RSC Advances
·
2018
·Vol. 8
·期 15
·7924-7931
·
IF 2.936
Yanling Wang,Yongfei Li,Qian Wang,Qiang Li,Yue Zhang,Lin Yuan
The wettability of a rock’s surface is a vital factor for gas flow and fracturing fluid backflow. As a result of this, novel and effective gas wetting alteration agents are required. In this work, a gas-wetting alteration agent, N,N-bis(perfluorooctyl)imine acetate sodium, was synthesized and characterized by different methods. The wettability of a rock’s surface was evaluated by contact angle and imbibition measurements, the Owens two-liquid method and glass capillary tube rise testing. The results showed that after treatment with 0.5 wt% N,N-bis(perfluorooctyl)imine acetate sodium the contact angles of water and n-hexadecane on the surface of the rock increased from 36° and 0° to 140° and 119°, respectively. The surface free energy rapidly reduced from primeval 72 mN m−1 to 3.4 mN m−1 after treatment with 0.3 wt% N,N-bis(perfluorooctyl)imine acetate sodium. These values agreed with the imbibition measurements and the results of the glass capillary tube rise testing. Moreover, analysis by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) showed that the roughness of the rock surface significantly increased. The above results fully proved that the wettability of the rock surface is altered from its original water-wetting or oil-wetting to gas-wetting. Furthermore, thermal analysis demonstrated that the gas-wetting alteration agent has good thermal stability, which indicates its great potential to be used as a gas-wetting alteration agent for unconventional gas reservoirs under high temperature conditions.
研究领域:
石油工程
·
材料科学
✓ 已验证
DOI
高影响因子
Systems Microbiology and Biomanufacturing
·
2022
·Vol. 2
·期 3
·507-522
·
IF 0
Du Juanjuan,Zhang Liang
N -methyl- d -aspartic acid (NMDA), an amino acid existing in human and animal central nervous system, exerts agonist action on one of the glutamate receptor subtypes and is clinically used for treatment of diabetes, Parkinson’s and Alzheimer’s syndrome. In this study, an enzymatic protocol for the chiral resolution of N -methyl- d , l -aspartic acid was built with a predicted N -demethylase (GenBank ID: OJV90073.1) from the genome of Chloroflexi bacterium 54-19. Through sequence alignment, the enzyme shares an identity of 32.19% to 2UZZ (PDB ID) with a conserved catalytic center. Recombinantly expressed in Bacillus subtilis WB600 , the N -demethylase was characterized with optimal temperature and pH at 55 ℃ and 7.5, and adaptive temperature and pH were 40–60 ℃ and 6–8. The effects of organic solvents and metal ions were investigated as well. Compared with other previously reported sarcosine oxidases, the enzyme showed a specific N -demethylation activity against N -methyl- l -aspartic acid according to the analysis by chiral liquid chromatography, LC–MS/MS and a detection by polarimeter. The results demonstrated 76% of 4.5 mM N -methyl- d , l -aspartic acid could be chirally separated by 7 mg·L −1 enzyme after reaction of 80 min. This work provided a foundation for mild synthesis of NMDA in industry. Graphical abstract
研究领域:
生物化学
·
分子生物学
·
微生物学
·
药理学
✓ 已验证
DOI
CRYSTENGCOMM
·
2018
·Vol. 20
·期 8
·1151-1157
·
IF 3.304
Qiangwen Fan,Xiaowei Duan,Hong Yan
The solid state [2 + 2] photocycloaddition of N,N′-diacyl-1,4-dihydropyrazines has been investigated using thiourea as a template to preorient the reactants in the crystalline state in a manner that is beneficial for the [2 + 2] photocycloaddition. The structures of the photoadducts, syn-dimers and cage-dimers, were determined using NMR and single-crystal X-ray diffraction. According to the topochemical principles used to assess the feasibility of solid state photochemical [2 + 2] cycloaddition, topological analysis of cocrystals consisting of the N,N′-diacyl-1,4-dihydropyrazines and thiourea, as well as the syn-dimers, was performed to investigate the influence of packing modes and non-covalent interactions on their solid state photoreactivity. The results showed that the solid state [2 + 2] reactivities of both the N,N′-diacyl-1,4-dihydropyrazines assembled using thiourea and the syn-dimers were controlled by the topochemical orientation of the potentially reactive double bonds and the H-bonding interactions within the adjacent reactive molecules.
研究领域:
有机化学
·
光化学
·
晶体工程
·
超分子化学
·
药物合成
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2020
·Vol. 31
·期 15
·12638-12648
·
IF 2.22
Zhou Xiaohong,Chen Yongyang,Wang Peiying,Xu Chengyang,Yan Qishe
The AgI/BiPO 4 n–n heterojunction hybrids were favorably fabricated over amorphous particles AgI closely in contact with petty polyhedron-assembled star-like BiPO 4 by precipitation technology for the first time. The as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), UV–Vis diffuse reflectance spectra (DRS), electrochemical test, etc. The degradation of tetracycline hydrochloride (TC) and methylene blue (MB) was employed to testify the performance of as-prepared composites upon exposure of simulated solar light and the AB-X composites exhibited boosted degradation efficiency in comparison with the as-prepared pure BiPO 4 and AgI. For instance, the calculated k TC of pseudo-first-order kinetics model on 24 wt% AgI/BiPO 4 sample was 36 times relative to those on pure BiPO 4 . This enhanced activity might due to increased charge transfer and separation efficiency in the formed n–n heterojunction and the dominant reaction active species were authenticated by trapping experiments. Furthermore, the internal electric field in the AgI/BiPO 4 heterojunction and the transfer path of electron–holes were tentatively deduced through graphical elucidation.
研究领域:
材料科学
·
环境化学
·
光催化
·
纳米材料
·
半导体异质结
·
污染物降解
·
能源与环境技术
✓ 已验证
DOI
高影响因子
JOURNAL OF MOLECULAR STRUCTURE
·
2017
·
IF 1.753
Yun Bai,Po Yang,Tao Wang,Yi Gu
This work aims at probing the formation of hydrogen bonds in the blends of polybenzoxazines and additional hydrogen-bond donor moieties-containing compounds. Based on experimental study and computer simulations, we found that the dominant hydrogen bonds of p -cresol-aniline-based dimer ( p C-a-D) and polybenzoxazines (P p C-a) were OH⋯N while N,N ′-(pyridine-2,6-diyl)diacetamide (DAA) was NH⋯O C hydrogen bond. After blending p C-a-D or P p C-a with DAA, additional hydrogen bonds formed, i.e. , OH⋯O C and OH⋯ NH. Moreover, the total quantity of hydrogen bonds of the blends increased. These results suggested that hydrogen bonds formed between polybenzoxazines and the additional hydrogen-bond donor moieties-containing polymers or compounds, and furthermore would be desirable to foster the promoted performance. This novel insight about polybenzoxazine blends is anticipated to help researchers explore more blends of polybenzoxazines with excellent properties.
研究领域:
材料科学
·
化学
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2021
·
IF 13.273
Jingwei Zhu,Yu Liu,Benlin He,Wenyu Zhang,Lifang Cui,Sudong Wang,Haiyan Chen,Yanyan Duan,Qunwei Tang
The back interface issues including numerous defects and imperfect contact, mismatched energy level are regarded as the key detrimental factors causing serious charge recombination and energy loss ( E loss ) and inferior charge extraction to achieve high efficiency Hole transport materials-free (HTMs-free) carbon-based Perovskite solar cells (PSCs). To address this drawback, an effective interface engineering via depositing N, N'-Dicyclohexylcarbodiimide (DCC) at PVSK/Carbon back interface is creatively implemented to passivate CsPbBr 3 surface defects through forming interaction between N atoms with lone pair electrons and uncoordinated ions (eg Pb 2+ and Cs + ions) to suppress the defect states induced non-radiative recombination and E loss . Concurrently, the smoothness and valence band of PVSK film with DCC modification are increased to improve the contact and band alignment at back interface, respectively, remarkably accelerating hole extraction and transportation and also reducing E loss as well as charge recombination. As a result, the comprehensive performance of DCC interface modified HTMs-free carbon-based CsPbBr 3 PSCs is significantly enhanced, especially the champion efficiency boosts to 10.16% from 6.60% of the control PSC. Furthermore, owing to the enhanced hydrophobicity and decreased imperfections of PVSK film with DCC modification, the optimized device without any encapsulation displays an excellent long-term stability under 85% RH air condition at 85 °C over 1200 h.
研究领域:
材料科学
·
光伏技术
·
界面化学
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING RESEARCH & DESIGN
·
2018
·
IF 2.795
Mengjie Sun,Meng Li,Pin Wang,Xu Zhang,Cuiming Wu,Yonghui Wu
Anion exchange membranes are prepared by phase inversion of P84 co -polyimide to obtain porous structure, and then chemically modified by branched polyethylenimine. The porous membranes are compared with a dense P84 membrane. The dense membrane is hydrophobic with large area resistance (>85 Ω cm 2 ), while the porous membranes are hydrophilic with low area resistance (2.4–3.5 Ω cm 2 ), lower than that of commercial membrane CJMA-3 (6.0 Ω cm 2 ). The ion exchange capacities are in the range of 0.83–0.86 mmol/g and the water uptake values are 90–130%, both of which are higher than those of dense P84 membrane and CJMA-3 membrane (0.5–0.6 mmol/g; 15–20%). The P84 co -polyimide membranes are utilized in bipolar membrane electrodialysis (BMED) process to produce N -2-hydroxyethylpiperazine- N ′-2-ethanesulfonic acid (HEPES). The porous membranes can decrease the transport resistance of HEPES − ions and yield high recovery ratio and current efficiency, while the dense membrane is unsuitable for BMED . The output of HEPES is increased significantly if the membranes have finger- or tear-like pores, as well as higher ion exchange capacity. The HEPES − recovery ratios are 52.3–61.6% after running 6 h under 40 V, which are higher than that of membrane CJMA-3 (46.5%). The current efficiency can reach up to 86.1% and the energy consumption is only 3.92 kWh/kg by using the optimal porous membrane M-1, which are better than membrane CJMA-3 (65.5%, 5.15 kWh/kg). Hence, the porous membranes have high potential for producing organic acid with high molecular weight.
研究领域:
化学工程
·
材料科学
✓ 已验证
DOI
高影响因子
MICROPOROUS AND MESOPOROUS MATERIALS
·
2019
·
IF 4.182
Xu Zhang,Yaquan Wang,Xiao Wang,Hengbao Chen,Hongyao Li,Chao Sun,Liying Sun,Chunyang Fan,Cui Wang
In this study, an efficient route was developed to prepare high quality erionite (ERI) zeolite by hydrothermal conversion of faujasite (FAU) zeolite as an aluminosilicate source in the presence of N,N -dimethylpiperidinium hydroxide (DMPOH). Pure ERI zeolite was successfully synthesized within only 8 h by carefully controlling the alkalinity (OH − /SiO 2 ) of the initial gel and the proportion of DMP + and K + . Compared with the conventional ERI zeolite synthesized via a Charge Density Mismatch method, the FAU-derived ERI zeolites show superior properties such as higher crystallinity , smaller crystal size, larger micropore volume and better hydrothermal stability. In addition, catalytic test in the ethanol dehydration reaction shows that the ERI zeolites obtained from FAU exhibit extraordinary performances to those of the conventional one. Finally, crystallization process from FAU to ERI was investigated in detail by UV Raman and XRD . The results show that the framework of ERI zeolite is formed by rearrangement of 4-rings generated from the initial FAU zeolite.
研究领域:
材料科学
·
催化化学
✓ 已验证
DOI
高影响因子
Nano Research
·
2022
·Vol. 16
·期 6
·8269-8280
·
IF 10.269
Wu Hao,Song Ziyu,Wang Xingxing,Feng Wenfang,Zhou Zhibin,Zhang Heng
Effective passivation of aluminum (Al) current collector at high potentials (> 4.0 V vs. Li/Li + ) is of essence for the long-term operation of lithium-based batteries. Unfortunately, the non-aqueous liquid electrolytes comprising lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) and organic carbonates are corrosive toward Al current collector at high potentials (> 4.0 V vs. Li/Li + ), despite their intriguing features (e.g., good chemical stability and high ionic conductivity). Herein, we propose the utilization of N,N-dimethyl fluorosulfonamide (DMFSA) as electrolyte solvent for suppressing Al corrosion in the LiTFSI-based electrolytes. It has been demonstrated that the electrolyte of 1.0 M LiTFSI-DMFSA shows decent ionic conductivities (1.76 mS·cm −1 at 25 °C) with good fluidities (2.44 cP at 25 °C). In particular, the replacement of organic carbonates (e.g., ethylene carbonate and ethyl methyl carbonate) with DMFSA leads to significant suppressed Al corrosion. Morphological and compositional characterizations utilizing scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) reveal that DMFSA favors the formation of insoluble species (i.e., aluminum fluoride (AlF 3 )) on the surface of Al electrode, which effectively inhibits continuous exposure of fresh Al surface to electrolyte during cycling. This work provides not only a deeper understanding on the Al corrosion in LiTFSI-based electrolyte but also an elegant path to stabilize the Al current collector at high potentials (> 4.0 V vs. Li/Li + ), which may give an impetus into the development of lithium-based batteries.
研究领域:
电化学
·
材料科学
·
储能技术
·
腐蚀科学
·
电池技术
✓ 已验证
DOI
高影响因子
PREPARATIVE BIOCHEMISTRY & BIOTECHNOLOGY
·
2017
·
IF 1.361
Xiaoyan Li,Chen Qi,Peilian Wei,Lei Huang,Jin Cai,Zhinan Xu
Uridine 5′-diphosphate N-acetylglucosamine (UDP-GlcNAc) is a natural UDP-monosaccharide donor for bacterial glycosyltransferases, while uridine 5′-diphosphate N-trifluoacetyl glucosamine (UDP-GlcNTFA) is its synthetic mimic. The chemoenzymatic synthesis of UDP-GlcNAc and UDP-GlcNTFA was attempted by three recombinant enzymes. Recombinant N-acetylhexosamine 1-kinase was used to produce GlcNAc/GlcNTFA-1-phosphate from GlcNAc/GlcNTFA. N-acetylglucosamine-1-phosphate uridyltransferase from Escherichia coli K12 MG1655 was used to produce UDP-GlcNAc/GlcNTFA from GlcNAc/GlcNTFA-1-phosphate. Inorganic pyrophosphatase from E. coli K12 MG1655 was used to hydrolyze pyrophosphate to accelerate the reaction. The above enzymes were expressed in E. coli BL21 (DE3) and purified, respectively, and finally mixed in one-pot bioreactor. The effects of reaction conditions on the production of UDP-GlcNAc and UDP-GlcNTFA were characterized. To avoid the substrate inhibition effect on the production of UDP-GlcNAc and UDP-GlcNTFA, the reaction was performed with fed batch of substrate. Under the optimized conditions, high production of UDP-GlcNAc (59.51 g/L) and UDP-GlcNTFA (46.54 g/L) were achieved in this three-enzyme one-pot system. The present work is promising to develop an efficient scalable process for the supply of UDP-monosaccharide donors for oligosaccharide synthesis.
研究领域:
生物化学
·
酶学
·
合成生物学
·
微生物学
✓ 已验证
DOI
PubMed
高影响因子
CRYSTENGCOMM
·
2013
·Vol. 15
·期 36
·7274-7284
·
IF 3.879
Xiu-Li Wang,Fang-Fang Sui,Hong-Yan Lin,Chuang Xu,Guo-Cheng Liu,Ju-Wen Zhang,Ai-Xiang Tian
Six new transition metal coordination polymers, namely, [Co(1,2-BDC)(L)1.5(H2O)] (1), [Co(1,3-BDC)(L)(H2O)2]·H2O (2) [Co(5-AIP)(L)0.5(H2O)]·2H2O (3), [Cu(1,2-BDC)(L)] (4), [Cu(1,3-BDC)(L)(H2O)]·3H2O (5), and [Cu2(5-AIP)2(L)2(H2O)]·6H2O (6) (L = N,N′-di(3-pyridyl)octanediamide, 1,2-H2BDC = 1,2-benzenedicarboxylic acid, 1,3-H2BDC = 1,3-benzenedicarboxylic acid, 5-H2AIP = 5-aminoisophthalic acid), have been hydrothermally synthesized and structurally characterized by single crystal X-ray diffraction. In compound 1, the adjacent CoII ions are connected by L ligands to form a 1D chain with an alternating arrangement of L ligands and Co2L2 dinuclear loops. The 1,2-BDC anions coordinate with one CoII ion in a bis(monodentate) chelate mode. Complex 2 shows a 2D (44) grid network with the sql topology, which consists of the 1D zigzag [Co–L]n chain and 1D linear [Co-1,3-BDC]n chain. When 5-H2AIP is used in compound 3, an interesting 2D terraced-type layer based on 1D [Co-5-AIP]2n ladder-like chains and μ2-bridging L ligands with 3,4-connected {62.10}{6} topology is formed. Under the similar conditions to compound 1, except that the cobalt(II) salt is replaced by a copper(II) salt, a 2D wave-like network 4 with 2,4-connected {64.8.10}{6} topology is obtained. Compound 5 displays a 3D coordination polymeric architecture based on 1D [Cu-1,3-BDC]n chains and [Cu–L]n chains, which represents an intriguing 3-fold interpenetrating framework with CdSO4-type topology. When 1,3-BDC is replaced by 5-AIP, another 3-fold interpenetrating 3D CdSO4-type coordination framework for compound 6 is obtained, which is constructed from three types of 1D chains: [La–Cu–Lc]n chain, [Lb–Cu–Lb]n chain and [Cu-5-AIP]n chain. The adjacent 1D chains for 1 and 2D layers for compounds 2, 3 and 4 are further extended by hydrogen bonding interactions to 3D supramolecular frameworks. The effect of dicarboxylates and central metals on the structures of the title complexes has been discussed. Furthermore, the electrochemical behaviors and solid state fluorescent properties for compounds 1–6 are investigated.
研究领域:
化学
·
材料科学
✓ 已验证
DOI
高影响因子
POLYMER SCIENCE SERIES A
·
2018
·Vol. 60
·期 5
·612-617
·
IF 0.729
Wang Jinjing,Wang Huifeng,Li Yan,Tian Li,Chen Shanmin,Liu Qiang,Guo Zhen
A novel copolymer surfactant has been prepared via a free radical copolymerization of CO 2 -switchable monomer N , N -diethylaminoethyl methacrylate and the hydrophilic monomer sodium vinyl-sulfonate and characterized. The results of conductivity, dynamic light scattering and cryogenic transmission electron microscopy study showed the change of the microstructure of copolymer in water by adding or removing of CO 2 . The copolymer aqueous solution was found to exhibit reversible switchability by the bubbling of CO 2 /N 2 .
研究领域:
高分子化学
·
材料科学
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）