文献检索

查找使用阿拉丁产品的科研文献

检索与阿拉丁产品相关的同行评审论文、DOI、PubMed 编号、期刊、作者、CAS 号及研究领域。

科研影响力快照

与阿拉丁产品相关的已发表科研成果

在搜索之前,这些指标可帮助访客快速了解产品关联科研的规模与质量。

347,389+ SCI 论文 与阿拉丁产品引用相关
2,303,681.05 总影响因子 匹配文献记录中影响因子的总和
81.20 最高期刊影响因子 匹配期刊中的最高 IF
6.63 平均期刊影响因子 匹配文献的平均 IF

参考指标 指标基于阿拉丁文献引用数据库及期刊影响因子记录。文献关联仅供科研参考,请以原始文献为准。

产品列表

视图 列表 网格

显示第3253至3264个,产品总数4,428个

切换升序
Ni
SEPARATION AND PURIFICATION TECHNOLOGY · 2022 · IF 9.136

Highly efficient recovery of hydrogen from dilute H2-streams using BaCe0.7Zr0.1Y0.2O3-δ/Ni-BaCe0.7Zr0.1Y0.2O3-δ dual-layer hollow fiber membrane

Furong Li,Gangxu Duan,Zhigang Wang,Dan Liu,Yifan Cui,Sibudjing Kawi,Shaomin Liu,Xiaoyao Tan

BaCe 0.7 Zr 0.1 Y 0.2 O 3-δ /Ni-BaCe 0.7 Zr 0.1 Y 0.2 O 3-δ dual-layer hollow fiber membranes are prepared by a co-spinning/co-sintering method, which is a simple and practical technique to integrate the electrolyte (BaCe 0.7 Zr 0.1 Y 0.2 O 3-δ ) and the electrode (Ni-BaCe 0.7 Zr 0.1 Y 0.2 O 3-δ ). A galvanic hydrogen pump is assembled by using this dual-layer hollow fiber membrane for hydrogen separation from dilute H 2 streams, in which the hydrogen permeation can be moderately controlled by the applied voltage. At 550℃ and 2 V voltage, a hydrogen flux of 2.15 mL·min −1 ·cm −2 and a hydrogen recovery rate of 81% are obtained when the feed is low concentration (13 vol%) H 2 stream. The one-step manufacturing method of integrating electrolytes and electrodes can be regarded as a more efficient method for the mass production of micro-tubular galvanic hydrogen pumps.

CAS / MDL: 1313-99-1
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
NEW JOURNAL OF CHEMISTRY · 2022 ·Vol. 46 ·期 8 ·3901-3908 · IF 3.925

Hydroisomerization of 1-octene utilizing hierarchical SAPO-11-supported Ni catalysts: effect of the alkyl chain length of the mesoporogen

Zhiping Chen,Li Liu,Faxiang Shi,Wenwu Zhou,Zhiyuan Yang,Anning Zhou

A series of hierarchical SAPO-11 molecular sieves synthesized by adding mesoporogens with different alkyl chain lengths were prepared. The synthesized hierarchical SAPO-11s were characterized by XRD, SEM, N2 adsorption–desorption, TEM, NH3-TPD and Py-IR. The results showed that the physicochemical properties of the hierarchical SAPO-11s change with the increase of the alkyl chain length, and the hierarchical SAPO-11 molecular sieve synthesized with DTAB has the largest external surface area and pore volume, and the most medium and strong B acid sites. Furthermore, the 1-octene hydroisomerization reaction on Ni catalysts supported on hierarchical SAPO-11 was investigated and the experimental results showed that the alkyl chain length of the mesoporogen has an obvious influence on the hydroisomerization selectivity. The hierarchical Ni/SAPO-11 catalyst synthesized using DTAB has the highest selectivity of C8 isomers and the lowest cracking selectivity. These results indicate that DTAB is the most suitable mesoporogen for the synthesis of hierarchical SAPO-11 molecular sieves for 1-octene hydroisomerization.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Catalysts · 2022 ·Vol. 12 ·期 5 ·509 · IF 4.501

Synergistic Effect between Ni and Ce Dual Active Centers Initiated by Activated Fullerene Soot for Electro-Fenton Degradation of Tetracycline

Chi Li,Yongfu Lian,Qin Zhou

The degradation of a high concentration of organic pollutants has long been a challenge to water restoration, and the development of electro-Fenton catalysis offers a practical approach to solving this problem. In this study, a novel electro-Fenton catalyst, activated fullerene soot-loaded NiO-doped CeO2(0.4(0.4NiO-CeO2)-AFS) nanoparticles, was prepared through the impregnation of 0.4NiO-CeO2particles and activated fullerene soot (AFS). When applied for the degradation of 200 mg/L of tetracycline, this catalyst demonstrated a degradation rate as high as 99%. Even after 20 cycles, the degradation rate was more than 80%. Moreover, it was concluded that AFS could initiate the synergistic effect between Ni and Ce dual active centers in the degradation of tetracycline; this can be ascribed to the extremely large specific surface area of AFS.Keywords:fullerene soot;NiO-doped CeO2;tetracycline;degrading efficiency;electro-Fenton

CAS / MDL: 75-65-0
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
FUEL · 2022 · IF 8.035

Experimental and DFT studies on diesel-steam-reforming to hydrogen over a bimetallic Rh–Ni-based MgO-Al2O3 microsphere catalyst

Qiangqiang Xue,Huilin Yi,Zhengwen Li,Zhao Jiang,Meng Chen,Yujun Wang,Binhang Yan,Guangsheng Luo

Surface modification of 600-µm-sized monodisperse gamma-alumina microspheres into magnesium–aluminum spinel, and co-impregnation-based loading of Rh–Ni (0.46 wt% Rh, 9.03 wt% Ni) were performed to synthesize catalysts for diesel-steam-reforming to hydrogen. The intimate interactions between Rh and Ni, the formation of the Rh–Ni alloy, and the Rh-doping-induced decrease in the particle size of Ni were determined. The DFT calculations results revealed that Rh-doped Ni(1   1   1) established remarkably weak bonds with oxygen-containing intermediates, and the reaction barrier of the rate-limiting step (CH 2 * + O* → CH 2 O*) on Rh–Ni(1   1   1) (0.76 eV) was lower than those of Ni(1   1   1) (1.14 eV) and Rh(1   1   1) (1.56 eV). The bimetallic catalyst shows the enhanced activity and resistance of sintering and carbon deposition compared with those of Ni-based (9.33 wt% Ni) and Rh-based (0.47 wt% Rh) catalysts. The catalytic performance of Rh–Ni-based catalyst was superior to that of physically mixed Ni-based and Rh-based catalysts at similar active metal loadings, which further confirmed the synergistic effect of Rh–Ni.

CAS / MDL: 13478-00-7 10139-58-9
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Reaction Kinetics Mechanisms and Catalysis · 2022 ·Vol. 135 ·期 3 ·1621-1634 · IF 1.843

Glucose-derived carbon-coated Ni–In intermetallic compounds for in situ aqueous phase selective hydrogenation of methyl palmitate to hexadecanol

Gu Xiaoyu,Shi Haonan,Wang Dandan,Chen Jixiang

The carbon-coated Ni (Ni@C) and Ni–In intermetallic compounds (IMCs) (Ni–In@C) catalysts were synthesized via combining one-pot hydrothermal method with glucose as carbon source and the carbonization under N 2 atmosphere. Their reactivities were compared in in situ aqueous phase selective hydrogenation of methyl palmitate to hexadecanol using methanol as a H 2 donor. The Ni@C catalyst dominatingly catalyzes decarbonylation/decarboxylation, accompanying with the serious C–C bond hydrogenolysis and methanation. In contrast, hexadecanol is mainly generated on Ni–In@C, where C–C bond hydrogenolysis and methanation are remarkably inhibited. This is ascribed to the geometric and electronic property of Ni–In IMCs. The hexadecanol yield reaches 84.0% under an optimal condition on Ni–In@C. The structure of NiIn IMC is hydrothermally stable even at 330 °C, and the Ni–In IMCs particles highly resist to sintering and leaching under harsh hydrothermal condition due to the confinement of carbon. Catalyst deactivation is mainly due to the carbonaceous deposition, and the catalyst reactivity is mostly recovered by the regeneration with CO 2 .

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Engineering · 2022 · IF 12.834

MOF-5@Ni Derived ZnO@Ni3ZnC0.7/PMS System for Organic Matter Removal: A Thorough Understanding of the Adsorption–Degradation Process

Youwen Shuai,Xue Huang,Benyin Zhang,Lu Xiang,Hao Xu,Qian Ye,Jinfeng Lu,Jing Zhang

The heterogeneous catalytic activation of peroxymonosulfate (PMS) for wastewater treatment is attracting increased research interest. Therefore, it is essential to find a sustainable, economical, and effective activated material for wastewater treatment. In this study, metal–organic framework (MOF)-5 was used as the precursor, and a stable and recyclable material ZnO@Ni 3 ZnC 0.7 that exhibited good adsorption and catalytic properties, was obtained by the addition of nickel and subsequent calcination. To investigate and optimize the practical application conditions, the elimination of rhodamine B (RhB) in water was selected as the model process. This study demonstrated that the degradation of organic matter in the system involved a coupling of the adsorption and degradation processes. Based on this, the mechanism of the entire process was proposed. The results of scanning electron microscopy, infrared spectrum analysis, and theoretical analysis confirmed that the van der Waals forces, electrostatic attraction, and hydrogen bonding influenced the adsorption process. Electron paramagnetic resonance analysis, masking experiments, and electrochemical tests conducted during the oxidative degradation process confirmed that the degradation mechanism of RhB included both radical and non-free radical pathways, and that the surface hydroxyl group was the key active site. The degradation of the adsorbed substrates enabled the regeneration of the active sites. The material regenerated using a simple method exhibited good efficiency for the removal of organic compounds in four-cycle tests. Moreover, this material can effectively remove a variety of organic pollutants, and can be easily recovered owing to its magnetic properties. The results demonstrated that the use of heterogeneous catalytic materials with good adsorption capacity could be an economical and beneficial strategy.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
COMPOSITES SCIENCE AND TECHNOLOGY · 2022 · IF 9.879

Absorption dominated high-performance electromagnetic interference shielding epoxy/functionalized reduced graphene oxide/Ni-chains microcellular foam with asymmetric conductive structure

Qiang Gao,Guangcheng Zhang,Yu Zhang,Xun Fan,Zhiwei Wang,Shuai Zhang,Ronglin Xiao,Fei Huang,Xuetao Shi,Jianbin Qin

In order to develop high-performance electromagnetic interference (EMI) shielding materials for the increasingly complex electromagnetic (EM) environment, in this work, the epoxy/functionalized reduced graphene oxide/Ni-chains microcellular foams with asymmetrical conductive structure (a-EP/f-RGO/Ni-chains microcellular foams) are prepared through a thermal compressing method and then followed by a supercritical carbon dioxide (scCO 2 ) foaming process. Benefiting from the construction of asymmetrical conductive structure which is assembled from the f-RGO-rich layer and Ni-chains-rich layer, the a-EP/f-RGO/Ni-chains microcellular foam with 5 vol% f-RGO and 5 vol% Ni-chains content exhibits better electrical conductivity of ∼10 −1  S/m and higher EMI shielding effectiveness (EMI SE) of 40.82 dB in X-band compared with the homogeneous conductive structured EP/f-RGO/Ni-chains (h-EP/f-RGO/Ni-chains) microcellular foam in same filler content . In addition, the maximum difference of reflection coefficient (R) up to ∼0.5 is achieved by actively regulating the EMI shielding process from reflection-absorption to absorption-reflection-reabsorption in different directions of EM wave incidence on the foams. Moreover, the compressive strength of microcellular foam is up to 24.58 MPa. Combined with excellent EMI shielding property and outstanding compressive property, the a-EP/f-RGO/Ni-chains microcellular foams prepared in this work display significant application advantages as high-performance EMI shielding materials.

CAS / MDL: 7791-20-0 1310-73-2
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
FUEL · 2022 · IF 8.035

Facile synthesis of N, P co-doped carbon encapsulated Ni catalyst for green production of cyclopentanone from biomass derivative furfural

Zhi Hu,Aidi Xie,Chun Chen,Zidan Zou,Yue Shen,Zhen Fu,Yunxia Zhang,Haimin Zhang,Huijun Zhao,Guozhong Wang

Aqueous-phase hydrogenation-rearrangement tandem (AP-HRT) reaction is a green and sustainable route to produce cyclopentanone from bio-based furan compounds. Herein, the ionic liquid was applied as the precursor to synthesize Ni@NP-C catalyst, which contains high dispersed nickel nanoparticles (Ni NPs) encapsulated in the N, P co-doped carbon layer , for the selectivity transformation of furfural towards cyclopentanone. The synthesized Ni@NP-C catalyst can afford 100% FAL conversion and 86.7% CPO yield at 130 °C and 1.5 MPa H 2 within 2 h AP-HRT reaction. The introduction of the electronegative heteroatom on the surface can not only improve the adsorption of reactant but also provide weak Lewis Acid sites for being beneficial to the high selectivity of cyclopentanone. The catalyst displays superior activity, selectivity, and stability in the tandem catalytic system in view of the tunable chemical states of the doped heteroatoms by handily adjusting the pyrolysis temperature.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
POWDER TECHNOLOGY · 2022 · IF 5.64

Preparation of isoelectric point-switchable polymer brush-grafted mesoporous silica using RAFT polymerization with high performance for Ni(II) adsorption

Yu Xing,Qian Li,Xiaoyi Chen,Miao Li,Shujing Wang,Yan Li,Tianyu Wang,Xitong Sun,Xianzhen Li

A series of polymer brushes were formed on the surface of mesoporous silica microspheres by copolymerizing 1-vinyl imidazole and acrylic acid through reversible-addition fragmentation chain transfer (RAFT) polymerization, with pI-switchable property and high grafting groups content. The resulting materials (SiO 2 @poly(VI- co -AA)) were then applied for removing Ni(II) from aqueous solution with a fast adsorption rate, and the maximum adsorption capacity was 62.81 mg/g. Significantly, the removal rate of 30 mg/L of Ni(II) could reach up to 99.40%, and the adsorbent also exhibited a good reusability, with the desorption efficiency of over 99%. Furthermore, the adsorption mechanism was supposed to be electrostatic interaction and complexation characterized by Zeta potentials and XPS . It implied that the SiO 2 @poly(VI- co -AA) microspheres could be considered as a potential adsorbent for removing Ni(II) from wastewater, and was expected to expand its application to remove other heavy metals and dyes.

CAS / MDL: 79-10-7 1072-63-5
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
SURFACE & COATINGS TECHNOLOGY · 2022 · IF 4.865

Investigation of the anti-corrosion performance of a Cu/Ni–B4C superhydrophobic coating with self-cleaning and abrasion resistance properties

Shuhan Dong,Yang Yang,Ruina Ma,An Du,Mingxu Yang,Yongzhe Fan,Xue Zhao,Xiaoming Cao

A Cu/Ni–B 4 C superhydrophobic coating was fabricated on the surface of Q235 steel under different current density via electrodeposition . The distribution of electric field influenced by current density controls the growth of rough structure. Therefore, the effect of current density was measured by the morphology and wettability of coating and analyzed by Electric field distribution model. The coating surface demonstrates the most uniform and compact rough structure at a current density of 3 A/dm 2 (M C-3 ) obtaining contact angle 160 ± 2° after the surface energy reduced by stearic acid. The self-cleaning performance and mechanical stability of M C-3 coating were studied. The potentiodynamic polarization curve (PPC) and electrochemical impedance spectroscopy (EIS) were used to measure the anti-corrosion and protection performance of the coatings with different morphology and contact angle. The protective performance of M C-3 coating soaked in 3.5 wt% NaCl solution for different time was studied by EIS. The wetting stability of different coatings was studied by single frequency impedance spectroscopy. Then the double protective mechanism of superhydrophobic coating was described and the corresponding model was established.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH · 2022 · IF 4.326

Structure Evolution of Ni–Cu Bimetallic Catalysts Derived from Layered Double Hydroxides for Selective Hydrogenation of Furfural to Tetrahydrofurfuryl Alcohol

Xiao Chen,Wenqi Liu,Jingjie Luo,Hongyu Niu,Rongrong Li,Changhai Liang

The hydrogenation of furfural containing multifunctional group often needs the high-efficiency cooperation of multiple catalytic active centers, which is greatly determined by the regulation of the surface and interface structure of multicomponent catalytic materials. Based on such circumstance, a series of highly dispersed supported bimetallic Cu–Ni catalysts prepared by the in situ topological transformation of layered double hydroxides have been investigated for the one-pot hydrogenation of furfural. Compared with the supported monometallic Cu and Ni catalysts, the optimized bimetallic Cu1Ni3/MgAlO catalyst presents highly efficient and good selectivity in the hydrogenation of furfural at the bath reactor. The selectivity to tetrahydrofurfuryl alcohol reaches 94.0% with a complete conversion of furfural at 110 °C under 3 MPa of H2 for 3 h. The results of TEM and in situ FT-IR confirm that the Ni-rich Cu–Ni alloy in the Cu1Ni3/MgAlO catalyst generates a strong synergistic effect, which shifts the adsorption configuration of furfural from parallel or vertical adsorption to tilted adsorption so as to significantly improve the catalytic performance. The intrinsic catalytic performances of CuxNiy/MgAlO catalysts indicate that the TOFC═O and TOFC═C values can be balanced through construction of the structure of the catalyst for achieving the synergistic effect between Cu and Ni significantly to enhance the one-pot selective hydrogenation of furfural to tetrahydrofurfuryl alcohol. Additionally, the Cu1Ni3/MgAlO catalyst presents excellent reusability by six-cycle testing. The above results indicate that the Cu1Ni3/MgAlO with the cooperation of multiple catalytic active centers is a promising catalyst for the selective hydrogenation of furfural.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
APPLIED ORGANOMETALLIC CHEMISTRY · 2022 ·Vol. 36 ·期 10 ·e6833 · IF 4.072

Synthesis, structure, and anticancer studies of Cu (II) and Ni (II) complexes based on (5-chlorosalicylaldehyde)-4-aminoantipyrine Schiff base

Jing Hu,Yun Luo,Min Hou,Jia Jia Qi,Li Li Liang,Wen Ge Li

Two dinuclear complexes [Cu 2 (LO) 2 ] and [Ni 2 L 2 Cl 2 (C 2 H 5 OH) 2 ] derived from (5-chlorosalicylaldehyde)-4-aminoantipyrine (HL) were synthesized and characterized by infrared (IR) spectroscopy,thermogravimetric analysis, and powder X-ray diffraction. Molecular structures of the Cu (II) and Ni (II) complexes were determined by single-crystal X-ray diffraction. Their cytotoxicity was evaluated by methyl thiazolyl tetrazolium assay against human tumor cells, such as lung carcinoma A549, lung adenocarcinoma H1975, breast carcinoma MDA-MB-231, and nasopharyngeal carcinoma CNE-2Z cell lines. The results showed that the Cu (II) complex had much better anticancer activity than the Ni (II) complex, especially for MDA-MB-231 and CNE-2Z cells. The reason may be that they have different structures. The methyl group on the (5-chlorosalicylaldehyde)-4-aminoantipyrine (HL) was oxidized to the hydroxymethyl group, herein, namely LO, which is difficult to achieve in the normal chemical synthesis process. However, we did it by a solvothermal method at low temperature. It provides a new way of thinking and synthesis. The anticancer activity of the copper complex was next only to cisplatin, and the copper complex was nontoxic for the human normal cell lines. The experiment results also showed that the copper complex could inhibit tumor cell proliferation through the cell cycle and cell apoptosis.

CAS / MDL: 83-07-8 635-93-8
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
已复制

文献关联基于可获得的产品、CAS、DOI 及引用记录。收录不代表作者或出版方对阿拉丁产品的背书,请以原始文献为准。