PHYSICAL CHEMISTRY CHEMICAL PHYSICS
·
2016
·Vol. 19
·期 4
·2961-2973
·
IF 4.449
Shiyou Xing,Pengmei Lv,Jiayan Wang,Junying Fu,Pei Fan,Lingmei Yang,Gaixiu Yang,Zhenhong Yuan,Yong Chen
For high caloricity and stability in bio-aviation fuels, a certain content of aromatic hydrocarbons (AHCs, 8–25 wt%) is crucial. Fatty acids, obtained from waste or inedible oils, are a renewable and economic feedstock for AHC production. Considerable amounts of AHCs, up to 64.61 wt%, were produced through the one-step hydroprocessing of fatty acids over Ni/HZSM-5 catalysts. Hydrogenation, hydrocracking, and aromatization constituted the principal AHC formation processes. At a lower temperature, fatty acids were first hydrosaturated and then hydrodeoxygenated at metal sites to form long-chain hydrocarbons. Alternatively, the unsaturated fatty acids could be directly deoxygenated at acid sites without first being saturated. The long-chain hydrocarbons were cracked into gases such as ethane, propane, and C6–C8 olefins over the catalysts' Brønsted acid sites; these underwent Diels–Alder reactions on the catalysts' Lewis acid sites to form AHCs. C6–C8 olefins were determined as critical intermediates for AHC formation. As the Ni content in the catalyst increased, the Brønsted-acid site density was reduced due to coverage by the metal nanoparticles. Good performance was achieved with a loading of 10 wt% Ni, where the Ni nanoparticles exhibited a polyhedral morphology which exposed more active sites for aromatization.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA
·
2016
·
IF 1.34
Shan-guang SONG,Shi-lei TAN,Xiao-xiao QI,Wei WANG,Li-li WANG
YSZ/(Ni, Al) composite coatings were deposited on Inconel600 superalloy with ball peening (BP) and without (non BP) treatment using the electrophoretic deposition (EPD) technique, followed by vacuum sintering method. The structures and phase evolution of the coatings were studied with X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS). The relation between microstructures and properties of the BPs-coated samples was discussed. The results show that the adhesion strength and gain mass of the BPs-coated samples with isothermal oxidation at 1100 °C for 100 h are 3.3 N and 0.00817 mg/cm 2 , respectively, while those of the non-BPs-coated sample are 2.6 N and 0.00559 mg/cm 2 , respectively. The EDS mapping analysis indicates that an obvious outward diffusion of Cr from the substrate to BPs coated samples occurs after isothermal oxidation. The BPs-coated sample shows the superior adhesion and oxidation resistance compared with non-BPs-coated samples.
✓ 已验证
产品关联
DOI
高影响因子
RSC Advances
·
2016
·Vol. 6
·期 88
·85367-85373
·
IF 3.289
Wenle Ma,Li Wang,Junying Xue,Hongtao Cui
Usually, monolayer-stated nanosheets of hydroxides have to be prepared by a multiple step layer-exfoliation processe, following “bottom-up” mechanism. The related preparative procedure is quite exhaustive and low yielding. In this work, α-Ni(OH)2 monolayer nanosheets were successfully synthesized in pure ethanol solution with a high yield using NaOH as a precipitant, based on a facile one-step “bottom-up” strategy. It was proposed that the water-deficient environment in ethanol solution could not provide adequate water molecules for the formation of hydrogen bond to link the layers, resulting in monolayer formation. Due to the large interface between the monolayer and electrolyte, the obtained monolayer nanosheets presented high electrochemical performance.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Renewable and Sustainable Energy
·
2017
·Vol. 9
·期 6
·
IF 1.135
Ma Tong,Liu Yang,Yu Haimiao
In this study, a novel Ni-based catalyst supported by iron slag (IS) was used to catalyze the pyrolysis volatile matter of pine sawdust, and the catalytic characters of the novel catalyst were compared with those of alumina Ni-based catalysts. In addition, the catalytic performances of the novel iron slag Ni-based catalyst on pyrolysis volatile matter of biomass components (lignin, cellulose, and hemicellulose) were experimentally investigated. Experimental results showed that the iron slag Ni-based catalyst could remove more than 90% of tar, which was close to the catalytic performance of common alumina nickel catalysts. The temperature-programmed oxidation analysis results showed that the coke amount was less than 0.6% of IS Ni-based catalyst, indicating the superior performance to alumina nickel catalyst. The analysis results of the catalytic effect on biomass components volatile matter showed that the IS Ni-based catalyst could significantly improve the tar conversion of lignin (92.71%). We compared the dew points of various biomass components and found that lignin was the main influencing factor of the dew point of pyrolysis tar. The catalytic performance of the IS Ni-based catalyst verified the economic value and environmental effect of IS for its reutilization. We analyzed the catalytic effect of pyrolysis volatile matter of biomass components on the novel catalyst for the purpose of selecting proper biomass materials.
✓ 已验证
产品关联
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2017
·
IF 4.798
Chun Tang,Zhi Liang Zhao,Jie Chen,Bo Li,Liang Chen,Chang Ming Li
The direct urea fuel cell holds great promise for energy-sustainable developments and mitigating water contamination but it still faces a great challenge to overcome the sluggish kinetics of the urea oxidation reaction (UOR). In this work, we report Se-Ni(OH) 2 -shelled vertically oriented NiSe nanowires on a Ni foam as an electrocatalyst toward UOR, showing a low potential of 0.366 V vs. SCE to drive 100 mA cm −2 in alkaline solution and out-performing all the reported non-noble-metal UOR catalysts up to date. Experimental results and theoretical calculation reveal that the vertically and distantly arranged nanowires with highly porous structure produce high mass transport paths for urea to fully access the reaction sites, the NiSe core offers high conductivity for fast electron transport , and the Se-Ni(OH) 2 shell provides large amount of active catalytic sites while lowering the CO 2 adsorption/desorption barrier than Ni(OH) 2 for fast reaction kinetics. This work opens up an exciting new direction to design electrocatalysts for high performance fuel cells and other energy applications.
✓ 已验证
产品关联
DOI
高影响因子
MICROCHIMICA ACTA
·
2016
·Vol. 184
·期 1
·261-269
·
IF 4.831
Rao Hanbing,Lu Zhiwei,Ge Hongwei,Liu Xin,Chen Bingyao,Zou Ping,Wang Xianxiang,He Hua,Zeng Xianyin,Wang Yanying
The article describes an electrochemical creatinine sensor that is based on a glassy carbon electrode (GCE) modified with a magnetic molecularly imprinted polymer (MMIP) and a composite consisting of nickel nanoparticles and polyaniline that was prepared by electropolymerization. Aniline and methacrylic acid were used as the bifunctional monomers, and creatinine was used as the template molecule. Electrochemical deposition was performed via cyclic voltammetry in the potential range from −0.3 V to 1.2 V and at a scan rate of 50 mV·s -1 over 20 cycles. The Ni@PANI NPs were characterized by scanning electron microscopy, FTIR, X-ray diffraction and thermogravimetric analysis. The Ni@PANI-modified GCE was characterized by cyclic voltammetry, electrochemical impedance spectroscopy and differential pulse voltammetry. Under optimized conditions, the sensor displays a linear response to creatinine in the 40 to 800 nM concentration range, with a 0.2 nM detection limit. The method was successfully applied to the detection of creatinine in urine mimic and in spiked urine samples.
Schematic of the preparation and function of an electrochemical sensor for creatinine. A glassy carbon electrode (GCE) was modified with a magnetic molecularly imprinted polymer (MMIP), nickel nanoparticles and polyaniline. The MMIP can specifically recognize creatinine to which it responds in the 40 to 800 nM concentration range.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MOLECULAR CATALYSIS A-CHEMICAL
·
2016
·
IF 3.958
Xueliang Cui,Wei Zuo,Meng Tian,Zhengping Dong,Jiantai Ma
Ni MOF-derived N-doped magnetic mesoporous carbon-supported Pd nanoparticles (Pd/Ni-mCN) were prepared and used in the hydrodechlorination (HDC) of chlorophenols (CPs) water pollutants with H 2 at mild reaction conditions. The Pd/Ni-mCN catalyst was characterized in detail by transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), N 2 adsorption/desorption, and vibrating sample magnetometry (VSM). The Pd/Ni-mCN nanocatalyst showed high activity and complete HDC conversion of a target pollutant such as 4-CP after 90 min at ambient conditions. Other CPs compounds such as 2-CP, 3-CP, 2,4-dichlorophenol (2,4-DCP), and 2,4,6-trichlorophenol (2,4,6-TCP) were also tested in the HDC reaction. 2-CP was the only intermediate product in the HDC of 2,4-DCP, with phenol being the final product. The HDC of 2,4,6-TCP proceeded with the intermediate formation of 2-CP and 2,4-DCP, this being potentially originated from the steric hindrance of the ortho-substituted Cl atom. Additionally, Pd/Ni-mCN exhibited high catalytic stability and recyclability. Thus, Pd/Ni-mCN was successfully recycled owing to its superparamagnetic properties and reused for at least five times showing stable conversions (above 99% at 90 min) the HDC of 4-CP.
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2017
·
IF 6.216
Xiancai Jiang,Hongmei Li,Shuolin Li,Shaowei Huang,Changli Zhu,Linxi Hou
Spherical-structured nano-/micromaterials with tunable shell architectures and compositions are becoming increasingly important and attractive for electrochemical energy conversion and storage. Herein, we report the synthesis of novel Ni–Co alloy@carbon microspheres by calcining Co/Ni bimetallic metal-organic frameworks (MOFs) prepared by a facile solvothermal reaction. Their structures, dimensions and electrochemical performance can be optimized by simply tuning the Co/Ni molar ratio. Benefiting from the advantageous structural and compositional features, the obtained Ni–Co alloy@carbon microspheres display exceptional electrochemical performance when used as counter electrode (CE) catalysts for dye-sensitized solar cells (DSSCs). In particular, the optimized NiCo 0.2 @C CE delivers an impressive power conversion efficiency (PCE) of 9.30%, showing a ∼15.7% enhancement compared to that of Pt CE (8.04%). Additionally, the NiCo 0.2 @C CE also demonstrates a good long-term electrochemical stability for the I 3 − /I − electrolyte. This work may provide new options for the design and preparation of efficient electrocatalysts with novel morphologies and desirable compositions.
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2016
·
IF 7.145
Yong Yang,Mei Wang,Peili Zhang,Weihan Wang,Hongxian Han,Licheng Sun
Modification of p-type Si surface by active and stable earth-abundant electrocatalysts is an effective strategy to improve the sluggish kinetics for the hydrogen evolution reaction (HER) at p-Si/electrolyte interface and to develop highly efficient and low-cost photocathodes for hydrogen production from water. To this end, Si nanowire (Si-NW) array has been loaded with highly efficient electrocatalysts, M-B (M = Ni, Co), by facile and quick electroless plating to build M-B catalyst-modified Si nanowire-array-textured photocathodes for water reduction to H2. Compared with the bare Si-NW array, composite Si-NWs/M-B arrays display evidently enhanced photoelectrochemical (PEC) performance. The onset potential (Vphon) of cathodic photocurrent is positively shifted by 530–540 mV to 0.44–0.45 V vs RHE, and the short-circuit current density (Jsc) is up to 19.5 mA cm–2 in neutral buffer solution under simulated 1 sun illumination. Impressively, the half-cell photopower conversion efficiencies (ηhc) of the optimized Si-NWs/Co–B (2.53%) and Si-NWs/Ni–B (2.45%) are comparable to that of Si-NWs/Pt (2.46%). In terms of the large Jsc, Vphon, and ηhc values, as well as the high Faradaic efficiency, Si-NWs/M-B electrodes are among the top performing Si photocathodes which are modified with HER electrocatalysts but have no buried solid/solid junction.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Desalination and Water Treatment
·
2025
·
IF 1
Yuyao Zhang,Yajie Li,Salma Tabassum,Gelan Zenebewerk Getachew
In this study, CO 3 2− intercalated Ni-doped CoMn layered double hydroxides were synthesized by co-precipitation method and used as peroxonosulfate (PMS) activation to degrade phenol efficiently. The physical and chemical properties of the catalyst were characterized by a series of methods. The effects of catalyst dosage, PMS concentration and initial pH value on phenol removal rate were investigated. The degradation mechanism was investigated by electron paramagnetic resonance (EPR) and quenching experiments. Experimental results indicated that the phenol removal is significantly impacted by the sulfate radical (SO 4 •− ), superoxide anion (O 2 •− ) and singlet oxygen ( 1 O 2 ). Furthermore, the inclusion of Ni stimulates the REDOX cycle of Co and Mn, and the activation of PMS to form active free radicals is caused by the REDOX cycle of Co 2+ /Co 3+ , Mn 2+ /Mn 3+ /Mn 4+ , Ni 2+ /Ni 3+ .
✓ 已验证
产品关联
DOI
高影响因子
Journal of Energy Storage
·
2024
·
IF 8.9
Yuting He,Yongjin Zou,Cuili Xiang,Fen Xu,Yongpeng Xia,Yulian Chen,Shunxiang Wang,Zhicong Hu,Sijia Hao,Lixian Sun
Shape-stabilized composite phase change materials (CPCMs) with high photothermal conversion efficiency, high thermal storage capacity, and excellent thermal conductivity hold immense potential for diverse applications and market growth. This study employed a one-step substitution reaction followed by a thermal reduction technique to successfully affix Ni and Cu nanoparticles onto reduced graphene oxide (rGO) nanosheets , which were subsequently integrated into a nickel foam (NF) matrix. This process resulted in the fabrication of an NF/Ni-Cu@rGO porous carrier, facilitating the adsorption of polyethylene glycol (PEG) and the formation of CPCMs. Introducing Ni-Cu@rGO into the NF matrix enhanced the carrier framework, enabling improved PEG loading and leakage prevention. The hybridization of Ni-Cu@rGO effectively bolstered the interaction between the carrier framework and the phase change material (PCM), resulting in enhanced phase change performance. CPCMs prepared from the NF/Ni-Cu@rGO framework exhibited superior shape stability, higher thermal storage density, and enhanced recyclability than pure PCMs. Optimized CPCMs displayed melting and crystallization enthalpies of 121.13 J·g −1 and 113.44 J·g −1 , respectively. The thermal conductivity of NF/Ni-Cu@rGO/PEG CPCMs significantly improved to 0.4780 W·m −1 K −1 , representing a remarkable 315 % increase over that of PEG alone. Furthermore, the NF/Ni-Cu@rGO/PEG composite demonstrated outstanding photothermal conversion efficiency, thermal cycling stability, and exceptional shape stability. These findings offer promising prospects for its application across various fields.
✓ 已验证
产品关联
DOI
高影响因子
APPLIED CATALYSIS A-GENERAL
·
2024
·
IF 4.7
Meng Liu,Caixia Miao,Zhijie Wu
The direct synthesis of methyl acetate (MA) from methanol is an appealing and green approach, but an efficient catalyst is urgently needed. Herein, Cu-Ni bimetallic clusters, with a diameter of ∼1.2 nm, have been successfully encapsulated within BEA zeolite by an in-situ two-step encapsulation method (Cu-Ni@Beta), which significantly favors the dispersion of metals compared to the ion-exchanging (Cu/Ni@Beta) and wet impregnation approach (Cu-Ni/Beta). The as-synthesized Cu-Ni@Beta catalyst shows a MA formation rate of 1.46 mmol s −1 g (Cu+Ni) −1 , which is much higher than Cu/Ni@Beta of 0.02 mmol s −1 g (Cu+Ni) −1 and Cu-Ni/Beta of 0.12 mmol s −1 g (Cu+Ni) −1 . Characterization studies reveal that zeolite constraints could not only provide the spatial confinement for metal clusters but also induce an electronic interaction between confined Cu and Ni species in Cu-Ni@Beta. This interaction can increase and stabilize Cu + sites as well as Lewis acid sites, which are crucial for improving catalytic performance. In-situ FTIR experiments indicate that the formation of formaldehyde (CH 2 O*) is the critical step for methanol to MA, and the CH 2 O* further couples with methoxy (CH 3 O*) to form acetate species (CH 3 CHO*), which subsequently couples with CH 3 O* to produce MA.
✓ 已验证
产品关联
DOI
高影响因子