Energy Technology
·
2020
·Vol. 8
·期 10
·2000606
·
IF 3.404
Yu Wang,Nachuan Yang,Yi Shuai,Kanghua Chen
Na 3 PS 4 -based materials, which have relatively high conductivities, make promising Na-ion solid electrolytes for realizing all-solid-state sodium batteries. Herein, Na 2.9375 PS 3.9375 Cl 0.0625 solid electrolytes’ power is prepared by a mechanical ball milling process and subsequent heat treatment process using low-cost Na, NaCl, P 2 S 5 , and S as raw materials. In addition, its electrical conductivity and electrochemical performance by compounding with polyethylene oxide–NaClO 4 are studied. The results show that Na 2.9375 PS 3.9375 Cl 0.0625 solid electrolyte heated at 550 °C with polyethylene oxide–NaClO 4 exhibits Na-ion conductivity of 8.75 × 10 −4 S cm −1 . The pragmatic and cost-effective raw materials grant the solid electrolyte with high-performance and higher practical value.
研究领域:
材料科学
·
电化学
·
能源存储
·
固体离子学
·
无机非金属材料
✓ 已验证
DOI
高影响因子
EUROPEAN POLYMER JOURNAL
·
2013
·Vol. 49
·期 6
·1731-1741
·
IF 2.562
Wenwen Yu,Dezhi Zhang,Miao Du,Qiang Zheng
A series of novel polyurethane (PU)/epoxy resin (EP) graft interpenetrating polymer network (IPN) composites with graded length side chains were prepared from toluene diisocyanate (TDI), polytetrahydrofuran glycol (PTMG), EP, trimethylolpropane (TMP), and diol chain extenders. The effects of the side chain lengths, content, and groups on the damping properties and mechanical properties were investigated. Two damping peaks were observed in the PU/EP IPN system, indicating that the peak damping factor (tan δ ) increased with increased side chain length at low temperatures. The introduction of an apolar side chain slightly narrowed the damping range. However, the side chain carrying polar groups broadened the damping temperature range. The strong H-bond interaction between the ester group of side chain and the N H of hard segments in PU was believed to favor microphase separation to form a larger-sized domain and induce the appearance of the relaxation peak at high temperatures. Consequently, the effective damping temperature range was broadened. The side chain content tethered in the hard segment remarkably influenced the damping properties of PU/EP IPNs both at low and high temperatures. The width and intensity of the tan δ peaks of PU/EP IPNs increased with increased side chain content. The mechanical properties (tensile strength and elongation at break) were significantly affected by the side chain content. Thus, an important method of improving the mechanical damping of elastomers by controlling the side chain molecular structure was established.
研究领域:
高分子材料科学
·
功能高分子
·
阻尼材料
·
复合材料
·
聚合物共混物
·
材料力学
✓ 已验证
DOI
高影响因子
MICROPOROUS AND MESOPOROUS MATERIALS
·
2024
·
IF 4.8
Guojun Lv,Xuyang Zou,Yan Chen,Qing Zhang,Xubin Zhang,Fumin Wang
The successful one-pot synthesis of MCM-41/MFI composite is mainly concentrated on the trivalent heteroatom of Al 3+ and Fe 3+ , however there are almost no reports about the one-pot synthesis of Ti-MCM-41/MFI composite. In this work, we reported the one-pot synthesis of Ti-MCM-41/MFI composite with a temperature-gradient hydrothermal strategy using hexadecyl trimethylammonium bromide CTAB and silicalite-1 seed as structure directing agents as well as ammonia solution as alkali source, and its application as heterogeneous catalyst in the cyclohexene epoxidation reactions. The impact of Si/Ti molar ratio and ammonia dosage as well as CTAB amount on the formation and property of Ti-MCM-41/MFI composite were systematically investigated. In addition, a possible partial transformation mechanism of Ti-MCM-41/MFI composite sample was proposed. The synthesized Ti-HMZ-50-N3.77-Se0.05 sample with ordered mesoporous structure and high content of framework titanium active centers revealed the eminent cyclohexene epoxidation performance, achieving a 32.51 % of cyclohexene conversion and a 61.27 % selectivity of cyclohexene oxide within 5 h of reaction.
研究领域:
催化化学
·
材料化学
·
纳米材料
·
多相催化
·
绿色化学
✓ 已验证
DOI
高影响因子
Sustainable Energy & Fuels
·
2021
·Vol. 5
·期 5
·1538-1547
·
IF 6.367
Ruyan Lei,Yanping Yang,Chenjuan Yu,Yinsi Xu,Yuanzhuo Li,Jun Li
In order to improve the electrochemical performance and efficiently prepare a solid polymer electrolyte (SPE) for the lithium-metal battery (LMB), a fumed SiO2 (FS) with surface Si–OH group was used to fabricate FS-modified poly(ethylene oxide) (PEO)–LiClO4-based SPE by a facile preparation process. The influences of the FS content on the morphological properties, thermal properties, lithium salt dissociation, mechanical properties, and electrochemical properties of SPE were systematically analyzed. Results indicate that FS with the hydrophilic property was widely distributed throughout the amorphous phase of SPE, thus the crystallinity of SPE was reduced to 25.83% when the FS mass loading was 6.85 wt%. In addition, a greater dissociation degree of lithium salt was achieved after the addition of FS, and a higher ion conductivity of 3.03 × 10−4 S cm−1 and Li-ion migration number of 0.396 were recorded at 60 °C. The all-solid-state Li/SPE/Li coin cell showed excellent stable cyclability (380 h) and the LiFePO4 (LFP)/SPE/Li coin cell demonstrated good discharge specific capacity and coulomb efficiency of 96 mA h g−1 and 100.2%, respectively, after 100 cycles of galvanostatic charge–discharge operation under 0.5C at 60 °C. Thus, based on collective results, it is expected that SPE presented in this work is a promising electrolyte for next-generation high-energy all-solid-state LMB with enhanced safety.
研究领域:
材料科学
·
电化学
·
能源存储
·
高分子化学
·
固态离子学
✓ 已验证
DOI
高影响因子
PROGRESS IN ORGANIC COATINGS
·
2018
·
IF 2.955
Yuhua Dong,Siyi Li,Qiong Zhou
The self–healing capability of epoxy coatings modified with coaxial core–shell nanofibers loaded with the corrosion inhibitor 2–mercaptobenzothiazole (MBT) was investigated using electrochemical techniques. The polyvinyl alcohol/polyvinylidene fluoride core–shell nanofibers were prepared by coaxial electrospinning. Electrochemical impedance results showed that the MBT–loaded coaxial nanofibers improved the barrier properties and decreased the corrosion activity of the coatings. Results of the Scanning Kelvin Probe technique revealed that the MBT–loaded coaxial nanofibers healed corrosion over artificial defects exposed to NaCl electrolytes. These results indicate that adding MBT–loaded coaxial nanofibers to epoxy coatings is a promising strategy toward the development of self–healing epoxy coatings.
研究领域:
材料科学
·
高分子化学
·
腐蚀与防护
·
表面工程
·
功能材料
✓ 已验证
DOI
高影响因子
PHYSICAL CHEMISTRY CHEMICAL PHYSICS
·
2017
·Vol. 19
·期 25
·16785-16794
·
IF 4.123
Wei Xia,Jun Zhao,Tao Wang,Li Song,Hao Gong,Hu Guo,Bing Gao,Xiaoli Fan,Jianping He
Polymer networks such as those of epoxy resin, as common protection materials, possess radiolytic oxidation degradation effects under gamma irradiation environment, which have a great accelerating effect on the ageing rate and severely limit their potential applications for metal protection in the nuclear industry. To overcome this, we report a simple scheme of anchoring crystalline ceria nanoparticles onto graphene sheets (CG) and incorporate it into the epoxy resin, followed by thermal polymerization to obtain CeO2/graphene-epoxy nanocomposite coating (CGNS). We had proven that graphene might act as “interwalls” in the epoxy matrix, which will result in space location-obstruct effect as well as absorb the radicals induced by γ-ray irradiation. Moreover, owing to the interconversion of cerium ions between their +3 and +4 states coupled with the formation of oxygen vacancy defects, electron spin resonance (ESR) detection shows that CeO2/graphene (CG) could act as a preferable radical scavenger and achieve better performance in trapping radicals than single graphene based composite. Electrochemical data strongly demonstrate that CeO2/graphene is capable of maintaining the anti-corrosion properties under gamma irradiation environment. Therefore, the designed hybrid CeO2/graphene-epoxy composite can be considered as potential candidates for protective coatings in nuclear industry.
研究领域:
材料科学
·
核工业防护
·
高分子化学
·
纳米复合材料
·
电化学防腐
✓ 已验证
DOI
高影响因子
CARBOHYDRATE POLYMERS
·
2018
·
IF 5.158
Dangge Gao,Jiahao Zhang,Bin Lyu,Leihong Lyu,Jianzhong Ma,Lintao Yang
The composite after referred to as P(DMDAAC-AGE)/(Ce-ZnO) was prepared via free radical polymerization by polymer including quaternary ammonium salt and epoxy group which grafted onto the surface of Ce-ZnO. ZnO nanorods, Ce-ZnO nanorods, P(DMDAAC-AGE), P(DMDAAC-AGE)/ZnO composites, P(DMDAAC-AGE)/(Ce-ZnO) composites and commercial antimicrobials were respectively treated on the cotton fabrics and their biological properties were investigated. There is a synergistic effect between Ce-ZnO and N + from the polymer in the fabric treated with P(DMDAAC-AGE)/(Ce-ZnO) composite so that it had a better antibacterial activity than pure polymer and pure Ce-ZnO. The antimicrobial rate of fabric treated with P(DMDAAC-AGE)/(Ce-ZnO) composite could reach up to 96%. And in order to investigate the durable ability, the fabric was washed multiple times to simulate the daily use washing. The result showed that the fabric still gave a superior antibacterial performance after 11 cycles (the equivalent of 55 times house laundering). Simultaneously, the differences in the amount of P(DMDAAC-AGE)/(Ce-ZnO) composite deposited on the fibers after washing were also investigated.
研究领域:
材料科学
·
高分子化学
·
纳米复合材料
·
纺织功能材料
·
抗菌材料
✓ 已验证
DOI
高影响因子
PROGRESS IN ORGANIC COATINGS
·
2020
·
IF 4.469
Haihua Wang,Wenjing Zhang,Yongning Ma,Guiqiang Fei,Huan Wen,Liyu Sun,Yanming Shao,Yong-Mook Kang
The compatibility between polypyrrole (PPy) and waterborne epoxy coating (EP) remains the main challenge. Here, phosphorylated poly (vinyl alcohol) (PPVA) and p-toluene sulfonic acid sodium (p-TSA) were simultaneously utilized as dopants to modify PPy and prepare water dispersible PPVA/p-TSA/PPy (PPVAT/PPy) solution. Additionally, poly (vinyl alcohol) (PVA) and TSA were also adopted to prepare PVA/p-TSA/PPy (PVAT/PPy) for comparison. Denser film with granular morphology was observed for PPVAT/PPy nanocomposite film. Compared with PVAT/PPy-40 %, the tensile strength of PPVAT-8.0 %/PPy-40 % increased from 248.8–283.9 MPa. PPVAT/PPy displayed higher compatibility and interactions with EP compared to PPy-TSA and PVAT/PPy. Compared with EP, the impedance modulus of PVAT/PPy+EP and PPVAT/PPy+EP increased from 3.17×10 5 to 1.07×10 8 and 1.62×10 9 Ω·cm 2 ; corrosion current density I corr decreased from 1.49×10 −6 to 7.72×10 -8 and 4.01×10 -9 A·cm -2 ; corrosion potential E corr displayed a positive shift of 230 mV and 269 mV, respectively. The corrosion inhibition efficiency of PPVAT/PPy+EP reached 99.83 %, which is much higher than that of PVAT/PPy+EP (93.97 %). PPVAT/PPy+EP nanocomposite coating has been proved to have preferable long-term corrosion resistance based on electrochemical impedance spectra (EIS), polarization curves and salt water spray test. The simultaneous incorporation of phosphate anions, sulfate ions and PPy into EP was beneficial to fabricate high-performance anticorrosion coating.
研究领域:
材料科学
·
高分子化学
·
腐蚀防护
·
纳米复合材料
·
表面工程
✓ 已验证
DOI
高影响因子
POLYMERS FOR ADVANCED TECHNOLOGIES
·
2015
·Vol. 26
·期 8
·953-959
·
IF 1.757
Shuting Wang,Lan Cen,Qihao Wu
Maleated glycidyl 3-pentadecenyl phenyl ether with styrene (MGS) was synthesized from glycidyl 3-pentadecenyl phenyl ether (GPPE), maleic anhydride (MAH) and styrene (St) in the presence of AIBN initiator at 80°C, and then the resultant MGS was applied as a compatibilizer to prepare SBR/silica composites. Meanwhile, the commercial compatibilizer bis-(triethoxysilylpropyl) tetrasulfide (named Si69) added into composite was also prepared for comparison purpose. The synthetic MGS structure was characterized by GPC and FTIR, and SBR/silica compounds with different compatibilizer were analyzed using RPA, DMA and so on. The results showed that M̄n and M̄w of MGS were 19,538 g/mol and 23,790 g/mol, respectively. The curing time of compounds with MGS increased, whereas the maximum and minimum torques decreased. The addition of MGS decreased Payne effect of SBR/silica compounds, which implied an improvement of silica dispersion in the compounds. Bound rubber content of compound with MGS was about 1.7 times higher than the absence and 1.5 times higher than that with Si69. The tensile strength of the composites was improved by increasing compatibilizer loading, and the optimum value was observed at 6 phr of MGS. Meanwhile the use of MGS can improve the anti-aging property of composite. According to DMA, the tanδ value at 0°C of composite with MGS was higher than composite without compatibilizer suggesting that MGS can improve the wet skid resistance of composite. The SEM analysis revealed that introduction of MGS enhanced the compatibility between SBR and silica. Copyright © 2015 John Wiley & Sons, Ltd.
研究领域:
高分子化学
·
橡胶复合材料
·
材料界面科学
·
功能高分子
·
聚合物改性
✓ 已验证
DOI
高影响因子
POLYMER TESTING
·
2020
·
IF 3.275
Rui Wang,Congzhen Xie,Bin Gou,Huasong Xu,Shoukang Luo,Jiangang Zhou,Leilei Zeng
Dielectric polymers with high thermal conductivity are very promising in the fields of aerospace and electronic device packaging. However, composites with excellent dielectric properties usually have low thermal conductivity. It is usually to fill the polymer with thermal conductivity particles to improve the thermal conductivity, but the high content of filler often reduces the mechanical properties of the polymer. In this paper, the traditional insulating polymer epoxy resin was used as the matrix, by covering the surface of silicon carbide with graphene to form a core-shell structure and co-filled with nano diamonds to achieve the preparation of high-performance epoxy resin at low content. The results showed that at the filling content of 30 wt%, the thermal conductivity of epoxy nanocomposites showed a dramatic thermal conductivity enhancement of 1263%, the energy storage modulus increased by 1.1 GPa, and the dielectric loss remained unchanged at 50 Hz. The advantages of the composite are the structural design and surface modification of the filler, which not only take advantage of its inherent advantages, but also improve the interface area with the epoxy matrix. The composite materials with excellent properties are expected to provide theoretical guidance for the application of high thermal conductivity dielectric materials.
研究领域:
材料科学
·
高分子化学
·
复合材料工程
·
电子封装材料
·
介电材料
·
热管理材料
✓ 已验证
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2022
·
IF 9.794
Wei Feng,Huirong Liu,Mingliang Zhao,Jianling Li,Feiyu Kang
The poly(ethylene oxide) based composite solid electrolyte(PEO-CSE) is an effective solution for developing high-performance solid-state lithium battery . However, the poly(ethlene oxide)(PEO) based solid-state lithium battery using 4.0 V cathode suffers from severe interfacial instability problems. In this work, we add additive lithium difluorophosphate(LiPO 2 F 2 ) into the PEO-CSE to form a stable and low resistance interphase at the cathode/electrolyte interface during charge/discharge process. The electrochemical stability window of PEO-CSE increases to ∼5.0 V. Besides, the electrochemical performance of PEO based solid-state lithium battery with LiCoO 2 as cathode is excellent. The discharge capacity of LiCoO 2 /Li cell with LiPO 2 F 2 reaches 108.5 mAh g −1 at 1.0C. In contrast, the discharge capacity that without LiPO 2 F 2 is only 60.0 mAh g −1 . Meanwhile, the PEO-CSE with LiPO 2 F 2 cell delivers stable cycle performance at 4.2 V. The capacity retention maintains 88.5% compared with 16.1%(without LiPO 2 F 2 ) after 100 cycles. Furthermore, it's still maintains 83.3% after 150 cycles. In addition, the cathode/electrolyte interface is analyzed by transmission electron microscope(TEM) and X-ray photoelectron spectroscopy(XPS). Galvanostatic intermittent titration test(GITT) is used to analyze the dynamic diffusion performance. This strategy provides a simple and effective way to improve the high voltage stability of the cathode/electrolyte interface.
研究领域:
电化学
·
材料科学
·
能源存储
·
固态电池
·
界面工程
✓ 已验证
DOI
高影响因子
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING
·
2018
·
IF 4.514
Yuxin He,Qiuyu Chen,Song Yang,Chang Lu,Mengting Feng,Yuanli Jiang,Guoxi Cao,Jianping Zhang,Chuntai Liu
The epoxy nanocomposites with Fe 3 O 4 modified graphene oxide (Fe 3 O 4 /GO) were used to influence the micro-cracks resistance of carbon fiber reinforced epoxy (CF/EP) laminate at 77 K. Fe 3 O 4 /GO with good paramagnetic properties were prepared by co-precipitation method and used to modify epoxy for cryogenic applications. Fe 3 O 4 /GO modified CF/EP laminates were also prepared through vacuum-assisted resin transfer molding (VARTM). The results show that the Fe 3 O 4 /GO can effectively improve the mechanical properties of epoxy (EP) matrix at 77 K and reduce the coefficient of thermal expansion (CTE) of EP matrix. It also can obviously improve the micro-cracks resistance of CF/EP composites at 77 K. Compared to neat EP, the CTE of Fe 3 O 4 /GO modified EP composite is decreased 51.6%. Compared to CF/EP composite, the micro-cracks density of Fe 3 O 4 /GO modified CF/EP composite at 77 K is decreased 60.0%.
研究领域:
材料科学
·
高分子复合材料
·
低温工程
·
纳米复合材料
·
力学性能
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）