Nature Energy
·
2022
·Vol. 7
·期 9
·866-875
·
IF 67.439
Zhai Shuo,Xie Heping,Cui Peng,Guan Daqin,Wang Jian,Zhao Siyuan,Chen Bin,Song Yufei,Shao Zongping,Ni Meng
Improved, highly active cathode materials are needed to promote the commercialization of ceramic fuel cell technology. However, the conventional trial-and-error process of material design, characterization and testing can make for a long and complex research cycle. Here we demonstrate an experimentally validated machine-learning-driven approach to accelerate the discovery of efficient oxygen reduction electrodes, where the ionic Lewis acid strength (ISA) is introduced as an effective physical descriptor for the oxygen reduction reaction activity of perovskite oxides. Four oxides, screened from 6,871 distinct perovskite compositions, are successfully synthesized and confirmed to have superior activity metrics. Experimental characterization reveals that decreased A-site and increased B-site ISAs in perovskite oxides considerably improve the surface exchange kinetics. Theoretical calculations indicate such improved activity is mainly attributed to the shift of electron pairs caused by polarization distribution of ISAs at sites A and B, which greatly reduces oxygen vacancy formation energy and migration barrier.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2022
·Vol. 33
·期 27
·21713-21726
·
IF 2.779
Zeng Jinling,Xu Yiwen,Li Liangjie,Wang Wenwei,Yao Yingbang
In this work, calcium barium zirconate titanate piezoelectric ceramics 0.4Ba(Zr 0.2 Ti 0.8 )O 3 - 0.6(Ba 0.7 Ca 0.3 )TiO 3 ((1− x )BZT- x BCT, abbreviated as x BCZT, x = 0.6) were prepared by conventional solid state reaction method. Different surfactant additives (SDS, CTAB, PEG, and Tris–HCl, respectively) were added to the ball milling process before sintering. Meanwhile, the temperature and dwelling time during the sintering process were also systematically investigated. Their effects on the microstructural, electrical, and piezoelectric properties of the modified ceramics were investigated. It was found that with the Tris–HCl surfactant, the dispersion of the 0.6 BCZT ceramics was the best, and the average particle size was ~82 nm. By using the SDS surfactant, the ceramics showed the highest relative density, i.e., 97%. For the ferroelectric performances, the largest coercive field ( E c = 5.39 kV/cm) was observed in the sample using the SDS surfactant when the sample was sintered at 1300 °C for 6 h. For the dielectric performances, the largest dielectric constant ( ε ) was found to be 35,366.9 for the sample using CTAB surfactant and sintered at 1300 °C for 4 h. We discovered that CTAB-modified ceramics sintered at 1290 °C for 2 h had the highest maximum polarization P s = 24.975 kV/cm and remnant polarization P r = 8.200 kV/cm and sintered at 1300 °C for 4 h produced the highest piezoelectric constant d 33 and dielectric constant of 94 pC/N and 35,366.7, respectively.
✓ 已验证
产品关联
DOI
高影响因子
Molecular & Cellular Toxicology
·
2022
·Vol. 19
·期 3
·551-564
·
IF 1.718
Cheng Weina,Chen Qihong,Wang Xiaoning,Liu Liu,Li Xiaofei,Duan Cancan,Zhang Jianyong
Background Norcantharidin (NCTD) has multiple antitumor effects. However, NCTD can induce significant hepatotoxicity and the mechanism of hepatotoxicity is not clear for now. Objective This study aimed to explore the hepatotoxicity of NCTD in rat by ultra-performance liquid chromatography (UPLC) quadrupole time-of-flight (Q-TOF)-MS (UPLC/Q-TOF-MS) metabolomics. Results Serum biochemical indices including alanine aminotransferase (ALT) and total bilirubin (T-BIL) were significantly increased. Histopathological and ultrastructure results revealed that hepatocytes were damaged. Furthermore, the metabolomics results showed that 11 metabolites in serum and 8 metabolites in liver were differential metabolites for NCTD hepatotoxicity. Four metabolic pathways including the sphingolipid metabolism, purine metabolism, arachidonic acid metabolism, and glycerophospholipid metabolism were the key metabolic pathways related to NCTD hepatotoxicity. Conclusion The metabolomics analysis in this study reveal new clues on the hepatotoxicity mechanism of NCTD in rats. These findings have potential applications in the toxicity study of NCTD.
✓ 已验证
DOI
高影响因子
CELL AND TISSUE RESEARCH
·
2022
·Vol. 390
·期 2
·293-313
·
IF 4.051
Li Zhen-Fang,Hao Shuang-Li,Wang Lan-Min,Qi Hong-Yu,Wang Jia-Ming,Tan Fu-Qing,Yang Wan-Xi
Spermatogenesis is a finely regulated process of germ cell proliferation and differentiation that leads to the production of sperm in seminiferous tubules. Although the mammalian target of rapamycin (mTOR) signaling pathway is crucial for spermatogenesis in mammals, its functions and molecular mechanisms in spermatogenesis remain largely unknown in nonmammalian species, particularly in Crustacea. In this study, we first identified es-Raptor (the core component of mTOR complex 1) and es-Rictor (the core component of mTOR complex 2) from the testis of Eriocheir sinensis . Dynamic localization of es-Raptor and es-Rictor implied that these proteins were indispensable for the spermatogenesis of E. sinensis. Furthermore, es-Raptor and es-Rictor knockdown results showed that the mature sperm failed to be released, causing almost empty lumens in the testis. We investigated the reasons for these effects and found that the actin-based cytoskeleton was disrupted in the knockdown groups. In addition, the integrity of the testis barrier (similar to the blood-testis barrier in mammals) was impaired and affected the expression of cell junction proteins. Further study revealed that es-Raptor and es-Rictor may regulate spermatogenesis via both mTORC1- and mTORC2-dependent mechanisms that involve es-rpS6 and es-Akt/es-PKC, respectively. Moreover, to explore the testis barrier in E. sinensis , we established a cadmium chloride (CdCl 2 )–induced testis barrier damage model as a positive control. Morphological and immunofluorescence results were similar to those of the es-Raptor and es-Rictor knockdown groups. Altogether, es-Raptor and es-Rictor were important for spermatogenesis through maintenance of the actin filament network and cell junctions in E. sinensis.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ANALYTICAL SCIENCES
·
2022
·Vol. 39
·期 1
·13-22
·
IF 1.967
Chen Xianli,Liu Yi,Zhong Ming,Yang Jiangyong,Lin Zhenming,Liang Yong
Sialic acid (SA), known as N -acetyl neuraminic acid, is a natural 9-carbomonosaccharide derivative. SA has been widely applied in the early diagnosis of diseases as therapeutic target. However, the abundance of SA is very low in biological samples, which is usually interfered by the similar molecules coexisting at high abundance. Combining the advantages of high selectivity and specificity of molecularly imprinted technology, high specific surface area of mesoporous materials and excellent optical properties of quantum dots, we chose Mn-doped ZnS quantum dots as signal elements, and sialic acid as the template molecule. KH-4-MAPB with recognition ability to SA was synthesized by one-step hydrothermal method using thiolene click reaction as functional monomer. Based on the principle of boron affinity, molecularly imprinted polymers with highly ordered mesoporous structure were prepared, and the structure and fluorescence properties of fluorescent molecularly imprinted polymers were studied. FT-IR, XRD, TEM and nitrogen adsorption–desorption experiments were used to characterize the structure and morphology of the molecularly imprinted polymers. The results showed that the prepared molecularly imprinted polymers had highly ordered mesoporous structure and a large number of imprinted holes, which ensured the specific selectivity of the molecularly imprinted polymers. The fluorescence properties of MIMPs were characterized and analyzed by fluorescence spectra, equilibrium adsorption kinetics experiments were conducted and imprinting properties were recorded under different pH. The above experimental results showed that the fluorescence quenching was successfully achieved when the template molecule SA was captured by the molecularly imprinted polymer. When the concentration of SA was 1.25–100 × 10 –2 g/L, the fluorescence quenching degree of MIMPs showed a fine linear relationship with SA. The correlation coefficient was 0.9946, and the detection equation was F 0 / F − 1 = 0.0215 [CSA] + 0.0241. MIMPs had a high recognition ability for SA, and the imprinting factor was 2.44. As a fluorescent sensor for SA, the response time of MIMPs was 20 min. When the buffer solution pH was 7, the imprinting factor was the largest. Under the best conditions, MIMPs revealed good selectivity and specificity for the fluorescence recognition of SA. MIMPS were also applied to the analysis of SA in real human serum samples with satisfactory results. Graphical abstract
✓ 已验证
DOI
PubMed
高影响因子
Science China-Technological Sciences
·
2022
·Vol. 65
·期 11
·2675-2686
·
IF 3.903
Han GaoJie,Xue PeiWen,Cai ZhengHao,Feng YueZhan,Liu ChunTai,Shen ChangYu
Two-dimensional (2D) boron nitride nanosheet (BNNS) is promising in polymer-based thermal management materials (TMMs) by pre-constructing three-dimensional (3D) thermally conductive skeleton, but it yet suffers from the challenges of high-effective exfoliation and affinitive compatibility with matrix. In this work, we developed a one-step exfoliation and deprotonation approach by the high-effective ball milling technique to prepare aramid nanofiber (ANF)/BNNS suspension. Under the strong collision/shear effect of ball-milling, micron-level hBN sheets were exfoliated into smaller and thinner BNNS with edge functional groups, meanwhile, poly-p-phenylene terephthalamide (PPTA) fibers were split into ANF by dissociating the intermolecular hydrogen bonds. More importantly, both the exfoliation and deprotonation could be accelerated by each other to achieve a 100% yield of ANF/BNNS suspension with strong hydrogen/covalent bonding interactions between them. Subsequently, the prepared ANF/BNNS suspension was used to construct 3D vertically aligned ANF/BNNS skeleton by the unidirectional freezing method. The obtained epoxy-based composite (EP/ANF/BNNS) revealed excellent thermal conductivity of 2.41 Wm −1 K −1 at 14.9 vol% BNNS loading due to the vertically oriented heat conduction paths and low interfacial thermal resistance in the skeleton. Moreover, EP/ANF/BNNS composite showed high thermal stability and extraordinary fire retardancy with dramatically decreased heat release rate (265 W g −1 ) and total heat release (20.6 kJ g −1 ). Therefore, this work demonstrates a high-efficient one-step ball-milling exfoliation and deprotonation technique for preparing ANF/BNNS suspension, which reveals an enormous potential in preparing advanced TMMs by constructing 3D thermally conductive skeletons.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE
·
2022
·Vol. 57
·期 36
·17481-17490
·
IF 4.682
Mo Peicheng,Chen Jiarong,Chen Chao,Hu Qiaofan,Pan Xiaoyi,Xiao Leyin,Lin Feng
Polycrystalline cubic boron nitride (PCBN) was synthesized at high temperature and ultra-high pressure, using cBN, TiN, AlN and Ti as starting materials. The effects of CBN content (48–63 wt%) and sintering temperature (1300–1600 °C) on the composition, microstructure and mechanical properties of PCBN materials were studied. X-ray diffraction and scanning electron microscope were used to analyze the phase composition, microstructure and surface crack morphology of PCBN. At the same time, the compactness, microhardness, fracture toughness and flexural strength of PCBN were tested. Research shows that the phase components of PCBN samples are mainly composed of BN, TiB 2 , TiN and AlN. Almost all Ti reacts with cBN during the sintering process to form TiN and TiB 2 phases. When the sintering temperature is 1500 °C, the reaction has been fully completed. When the cBN content increases from 48 to 63 wt%, the relative density, flexural strength and hardness of PCBN increase with the increase in cBN content. When sintered at 1500 °C and the cBN content is 63 wt%, the relative density, flexural strength, fracture toughness and microhardness of the composite are 99%, 820.8 MPa, 6.6 MPa.m 1/2 and 3362 Hv, respectively.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Oceanology and Limnology
·
2022
·Vol. 41
·期 1
·300-313
·
IF 1.554
Ke Songze,Zhang Bo,Yu Yanlei,Wang Sijia,Jin Weihua,Wu Jian,Chen Jianwei,Zhang Huawei,Wei Bin,Wang Hong
A sulfated galactofucan designated as UpG was obtained from the brown algae Undaria pinnatifida by calcium chloride extraction. Chemical analyses showed that UpG is composed of galactose and fucose at a high sulfation level. Low-molecular weight UpGP-0.5 was prepared from UpG through acid hydrolysis for structure characterization. The backbones of UpG are determined to be α-(1,3)-Fuc, α-(1,4)-Gal, α-(1,3)-Gal, and α-(1,6)-Gal by GC-MS, FT-IR, NMR, and LC-MS analyses. Sulfate groups are modified at C2 and/or C4 of fucose and C3 and/or C4 of galactose. UpG could partially lower blood sugar and serum lipid levels in type 2 diabetic mice. Moreover, UpG treatment regulates the abundance of some specific gut microbiota, such as enriching the abundance of Muribaculum and Christensenellaceae, and reducing that of Bilophila , Tannerellaceae, Candidatus Saccharimonas and Anaerotruncus . The findings characterized the detailed structure of a sulfated galactofucan and investigated its potential for the treatment of type 2 diabetes mellitus.
✓ 已验证
产品关联
DOI
高影响因子
ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH
·
2022
·Vol. 30
·期 10
·27315-27327
·
IF 5.19
Zhu Yating,Shen Jia,Guo Manli,Zheng Haoling,Cao Yujuan
In this work, nitrogen-doped magnetic porous carbon material (N-MPC) was prepared through the high-temperature calcination of low-cost [Fe(CN) 6 ] 3− -loaded anion-exchange resin, which was experimentally demonstrated to have significant adsorption performance for tetracycline (TC) in water. The N-MPC adsorbent with a large specific surface area (781.1 m 2 g −1 ) was able to maintain excellent performance in a wide pH range from 4 to 10 or in high ionic strength solution. The adsorption of TC on N-MPC was found to be more consistent with the pseudo-second-order model and Langmuir adsorption model, and the maximum adsorption capacity ( q m, cal ) was calculated to be 603.4 mg g −1 . As a recoverable magnetic adsorbent, the N-MPC remained a TC removal rate higher than 70% after four adsorption cycles. The adsorption mechanism was speculated on the basis of characterizations, where pore filling, hydrogen bonding interaction, and π-π electron donor–acceptor (EDA) interaction were crucial adsorption mechanisms. A variety of antibiotics were selected for adsorption, and excellent performance was found especially for TCs, indicating that the N-MPC can be used for the efficient removal of TCs from water.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH
·
2022
·Vol. 30
·期 10
·27357-27371
·
IF 5.19
Ma Qing-guang,Wan Yi-ping,Liu Ze-hua,Dang Zhi
Analytical method for three natural estrogens (NEs) and their sulfate and glucuronide conjugates in waste and river waters using solid-phase extraction (SPE) coupled with ultra-performance liquid chromatography tandem mass spectrometry (UPLC-MS/MS) has been available, but problems including poor recovery exist. In order to solve these, some optimizations have been performed in this work. For sample preparation, both rinse and elution solutions were optimized, in which 6 mL of MeOH/water (1:9, v/v), MeOH/Ace/water (10:2:88, v/v/v), and MeOH/NH 4 OH/water (10:2:88, v/v/v) were determined as the rinse solution, while 6 mL of 2.0% NH 4 OH/MeOH was determined as the elution solution for conjugated NEs (C-NEs). For mobile phase, addition of NH 4 F could obviously enhance the signal response of the nine target compounds, and the optimized addition concentration was 0.5 mmol/L. The developed efficient method was validated and showed excellent linearity for each target compound ( R 2 > 0.998), low limit of quantifications (LOQs, 0.07–1.29 ng/L) in four different water matrices, and excellent recovery efficiencies of 81.0–116.1% in influent, effluent, ultra-pure, and river water samples with low relative standard deviations (RSDs, 0.6–13.6%). The optimized method was successfully applied to influent, effluent, and Pearl River water, among which three NEs were all detected, while five C-NEs were found in the influent, three C-NEs were detected in the effluent, and two C-NEs were found in the Pearl River water, indicating the wide distribution of NEs and C-NEs in different water environments. This work provided a reliable and efficient analytical method for simultaneous trace determination of NEs and C-NEs, which had satisfactory absolute recoveries with low RSDs, low LOQs, and time-saving for both analysis and nitrogen drying.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Cell Death & Disease
·
2022
·Vol. 13
·期 11
·1-13
·
IF 9.685
Chen Shiyu,Cai Kun,Zheng Dijie,Liu Yanqing,Li Lin,He Zhiwei,Sun Chengyi,Yu Chao
Pancreatic cancer (PC) is one of the most malignant types of cancer, and is characterized by early metastasis, limited response to chemotherapeutics, and poor prognosis. Therefore, there is an urgent need to explore new therapeutic strategies for PC treatment. Human rhomboid-like 2 (RHBDL2) is differentially expressed in cervical and breast cancer. However, the correlation between RHBDL2 and PC remains unclear. We found that RHBDL2 is highly expressed in human PC cells and tissues and is significantly associated with distant metastasis and poor survival of patients with PC. Gain- and loss-of-function assays indicated that RHBDL2 could accelerate PC cell proliferation and mobility in vitro and in vivo. The RNA-Seq results suggest that RHBDL2 may be involved in the activation of Notch signaling pathway. IMR-1 could restore the proliferation and metastatic capacity of PC cells mediated by RHBDL2. RHBDL2 interacted with and cleaved Notch1, resulting in the release of N1ICD. RHBDL2 decreased the ubiquitination level of N1ICD and collaborated with Ovarian tumor domain-containing 7B (OTUD7B) to stabilize N1ICD via the ubiquitin-proteasome pathway. RHBDL2 facilitated PC cell proliferation and mobility by stabilizing the N1ICD via the OTUD7B and activating the Notch signaling pathway. Thus, targeting this novel pathway may be a potential therapeutic strategy for PC.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Science China-Technological Sciences
·
2022
·Vol. 65
·期 12
·2979-2989
·
IF 3.903
Jin JiaSheng,Xia Wei,Hu Pan,Yang Hu
Algae and suspended colloidal particles produced high turbidity in water, weakened water purification, and threatened the safety of the water supply. In this study, a series of composite coagulants (atp-st-CTA) composed of a cationic starch (st-CTA) and attapulgite (ATP) with different fed mass ratios were fabricated by a simple method to coagulate kaolin suspension with initial turbidity of 80.0 NTU and Chlorella suspension with 0.25 mg/L of chlorophyll a ( chla ), respectively. Fourier transform infrared spectroscopy and scanning electron microscopy investigated the structural characteristics of atp-st-CTA. The maximum turbidity and chla removal rates of atp-st-CTA were 92.2% and 100.0%, respectively, at natural pH conditions. The effects of the fed mass ratio of st-CTA to ATP in the composites, dose, pH, and coexisting humic acid on the coagulation performance of atp-st-CTA were comprehensively investigated. Based on the apparent coagulation behaviors, the zeta potentials of the supernatants after coagulation, and the flocs properties, the coagulation mechanisms of atp-st-CTA were discussed in detail. The complete charge neutralization due to st-CTA and the enhanced sedimentation by ATP synergistically removed turbidity and algae from the water efficiently. In short, atp-st-CTA as a talented material has a notable prospect in applications of water treatment owing to its advantages of environmental friendliness, low cost, and high efficiency.
✓ 已验证
产品关联
DOI
高影响因子