International Journal of Environmental Science and Technology
·
2025
·
IF 3.4
Hossain M. F.,Akther N.,Lu J.,Duan C.,Khan M. T.,Munyaneza J.,Zhou Y.
High adsorption efficiency, synchronized removal of anionic and cationic dyes, and adsorbent recyclability are three contemporary challenges in treating wastewater generated during dyeing operations. In this study, citric acid (CA) and polyethylenimine (PEI) co-functionalized cellulose adsorbent (CS-CA/PEI) with an elevated density of amino and carboxyl functional groups were synthesized using two-step simple methods. CS-CA/PEI with double-network exhibited high electrostatic affinity for both anionic (methyl orange, MO, sunset yellow, SY) and cationic (methylene blue, MB and victoria blue B, VB) dyes over a pH range. The fitted adsorption capacities of CS-CA/PEI for MB, MO, VB and SY were 134.58 mg/g (0.42 mmol/g), 3792.59 mg/g (11.58 mmol/g), 124.53 mg/g (0.24 mmol/g) and 215.51 mg/g (0.47 mmol/g), respectively, outperforming the majority of the reported adsorbents. Langmuir isotherm and pseudo-second order kinetic model established better correlation with experimental data, representing single-layered adsorption through strong electrostatic interactions. CS-CA/PEI performed better in binary pollutants system than in single system, with binary adsorption capacity for MB, MO, VB, and SY being 56%, 7%, 128%, and 14% higher, respectively, demonstrating synergism between dyes and adsorbents. After four repeated adsorption–desorption cycles, CS-CA/PEI showed good structural stability and recyclability, with > 90% of the initial adsorption efficiency for MB and VB and > 70% for MO and SY. Therefore, CS-CA/PEI, with excellent adsorption performance in single and binary pollutant systems, high recyclability, and ease of separation, has significant application potential in treating dyeing wastewater. Graphical
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2025
·
IF 9
Sikai Chen,Jinglin Yuan,Peng Lin,Yi Jin,Han Zhang
Facing the sustainability and potential environmental risk of polyacrylamide (PAM), an both effective and environmentally friendly cationic PAM-grafted cellulose nanofibers (CNFs) flocculant were developed. The preparation was accomplished by grafting acrylamide (AM) and 2-(acryloyloxy)ethyl)trimethylammonium chloride (DAC) from CNF, whereby Cu(0)-mediated reversible deactivation radical polymerization was utilized. Important aspects of the surface-grafted CNFs, including their positive charge concentration and the density and length of the grafted chains, were precisely controlled by adjusting synthesis parameters. The surface-grafted CNFs displayed a microgel structure in water and presented strong positive charge and high viscosity. By flocculation experiments, it was determined that the most effective surface-grafted CNF flocculant was characterized by two key features: spaced grafted chains and higher positive charge content. While flocculation performance was discovered to be most strongly influenced by positive charge, it was observed that longer graft chains could compensate for lower charge levels. Following structural optimization of surface-grafted CNF, most commercial flocculants were outperformed by the surface-grafted CNFs. Effective treatment of actual construction wastewater was also demonstrated, by which broader industrial applications were suggested.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2025
·
IF 13.2
Yue Zhang,Weibiao Wang,Mei Wang,Lijuan Ma,Weiman Zhang,Shuxian Zhang,Gidion Wilson,Zhigang Yang,Yuping Sa,Fen Ma,Xinmin He,Tao Gao,Hui Yuan,Guoning Chen,Xueqin Ma
β-Lactamases (β-LS) are a significant threat to public health due to their role in conferring antibiotic resistance against nearly all clinically used β-lactam antibiotics. Consequently, the search for β-lactamase inhibitors (β-LSI), which can reversibly bind to and inactivate β-LS, has intensified. Here, a sensitive and rapid cellulose-based colorimetric sensor integrated with affinity identification model was designed for high-throughput screening of β-LSI. The innovative concept of a nitrocefin-based colorimetric paper sensor strategy was effective in rapidly detecting the inhibitory effects of herbals on β-LS. Then, potential β-LSI present in the screened herbals were captured, separated, and identified utilizing affinity identification model. The efficacy of the developed method was validated with both negative and positive drugs and was subsequently applied to the screening of β-LSI in 7 different herbal samples. Notably, Ziziphus jujuba Mill. var. spinosa (Bunge) Hu ex H. F. Chou exhibited significant β-LS inhibitory activity. Further affinity separation and LC-MS analyses identified 2 bioactive compounds, spinosin, and magnoflorine, as the agents responsible for this inhibitory effect, with IC 50 values of 143.53 μM and 294.66 μM, respectively. The inhibitory effects and mechanisms were validated through antibacterial activity testing, molecular docking, and dynamic simulation. Notably, spinosin combined with aztreonam showed greater antibacterial effectiveness than avibactam. This study not only establishes a platform for the effective preliminary screening of β-LSI as a potential antimicrobial resistance-reversing agent for future clinical applications, but also inspires the further development of other cellulose-based colorimetric sensors for the rapid and high-throughput discovery of various enzyme inhibitors in complex natural medicines.
✓ 已验证
产品关联
DOI
高影响因子
ChemistrySelect
·
2024
·Vol. 9
·期 40
·e202403878
·
IF 1.9
Haifeng Liao,Jianwei Guo
Graphical Three kinds of heteropoly acid-based ionic liquids with different Hammett acidity were prepared for the catalytic conversion of cellulose to levulinic acid, and the effects of different solvent systems on the catalytic reactions were investigated. The results showed that higher Hammett acidity was beneficial to increase the yield of levulinic acid, and GVL/H 2 O bi-phase solvent system was helpful to extract the product to the organic phase and promote the formation of levulinic acid. Levulinic acid is an important chemical intermediate, which has many applications in organic synthesis, industry, agriculture, and medicine. In this word, three kinds of heteropoly acid based ionic liquids ([IMPS]H 2 PW 12 O 40 、[PyPS] H 2 PW 12 O 40 [TEAPS] H 2 PW 12 O 40) were used to catalyze the one-pot conversion of cellulose to levulinic acid. [IMPS]H 2 PW 12 O 40 has the highest catalytic activity due to its strong Hammett acidity ( H 0 ). In addition, the effect of biphasic solvent systems on the conversion of cellulose to levulinic acid was also studied. The results showed that the GVL/H 2 O system could effectively promote the conversion of cellulose and increase the yield of levulinic acid. The yield of levulinic acid could reach 52.6% and the conversion rate of cellulose was 91.2% at 180 °C for 180 min under the GVL/H 2 O volume ratio of 1:1 with [IMPS]H 2 PW 12 O 40 as a catalyst at 1 Mpa N 2 and cellulose as raw material. And [IMPS]H 2 PW 12 O 40 can be recycled up to five times without significant performance loss. This study provides a promising method for efficiently converting cellulose and other biomass resources to levulinic acid extraction.
✓ 已验证
产品关联
DOI
高影响因子
Advanced Fiber Materials
·
2024
·
IF 17.2
Gao Chong,Liu Yingcun,Gu Zongxue,Li Juan,Sun Yue,Li Wei,Liu Keshuai,Xu Duo,Yu Bin,Xu Weilin
Wearable electronics based on natural biomaterials, such as bacterial cellulose (BC), have shown promise for a variety of healthcare and human-computer interaction applications. However, current BC-based pressure sensors have an inherent limitation, which is the two-dimensional rigid structures and limited compressibility of BC restrict the sensitivity and working range for pressure sensing. Here, we propose a strategy for fabricating BC/polypyrrole/spacer fabric (BPSF) pressure sensors with a hierarchical structure constructed by integrating conductive BC nanonetwork into a compressible fabric frame via the in situ biofermentation process. The hierarchical structure design includes a cross-scale network from the nanoscale BC sensor networks to the macroscopic three-dimensional compressible fabric sensor network, which significantly improves the working range (0–300 kPa) and sensitivity (40.62 kPa −1 ) of BPSF. Via this unique structural design, the sensor also achieves a high fatigue life (~5000 cycles), wearability, and reproducibility even after several washing and abrasion cycles. Furthermore, a flexible and wearable electronic textile featuring an n × n sensing matrix was developed by constructing BPSF arrays, allowing for the precise control of machines and weight distribution analysis. These empirical insights are valuable for the biofabrication and textile structure design of wearable devices toward the realization of highly intuitive human-machine interfaces. Graphical Abstract
✓ 已验证
产品关联
DOI
高影响因子
MOLECULES
·
2024
·Vol. 29
·期 10
·2246
·
IF 4.2
Shasha Liu,Mei Sun,Can Wu,Kaixuan Zhu,Ying Hu,Meng Shan,Meng Wang,Kai Wu,Jingyi Wu,Zongli Xie,Hai Tang
Dye/salt separation has gained increasing attention in recent years, prompting the quest to find cost-effective and environmentally friendly raw materials for synthesizing high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose-structured NF membrane was fabricated via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-sized and finer-sized TOCNFs on a microporous substrate, followed by crosslinking with trimesoyl chloride. The resulting TCM membrane possessed a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterial additives. TCM membranes exhibit high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with the Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirmed the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red and orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ACS Sustainable Chemistry & Engineering
·
2024
·
IF 7.1
Qian Han,Yantao Wang,Huili Wang,Tongxin Zhou,Zhaoping Song,Dehai Yu,Xiaona Liu,Wenxia Liu,Shaohua Ge
To address the inadequate mechanical strength of alginate-based mulch films, this study presents an innovative approach employing a dual network strategy. The dual network consists of the alginate network cross-linked by gradually released calcium ions from nanometer-sized calcium carbonate and the micronano multiscale fiber network formed by mechanical entanglement and hydrogen bonds between microfibrils. The multiscale fibers were fabricated through a mechanical process with no fiber loss under normal atmospheric pressure. Scanning electron microscopy, transmission electron microscopy, and X-ray diffraction were used to examine the microstructure and crystallinity of the multiscale fibers. The obtained dual-network mulch films showed good characteristics, with optimum mechanical strength, water vapor permeability, and biodegradability. Notably, the stress strength of the mulch film reinforced with the multiscale fibers was approximately ten times greater than the tensile strength of the control film, reaching 84.7 MPa when CFBC was 7.7%. The multiscale fibers present a novel approach for material preparation and reinforcement due to their high yield, low energy consumption, easy preparation process, and good compatibility with other polymers.
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2024
·
IF 7.7
Jia-hui Wu,Jia-hui Liao,Teng-gen Hu,Min-hua Zong,Peng Wen,Hong Wu
In this study, an active and intelligent nanofilm for monitoring and maintaining the freshness of pork was developed using ethyl cellulose/gelatin matrix through electrospinning, with the addition of natural purple sweet potato anthocyanin. The nanofilm exhibited discernible color variations in response to pH changes, and it demonstrated a higher sensitivity towards volatile ammonia compared with casting film. Notably, the experimental findings regarding the wettability and pH response performance indicated that the water contact angle between 70° and 85° was more favorable for the smart response of pH sensitivity. Furthermore, the film exhibited desirable antioxidant activities, water vapor barrier properties and also good antimicrobial activities with the incorporation of ε -polylysine, suggesting the potential as a food packaging film. Furthermore, the application preservation outcomes revealed that the pork packed with the nanofilm can prolong shelf life to 6 days, more importantly, a distinct color change aligned closely with the points indicating the deterioration of the pork was observed, changing from light pink (indicating freshness) to light brown (indicating secondary freshness) and then to brownish green (indicating spoilage). Hence, the application of this multifunctional film in intelligent packaging holds great potential for both real-time indication and efficient preservation of the freshness of animal-derived food items.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
BIOMASS & BIOENERGY
·
2025
·
IF 5.8
Liyi Zhang,Guangyong Zeng,Jianquan Luo,Yinhua Wan,Benkun Qi
While the mechanism for extracting lignin from biomass using deep eutectic solvent (DES) pretreatment has been widely investigated, few studies have specifically identified the grafting of hydrogen bond donors from DES onto the lignin surface during pretreatment and examined the effect of lignin modification on enzymatic cellulose hydrolysis. This study combines choline chloride (CC) with lactic acid (LA), oxalic acid (OA) and glycerol (Gly) to treat lignin. Structural characterization confirmed the incorporation of LA and OA via esterification, and Gly via etherification, onto lignin surface. Enzymatic hydrolysis results indicated that CC-OA-treated lignin strongly inhibited hydrolysis, with glucose yields ranging from ∼30 % to ∼46 %. In contrast, CC-LA- and CC-Gly-treated lignin exhibited weaker inhibition, with glucose yields varying from ∼50 % to ∼59 % for the former and ∼47 %–∼60 % for the latter, compared to untreated lignin with glucose yields of 51.25 % and 38.95% at two loadings. Notably, a CC-Gly-treated lignin, with lower loading, resulted in glucose yields ranging from 57.02 % to 60.22 %, showing no inhibition on cellulose hydrolysis compared to the control without lignin addition (57.87 %). Physicochemical analyses revealed variations in water contact angle, surface charge, and total phenolic hydroxyl content among DES-treated lignin samples, affecting cellulase-lignin interactions—specifically hydrophobic, electrostatic, and hydrogen bonding. This study clarifies the relationship between DES composition, lignin modification, and enzymatic cellulose hydrolysis efficiency, providing valuable insights into the effects of DES-induced lignin modifications on cellulose saccharification and addressing a significant gap in the literature.
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Nano Materials
·
2024
·
IF 5.3
Yuyan Zhou,Guiyun Huang,Zhe Zhang,Liling Qin,Hui Cai,Jiulong Sha
Because of the increasing popularity of self-powered devices that use environmental or mechanical energy harvesting, triboelectric nanogenerators (TENGs) can be used as power sources in wearable electronic devices. However, the preparation of stretchable and flexible TENGs with outstanding electrical output performance is a challenge that requires further investigation. In this study, multiwalled carbon nanotubes (MWCNTs)/cellulose nanofibrils (CNFs)/poly(vinyl alcohol) (PVA) hydrogel-based TENGs that are stretchable, antifreezing, and highly conductive were developed. Doping of multiwalled carbon nanotubes and cellulose nanofibrils promotes the cross-linking of the hydrogel and the formation of microchannels within it, which not only improves ion transport to enhance hydrogel conductivity but also increases the triboelectric output through streaming potential. As the hydrogel is compressed, 2% MWCNTs hydrogel-based TENGs would generate an open-circuit voltage of 160 V in contact-separation mode and an induced voltage of 6.1 V was obtained via the streaming potential mechanism. A wearable sensor for motion detection was also developed using TENGs with outstanding stretchability and flexible performance. Because of their high sensitivity and effective mechanical energy-harvesting capabilities, ionic hydrogels hold promise for the development of next-generation, advanced wearable electronic devices.
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2024
·
IF 7.7
Wenjing Yang,Shikai Zhang,Chenchen Li,Mei Li,Yijing Li,Peng Wu,Houshen Li,Shiyun Ai
Polysaccharide-based films have received increasing attention as promising candidates for petrochemical plastics. However, they are highly brittle, poorly hydrophobic and without antibacterial activity, while current films used to address these issues often struggle to manage the balance between these properties. To achieve a balance of several performance indices of the films, functionalized dialdehyde cellulose nanocrystals (DCNCs) were prepared to activate pectin-based films. Structural characterization including dynamic light scattering techniques (DLS), scanning electron microscope (SEM), atomic force microscope (AFM), attenuated total reflection Fourier-transform infrared (ATR-FTIR) spectrometer and x-ray diffraction (XRD) demonstrated that DCNCs were homogeneously dispersed in the pectin polysaccharide matrix and tightly cross-linked through hydrogen bonding interactions, which promoted the stable formation of high-performance composite films. Compared to pure pectin film, the composite film has better tensile strength (23.09 MPa), water contact angle (WCA, 91.23°), water vapor permeability (WVP, 1.02 × 10 −12 g/cm·s·Pa), and exhibit excellent UV-resistance, DPPH radical scavenging capacity (27.04 %) and antibacterial activity that significantly extended the shelf life of strawberries (5 d). Furthermore, DCNCs can be used to enhance the mechanical strength (4.15–23.46 MPa), WVP (1.55–5.21 × 10 −12 g/cm·s·Pa) and WCA (59.46°–61.03°) of various polysaccharide-based films, which validates their universality. This work effectively improves and balances the several properties of polysaccharide-based films, creating more opportunities for the wide application of polysaccharide-based films, such as food preservation packaging.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Nano Energy
·
2025
·
IF 17.1
Mingyu Liu,Ruidong Chu,Guodong Li,Zhaoping Song,Dehai Yu,Huili Wang,Hong Liu,Wenxia Liu
It is still a challenge to establish a continuous electronic conductive network for conventional conductive hydrogels served for high-sensitive and comfortably wearable sensors. In this study, a micropatterned hybrid sheet, approximately 1 mm thick, was developed by infiltrating a multifunctional hydrogel precursor within a micropatterned nano-carbon aerogel sheet composed of partially carbonized cellulose nanofibers before gelatinization. The aerogel sheet, designed with parallel rectangular grooves and ridges, has a slightly lower modulus than the hydrogel. The hydrogel, gelatinized within the aerogel sheet in a glycerol-water binary system, features a dual-crosslinked network of bacterial cellulose and a hydrophobically associated copolymer. This design allows the hydrogel to absorb most of the stress during stretching, while the nano-carbon aerogel sheet undergoes controlled crack propagation, leading to uneven deformation and localized stress concentration. This unique stress-handling mechanism imparts the hybrid sheet with a gauge factor (GF) of 12.3ε¹ . ²⁷ up to 1000 % strain, pressure sensitivity (S) of 31.33p −0.71 in the 0–500 kPa range, humidity sensing capacity and exceptional cycling stability over 1000 cycles under 200 % strain or 50 kPa pressure. The sensor enables precise real-time health monitoring, rehabilitation, disease diagnosis, and human-computer interaction, highlighting the potential of the micropatterned hybrid sheet to advance sensor technology.
✓ 已验证
产品关联
DOI
高影响因子