Desalination and Water Treatment
·
2024
·
IF 1
Hongyuan Qin,Jiawei Huang,Xueli Zhang,Ling Yu,Yang Yu
In this study, lanthanum hydroxide adsorbent was synthesized through a simple hydrothermal method and applied for removing phosphate from water. The optimal adsorbent was obtained at the La/OH molar ratio of 4:1. The adsorbent showed rapid adsorption of phosphate within the first 4 h in which approximately 84% of the equilibrium adsorption capacity can be achieved. The phosphate uptake was highly dependent on solution pH. The better fit of the Langmuir isotherm model to experimental data indicated that the monolayer adsorption occurred and the maximum adsorption capacity of 193.9 mg/g was accomplished at pH 7.0. The presence of fluoride could significantly retard the uptake of phosphate. X-ray photoelectron spectroscopy analysis indicated that hydroxyl groups on the adsorbent surface played the most key role in the adsorption. The phosphate ions were adsorbed on the adsorbent through the formation of inner-sphere complexes.
研究领域:
环境化学
·
纳米材料科学
·
水污染控制
·
表面化学
·
吸附科学
✓ 已验证
DOI
高影响因子
CANADIAN JOURNAL OF CHEMICAL ENGINEERING
·
2015
·Vol. 94
·期 3
·424-429
·
IF 1.231
Xia Gui,Ying Ding,Zhi Yun
An integrated approach was developed for preparing epoxy fatty acid methyl esters (EFAMEs) from cottonseed using a two-phase solvent extraction (TPSE) process followed by sequential base-catalyzed transesterification and epoxidation reactions. The TPSE process was performed to achieve simultaneous production of high-quality crude cottonseed oil and nontoxic cottonseed meal. The base-catalyzed transesterification of the cottonseed oil proceeded smoothly at 30 °C over 2 h to provide a high yield of fatty acid methyl esters (FAMEs). Subsequent epoxidation of the unsaturated FAMEs using petroleum ether as a non-polar solvent, H 3 PO 4 as a catalyst, 0.3 g/g H 2 O 2 as an oxygen donor, and HCOOH as an oxygen carrier gave the corresponding EFAMEs with a conversion to oxirane of 0.85 g/g. The order of effectiveness of catalysts was found to be H 3 PO 4 > TiO 2 > H 2 SO 4 > strong-acid cation exchange resin. The bio-based integrated process and new methods for the preparation of modified EFAMEs show great promise for comprehensive development and commercial applications of cottonseed with fewer steps and lower cost.
研究领域:
应用化学
·
油脂化学
·
生物基材料
·
绿色化工
·
天然产物转化
✓ 已验证
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2015
·Vol. 132
·期 25
·
IF 1.768
Xiao-Hui Liu,Fei-Jun Zhang,Hui-Na Li,Xiao-Hui Hu,Wen-Li Di,Shuang Zhao
A facile, safe, and inexpensive reducing agent, sodium hypophosphite (NaH 2 PO 2 ·H 2 O), has been successfully used to perform ambient temperature living radical polymerizations of methyl methacrylate (MMA) and styrene (St). The rapid radical polymerizations were readily obtained at 25°C, i.e., MMA reached a conversion of ca 90% after 2.5 h, and St reached a conversion of ca 80% after 40 h. The polymerizations of MMA and St exhibited excellent living/controlled nature, as evidenced by pseudo first-order kinetics of polymerization, linear evolution of molecular weights with increasing monomer conversions, and narrow molecular weight distributions. The various experimental parameters—ligand, solvent, and molar ratio of NaH 2 PO 2 ·H 2 O to CuSO 4 ·5H 2 O—were varied to improve the control of polymerization, molecular weight, and molecular weight distribution. 1 H NMR analyses and chain-extension reactions confirm the high chain-end functionality of the resultant poly(methyl methacrylate) and polystyrene. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132 , 42123.
研究领域:
高分子化学
·
聚合反应工程
·
功能高分子材料
·
可控/活性聚合
·
绿色合成方法
✓ 已验证
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2015
·
IF 6.217
Zhantao Liu,Xusong Qin,Hui Xu,Guohua Chen
In this study, a one-pot sintering process incorporating sol–gel preparation route and in-situ carbon coating was proposed for the synthesis of carbon-coated nanosized LiTi 2 (PO 4 ) 3 . Experimental results show that the prepared LiTi 2 (PO 4 ) 3 particles are of high crystallinity and well-coated by turbostratic carbon. Attributed to nanosized particles and enhanced conductivity provided by turbostratic carbon coating, the carbon-coated LiTi 2 (PO 4 ) 3 showed high rate performance and good cycling life in aqueous electrolyte. Particularly, the carbon-coated LiTi 2 (PO 4 ) 3 exhibited initial specific capacities of 103 and 89 mAh g −1 , and retained 80.6% and 97% of the initial capacities after 120 cycles at 1C and 10C in aqueous electrolyte, respectively. The high rate performance and good cycling life of carbon-coated LiTi 2 (PO 4 ) 3 in aqueous electrolyte reveal its potential as negative electrode in aqueous lithium-ion batteries for electric vehicles and industrial-scale energy storage systems .
研究领域:
材料科学
·
电化学
·
能源存储
·
纳米技术
·
无机化学
✓ 已验证
DOI
高影响因子
Small
·
2022
·Vol. 18
·期 16
·2107346
·
IF 15.153
Ze Feng,Shan Zhang,Xiaobing Huang,Yurong Ren,Dan Sun,Yougen Tang,Qunxuan Yan,Haiyan Wang
Nickel-rich cathode materials, owing to their high energy density and low cost, are considered to be one of the cathodes with the most potential in next-generation lithium-ion batteries. Unfortunately, this kind of cathode with highly active surface is easy to react with H 2 O and CO 2 when exposed to ambient air, resulting in the formation of lithium impurities and interfacial phase transition as well as deterioration of the electrochemical properties. In this work, the evolution mechanism of the structure and interface of LiNi 0.8 Co 0.1 Mn 0.1 O 2 during air-exposure is systematically investigated. Furthermore, a facile reviving strategy is proposed to restore the degraded LiNi 0.8 Co 0.1 Mn 0.1 O 2 by using LiPO 3 as the repair agent. The lithium impurities on the surface of the degraded sample can transform into the repair/coating layer, and part of the rock salt phase on the subsurface can revive to layered phase after repair heat treatment. As a result, the optimized cathode delivers an initial discharge capacity of 198.3 mAh g −1 at 0.1C and a capacity retention of 85.5% after 50 cycles. Although slightly lower than the bare sample (201 mAh g −1 and 88%), they are obviously higher than the exposed samples (166.5 mAh g −1 and 40.4%). The regenerated electrochemical properties should be attributed to the multifunctional repair layer that can efficiently reduce the surface lithium impurities, prevent the corrosion of electrolyte, and improve the interfacial Li + diffusion kinetics. This work can effectively reduce the waste of the degraded Ni-rich ternary materials and realize the transformation of “waste” into wealth.
研究领域:
材料科学
·
电化学
·
能源存储
·
电池技术
·
界面工程
✓ 已验证
DOI
高影响因子
DESALINATION
·
2012
·
IF 2.59
Lei Ling,Yuming Zhou,Jingyi Huang,Qingzhao Yao,Guangqing Liu,Peixin Zhang,Wei Sun,Wendao Wu
In an attempt to control Ca 3 (PO 4 ) 2 , CaCO 3 , and CaSO 4 deposits in industrial recycling water systems, an acrylic acid (AA)-allyloxy poly(ethylene glycol) polyglycerol carboxylate (APEG-PG-COOH) copolymer was synthesized as a nonphosphorus inhibitor. The synthesized polymer was characterized by 1 H NMR. The performance of PAA/APEG-PG-COOH on inhibition of Ca 3 (PO 4 ) 2 , CaCO 3 and CaSO 4 precipitation was studied through static scale inhibition tests. It was shown that PAA/APEG-PG-COOH exhibited excellent ability to control inorganic minerals, with approximately 100% CaSO 4 inhibition and 99.89% Ca 3 (PO 4 ) 2 inhibition at levels of 3 and 6 mg/L PAA/APEG-PG-COOH, respectively. PAA/APEG-PG-COOH also displayed ability to prevent the formation of CaCO 3 scales. The effects on formation of Ca 3 (PO 4 ) 2 , CaCO 3 and CaSO 4 were investigated with combination of Scanning electronic microscopy (SEM), Transmission electron microscopy (TEM), and X-ray powder diffraction (XRD) analysis, respectively.
研究领域:
环境化学
·
材料科学
·
工业水处理
·
高分子化学
·
腐蚀与防护
·
矿物结垢控制
✓ 已验证
DOI
高影响因子
PROGRESS IN ORGANIC COATINGS
·
2020
·
IF 4.469
Haihua Wang,Wenjing Zhang,Yongning Ma,Guiqiang Fei,Huan Wen,Liyu Sun,Yanming Shao,Yong-Mook Kang
The compatibility between polypyrrole (PPy) and waterborne epoxy coating (EP) remains the main challenge. Here, phosphorylated poly (vinyl alcohol) (PPVA) and p-toluene sulfonic acid sodium (p-TSA) were simultaneously utilized as dopants to modify PPy and prepare water dispersible PPVA/p-TSA/PPy (PPVAT/PPy) solution. Additionally, poly (vinyl alcohol) (PVA) and TSA were also adopted to prepare PVA/p-TSA/PPy (PVAT/PPy) for comparison. Denser film with granular morphology was observed for PPVAT/PPy nanocomposite film. Compared with PVAT/PPy-40 %, the tensile strength of PPVAT-8.0 %/PPy-40 % increased from 248.8–283.9 MPa. PPVAT/PPy displayed higher compatibility and interactions with EP compared to PPy-TSA and PVAT/PPy. Compared with EP, the impedance modulus of PVAT/PPy+EP and PPVAT/PPy+EP increased from 3.17×10 5 to 1.07×10 8 and 1.62×10 9 Ω·cm 2 ; corrosion current density I corr decreased from 1.49×10 −6 to 7.72×10 -8 and 4.01×10 -9 A·cm -2 ; corrosion potential E corr displayed a positive shift of 230 mV and 269 mV, respectively. The corrosion inhibition efficiency of PPVAT/PPy+EP reached 99.83 %, which is much higher than that of PVAT/PPy+EP (93.97 %). PPVAT/PPy+EP nanocomposite coating has been proved to have preferable long-term corrosion resistance based on electrochemical impedance spectra (EIS), polarization curves and salt water spray test. The simultaneous incorporation of phosphate anions, sulfate ions and PPy into EP was beneficial to fabricate high-performance anticorrosion coating.
研究领域:
材料科学
·
高分子化学
·
腐蚀防护
·
纳米复合材料
·
表面工程
✓ 已验证
DOI
高影响因子
IONICS
·
2023
·Vol. 30
·期 2
·749-757
·
IF 2.8
Cong Jun,Luo Shao-hua,Li Peng-yu,Li Kun,Wang Ya-feng,Yan Sheng-xue,Li Peng-wei,Chen Huan-huan
To realize the high value–added utilization of acid-washed iron red, in this paper, acid-washed iron red is used as raw material. Aiming at the problem of low conductivity of iron-based lithium ion batteries (LIBs) LiFePO 4 /C materials, different metal ions are doped in the iron position, and the microstructure and electrochemical properties of the obtained material are systematically studied. Here, LiFePO 4 /C is synthesized through simple carbothermal reduction method using acid-washed iron red as the iron source. On this basis, La (1%, 2%, 3%) doping modification is carried out. Then doped modification is performed on this basis, preferably 2% La-doped LiFePO 4 /C materials. The XRD patterns show that the diffraction peaks of the samples prepared at all doping amounts can be perfectly matched with the standard card ( PDF # 40–1499), and there is no impurity peak, all of which are pure phases. According to the refined data, it is clear that minor amount of La has successfully replaced the position of Fe and incorporated into the lattice. Electrochemical tests show that LiFe 0.98 La 0.02 PO 4 /C has the highest charge and discharge capacity of 146.5/138.2 mAh·g −1 in the first cycle at 0.5C, and the reversible specific capacity of 136.5 mAh·g −1 remains after 50 cycles. Furthermore, the first-principles calculations more strongly confirm that La doping can significantly improve the defects of low electronic conductivity of LiFePO 4 .
研究领域:
材料科学
·
电化学
·
能源存储
·
无机非金属材料
·
固态化学
✓ 已验证
DOI
高影响因子
DESALINATION
·
2023
·
IF 9.9
Xudong Bu,Yurong Zhang,Haiqing Guo,Sheng Wang,Xueyan Du
The ion removal capacity of carbon based capacitive deionization (CDI) is limited by the double-layer mechanism. Replacing one electrode of the conventional carbon-based symmetric CDI with a battery-like ion insertion material to obtain hybrid capacitive deionization (HCDI) can significantly improve the adsorption capacity . Various ion insertion materials have been adopted for HCDI, however, how to optimize the performance of the HCDI system by matching the two electrodes with different ions removal mechanism remains challenging. In this work, a HCDI desalination cell was demonstrated by using NaTi 2 (PO 4 ) 3 /reduced graphene oxide composites (NTP-rGO-700) as the cathode and activated carbon (AC) as the anode. Based on the mass balance strategy of electrodes and the electrochemical behavior of hybrid capacitors with different AC:NTP-rGO-700 mass ratios, the HCDI desalination cell was assembled with the optimal AC:NTP-rGO-700 mass ratio of 2:1. At an operating voltage of 1.6 V and a current density of 125 mA·g −1 , the specific adsorption capacity (SAC) of the HCDI cell can reach 51 mg·g −1 with an average salt adsorption rate (ASAR) of 2 mg·g −1 ·min −1 , and the energy consumption (E m ) is 136.53 kJ·mol −1 . This work provides an efficient approach for developing high performance HCDI cell.
研究领域:
环境科学
·
电化学
·
材料科学
·
水处理技术
·
能源存储
✓ 已验证
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2015
·
IF 4.504
Peng Li,Lianyi Shao,Pengfei Wang,Xi Zheng,Haoxiang Yu,Shangshu Qian,Miao Shui,Nengbing Long,Jie Shu
In this work, Li 2 NaV 2 (PO 4 ) 3 is successfully synthesized by using a simple solid-state reaction method. Structural analysis shows that this sample is a hybrid product consisted of rhombohedral Li 3 V 2 (PO 4 ) 3 phase and rhombohedral Na 3 V 2 (PO 4 ) 3 phase As a cathode material for lithium ion batteries, Li 2 NaV 2 (PO 4 ) 3 exhibits an initial reversible capacity of 108.9 mAh g −1 at 35 mA g −1 in the potential range between 3.0 and 4.3 V, with an average working potential at 3.75 V. The lithium-ion diffusion coefficient in Li 2 NaV 2 (PO 4 ) 3 is measured to be 1.86–3.27 × 10 −15 cm 2 s −1 . In addition, the electrochemical reaction between Li 2 NaV 2 (PO 4 ) 3 and Li is also investigated by various in-situ and ex-situ techniques. Viewed from the in-situ and ex-situ results, it is concluded that the electrochemical reactions of Li 2 NaV 2 (PO 4 ) 3 with Li are associated with the formation of rhombohedral LiV 2 (PO 4 ) 3 phase and rhombohedral NaV 2 (PO 4 ) 3 phase during the lithium ion extraction process and its reverse lithium insertion process is reversible for structural evolution. The highly stable structure ensures the electrochemical reversibility of Li 2 NaV 2 (PO 4 ) 3 cathode material in lithium ion batteries.
研究领域:
材料科学
·
电化学
·
能源存储
·
无机化学
·
固体化学
✓ 已验证
DOI
高影响因子
Small
·
2023
·Vol. 19
·期 40
·2303227
·
IF 13.3
YuanZhe Wu,Quan Zong,Chaofeng Liu,Yanling Zhuang,Daiwen Tao,Jiangying Wang,Jingji Zhang,Qilong Zhang,Guozhong Cao
Vanadyl phosphate (VOPO 4 ·2H 2 O) has been regarded as one of the most promising cathode materials for aqueous Zn-ion batteries due to its distinct layered structure. However, VOPO 4 ·2H 2 O has not yet demonstrated the exceptional Zn ion storage performance owing to the structural deterioration during repeated charging/discharging process and poor intrinsic conductivity. In this work, 2D sodium vanadyl phosphate (NaVOPO 4 ·0.83H 2 O, denoted as NaVOP) is designed as a cathode material for Zn-ion batteries, in which sodium ions are preinserted into the interlayer, replacing part of water. Benefiting from the in situ surface oxidization, improved electronic conductivity, and increased hydrophobicity, the NaVOP electrode exhibits a high discharge capacity of 187 mAh g −1 at 0.1 A g −1 after activation, excellent rate capability and enhanced cycling performance with 85% capacity retention after 1500 cycles at 1 A g −1 . The energy storage mechanism of the NaVOP nanoflakes based on the rapid Zn 2+ and H + intercalation pseudocapacitance are investigated via multiple ex situ characterizations.
研究领域:
材料科学
·
电化学
·
能源存储
·
无机化学
·
纳米材料
✓ 已验证
DOI
高影响因子
BIOSENSORS & BIOELECTRONICS
·
2017
·
IF 7.78
Chao Liu,Jing Dong,Geoffrey I.N. Waterhouse,Ziqiang Cheng,Shiyun Ai
A sensitive sandwich-type electrochemical immunosensor was developed for the detection of avian leukosis virus subgroup J (ALV-J), which benefitted from multiple signal amplification involving graphene-perylene-3,4,9,10-tetracarboxylic acid nanocomposites (GR-PTCA), nanocellulose-Au NP composites (NC-Au) and the alkaline phosphatase (ALP) catalytic reaction . GR-PTCA nanocomposites on glassy carbon electrodes served as the immunosensor platform. Due to their excellent electrical conductivity and abundant polycarboxylic sites, the GR-PTCA nanocomposites allowed fast electron transfer and good immobilization of primary antibodies, thereby affording a strong immunosensor signal in the presence of ALV-J. The detected signal could be further amplified by the introduction of NC-Au composites as a carrier of secondary antibodies (Ab 2 ) and by harnessing the catalytic properties of Au and ALP. Under optimized testing conditions, the electrochemical immunosensor displayed excellent analytical performance for the detection of ALV-J, showing a linear current response from 10 2.08 to 10 4.0 TCID 50 /mL (TCID 50 : 50% tissue culture infective dose) with a low detection limit of 10 1.98 TCID 50 /mL (S/N = 3). In addition to high sensitivity, the immunosensor showed very good selectivity, reproducibility and operational stability, demonstrating potential application for the quantitative detection of ALV-J in clinical diagnosis.
研究领域:
免疫学
·
生物传感器
·
分子诊断
·
兽医病毒学
·
纳米医学
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）