ADVANCED FUNCTIONAL MATERIALS
·
2022
·Vol. 32
·期 39
·2203528
·
IF 19.924
Qiuni Zhao,Wenzhe Zhou,Mingxiang Zhang,Yang Wang,Zaihua Duan,Chaoliang Tan,Bohao Liu,Fangping Ouyang,Zhen Yuan,Huiling Tai,Yadong Jiang
Endowed with rich terminal groups, good electrical conductivity, and controllable structure, transition metal carbides/nitrides (MXenes) have attracted extensive attention for potential application in gas sensor, but long-standing challenges of the MXenes (titanium carbide as the representative) are their limited selectivity and sensitivity. Herein, a high-active double transition-metal titanium molybdenum carbide (Mo 2 TiC 2 T x ) with superstrong surface adsorption (−3.12 eV) for NO 2 gas molecule is proposed, and it is further coupled with molybdenum disulfide (MoS 2 ) by interface modulation to construct an edge-enriched heterostructure. Due to the synergistic effect of strong adsorption, rich adsorption sites, and coupling interface of Mo 2 TiC 2 T x /MoS 2 composite, the as-fabricated Mo 2 TiC 2 T x /MoS 2 gas sensor exhibits an outstanding response toward NO 2 with high selectivity against various interference gases, which is well supported by density functional theory calculations. Meanwhile, the sensor exhibits a sensitivity of 7.36% ppm −1 , detection limit of 2.5 ppb, and reversibility at room temperature. A portable, wireless NO 2 monitoring system is demonstrated for gas leakage searching and dangerous warning based on Mo 2 TiC 2 T x /MoS 2 gas sensor. This work facilitates the gas sensing application of MXenes, and provides an avenue for the development of wireless sensing system in environmental monitoring and safety assurance.
✓ 已验证
产品关联
DOI
高影响因子
Biomedical Materials
·
2022
·Vol. 17
·期 4
·045025
·
IF 4.103
Mingchao Jin,Juli Zhu,Zhipeng Meng,Xuesheng Jiang,Zhuo Chen,Juntao Xu,Hongliang Gao,Junkun Zhu,Fengfeng Wu
Titanium dioxide (TiO2), as one of the titanium (Ti)-based implants, holds a promise for a variety of anti-bacterial application in medical research. In the current study, a functional molybdenum disulfide (MoS2)/polydopamine (PDA)-LL-37 coating on titanium dioxide (TiO2) implant was prepared. Anodic oxidation and hydrothermal treatment was given to prepare TiO2 nanotubes-MoS2/PDA-LL-37 (T-M/P-L). The in vitro osteogenic effect of T-M/P-L was evaluated by measuring mesenchymal stem cell (MSC) adhesion, proliferation, alkaline phosphatase (ALP) activity, extracellular matrix (ECM) mineralization, collagen secretion and osteoblast-specific messenger RNAs (mRNAs) expression. The determination on the anti-bacterial ability of T-M/P-L was followed. Furthermore, the ability of T-M/P-L to promote bone formation in vivo was evaluated. Near-infrared (NIR) laser irradiation exposure enabled the T-M/P-L coating-endowed Ti substrates to hold effective anti-bacterial ability. T-M/P-L promoted the adhesion and proliferation of MSCs. In addition, an increase was witnessed regarding the ALP activity, collagen secretion and ECM mineralization, along with the expression of runt-related transcription factor 2, ALP and osteocalcin in the presence of T-M/P-L. Additionally, T-M/P-L could stimulate endothelial cells to secrete vascular endothelial growth factor (VEGF) and promote capillary-like tubule formation. Upon NIR laser irradiation exposure, T-M/P-L not only exhibited efficient in vivo anti-bacterial activity but also facilitated new bone formation. Collectively, T-M/P-L had enhanced anti-bacterial and osteogenic activity under NIR laser irradiation.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2022
·
IF 16.744
Yuanwu Liu,Huai Zhang,Weiming Song,Ying Zhang,Zhipeng Hou,Guofu Zhou,Zhang Zhang,Junming Liu
Improving water adsorption and hydrogen (H) atoms desorption capacities are critical issues for the hydrogen evolution reaction (HER) in alkaline media. Herein, a ReS 2 /NiS heterostructure was generated in situ on the surface of the nickel foam (NF) using a facile hydrothermal process. The combination of experimental and density functional theory (DFT) analyses revealed a charge transfer from NiS to ReS 2 , which directly promoted water adsorption on Ni sites in NiS as well as H desorption on S sites in ReS 2 . Moreover, the antioxidation capacity of the heterointerface in the catalyst improved. Therefore, the formed ReS 2 /NiS@NF delivered an excellent HER activity very close to that of commercial Pt/C at low current density with overpotential of 78 mV at 10 mA/cm 2 while remarkably outperforming Pt/C at high current densities. The ReS 2 /NiS@NF also exhibited remarkable stability at 150 mA/cm 2 . This work provides a strategy for designing excellent electrocatalysts based on NiS.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Semiconductors
·
2022
·Vol. 43
·期 9
·092201
·
IF 0
Chen Gao,Hui Wang,Pang Wang,Jinlong Cai,Yuandong Sun,Cong Yu,Teng Li,Xiaoshuai Zhang,Dan Liu,Tao Wang
Defects as non-radiative recombination centers hinder the further efficiency improvements of perovskite solar cells (PSCs). Additive engineering has been demonstrated to be an effective method for defect passivation in perovskite films. Here, we employed (4-methoxyphenyl) potassium trifluoroborate (C7H7BF3KO) with {{\rm{BF}}_3^-} and K+ functional groups to passivate spray-coated (FAPbI3)x(MAPbBr3)1–x perovskite and eliminate hysteresis. It is shown that the F of {{\rm{BF}}_3^-} can form hydrogen bonds with the H atom in the amino group of MA+/FA+ ions of perovskite, thus reducing the generation of MA+/FA+ vacancies and improving device efficiency. Meanwhile, K+ and reduced MA+/FA+ vacancies can inhibit ion migration, thereby eliminating hysteresis. With the aid of C7H7BF3KO, we obtained hysteresis-free PSCs with the maximum efficiency of 19.5% by spray-coating in air. Our work demonstrates that additive engineering is promising to improve the performance of spray-coated PSCs.
✓ 已验证
产品关联
DOI
Coatings
·
2022
·Vol. 12
·期 9
·1235
·
IF 3.236
Qi Hu,Jiantao Niu,Ke-Qin Zhang,Mu Yao
The photocatalytic hydrogen production efficiency of a single SrTiO3photocatalytic catalyst is often low, which is mainly due to the serious combination of electrons and holes produced by photocatalysis as well as the mismatch of the redox capacity and light absorption range. Construction of semiconductor heterojunctions can solve these problems. CdS has a narrow band gap, which can effectively utilize visible light, and it has a band structure matched with that of SrTiO3. Therefore, CdS is considered as an ideal candidate for constructing heterojunctions with SrTiO3. In this paper, bamboo pulp fibers were used as the substrate, and SrTiO3was coated on the substrate through the solvothermal process. CF/SrTiO3rich in oxygen vacancies was formed by high temperature carbonization, and heterojunctions were formed by loading CdS on the surface of the CF/SrTiO3composite material through the hydrothermal method, thus obtaining one-dimensional CF/SrTiO3/CdS core–shell photocatalysts. The structure and photocatalytic hydrogen production performance of the CF/SrTiO3/CdS core–shell photocatalysts were mainly studied. The photocatalytic hydrogen production experiment showed that the hydrogen production rate of the CF/SrTiO3/CdS-2 sample under the optimized process was as high as 577.39 μmol/g·h, which was about 11 times that of the CF/SrTiO3sample. In this composite photocatalytic material system, the loading of the CdS nanospheres could enhance the visible light absorption capacity of the composite catalyst, promote the rapid separation and high-speed migration of photocarriers, and significantly improve the photocatalytic activity.Keywords:SrTiO3;photocatalytic;hydrogen production;carbon fiber;oxygen vacancy;CdS
✓ 已验证
产品关联
DOI
高影响因子
ANALYTICAL AND BIOANALYTICAL CHEMISTRY
·
2022
·Vol. 414
·期 19
·5917-5928
·
IF 4.478
Zuo Jiabao,Shen Yuliang,Gao Juanjuan,Song Haiou,Ye Zhiwen,Liang Ying,Zhang Shupeng
Flexible sensing is an alternative to traditional sensing and possesses good flexibility and wearability. Intrinsically conductive polymers, particularly poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS), have received significant attention due to their high mechanical flexibility and good biocompatibility. Here, we report the design of highly conductive and electrochemically active PEDOT:PSS-coated plastic substrate electrodes by combining N-doped graphene (NG) or S-doped graphene (SG) with methanesulfonic acid-treated PEDOT:PSS (denoted as NG-f-MSA-PEDOT:PSS/PET and SG-f-MSA-PEDOT:PSS/PET) by a simple drop-coating method. At room temperature, the NG-f-MSA-PEDOT:PSS/PET electrode demonstrated the lowest detection limits of 17.09, 33.84, 28.30, and 44.96 nM for paracetamol, uric acid, dopamine, and catechol (S/N = 3), respectively. The NG-f-MSA-PEDOT:PSS/PET electrode had good anti-interference ability and reproducibility without employing expensive noble metals and requiring much effort to polish the surface of traditional glass carbon electrodes. Most importantly, this film electrode could maintain a stable electrochemical response under different bending and crease states and had excellent mechanical stability and flexibility. Graphical abstract
✓ 已验证
产品关联
DOI
PubMed
高影响因子
APPLIED SURFACE SCIENCE
·
2022
·
IF 7.392
Xiandi Cui,Zhiquan Yang,Xinyi Zhang,Wanhui Liu,Baosheng Zou,Wenning Liao
As an effective treatment method for uranium removal in wastewater, the application of photocatalytic reduction has attracted extensive attention. To improve the optical performance of Nb 2 O 5 , CdS nanoparticles were introduced via a one-step hydrothermal method. Then the characterization by various methods (e.g. XRD, SEM, TEM, XPS and UV–vis DRS) were used to determine the structural and optical properties of the heterojunction of Nb 2 O 5 nanorod/CdS nanoparticles (NC). It clearly confirmed that the successful construction of the heterojunction widened the visible light absorption range, narrowed bandgap (∼2.11 eV), promoted the charge transfer and enhanced the separation efficiency of photoinduced electron-hole pairs and further improved the photoreduction activity. During the photocatalytic degradation process, the results showed the photocatalyst with the Nb/Cd molar ratio of 1/3 (NC-3) displayed the best removal of U(VI), with a removal efficiency of 97% in 90 min adsorption and 150 min visible light irradiation at the pH=6. The NC-3 photocatalyst was relatively stable and exhibited good recyclability in during the cyclic experiments. In the end, it was proposed that e - and O 2 - radicals played important roles in the process of the reduction of U(VI).
✓ 已验证
产品关联
DOI
高影响因子
Journal of Materials Chemistry A
·
2022
·Vol. 10
·期 28
·14954-14964
·
IF 14.511
Hao Liu,Haochang Chen,Shunzhe Zhang,Kaifeng Wang,Lei Yang,Yujie Chen,Hezhou Liu,Hua Li
Combining two distinct materials to obtain high-performance electrode materials is a viable solution, but the process is inefficient, taking at least two processes and requiring tens of hours. Here, a unique bipolar pulse electrodeposition process is proposed, which effectively manufactures a composite electrode material with strong synergistic connection between NiCoS and PPy in a single step. Taking advantage of the synergistic impact of the nickel–cobalt sulfide nanoflower structure with a wide electrode–electrolyte contact area, as well as PPy with the appropriate thickness, the composite NiCoS/PPy electrode exhibits a high specific capacitance of 1848.8 F g−1 at a current density of 1 A g−1 and excellent rate performance. Due to the strong-coupling and the protection of the PPy layer, the electrode material possesses ultra-high cycling stability at high current density (96.15% capacitance retention after 10 000 cycles at 10 A g−1). When compared to other typical methods, this approach greatly simplifies the composite electrode material production process, requiring just one step and 2400 seconds, which is hundreds of times faster. Furthermore, an assembled asymmetric supercapacitor (ASC) device of NCS/P-3//activated carbon (AC) achieves a high energy density of 48.79 and 40.21 W h kg−1 at a power density of 750 and 7500 W kg−1, respectively, while maintaining a long cycle-life. It is proved that on the premise of simplifying the preparation process by bipolar pulse electrodeposition, the composite electrode material has excellent electrochemical properties and can be used in high-capacity asymmetric supercapacitors.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2022
·Vol. 33
·期 19
·15754-15762
·
IF 2.779
Zhang Ting,Chu Xueying,Jin Fangjun,Xu Mingze,Zhai Yingjiao,Li Jinhua
Sensors for rapid and reliable detection of biomolecules are crucial for clinical medical diagnoses. Here, a rapid, ultra-sensitive, magnetic-assisted biosensor based on resonance Raman scattering at MoS 2 @Fe 3 O 4 composite nanoflowers is presented. Raman shifts and X-ray photoelectron spectra indicated that the composite was formed via Fe–S covalent bonds. Convenient magnetic separations could be performed because of the superparamagnetic Fe 3 O 4 nanoparticles. MoS 2 E 1 2g and A 1g Raman peaks were used as probe signals for anti-interference immunoassays. The probe unit of the immunoassay also included goat anti-human IgG molecules that were used as the target analyte. Au substrates coupled with the goat anti-human IgG were used as capture units to form sandwich biosensors. Because of the magnetic enrichment, the detection limit was improved by three orders-of-magnitude and the detection time was reduced from 1.5 h to 1 min. Sandwich biosensors using MoS 2 @Fe 3 O 4 nanoflowers as Raman probes could be very promising sensors for proteins, antigens, and other immunogenic biopolymers, as well as for corpuscular viruses and cells.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2022
·
IF 4.326
Yunxia Bai,Mei Li,Xuemei Liu,Jinyu Han,Xinli Zhu,Qingfeng Ge,Hua Wang
Photocatalytic CO2 reduction is a promising route to simultaneously address two critical issues related to the energy and environment. Herein, a direct Z-scheme photocatalytic system, Ti3+ defective TiO2/CdS nanoflowers, was fabricated to enhance the production of C1–C3 products from CO2 reduction. First, nanoflower-like TiO2 (NF-TiO2) is prepared using a TiB2 precursor to build in Ti3+ defects. Then, the NF-TiO2/CdS heterojunctions are constructed via the sulfurization of TiO2/Cd-MOF. Importantly, the optimal heterojunction photocatalyst NF-TiO2/CdS0.6 exhibits a highly promoted CO2 reduction activity not only for CO and CH4 but also for C2–C3 hydrocarbons. The cumulative yields of CO and CH4 are 1007.0 μmol/g and 83.5 μmol/g (2.5 h), respectively, and a yield of 55.3 μmol/g (2.5 h) of C2–C3 hydrocarbons is obtained. This enhanced yield of C1–C3 products is attributed to the synergistic effects of abundant Ti3+ defects that increase adsorption and activation of CO2, the large surface area that provides sufficient active sites, and a direct Z-scheme heterojunction with a good intimate contact interface that effectively separates charge carriers and accumulates electrons with strong reducibility. Moreover, the photoluminescence analysis of hydroxyl radicals was conducted to provide evidence for the direct Z-scheme mechanism. This work provides a facile method for the construction of a TiO2-based direct Z-scheme photocatalytic system for improving photocatalytic performance toward CO2 reduction.
✓ 已验证
产品关联
DOI
高影响因子
Nanomaterials
·
2022
·Vol. 12
·期 12
·2087
·
IF 5.719
Xinman Tu,Linhong Ge,Lamei Deng,Li Zhang
Metal sulfide is often utilized as a catalyzed material to form colorimetric response system for some heavy metal detection. While the aggregation effect and conventional morphology limited the catalyzed efficiency. Herein, a robust method based on morphology adjustment was proposed to improve the dispersibility and catalytic performance of CuS. The results demonstrated when the solvent ratio of ethylene glycol and dimethyl sulfoxide arrived at 3:1, it displayed an optimal structure which is like a patulous flower. Meanwhile, an optimal surface binding energy (ΔE) of 120.1 kcal/mol was obtained via theoretical calculation model. The flower-like structure caused a 2-fold increase in the catalytic level. Subsequently, the CuS was employed to make colorimetric detection of Cr(VI) in water. The assay results exhibited a linear range of the Cr(VI) from 60 to 340 nM, the limit of detection was 1.07 nM. In the practical tests for Qianhu lake water, the spiked recoveries were 93.6% and 104% with the RSD of 4.71% and 3.08%. Therefore, this CuS-based colorimetric method possesses a satisfactory application prospect for the Cr(VI) determination in water.Keywords:CuS;morphology adjustment;solvent ratio;Cr(VI);colorimetric detection
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2022
·
IF 16.744
Xuyan Zhang,Pengfei Cheng,Weiming Song,Shiya Rong,Jieming Huang,Dong Wang,Peter Schaaf,Guofu Zhou,Zhang Zhang,Junming Liu
Solar energy is a promising renewable energy with the potential for the sustainable development of the world. Efficient photo-thermal conversion is essential for harvesting and conversion of solar energy, therefore, the main challenge is the development of efficient and low-cost photothermal conversion materials. Carbon framework can be considered as a candidate but somehow its application potential can be still constrained due to the limited absorption of near-infrared (NIR) light. Herein, we propose a general strategy for preparing two-dimensional (2D) transition metal dichalcogenides nanosheets and three-dimensional (3D) carbon framework composites (2D/3D ReS 2 @C) as a photothermal material, which has an excellent broadband light absorption performance (in the wavelength range from 200 to 2500 nm). A small thermoelectric (TE) module with an area of 4 × 4 cm 2 is integrated with annealed ReS 2 @C as a light absorber for the investigation of photo-thermoelectric conversion. The open-circuit voltage of the assembled device increases clearly under solar illumination and reaches the maximum value of 136.3 mV, which is ∼ five times larger than that without the absorber. In addition, 20 TE modules coated with ReS 2 @C absorber layers are connected in series, which can produce a maximum open-circuit voltage of 2.12 V (∼66.25 V/m 2 ) to light up a red light-emitting diode (LED) under natural sunlight. Moreover, the annealed ReS 2 @C powder demonstrates a rapid and strong photothermal response under NIR light (wavelength ＞800 nm), which indicates a great application potential in photothermal imaging and photothermal cancer therapy.
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）