneous generation of electrochemically active ZnO, a protective ZnS layer, and a conductive carbon network during a single thermal treatment. The optimized ZnO/ZnS/C-2 electrode exhibited a discharge capacity of 576.8 mAh g −1 after 600 cycles at 1 C and maintained 513.2 mAh g −1 at 15 C. Under identical conditions at 10C, the ZnO/ZnS/C-2 electrode delivered a capacity of 545.3 mAh g −1 , which is 41.5% higher than that of commercial ZnO (385.4 mAh g −1 ). Upon the current density reverting to 0.2 C, it regained 96.6% of its original capacity, indicating remarkable reversibility. Post-cycling scanning electron microscopy images validated the successful inhibition of zinc dendrite proliferation. The performance improvements arise from the synergistic combination of the protective ZnS layer, the interconnected conductive carbon framework, and the advantageous ZnO/ZnS heterointerface, which collectively boost structural stability and charge transfer kinetics.
✓ 已验证
产品关联
DOI
高影响因子
ACS Catalysis
·
2026
·
IF 13.6
Jiangtong Li,Ziyu Ye,Chi Zhang,Chiu Shek Wong,Tai-Sing Wu,Xiang-Yi Yang,Yun-Liang Soo,Negar Irandoust,Ziyi Meng,Vincent C.-C. Wang,Ye Zhu,Molly Meng-Jung Li
Dry reforming of methane (DRM) demands catalysts that simultaneously resist coking and sintering at high temperature. Here, we show that sodium aluminate (NaAlO2) acts as a highly effective interfacial modifier, creating a functional Ni−NaAlO2 metal−support contact that couples reaction-relevant CO2 retention with robust Ni stabilization. Temperature-programmed desorption reveals that NaAlO2 retains CO2-derived species up to 700 °C, driven by the strong basicity of its ionic Na−Al−O lattice, while structural analysis confirms strong interfacial metal−support coupling that preserves the size of metallic Ni. In situ spectroscopy reveals a bifunctional perimeter pathway under DRM conditions, where these CO2-derived oxygen-containing species hosted on NaAlO2 efficiently oxidize CHx intermediates generated on adjacent metallic Ni sites. These coupled interfacial functions enable stable, near-coke-free DRM operation with suppressed Ni sintering for 110 h on stream, drastically outperforming a reference Ni/Al2O3 catalyst that deactivates via severe sintering, coking, and reactor blockage within 24 h. Crucially, NaAlO2 dissolves in water and undergoes reversible hydration/dehydration, enabling uniform post-synthetic deposition onto pre-formed Ni catalysts via a simple aqueous impregnation−drying step. We demonstrate that this modular interface incorporation successfully upgrades both a commercial Ni reforming catalyst and a reference Ni/Al2O3 catalyst without rebuilding the parent catalyst structures, significantly improving their coke and sintering resistance. Overall, this work establishes NaAlO2 as a deployable interfacial modifier for coupled CO2 handling and metal stabilization in practical reforming applications.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2026
·
IF 9.6
Jiankun Li,Shang Wu,Quanlu Yang,Huize Zhang,Chenxu Zhu,Xiaoyi Meng,Xiaojun Yang,Qiong Su,Shuhe Kang,Juzhen Kang,Wei Lan
HS-FeNi-BNC is synthesized via B-bridging, with hollow porous carbon and Fe-B-Ni diatomic sites. • Fe-B-Ni bridge enables p-d hybridization to tune metal sites' electronic structures. • HS-FeNi-BNC delivers exceptional ORR/OER/HER electrocatalysis in alkaline media. • HS-FeNi-BNC-based ZABs operate from −10 to 60 °C with 92.9% Zn utilization efficiency. Rechargeable zinc-air batteries (ZABs) require efficient electrocatalysts to boost the sluggish oxygen reduction reaction (ORR)/ oxygen evolution reaction (OER) kinetics at the air cathode. However, designing high-activity catalysts faces considerable challenges due to spatial and electronic constraints. Herein, a boron-doped hollow spherical porous carbon (HS-FeNi-BNC) anchored with Fe-B-Ni diatomic sites is prepared via a facile B-bridging strategy, realizing the regulated construction of heteroatom doping and diatomic active sites. HS-FeNi-BNC possesses abundant micropores/mesopores, uniformly dispersed Fe Ni diatomic centers (0.27 nm spacing) with a Fe-B-Ni bridge structure, and topological carbon defects induced by B/N co-doping. HS-FeNi-BNC exhibits exceptional trifunctional electrocatalytic performance in alkaline electrolytes, with an ORR E 1/2 of 0.864 V, an OER overpotential of 308 mV and a hydrogen evolution reaction (HER) overpotential of 301 mV at 10 mA cm −2 . HS-FeNi-BNC-based ZABs achieve an outstanding wide-temperature operating range of −10 °C to 60 °C, a specific capacity of 761.51 mAh g −1 and a Zn utilization efficiency of 92.9%, outperforming Pt/C + RuO 2 -based ZABs. Density functional theory (DFT) calculations reveal that the Fe-B-Ni bridge structure triggers p-d orbital hybridization, regulating metal site electronic structures, optimizing reaction intermediate adsorption and accelerating interfacial electron transfer. This work advances the development of high-efficiency heteroatom-modified non-noble metal multifunctional catalysts. Download: Download high-res image (207KB) Download: Download full-size image
✓ 已验证
产品关联
DOI
PubMed
高影响因子
APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING
·
2026
·Vol. 132
·期 9
·968
·
IF 3
Shahbaz Muhammad Ali Hamza,Nasir Hamid,Afzal Amir Muhammad,Imran Muhammad,Chine Zied,Mumtaz Sohail,Kumar Abhinav,Kamran Muhammad Arshad
Developing multifunctional electrode materials that integrate high energy storage capacity with catalytic activity is essential for next-generation energy systems. Herein, a hierarchically engineered NiSnSe₂@r-GO@Ni-MOF composite was synthesized by the use of a two-step hydrothermal process, combining the high conductivity of r-GO, the porous framework of Ni-MOF, and the redox activity of NiSnSe₂. Structural and morphological investigations (SEM, XRD, Raman, XPS, and BET–BJH) confirmed the formation of a well-integrated mesoporous architecture with a large available electroactive sites and effective electron–ion transport. Electrochemical evaluation exhibited a high specific capacity of 1297.8 C g⁻¹. The assembled asymmetric device (NiSnSe₂@r-GO@Ni-MOF//AC) achieved an energy density of 44.8 Wh kg⁻¹ and a power density of 1120 W kg⁻¹, with 90% capacity retention over 7,000 cycles. Additionally, the composite exhibited excellent HER response and delivered a low overpotential of 49 mV and a Tafel slope of 52 mV dec⁻¹. The boosted bifunctional enactment is accredited to strong interfacial coupling and stabilizes the electrode structure, which highlights a scalable strategy for designing efficient multifunctional heterostructure to overcome the energy crisis in the present era.
✓ 已验证
DOI
高影响因子
ACS Applied Nano Materials
·
2026
·
IF 5.8
Cui Zhiqing,Wu Hao,Li Mingyue,Lv Liwei,Chen Huamao,Huang Jiawang,Li Taotao,Hu Jinwu,Fang Caihong
Exploration of efficient and nonprecious electrocatalysts
is essential
to propel water electrolysis toward developing a sustainable world.
Herein, we demonstrated heterogeneous Ni–NiWO 4 nanostructures
grown in situ on nickel foam (NF) (Ni–NiWO 4 /NF),
serving as effective bifunctional electrocatalysts toward the hydrogen
evolution reaction (HER) and urea oxidation reaction (UOR), enabling
high-performance overall urea splitting reaction (OUS) in both freshwater
and seawater. The favorable porous architecture provides a large electrochemically
active surface area and facilitates mass transfer. The coupling between
Ni nanoparticles and the NiWO 4 matrix creates an electron-rich
microenvironment and modulates the electronic states of the active
sites, which provides optimal chemical affinities for various reaction
intermediates, as confirmed by our calculation through density functional
theory calculations. Specifically, the Ni–NiWO 4 /NF
electrocatalyst exhibits low overpotentials of 26 mV@10 mA cm –2 , 126 mV@100 mA cm –2 , and 156 mV@200
mA cm –2 in alkaline freshwater and 31 mV@10 mA cm –2 , 162 mV@100 mA cm –2 , and 212 mV@200
mA cm –2 in alkaline seawater for the HER. Remarkably,
the overpotential is as low as 265 mV, even when the current density
was evaluated to be as high as 1.0 A cm –2 . For the
UOR, it demonstrates low potentials of 1.292 V@10 mA cm –2 , 1.343 V@100 mA cm –2 , and 1.374 V@200 mA cm –2 in alkaline freshwater and 1.307 V@10 mA cm –2 , 1.358 V@100 mA cm –2 , and 1.387 V@200 mA cm –2 in alkaline seawater. Notably, the recorded voltage
for the OUS reaction decreases to 1.366 V in freshwater and 1.390
V in seawater. Additionally, the catalyst demonstrates excellent long-term
stability in seawater for 100 h at 10 mA cm –2 . Furthermore,
we successfully demonstrated solar-powered green hydrogen production
at a rate exceeding 510 L h –1 m –2 , showcasing its strong potential for the practical application of
direct solar-to-hydrogen conversion.
✓ 已验证
DOI
高影响因子