JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2021
·Vol. 32
·期 5
·5821-5830
·
IF 2.478
Hu Peng,Deng Zhaoping,Wang Teshen,Li Zepeng,Ma Yanlin
In this study, a series of Eu 3+ -doped NaBaBi 2 (PO 4 ) 3 red phosphors were synthesized by high-temperature solid-phase reaction method, and the phase structure and photoluminescence properties of the samples were investigated in detail. All the diffraction peaks of the phosphors with various Eu 3+ concentrations are well matched with the NaBaBi 2 (PO 4 ) 3 standard phase, indicating that Eu 3+ ions have no effect on the host structure. Under the excitation of 391 nm wavelength, the emission spectra consisted of four characteristic emission peaks at 595, 617, 656 and 703 nm, respectively. The strongest emission peaking at 617 nm originates from the 5 D 0 → 7 F 2 electron transitions of Eu 3+ ions. The optimum concentration of Eu 3+ ions in NaBaBi 2 (PO 4 ) 3 :Eu 3+ is 9% concentration. The phosphor exhibits strong absorption capacity in the near-ultraviolet region. The Commission International de I’Eclairage chromaticity coordinates of the NaBaBi 2 (PO 4 ) 3 :Eu 3+ samples are located in the red region, indicating that the phosphors are suitable red component to applied in near-ultraviolet-based white light-emitting diodes.
✓ 已验证
DOI
高影响因子
ACS Sustainable Chemistry & Engineering
·
2022
·
IF 9.224
Zixin Zhong,Haolan Liu,Ruru Zhou,Boyong Ye,Jie Fu,Zhaoyin Hou
3-Hydroxybutyric acid (3-HBA) is an important monomer for manufacturing biodegradable polymers such as polyhydroxyalkanoates, which are currently produced via an expensive and time-consuming microbial fermentation route. Herein, the catalytic synthesis of 3-HBA via the selective oxidation of 1,3-butanediol (1,3-BDO) in the presence of molecular oxygen is reported for the first time. It was found that the PtSb2 alloy could catalyze the selective formation of 3-HBA, and the selectivity of 3-HBA was 82.3% at a 1,3-BDO conversion level of 95.5%. The calculated turnover frequency of each surface Pt atom in the PtSb2/AC catalyst was 344.3 h–1 at 70 °C. The characterization results indicated that the prominent performance of the PtSb2 alloy over monometallic Pt nanoparticles could be because the alloy could promote the tandem oxidation of the 3-hydroxybutyraldehyde (3-HBAD) intermediate to 3-HBA and reduce the dehydration of 3-HBAD to the byproduct. At the same time, the PtSb2 alloy was also effective for the selective oxidation of several diols to hydroxyl-substituted acids.
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2021
·
IF 4.527
Jinpeng Ma,Ke Zhu,Da Huo,Bingzhong Shen,Yang Liu,Xudong Qi,Enwei Sun,Rui Zhang
The performances of 1–3 piezocomposite materials under various poling conditions were compared and analysed. The dielectric , piezoelectric , and electromechanical properties of 1–3 piezocomposite materials were studied with variations in the electric field amplitude ( E p ), poling frequency ( f ), and number of cycles ( C ). It was found that the piezoelectric coefficient ( d 33 ), free dielectric constant ( ε 33 T / ε 0 ), and electromechanical coupling factor ( k t ) of 1–3 piezocomposite materials exhibit an increase of 21.4%, 13%, and 10.7%, respectively, under the optimum alternating current poling (ACP) condition ( f = 1.25 Hz, E p = 2 kV/mm, C = 16), compared with that of the samples poled using the direct current polarisation (DCP) method. The studies of the domain pattern indicate that the performance enhancement originates from the remarkable regularly striped domain structure and high domain wall density in ACP-poled samples. Our results suggest that the ACP method is effective in enhancing the performance of composite piezoelectric materials , which possess great benefits and potential for application in acoustic/medical transducers.
✓ 已验证
DOI
高影响因子
EUROPEAN JOURNAL OF INORGANIC CHEMISTRY
·
2025
·
IF 2
Yue-Ling Sun,An-Hua Gong
A new barium zincophosphite BaZn 2 (HPO 3 ) 3 is obtained via a simple hydrothermal reaction. BaZn 2 (HPO 3 ) 3 crystallizes in the P space group and exhibits a novel 3D crystal structure. It possesses a short ultraviolet cutoff edge of 205 nm, corresponding to a large experimental bandgap of 5.55 eV. BaZn 2 (HPO 3 ) 3 also has good thermal stability. This present work provides a comprehensive characterization of its crystal structure and optical properties. Additionally, first-principles calculations are employed to analyze the structure–activity relationship of BaZn 2 (HPO 3 ) 3 . Graphical BaZn 2 (HPO 3 ) 3 possesses a novel 3D anion framework, short ultraviolet cutoff edge, large bandgap, and good thermal stability.
✓ 已验证
产品关联
DOI
高影响因子
MICROCHIMICA ACTA
·
2024
·Vol. 191
·期 7
·1-11
·
IF 5.3
Zhao Zhihua,Yao Longqi,Zhang Shuaiwen,Shi Qingsheng,Rahmatullah Abu Bakker Md,Wu Lan
Industrialization and agricultural demand have both improved human life and led to environmental contamination. Especially the discharge of a lot of poisonous and harmful gases, including ammonia, ammonia pollution has become a pressing problem. High concentrations of ammonia can pose significant threats to both the environment and human health. Therefore, accurate monitoring and detection of ammonia gas are crucial. To address this challenge, we have developed an ammonia gas sensor using In(OH) 3 /Ti 3 C 2 T x nanocomposites through an in-situ electrostatic self-assembly process. This sensor was thoroughly characterized using advanced techniques like XRD, XPS, BET, and TEM. In our tests, the I/M-2 sensor exhibited remarkable performance, achieving a 16.8% response to 100 ppm NH 3 at room temperature, which is a 3.5-fold improvement over the pure Ti 3 C 2 T x MXene sensor. Moreover, it provides swift response time (20 s), high response to low NH 3 concentrations (≤ 10 ppm), and excellent long-term stability (30 days). These exceptional characteristics indicate the immense potential of our In(OH) 3 /Ti 3 C 2 T x gas sensor in ammonia detection. Graphical Abstract
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CERAMICS INTERNATIONAL
·
2024
·
IF 5.1
Shumin Duan,Zhenjun Qing,An Liu,Haiyan Li,Yan Xue
The single-phase, cubic-structured Ba 3 La(PO 4 ) 3 ceramics were synthesized using the traditional solid-state reaction method. The ceramic sintered at 1375 °C exhibited a relative density of 95.4 %, indicative of a dense microstructure and excellent sintering characteristics. Furthermore, they displayed remarkable microwave dielectric properties : ε r = 9.54, Q × f = 32820 GHz, and τ f = −43.1 ppm/°C. In addition, the relative density is positively correlated with ε r and Q × f of ceramics. According to the complex chemical bond theory, the ionicity of the Ba/La–O bond has a more significant impact on the ε r , while the lattice energy and bond energy of the P–O bond respectively dominate the Q × f and τ f values. Moreover, the results from Raman spectroscopy indicate that several prominent Raman bands are associated with the vibration of the P–O bond. These findings suggest that Ba 3 La(PO 4 ) 3 ceramics hold promise for applications in high-frequency microwave communication.
✓ 已验证
产品关联
DOI
高影响因子
IEEE SENSORS JOURNAL
·
2024
·Vol. 24
·期 13
·21276-21285
·
IF 4.3
Xinghua Shi,Anxue Zhang,Guoqing Han,Yuemeng Yin,Wenchao Chen
Highway bridges are primarily reinforced concrete structures. They have multilayer steel mesh sheets, corrugated pipes, and steel strands inside. As a result, detecting defects in bridge concrete structures requires high technical expertise and can be challenging. This article presents a new device of ground-penetrating radar (GPR) designed specifically for highway bridge inspection. It employs antenna array technology, multichannel radar control technology, and real-time 3-D data acquisition and display technology to achieve reliable detection of various concrete structures commonly found in bridges. Using a 1.3 GHz central frequency antenna array and a multichannel control unit, the system enables simultaneous surveying along five lines, the detection depth can exceed 600 mm in concrete. This significantly enhances detection efficiency. By employing specialized software processing, the detection results are presented in a specific and visually comprehensive 3-D format. Moreover, the system provides 3-D slice images from any position and direction, facilitating the interpretation of detection results for various targets, including reinforcement layout, protective layer thickness, corrugated pipes, steel strands, and other quality defects. It provides advanced and reliable technical means for construction quality control and bridge health monitoring of highway bridges. The results indicate that the device performs well not only in controlled experimental environments, but also in real-world bridge structure environments.
✓ 已验证
DOI
高影响因子
Advanced Sustainable Systems
·
2023
·Vol. 9
·期 7
·2300233
·
IF 7.1
Sijie Yu,Yuwei Chen,Yangyang Huang,Huabin Sun,Yu Xie,Sihao Du,Wei Luo
NASICON (NAtrium Super Ionic CONductor)-structured Na 4 MnCr(PO 4 ) 3 has attracted attention as a promising cathode for sodium-ion batteries due to its high operating voltage and specific capacity contributed by multielectron reactions. Unfortunately, its intrinsic low electronic conductivity significantly hinders the release of specific capacity and rate capability, preventing its practical application. Herein, a carbon layer with dual conductive networks connected by chain-like Ketjen black (KB) is built on the surface of Na 4 MnCr(PO 4 ) 3 material. This novel Na 4 MnCr(PO 4 ) 3 /C@KB composite material exhibits improved rate capability of 61.2 mAh g −1 at 2 C compared to 19.5 mAh g −1 of Na 4 MnCr(PO 4 ) 3 /C and high reversible capacity of 88.0 mAh g −1 at 1 C with 73% capacity retention after 100 cycles. The enhanced electrochemical performance can be ascribed to an increase of electronic conductivity enabled by the dual conductive 3D network construction and an adequate infiltration of electrolyte by substantial pores existence in carbon layer. A promising dual conductive network design strategy is demonstrated here for improving the performance of NASICON-structured cathodes.
✓ 已验证
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2017
·
IF 7.504
Nan Wang,Hancheng Yuan,Yanna NuLi,Jun Yang,Jiulin Wang
The development of rechargeable Mg-based batteries with a high energy density is restricted by the high-voltage cathodes and the parasitic side reactions between the battery components and electrolytes operating at relatively high potentials. Here, we develop a hybrid Mg2+/Li+ cell using a monoclinic or orthorhombic Fe2(MoO4)3 cathode, a Mg anode, and a simple (PhMgCl)2–AlCl3 + LiCl electrolyte. Hastelloy-C alloy is proposed as a current collector of high-voltage cathode for the hybrid Mg2+/Li+ battery within a Swagelok-type cell. The application of the Hastelloy-C alloy current collector breaks the crucial bottleneck of incompatibility between the currently available current collectors and electrolytes. The hybrid cell features a low voltage polarization between the discharge and charge profiles, which is in favor of practical applications. On the other hand, because all Li+ ions are supplied by the electrolyte in a hybrid Mg2+/Li+ battery, a high Li+ concentration is required to operate at high capacities for the hybrid battery. We further show the first-hand evidence about the compensation of Li+ ions by simply soaking the cathode in the hybrid electrolyte. The prelithiation of Li+ ions into monoclinic Fe2(MoO4)3 significantly enhances the cycling stability and reversibility.
✓ 已验证
DOI
高影响因子
JOURNAL OF CHROMATOGRAPHY A
·
2022
·
IF 4.601
You-Ping Zhang,Ling-Xiao Xiong,Ying Wang,Kuan Li,Bang-Jin Wang,Sheng-Ming Xie,Jun-Hui Zhang,Li-Ming Yuan
Polyimine macrocycles are a new class of organic macrocycles with cyclic structures, well-defined molecular cavities, and multiple cooperative binding sites, which have recently aroused considerable research interest in molecular recognition and separation. Herein, we report the bonding of a [3+3] chiral polyimine macrocycle (H 3 L, C 78 H 78 N 6 O 3 ) on thiol-functionalized silica gel using thiol-ene click chemistry to prepare a chiral stationary phase (CSP) for high performance liquid chromatography (HPLC). The fabricated column exhibited excellent chiral separation capability under both normal-phase and reversed-phase conditions. Fourteen and 10 racemates were well resolved on the column in normal-phase mode (using n -hexane/isopropanol as the mobile phase) and reversed-phase mode (using methanol/water as the mobile phase), respectively, including alcohols, esters, ethers, ketones, aldehydes, epoxides and organic acids. Moreover, the column also shows good selectivity toward positional isomers. Six positional isomers (dinitrobenzene, chloroaniline, bromoaniline, iodoaniline, nitrobrobenzene and nitrochlorobenzene) were well separated on the column. In addition, the effects of the injection mass and mobile phase composition on the separation were investigated. The column shows good reproducibility and stability after multiple injections with the relative standard deviation (RSD) ( n = 5) of the retention time and resolution being < 0.96 % and 0.65 %, respectively. This study indicates that this type of chiral polyimine macrocycles is a promising chiral selector for HPLC enantioseparation and will push forward the applications of more novel chiral macrocycles for chiral chromatographic separation.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
EUROPEAN JOURNAL OF PHARMACOLOGY
·
2019
·
IF 3.17
Qi-meng Liu,Qing Xiao,Xiang Zhu,Kai-feng Chen,Xia-wen Liu,Ru-chao Jiang,Dan Wu,Jun-min Shi,Li-jun Dai,Jun-jun Huang
Benign prostatic hyperplasia (BPH) is a common disorder of the urinary system in aging men. 2-(1H-indol-3-yl)-N-[3-(4-(2-methoxyphenyl) piperazinyl) propyl] acetamide (HJZ-3), which is derived from naftopidil , exhibited 97.7- and 64.6-fold greater inhibitory effects for a 1D adrenoceptor than for a 1B - and a 1A -adrenoceptors in vitro, respectively. To investigate the therapeutic potential for treating BPH, we evaluated the pharmacological activity of HJZ-3. Specifically, we evaluated through estrogen/androgen-induced rat benign prostatic hyperplasia model in vivo. HJZ-3 effectively prevented the progression of rat prostatic hyperplasia by suppressing the increase in prostate index and reducing the quantitative analysis of the relative acinus volume, relative stroma, epithelial volume and epithelial thickness and expression of proliferating cell nuclear antigen and α -smooth muscle actin. HJZ-3 decreased α 1A - and α 1D -adrenoceptor protein expressions in prostate tissue. HJZ-3 is a good alternative for α 1A - and α 1D -adrenoceptor blocker. It may relax smooth muscle tone and relieve symptoms of BPH.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ChemPlusChem
·
2020
·Vol. 85
·期 1
·240-246
·
IF 2.753
Sheng Tang,Xinyu Xiao,Jing Hu,Bo Gao,Hunglin Chen,Zongyang Peng,Jianchun Wen,Masanao Era,Dechun Zou
Graphical Solvent-free is best : Mixed halide hybrid perovskites (MHPs) are prepared through a solvent-free mechanochemical synthesis (MCS) route with superior control over halide compositions. The MCS route eliminates the problem in the preparation of MAPb(I x Br 1− x ) 3 with continuously varying x , while maintaining the material properties and suppressing phase segregation in solvent synthesis (SS) routes. Thus, the optical band gaps can be tuned easily by compositional control. Hybrid perovskites have recently received much attention in optoelectronic applications. However, hybrid perovskites are unstable in a humid environment. Mixed halide perovskites (MHPs) show enhanced stability and band-gap tunability upon engineering of their halide composition. Here, MHPs are prepared through a solvent-free mechanochemical synthesis (MCS) route that allows superior control over halide compositions than the solvent synthesis routes (SS). The MCS route eliminates the problem in the preparation of MAPb(I x Br 1− x ) 3 with continuously varying x , while maintaining the material properties and suppressing phase segregation present in SS routes. UV-vis absorption and X-ray diffraction patterns confirm the production of the desired pure-phase MHPs. For MAPb(I x Br 1− x ) 3 (0≤ x ≤1), with increased ratio of halide ( x ), the cubic phase gradually transforms into the tetragonal phase and band-gap tunability is accomplished. The MCS route for the preparation of MHPs is a very promising and efficient technique for superior control in optoelectronic properties, leading to improved control in fabrication approaches.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）