International Journal of Electrochemical Science
·
2023
·
IF 1.5
Yong Lu,Huixia Feng,Hou Xia,Wu Hai Xia
Polyaniline has a wide application in the field of corrosion protection, the poor solubility of polyaniline limited its application as a corrosion inhibitor. Water-soluble carboxymethyl cellulose -polyaniline composites was synthesized by chemical oxidation polymerization in a mild way without other inorganic or organic acids added. Corrosion inhibition performance of composites was evaluated for Q235 steel corrosion in 1 M HCl corrosive solution using weight loss and electrochemical measurements at various concentrations. The results show that carboxymethyl cellulose -polyaniline composites exhibit good inhibition properties and the remarkable increase in inhibition efficiency, i.e., 94.24% is achieved while the maximum concentration of the experiment is 1000 ppm. The composites in corrosive solution suppress the cathodic hydrogen evolution reactions and anodic metal dissolution of the substrate. Adsorption of the inhibitor on the steel surface follows a Langmuir adsorption isotherm.
研究领域:
材料科学
·
腐蚀与防护
✓ 已验证
DOI
高影响因子
Surface Topography-Metrology and Properties
·
2017
·Vol. 5
·期 4
·044001
·
IF 0
Xiangyu Li,Yuwei Ye,Tong Liu,Wenru Zheng,Feng Yang,Haichao Zhao,Liping Wang
Novel quaternary ammonium cation containing tetraaniline (QATA) was successfully synthesized by condensation of amine-capped tetraaniline with 6-bromohexanoic acid, followed by quaternarization with triethylamine. The corrosion inhibition performance of QATA with their adsorption mechanisms for Q235 steel was studied in 1 M HCl solution by a series of methods such as weight loss measurements, potentiodynamic polarization, electrochemical impedance spectroscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and atomic force microscopy (AFM). The inhibition efficiency (IE%) increased with increasing concentrations of QATA, reaching a value up to 97.47% at a concentration of 150 mg l−1. Potentiodynamic polarization curves showed that the QATA affected both cathodic and anodic protection and was a mixed type inhibitor in 1 M HCl corrosive medium. Adsorption isotherm studies confirmed that the absorption of QATA on the Q235 steel surface in 1 M HCl solution obeyed Langmuir adsorption isotherm, and the adsorption process of corrosion inhibition on Q235 steel surface involved both the physical and chemical adsorption. The EDS analysis determined the adsorption of QATA molecules on the steel surface, the surface morphologies before and after immersion in 1 M HCl medium were also investigated by SEM and AFM.
研究领域:
材料科学
·
腐蚀与防护
·
电化学
✓ 已验证
产品关联
DOI
Surfaces and Interfaces
·
2025
·
IF 6.3
Jianyang Liu,Wei Wang,Zhipeng Mao,Lin Cao,Meiyan Yu,Shougang Chen
Metal corrosion and rusting have caused significant losses to humans, and environmentally friendly and efficient rust removal methods are receiving increasing attention. Here, we propose a method for rust removal by synthesizing acrylic gel on Q235 steel sheet using a photopolymerization reaction. The weak acidity of acrylic acid decomposes rust, and the gel formed by the reaction of acrylic acid with acrylamide has strong adsorption capacity, which effectively adsorbs rust molecules and metal ions. The introduced Cu 2 O enhances the rust removal system. Cu 2 O reacts with the acrylic acid monomer to form a monovalent copper complex, which can improve the rust removal efficiency during the process through redox reactions. The UV-induced copolymerization of acrylic monomers to form gel enables effective rust removal, with a rust removal rate as high as 85.94 g ·h –1 ·m –2 . This method avoids the use of strong acids commonly found in traditional rust removal methods, offering advantages such as environmental friendliness and low cost. The gel formed during the rust removal process can be easily and conveniently removed from the substrate surface, thus avoiding secondary pollution issues such as waste liquid disposal.
研究领域:
材料科学
·
腐蚀与防护
·
环境工程
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF INDUSTRIAL AND ENGINEERING CHEMISTRY
·
2022
·
IF 6.76
Yue Wang,Yujie Qiang,Hui Zhi,Boyuan Ran,Dawei Zhang
In recent years, many plant extracts have been used as green corrosion inhibitors to replace traditional corrosion inhibitors, but their inhibition performance still needs to be improved. The synergistic corrosion inhibition behavior and mechanism of maple leaves extract (MLE) and potassium iodide (KI) on Q235 steel in 0.5 M H 2 SO 4 solution were firstly investigated in this work. The results demonstrate that both MLE and KI can prevent the corrosion of steel in corrosive media, and that their combined protection effect is superior. The corrosion inhibition efficiency ( η ) value reaches 93.4 % in corrosive solution with the combination of 200 mg/L MLE and 200 mg/L KI, while the maximum of η is only 81.6 % using MLE alone. In addition, Fe-N bond and Fe-O bond were found on the steel surface through the X-ray photoelectron spectroscopy (XPS) analysis, which confirm the formation of a protective film. The adsorption behavior of an inhibitory film composed of MLE and KI mixtures onto steel surface follows the Langmuir adsorption isotherm model, consisting of physisorption and chemisorption. Finally, molecular dynamics (MD) simulation indicates that inhibitor molecules can adsorb on the Fe substrate in a parallel way with high binding energy values, which supports the experiments well.
研究领域:
材料科学
·
绿色化学
·
表面化学
✓ 已验证
产品关联
DOI
高影响因子
ACS Omega
·
2021
·
IF 3.512
Bianli Quan,Junqi Li,Chaoyi Chen
This study investigates the effect of corrosion temperature on the corrosion of Q235 steel and 16Mn steel in the sodium aluminate solution using the weight loss method and electrochemical method. The results indicate that the corrosion rates of two steels show an increasing trend with the temperature and that of Q235 steel increases more than that of 16Mn steel at higher temperatures. The corrosion products have changed from four forms at 25 °C to two forms at 65 and 110 °C, namely, the octahedral particles and the bulk particles formed by the flocculent aggregation. The corrosion products are composed of FeS, FeS2, Fe2O3, Fe3O4, NaFeO2, and Al2O3. The Icorr of the two steels increases with temperature, while Rp gradually decreases. The two steels are controlled by the charge transfer at 25 and 65 °C and the charge transfer and the ion diffusion at 95 °C, indicating that the temperature changes the kinetics of the corrosion process.
研究领域:
材料科学
·
电化学
✓ 已验证
DOI
高影响因子
LANGMUIR
·
2022
·
IF 4.331
Lei Guo,Mengyue Zhu,Zhongyi He,Renhui Zhang,Savaş Kaya,Yuanhua Lin,Viswanathan S. Saji
N and S codoped carbon dots having good water solubility have been successfully made by a novel hydrothermal method and characterized by FTIR, XPS, and TEM. The as-synthesized CDs were carbon particles rich in polar functional groups less than 10 nm in size. Electrochemical measurements, gravimetry, and surface analysis methods were utilized to examine the inhibition characteristics and adsorption mechanism of CDs on the carbon steel in acid pickling solutions. Electrochemical measurements verified that the CDs displayed adequate protection with high inhibition efficiency of 97.8%. The long-term weight-loss experiments up to 72 h further confirmed the excellent corrosion inhibition at room temperature and 313 K. The results presented are helpful for the formulation of more effective acid pickling corrosion inhibitors.
研究领域:
材料科学
·
腐蚀与防护
✓ 已验证
产品关联
DOI
PubMed
高影响因子
APPLIED SURFACE SCIENCE
·
2021
·
IF 6.707
You Wu,Yangyang Duan,Juan Qiu,Xiang Gao,Houyi Ma
The aim of this work is to develop an eco-friendly pH-responsive intelligent coating with long-term corrosion protection by a convenient method. Herein, an eco-friendly and long-term pH-responsive intelligent anti-corrosion coating (BTA-CaCO 3 @TA coating) is fabricated through the addition of a hydrophilic pH-responsive release material (BTA-CaCO 3 @TA microspheres) into a waterborne epoxy resin coating. The electrochemical impedance spectroscopy results indicated that BTA-CaCO 3 @TA microspheres could endow the coating with long-term corrosion protection. The |Z| f =0.01Hz values of the BTA-CaCO 3 @TA coating after 130 days of immersion were still higher than those of the pure waterborne epoxy resin coating at the beginning of immersion. The excellent long-term protection performance was related to the good dispersibility of BTA-CaCO 3 @TA microspheres in the waterborne coatings, the TA conversion film and the BTA inhibitor protection film, which formed on the steel surface in situ. This synergistic strategy demonstrated its future application for protecting metals from corrosion.
研究领域:
材料科学
·
腐蚀与防护
·
化学工程
✓ 已验证
产品关联
DOI
高影响因子
International Journal of Electrochemical Science
·
2023
·
IF 1.5
Yong Lu,Huixia Feng,Haidong Xu
A green phytic acid film was prepared on the steel surface before the natural garlic extract was used for the post-treatment of the conversion coating. Then scanning electron microscopy (SEM) equipped with X-ray energy dispersive spectrum (EDS) were adopted for micro-morphology and elemental composition determination of different samples. Atomic force microscopy (AFM) and contact angle measurement were used to assess the adhesion properties of the prepared coating. At last, the electrochemical characteristic of the coating on the Q235 steel was examined using electrochemical impedance spectroscopy (EIS) and polarization curves in a 3.5 wt. % NaCl. SEM and AFM studies have shown that a homogenous, flake-like coating with lower crack was deposited on the steel surface. Particularly, EIS studies have shown that the anti-corrosion performance of the coating that treated with the garlic extract was markedly improved. Simultaneously, the adhesion property with the subsequent coating adhesion was also increased.
研究领域:
材料科学
·
表面工程
·
电化学
·
绿色化学
✓ 已验证
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2021
·
IF 8.128
Mengyue Zhu,Lei Guo,Zhongyi He,Riadh Marzouki,Renhui Zhang,Elyor Berdimurodov
N -doped carbon quantum dots (NCQDs) were synthesized by a hydrothermal method using folic acid and o-phenylenediamine as precursors. The inhibition behaviour of the NCQDs on Q235 steel in 1 M HCl solution was appraised through electrochemical impedance spectroscopy (EIS), potentiodynamic polarization curves (PDP), and surface analysis. The results demonstrated that the synthesized NCQDs had an effective anticorrosion effect on Q235 steel, and the corrosion inhibition efficiency of 150 mg/L NCQDs reached 95.4%. Additionally, the analysis of the PDP corrosion potential changes indicated that the NCQDs acted as a mixed corrosion inhibitor. Moreover, the NCQDs adsorbed onto the surface of steel by coordinating its electron-rich atoms with the iron metal to form a protective film, which slowed the dissolution reaction of the anodic metal to achieve corrosion inhibition. The adsorption mechanism of the NCQDs was consistent with Langmuir adsorption, including physical and chemical adsorption. Therefore, this work can inspire and facilitate, to a certain extent, the future application of doped carbon quantum dots as efficient corrosion inhibitors in pickling solutions.
研究领域:
材料科学
·
电化学
·
防腐蚀研究
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ANTI-CORROSION METHODS AND MATERIALS
·
2024
·Vol. 71
·期 4
·391-402
·
IF 2.3
Hang Jia,Zhiming Gao,Shixiong Wu,Jia Liang Liu,Wenbin Hu
PurposeThis study aims to investigate the corrosion inhibitor effect of migrating corrosion inhibitor (MCI) on Q235 steel in high alkaline environment under cathodic polarization.Design/methodology/approachThis study investigated the electrochemical characteristics of Q235 steel with and without MCI by polarization curve and electrochemical impedance spectroscopy. Besides, the surface composition of Q235 steel under different environments was analyzed by X-ray photoelectron spectroscopy. In addition, the migration characteristic of MCI and the adsorption behavior of MCI under cathodic polarization were studied using Raman spectroscopy.FindingsDiethanolamine (DEA) and N, N-dimethylethanolamine (DMEA) can inhibit the increase of Fe(II) in the oxide film of Q235 steel under cathodic polarization. The adsorption stability of DMEA film was higher under cathodic polarization potential, showing a higher corrosion inhibition ability. The corrosion inhibition mechanism of DEA and DMEA under cathodic polarization potential was proposed.Originality/valueThe MCI has a broad application prospect in the repair of damaged reinforced concrete due to its unique migratory characteristics. The interaction between MCIs, rebar and concrete with different compositions has been studied, but the passivation behavior of the steel interface in the presence of both the migrating electric field and corrosion inhibitors has been neglected. And it was investigated in this paper.
研究领域:
材料科学
·
电化学
✓ 已验证
产品关联
DOI
高影响因子
Metals
·
2023
·Vol. 13
·期 4
·649
·
IF 2.9
Xiaoxi Ruan,Linlin Yang,Yan Wang,Yizhe Dong,Dake Xu,Mingxing Zhang
The corrosion of carbon steel causes dramatic economic losses each year. Since conventional corrosion prevention approaches may cause pollution problems to the environment, ecofriendly and effective corrosion approaches are desired. Microbiologically influenced corrosion inhibition (MICI) has been reported as a sustainable corrosion prevention method. This work aims to evaluate the corrosion inhibition effect of two bacterial strains,Tenacibaculum mesophilumD-6 andBacillussp. Y-6 by choosing Q235 carbon steel as a model system. Scanning electron microscopy (SEM), confocal laser scanning microscopy (CLSM) and a series of electrochemical techniques were applied to study the corrosion prevention effect. The electrochemical and pitting results indicated thatT. mesophilumD-6 displayed a better corrosion protection effect.T. mesophilumD-6 formed a denser and thicker biofilm on the Q235 surface thanBacillussp. Y-6. The maximum thickness of theT. mesophilumD-6 biofilms was 11.6 ± 0.7 μm, which is about twice as thick than that ofBacillussp. Y-6. The corrosion prevention mechanism was ascribed to the formation of biofilms as a barrier to block corrosive agents such as O2. This study provides a theoretical foundation for the application of biofilms as green and effective corrosion inhibitors for carbon steel.Keywords:Q235 carbon steel;Tenacibaculum mesophilumD-6;Bacillussp. Y-6;corrosion inhibition;biofilm formation ability
研究领域:
微生物学
·
材料科学
·
腐蚀工程
✓ 已验证
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2024
·
IF 2.7
Yongning Ma,Panpan Li,Peihan Wu,Mingyuan Guo,Yuhao Yang,Xiaolong Li
In photocatalytic anticorrosion perspective, the migration rate of excited electrons from surface layers to substrate steels restricted the performance of g-C 3 N 4 due to the high resistance between interface of g-C 3 N 4 layers and adhesive layers. Herein, an S-scheme g-C 3 N 4 /polyaniline (PANI) heterojunction with face-to-face structure was established by a secondary calcining method. The as-prepared heterojunctions were applied to protect Q235 carbon steel, and the results showed that the anticorrosion performance of S-scheme g-C 3 N 4 /PANI heterojunction is much higher than that of g-C 3 N 4 and PANI coating layers according to salt spray test. Photocurrent intensity indicated that the optimum amounts of g-C 3 N 4 and PANI were 0.06 and 0.09 mL/cm 2 , which are benefit for the transport of excited electrons due to the optimum thickness of coating layers. Furthermore, the S-scheme g-C 3 N 4 /PANI heterojunction can promote the separation rate of charge carriers and suppress the recombination rate at the same time, which are inferred from photocurrent intensity, electrochemical impedance spectra, super-depth-of-field microscope, and photoluminescence investigation. In the last, the enhanced anticorrosion performance of S-scheme g-C 3 N 4 /PANI heterojunction with face-to-face structure was deduced according to mentioned characterization.
研究领域:
材料科学
·
腐蚀与防护
·
光催化
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）