CERAMICS INTERNATIONAL
·
2021
·
IF 4.527
Ting Chen,Dongyu Wang,Xianfu Chen,Minghui Qiu,Yiqun Fan
In this study, a novel method was proposed for preparing high-flux ceramic membranes via digital light processing (DLP) three-dimensional (3D) printing technology. Two different alumina powders were well dispersed in a photosensitive resin to form a UV-curable slurry for DLP 3D printing. The effects of the grading ratio on the viscosity of the slurry and the porosity, pore size distribution , mechanical strength , roughness, and permeability of the ceramic membranes were systematically investigated. The thermal treatment conditions were also studied and optimized. The obtained ceramic membranes exhibited a uniform pore size distribution, a high porosity, a low tortuosity factor, and an asymmetric structure. The combination of these factors led to a high flux for the 3D-printed ceramic membranes. DLP 3D printing exhibited a good potential to be a strong candidate for the next generation of ceramic membrane fabrication technology.
✓ 已验证
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2020
·
IF 6.182
Min Li,Xian Wei,Shiliang Mei,Zhongjie Cui,Yizhou Fan,Bobo Yang,Zhuoqi Wen,Zhiyong Xiong,Le Wang,Fengxian Xie,Wanlu Zhang,Ruiqian Guo
Single-phased and white-emissive quantum dots (QDs) with a broadband spectrum are highly desirable as color converter for white light-emitting diodes (WLEDs) and have been less researched up till now. In this work, a series of copper gallium selenium based multicomponent QDs including quaternary Cu-Zn-Ga-Se (CZGSe) and quinary Cu-Mn-Zn-Ga-Se (CMZGSe) QDs were synthesized. From the perspective of thermodynamics and kinetics, the comparison between PL spectra under increasing temperatures via one-pot and hot-injection methods indicated that the formation of CZGSe cores originated from the diffusion of Cu + into Zn-Ga-Se nanoparticles . For wider spectra distribution, the incorporation of Mn 2+ gave rise to Mn d-d emission around 590 nm. Together with Cu-related emission about 500 nm and intrinsic emission around 430 nm, white emission of CMZGSe QDs could be realized well-tuned by incremental ZnSe deposition, whose chromaticity coordinates shifted along with the Planckian locus. These results about multicomponent alloyed QDs enrich mechanistic insight for the formation kinetics and reveal the potential to fabricate better color rendering WLEDs .
✓ 已验证
DOI
高影响因子
DIAMOND AND RELATED MATERIALS
·
2021
·
IF 3.315
Yanhua Gao,Wenli Zhao,Dongfeng Zhang
In this paper, the growth mechanism of prismatic carbon nitride at different temperatures was studied by using the mixed solution of CTAB and NaOH by thermal polycondensation-hydrothermal method, and a series of characterization methods were used to analyze and verify. The pollutant model MO solution was degraded and its photocatalytic activity was investigated under light. The results show that at a relatively low temperature, g-C 3 N 4 is a rod-like structure, and NaOH plays a major role. With the increase of temperature, CTAB plays a major role and can transport the primitives to form a rod, but also forms an ordered hydrophobic film on the crystal plane, which inhibits the growth of the rod-like structure on the (100) crystal plane and controls the extension on the (002) crystal plane. Its degradation rate is about 2.64 times that of pure g-C 3 N 4 . This significantly improves the separation rate of photogenerated electrons and the photocatalytic degradation efficiency.
✓ 已验证
DOI
高影响因子
Journal of Central South University
·
2023
·Vol. 30
·期 8
·2501-2509
·
IF 4.4
Liu Wen-bo,Du Xue-rong,Wang Cheng-cheng,Zhuo Chun-xue,Chang Jin,Wang Na-na,Li Ren-zhi
Cesium copper halides have attracted increasing attention for light-emitting diodes (LEDs) applications due to their high photoluminescence quantum efficiency (PLQE) and non-toxicity. However, the current film fabrication methods for copper halides cannot simultaneously meet the high-performance, eco-friendly, and good environmental tolerance requirements. Here, we demonstrate a facile approach that combines the advantages of both traditional nanocrystal-based methods and precursor solution-based methods. Through treating Cs 3 Cu 2 I 5 nanocrystal films with proper alcohols, Cs 3 Cu 2 I 5 /CsCu 2 I 3 mixed-dimensional copper halides are formed with enhanced PLQE and improved energy level matching. This enhances the peak EQE of copper halide LEDs to 0.8%, which is among the highest efficiency of lead-free metal halide nanocrystal LEDs. This work provides a new strategy for fabricating high-performance lead-free LEDs in an eco-friendly manner.
✓ 已验证
DOI
高影响因子
MACROMOLECULAR RAPID COMMUNICATIONS
·
2019
·Vol. 40
·期 22
·1900441
·
IF 4.078
Hanzhi Zhang,Tongtong Zhou,Jiwei Shen,Ping Zhang,Xin Chen,Yongming Chen,You Yu
Finely tuning the photodegradation behavior of the layer-by-layer (LbL) film from the view of controlling the chemical structure of the film-building polymer is still a challenge in related fields. To meet this requirement, a photodegradable polymer (P1) is rationally designed for assembling a visible-light-degradable multilayer film with polystyrene sulfonate (PSS). Compared with similar photopolymers (P2 and P3), this asymmetric picolinium-containing polymer can significantly enhance the degradation rate of as-prepared LbL films; under the same degradation condition, the degradation rate of (P1/PSS)10 is 3 and 6.6 times that of (P2/PSS)10 and (P3/PSS)10, respectively. Moreover, near-infrared light (NIR) is available for triggering the degradation of this film with the assistance of upconversion nanoparticles of YbTm@Lu. The cell cytotoxicity and cell proliferation experiments reveal that P1 is nontoxic and favorable for cell proliferation at concentrations of up to 500 μg mL −1 . As for (PSS/P1)10 films, the ratio of cell number of these two samples ((PSS/P1)10 modified: photodegraded) increases dramatically and reaches about 1.67:1 after 72 h incubation. On the basis of these results, it is anticipated that P1 and this LbL film is an exceptional candidate for visible-light/NIR degradable materials in materials and biological science, medicine, and optics.
✓ 已验证
DOI
高影响因子
Desalination and Water Treatment
·
2024
·
IF 1
Huiya Wang,Keqiang Ding,Danping Shao,Guoqiang Pan
In this study, water-soluble graphitic carbon nitride nanosheets (WS-CNNS) were successfully prepared by using the KOH/NaOH melt, and the synthesized WS-CNNS could be applied to the environmental treatment. The photocatalytic degradation experimental results showed that the WS-CNNS has great photocatalytic activity for photocatalytic degradation of Methylene blue (MB). Moreover, the capture experiments shown that H 2 O 2 played an important role in the photocatalytic degradation of MB. The superior photocatalytic performance of WS-CNNS was mainly ascribed to the characteristics of water solubility together with optical properties. This research provides a new perspective for the application of graphitic carbon nitride nanosheets in environmental remediation.
✓ 已验证
DOI
高影响因子
APPLIED CATALYSIS B-ENVIRONMENTAL
·
2020
·
IF 16.683
Guoqiang Zhang,Yangsen Xu,Chuanxin He,Peixin Zhang,Hongwei Mi
Crystalline carbon nitride (CCN) materials with photoresponse of more than 600 nm are rare. Here, we successfully prepared a series of oxygen doped K + implanted CCN (KCN) with narrowed bandgap (2.71−1.62 eV) for the first time. Compared with most of the O-doped amorphous CN, the optical absorption can only reach 500 nm, and a few more than 500 nm, our oxygen doping strategy is adopted to activate more n→π* transitions to enhance visible light and even near-infrared light harvesting. This active-optimized O-doped KCN accounts for 45- and 10- times promotion than pristine CN and KCN in H 2 generation under λ > 500 nm. Most importantly, its maximum active wavelength is up to 650 nm, which has obvious advantages than most CCN-based photocatalysts in the utilization of solar energy. This excellent solar capture and H 2 production is attributed to the activated n→π* electron transition, and high crystallinity and conduction band (CB) position caused by oxygen doping.
✓ 已验证
DOI
高影响因子
AIP Advances
·
2023
·Vol. 13
·期 6
·
IF 1.6
Tu Peng,Cai Xiangcheng,Ai Yansong,He Hongshen,Shen Peng,Zhou Yuanming,Mei Fei
Perovskite light-emitting diodes (PeLEDs) have attracted much attention due to their excellent performance. In this work, phenylethylamine bromide (PEABr) was employed to modify perovskite phases, while Poly(9-vinylcarbazole) (PVK) was added as a hole transport layer between perovskite and PEDOT:PSS to engineer the device structure, which is predicted to improve the optoelectronic performance of PeLEDs synergistically. The doping of PEABr in MAPbBr 3 can improve the radiative recombination of the emission layer through the formation of two-dimensional perovskite phases and modified film morphology. When the ratio of MAPbBr 3 :PEABr is 1:0.25, the maximum luminance of the optimal device increased from 80 to 9000 cd/m 2 and the maximum external quantum efficiency increased from 0.02% to 1.63% compared with the control device without PEABr doping. In addition, the hole injection ability of the device is further improved by adding PVK as the hole transport layer. The introduction of PVK can also facilitate the interface modification via surface defect passivation. When the PVK concentration is 10 mg/ml, the maximum current efficiency and external quantum efficiency of the optimal device are increased to 13.70 cd/A and 2.70%, respectively. These findings can provide a basis for the enhanced performance of PeLEDs.
✓ 已验证
DOI
高影响因子
SYNTHETIC METALS
·
2021
·
IF 3.266
Bingli Gu,Zhiduo Liu,Da Chen,Bo Gao,Yongsheng Yang,Qinglei Guo,Gang Wang
Light-emitting graphene quantum dots (GQDs) are widely investigated due to their distinct merits. However, GQDs generally suffer from aggregation-induced luminescence quenching, which means they are highly emissive in a solution state with uniform dispersion but dramatically quenched in a solid or aggregated state. This problem significantly limits the application of GQDs, partially in the solid-state light-emitting devices. In this report, we successfully developed a simple and efficient hydrothermal method for the production of nitrogen doped graphene quantum dots (N-GQDs) with strong solid-state fluorescence (SSF) by using citric acid and o-Phenylenediamine as precursors. Under the 365 nm UV light illumination, the produced N-GQDs in an aqueous state exhibit blue color, with a quantum yield of 58%. As the concentration of N-GQDs increases, the photoluminescence exhibits an obvious red-shift from blue to yellow. For the N-GQDs in solid state, yellow luminescence with a high photoluminescence quantum yield (PLQY) of 28% is achieved under the 405 nm excitation. Finally, via the simple adjustment of thickness and the concentration of N-GQDs in blue emitting InGaN chips, color converter is enabled by constructing white light-emitting diode (WLED) device with improved color rendering index (CRI) and correlated color temperature (CCT).
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2019
·
IF 8.355
Kun Zheng,Xu Li,Mingjun Chen,Yi Gong,Aiwei Tang,Zhenguang Wang,Zhiren Wei,Li Guan,Feng Teng
According to mastery of solvent and reaction temperature, red, yellow, and blue emissive carbon nanodots (CNDs) with high quantum yield are successfully achieved using neutral red carbon source by solvothermal methods. The differences on the emission color of CNDs are evidently ascribed to conjugated absorption bands from n-π* transition confirmed by structural and optical characterizations. The results of quantum yield, transmission electron microscopy images, high magnification fluorescent micrographs of CNDs ethanol solution and solid-state CNDs & polyvinylpyrrolidone (CNDs&PVP) powders reveal that the obtained CNDs possess ultrahigh luminescence, favorable solubility, uniform dispersibility and well material compatibility. The bright fluorescent films were fabricated by mixing the CNDs &PVP composite powders with the epoxy. By taking advantage of these remarkable properties, the red, yellow, blue light-emitting diode was realized by combining CNDs&PVP film with a UV-LED chip. This work provides a new perspective for the explanation of the PL mechanism and the exploration of stable, high-performance, and environment-friendly multicolored CNDs-based LEDs.
✓ 已验证
DOI
高影响因子
JOURNAL OF HAZARDOUS MATERIALS
·
2014
·
IF 4.331
Chengqun Xu,Honghai Wu,Feng Long Gu
BiOBr/Na–montmorillonite composites (BiOBr–Mt) were prepared under laboratory ambient conditions by using the surfactant cetyltrimethylammonium bromide (CTAB) as the Br source and template, and the as-synthesized samples were characterized by XRD, FT-IR, FESEM, TEM equipped with EDS, BET and UV–vis DRS techniques. Interestingly, the particle size of BiOBr can be controlled by CTAB modified Na-montmorillonite. The photocatalytic activity of the as-prepared was further evaluated by decomposition of Rhodamine B (RhB) under visible light irradiation; the obtained results revealed that the BiOBr–Mt sample had strong photoabsorption in the visible light region. It has higher photocatalytic activity than pure BiOBr alone. There exists an efficient adsorption for RhB onto BiOBr–Mt contrast to that onto the pure BiOBr. The adsorption processes can be well described by pseudo-second-order kinetic model; meanwhile, the adsorption behaviors can be described by both Freundlich and Langmuir equations but the former was better. Additionally, the relevant adsorption and degradation mechanisms were explored and the possible mechanisms were presented. The photocatalytic activity has high effect both in acidic and basic conditions on the degradation reaction but in acidic condition is more favorable. After three recycles, BiOBr–Mt did not exhibit any significant loss of photocatalytic activity, confirming the photocatalyst was essentially stable.
✓ 已验证
DOI
高影响因子
Desalination and Water Treatment
·
2024
·
IF 1
Zijun Zhong,Ruopeng Xu,Huijuan He,Qiuna Zhuang,Langhuan Huang
ABSTRACT A novel g-C 3 N 4 /MoS 2 heterojunction photocatalyst with high efficient visible-light-region was fabricated by a facile calcination method. The composite with various weight ratios of g-C 3 N 4 and MoS 2 was synthesized and characterized. The results showed that MoS 2 was uniformly distributed on the surface of g-C 3 N 4 , resulting in the formation of heterostructure. The photocatalyst showed excellent photocatalytic activity in the photodegradation of organic pollutants. The optimized g-C 3 N 4 /MoS 2 sample (10-CNM) exhibited 94% (Methylene Blue) degradation efficiency after being irradiated for 2 h under visible light. At last, the possible mechanism of the enhanced photocatalytic activity was discussed.
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）