International Journal of Electrochemical Science
·
2023
·Vol. 13
·期 12
·12226-12237
·
IF 1.5
Yanrong Li,Yao Liu,Zhongbin Li,Jiaqiang Li,Chaozhong Guo,Jin Zhang,Jinbiao Wang
Graphdiyne (GDY) as a novel allotrope has been theoretically predicted to be the most stable non-natural carbon allotropes. However, GDY has not been systematically investigated as a new carbon support to ORR catalysts. Thus, here we report a new strategy for the synthesis of Pd nanoparticles anchored on nitrogen-doped graphdiyne (CN x -Pd@GDY) electrocatalyst for oxygen reduction reaction (ORR) via a facile pyrolysis method. The results show that the prepared CN x -Pd@GDY catalyst has exhibited excellent ORR catalysis performance with a four-electron transfer pathway in 0.1 mol l -1 KOH electrolyte compared to other commercial carbon supports such as carbon black and carbon nanotubes. Electrochemical research results show that the as-formed CN x -Pd@GDY exhibits excellent electrocatalytic ORR activity with an onset potential of 0.96 V vs. RHE and a high long-term stability in the alkaline condition. The interaction between Pd nanocrystals and the encapsulating PANI shells was found in the catalyst, which markedly contributes to the improvement in ORR catalytic activity and stability of the catalyst. Such catalytic characteristics have reasonably indicated a great potential as a novel catalyst for ORR instead of the commercial Pt-based catalyst.
✓ 已验证
DOI
高影响因子
Scientific Reports
·
2015
·Vol. 5
·期 1
·12005
·
IF 5.578
Cui Yan-Li,Guo Xiao-Ning,Wang Ying-Yong,Guo Xiang-Yun
N-aryl imidazoles play an important role as structural and functional units in many natural products and biologically active compounds. Herein, we report a photocatalytic route for the C-N cross-coupling reactions over a Cu/graphene catalyst, which can effectively catalyze N-arylation of imidazole and phenylboronic acid and achieve a turnover frequency of 25.4 h −1 at 25 o C and the irradiation of visible light. The enhanced catalytic activity of the Cu/graphene under the light irradiation results from the localized surface plasmon resonance of copper nanoparticles. The Cu/graphene photocatalyst has a general applicability for photocatalytic C-N, C-O and C-S cross-coupling of arylboronic acids with imidazoles, phenols and thiophenols. This study provides a green photocatalytic route for the production of N-aryl imidazoles.
✓ 已验证
DOI
高影响因子
Petroleum Science
·
2021
·Vol. 18
·期 2
·654-666
·
IF 4.09
Wen Cheng-Long,Xu Jun-Dong,Wang Xue-Man,Fan Yu
To enhance the gasoline octane number, low-octane linear n-alkanes should be converted into their high-octane di-branched isomers via n-alkane hydroisomerization. Therefore, hierarchical SAPO-11-based catalysts are prepared by adding different contents of sodium dodecylbenzene sulfonate (SDBS), and they are applied in n -nonane hydroisomerization. When n (SDBS)/ n (SiO 2 ) is less than or equal to 0.125, the synthesized hierarchical molecular sieves are all pure SAPO-11, and as the SDBS content increases, the submicron particle size decreases, and the external surface area (ESA) increases. Additionally, these hierarchical SAPO-11 have smaller submicron particles and higher ESA values than conventional SAPO-11. When n (SDBS)/ n (SiO 2 ) is greater than 0.125, with increasing SDBS content ( n (SDBS)/ n (SiO 2 ) = 0.25), the synthesized SAPO-11 contains amorphous materials, which leads to a decline in the ESA; with the further increase in SDBS content ( n (SDBS)/ n (SiO 2 ) = 0.5), the products are all amorphous materials. These results indicate that in the case of n (SDBS)/ n (SiO 2 ) = 0.125, the synthesized SAPO-11 molecular sieve (S–S 3 ) has the most external Brønsted acid centers and the highest ESA of these SAPO-11, and these advantages favor generation of the di-branched isomers in hydrocarbon hydroisomerization. Among these Pt/SAPO-11 catalysts, Pt/S–S 3 displays the highest selectivity to entire isomers (83.4%), the highest selectivity to di-branched isomers (28.1%) and the minimum hydrocracking selectivity (15.7%) in n -nonane hydroisomerization.
✓ 已验证
DOI
高影响因子
CHEMICAL RESEARCH IN CHINESE UNIVERSITIES
·
2019
·Vol. 35
·期 2
·299-303
·
IF 1.071
Zang Dongyun,Zhao Guanjia,Liu Xiaona,Yin Jianguo,Ma Suxia
Densities of methyl nonanoate, n -dodecane, and their binary mixtures were investigated to provide the necessary data for their engineering applications as promising fuels and fuel additives. In the present work, densities were measured under atmospheric pressure at 293.15―463.15 K. The density data for the binary mixtures were fitted into a form of excess molar volume. The excess molar volumes were mostly positive, and the maximum value was obtained at molar fractions of n -dodecane between 0.5 and 0.6. Molecular simulations of specified systems were carried out by using four kinds of force fields, and the suitable force fields for describing the volume properties of the system were AMBER96 and OPLS-AA. The relative deviations for these two force fields between the simulated and the experimental data were well within ±4%, which meets the general engineering requirement.
✓ 已验证
DOI
高影响因子
EUROPEAN POLYMER JOURNAL
·
2015
·
IF 3.005
Hongwei Zhang,Qijian Niu,Ning Wang,Jun Nie,Guiping Ma
In this research a thermo-sensitive drug loaded core–shell fibers were prepared by UV photo-polymerization combined with electrospinning technology. The biodegradable polymer polylactic acid (PLA) was used as the core with electrospinning and the N-isopropylacrylamide (NIPAM) was selected to be shell of the fibers via UV photo-polymerization, respectively. Combretastatin A4 (CA4) was used as the model drug loaded in PLA (core structure) to test the thermo-sensitivity of the core–shell fibers. SEM was performed to observe the morphology of the fibers. TEM was carried out to confirm the core–shell structure of the fibers. Furthermore, XPS and FTIR results demonstrated that the core–shell structure had been fabricated as designed. Water contact angle (WCA) test indicated that the fibers show different wettability when the temperature was below or above the lower critical solution temperature (LCST). Moreover, in vitro drug release test was conducted to explore the difference of the drug release when the temperature was at 25 °C and 40 °C. The cell culture studies showed that the prepared core–shell structure nanofibers have a potential application in the biomedical fields as tissue engineering.
研究领域:
生物材料
·
药物递送
·
组织工程
·
高分子科学
·
纳米医学
✓ 已验证
DOI
高影响因子
BIOMACROMOLECULES
·
2025
·
IF 5.4
Yanyao Wang,Chengcheng Zhao,Taohong He,Weipeng Zhao,Annela M. Seddon,Dave J. Adams,Honghui Yang
Abundant reversible noncovalent interactions contribute greatly to the anisotropy of supramolecular morphologies and the transformation across multiple structures. However, the trigger (group) to drive the transformation remains obscure. Herein, H-bonding between free N-terminal amines of l-tryptophan derivatives (GTCn) and DMSO, triggering a morphological transition is revealed from flat to twisted nanoribbons by tuning DMSO/H2O ratios. Corresponding dynamic macroscopic morphology evolution from an aggregated cluster to a flower-like sphere of gel is observed under an optical microscope. Combined experiments and molecular dynamics (MD) simulations establish this H-bonding as the submolecular trigger, which simultaneously induces the change of π–π stacking, from the J-type to H-type. Alkyl chains at the C-terminus modulate structural dimensions, while gel thixotropy is governed by chiral morphology. These results provide a molecular strategy for precisely triggering twisted ribbon formation in self-assembly alongside the injectable chiral gel systems visible under optical microscopy.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ACS Applied Polymer Materials
·
2025
·
IF 4.7
Jingjing Gao,Yadong Wang,Jiaoyang Huang,Zongmin Zhu
In this work, an innovative MXene-based nanohybrid, denoted as MXene-PDS, is fabricated through the integration of MXene with P/N/S-functionalized organic oligomer via hydrogen bonding. The incorporation of low loadings of MXene-PDS imparts effective flame retardancy to polylactic acid (PLA) while maintaining its processing and mechanical properties. Under a loading of 3% MXene-PDS, PLA/3MXene-PDS attains the UL-94 V-0 rating and exhibits a limiting oxygen index (LOI) of 22.8%. The peak heat release rate (PHRR) is reduced by 12.5%. Additionally, mechanical properties present good enhancement, with a notable 36% improvement in impact performance. The significant reduction in viscosity of PLA/3MXene-PDS greatly improves the processing performance. This study proposes a method for preparing MXene-based nanomaterial with high flame retardancy, which can endow polymers with multiple performance characteristics by adding a single functional additive.
✓ 已验证
产品关联
DOI
高影响因子
ACS Chemical Neuroscience
·
2025
·
IF 3.9
Lingbo Zhao,Chunyan Hou,Yu Gao,Hong Jin,Chun-Feng Liu,Shuwei Li,Junfeng Ma,Shuang Yang
Parkinson’s disease (PD) is a progressive neurodegenerative disorder lacking definitive diagnostic tests. To identify new diagnostic biomarkers, we employed glycoproteomics-mass spectrometry (MS) to investigate dynamic changes in protein N-glycosylation across the serum, urine, and saliva of PD patients. Our comparative analysis of differentially expressed glycoproteins (DEGs) between PD patients and healthy controls (HCs) revealed distinct patterns. Specifically, ATPase phospholipid transporter 11B (ATP11B) was significantly upregulated in the serum of PD patients, while urine and saliva showed an opposite trend. Other key findings included elevated myeloperoxidase (MPO) in urine and clusterin (CLU) in serum. Zinc-α-2-glycoprotein (AZGP1), detected in all three biofluids, displayed increased sialylation and core fucosylation in serum but decreased levels in the saliva and urine of PD patients, along with a distinct bifucosylation pattern in saliva. These glycoprotein expression changes were further validated using enzyme-linked immunoassay (ELISA). Pathway analysis indicated that these DEGs are primarily involved in inflammatory response, complement activation, and synaptic plasticity, suggesting that glycosylation dysregulation may contribute to PD progression by modulating neuroinflammation and protein homeostasis. This study represents the first comprehensive analysis of multibiofluid N-glycosylation in PD. The findings offer potential biomarkers and provide insights into the molecular mechanisms of the disease, which could ultimately inform early diagnosis and the development of targeted therapies.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Analytical Methods
·
2025
·
IF 2.6
Tiechun Li,Mengjia Guo,Weiwei Luo,Quanping Diao,Linlin Lv,Pinyi Ma
Nitrite (NO2−) has been extensively utilized in the food industry as a preservative and colorant; however, excessive intake can lead to serious health issues, highlighting the need for accurate and efficient detection methods. In this work, blue fluorescent iron and nitrogen co-doped carbon dots (Fe/N-CDs) were synthesized via a one-step hydrothermal method using ferric chloride, ethylenediaminetetraacetic acid (EDTA), and diethylenetriamine (DETA) as precursors. The prepared Fe/N-CDs exhibited excellent peroxidase-like activity. By leveraging the catalytic activity of Fe/N-CDs and the oxidation and diazotization reactions induced by NO2−, we developed a dual-mode fluorescent and ratiometric colorimetric sensor for nitrite detection. The fluorescence and colorimetric methods had linear detection ranges of 2.5–75 μM and 2.5–100 μM, with detection limits of 0.68 μM and 1.19 μM, respectively. The developed dual-mode sensing platform was successfully applied to detect NO2− in both pickled vegetable and cured pork samples, demonstrating its feasibility in practical applications. Furthermore, the color of the reaction changed from blue to yellow as the NO2− concentration increased. Quantitative nitrite analysis was further achieved by capturing RGB values with smartphone-assisted color-recognition software, using the green-to-red (G/R) ratio as the analytical signal.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
FUEL
·
2025
·
IF 7.5
Dan Zhang,Maowei Luo,Xianming Zhu,Faisal Irshad,Hamzah A.S.M. Yaseen,Chao Mu,Yong Wang,Shengping Wang,Xinbin Ma
CO 2 hydrogenation to formate is a crucial process for achieving carbon neutrality. A biomass-derived N and P co-doped carbon-supported Pd catalyst (Pd/CNP) was fabricated. N and P co-doping could enhance the catalytic performance by modulating Pd electron cloud density (the Pd 0 /(Pd 2+ +Pd 0 ) ratio), promoting Pd dispersion, and increasing the content of pyrrole-N, which promoted the dissociation of H 2 and the adsorption and activation of CO 2 . Due to the strong interaction between Pd and the heteroatoms of N and P, the Pd/CNP catalyst exhibited the highest catalytic activity (TON = 1655) in samples with different doping and pyrolysis temperatures. Kinetic analysis showed that Pd/CNP reduced the activation energy of CO 2 hydrogenation to formate compared with that of Pd/C. The kinetic equation of Pd/CNP is R’= k·M NEt3-CO2 0.65 ·P H2 1.21 (NEt 3 refers to triethylamine), and NEt 3 -CO 2 is a better choice of carbon source for hydrogenation than bicarbonate and CO 2 , which is obviously different from that of Pd/C catalyst.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Materials Chemistry A
·
2026
·
IF 9.2
Fangfang Yang,Xiangxing Lv,Zixuan Zhang,Longji Cui,Changsheng Cao,Yaqiang Li,Zailai Xie,Xuefei Zhang
Platinum (Pt)-based materials continue to serve as the benchmark electrocatalysts for the hydrogen evolution reaction (HER), yet their large-scale application is limited by the inherent scarcity and prohibitive cost of platinum. Herein, we develop a Pt-based single atom catalyst comprising Pt atoms anchored in N-doped carbon (NC) encapsulated onto molybdenum carbide (Mo2C) microspheres. Structural analyses reveal an ultra-low Pt loading of 0.156 wt%, characterized by Pt–N4 configurations. Kinetic measurements show that the optimized Pt-NC@Mo2C exhibits exceptional HER performance with an overpotential of 37 mV at 10 mA cm−2 and a Tafel slope of 40 mV dec−1 in acidic solution, outperforming the commercial Pt/C (20 wt%) and most reported Pt-based catalysts. Experimental and theoretical studies demonstrated that the NC layer bridges the Pt atom and Mo2C, which not only stabilizes atomic Pt active sites but also modulates their electronic structures through electron transfer from Pt to Mo2C. This unique composite nanostructure optimizes and facilitates the adsorption of H* intermediates on the Pt-NC@Mo2C, thereby enhancing its HER performance.
✓ 已验证
DOI
高影响因子
JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS
·
2026
·
IF 6.7
Can Cui,Longhao Zeng,Xia Liu,Huihui Li,Bo Jiang,Da Guo,Huanjiang Wang,Yadian Xie
To address cadmium pollution in water bodies, a novel N-doped red mud-biochar magnetic composite (N-RCB) was prepared through one-step co-pyrolysis of corn stover and red mud at 800 °C, using ammonium chloride as a pore-forming agent and urea as a nitrogen source. The obtained N-RCB was applied for the efficient removal of Cd 2+ from aqueous solutions. The equilibrium adsorption capacity of N-RCB for Cd 2+ was 5.0 times and 4.2 times that of the pristine biochar (CB) and non-N-doped magnetic red mud-biochar (RCB), respectively. The maximum theoretical adsorption capacity of N-RCB for Cd 2+ could reach 473.25 mg·g –1 . Adsorption kinetics and isotherm studies indicated that the adsorption process of Cd 2+ onto N-RCB followed the pseudo-second-order kinetic model and the Freundlich isotherm model, suggesting that the process is dominated by chemisorption and heterogeneous multilayer adsorption. The thermodynamic parameters demonstrated that the adsorption process was spontaneous, endothermic, and driven by an increase in entropy. The adsorption mechanisms of Cd 2+ by N-RCB included pore filling, cation-π interactions, surface complexation, and electrostatic attraction. Coexisting ion experiments further demonstrated that N‑RCB exhibited good anti‑interference ability toward common ions such as K + , Na + , Mg 2+ , NO₃⁻, and Cl⁻. In addition, after five consecutive adsorption–desorption cycles, the removal efficiency of Cd 2+ by N-RCB remained above 88 %. These results indicate that N-RCB is a promising green and efficient material for the removal of Cd 2+ from water bodies, demonstrating significant application potential.
✓ 已验证
产品关联
DOI
高影响因子