文献检索

查找使用阿拉丁产品的科研文献

检索与阿拉丁产品相关的同行评审论文、DOI、PubMed 编号、期刊、作者、CAS 号及研究领域。

科研影响力快照

与阿拉丁产品相关的已发表科研成果

在搜索之前,这些指标可帮助访客快速了解产品关联科研的规模与质量。

347,389+ SCI 论文 与阿拉丁产品引用相关
2,303,681.05 总影响因子 匹配文献记录中影响因子的总和
81.20 最高期刊影响因子 匹配期刊中的最高 IF
6.63 平均期刊影响因子 匹配文献的平均 IF

参考指标 指标基于阿拉丁文献引用数据库及期刊影响因子记录。文献关联仅供科研参考,请以原始文献为准。

产品列表

视图 列表 网格

显示第3697至3708个,产品总数4,488个

切换升序
Cu
ELECTROCHIMICA ACTA · 2014 · IF 4.086

Electrochemical mechanism of eugenol at a Cu doped gold nanoparticles modified glassy carbon electrode and its analytical application in food samples

Xiaoyun Lin,Yongnian Ni,Serge Kokot

A simple one-step electrodeposition method was used to construct a glassy carbon electrode (GCE), which has been modified with Cu doped gold nanoparticles (GNPs), i.e. a Cu@AuNPs/GCE. This electrode was characterized with the use of scanning electron microscopy (SEM) and X-ray diffraction (XRD) techniques. The eugenol was electrocatalytically oxidized at the Cu@AuNPs/GCE. At this electrode, in comparison with the behavior at the GCE alone, the corresponding oxidation peak current was enhanced and the shift of the oxidation potentials to lower values was observed. Electrochemical behavior of eugenol at the Cu@AuNPs/GCE was investigated with the use of the cyclic voltammetry (CV) technique, and additionally, in order to confirm the electrochemical reaction mechanism for o-methoxy phenols, CVs for catechol, guaiacol and vanillin were investigated consecutively. Based on this work, an electrochemical reaction mechanism for o-methoxy phenols was suggested, and in addition, the above Cu@AuNPs/GCE was successfully employed for the analysis of eugenol in food samples.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CHEMICAL ENGINEERING JOURNAL · 2014 · IF 4.058

Simultaneous adsorption of Cu(II) and SO42− ions by a novel silica gel functionalized with a ditopic zwitterionic Schiff base ligand

Qiang Wang,Wei Gao,Yang Liu,Jiwen Yuan,Zhijun Xu,Qingfu Zeng,Yuguang Li,Martin Schröder

A novel silica gel based absorbent SG-H 2 L 1 , capable of simultaneous adsorption of cations and anions from aqueous solution, was prepared by immobilization of a ditopic zwitterionic Schiff base ligand H 2 L 1 onto a modified silica gel. The functionalized silica gels were characterized by Fourier transform infrared spectroscopy , elemental analysis, thermogravimetric analysis and porous structure analysis. The results showed a degree of functionalization of 0.32   mmol H 2 L 1 per gram of SG-H 2 L 1 . The effect of pH, contact time and initial Cu(II) and SO 4 2− concentration parameters on the simultaneous adsorption of Cu(II) and SO 4 2− ions were investigated. The adsorption was fast and the effective pH range for simultaneous adsorption of Cu(II) and SO 4 2− was neutral region. The adsorption study showed that SG-H 2 L 1 had good adsorption efficiency for Cu(II) and SO 4 2− , and the maximum adsorption capacity for Cu(II) and SO 4 2− , respectively, was the same of 0.65   mmol   g −1 at 25   °C. Langmuir and Freundlich isotherm models were employed to analyze the experimental data, and the Langmuir model fitted better for both Cu(II) and SO 4 2− . Due to the zwitterionic feature, desorption and regeneration of the absorbent was readily realized by adjusting the pH of the regenerating media with diluted H 2 SO 4 (0.5   mol   L −1 ) and ammonia solution (pH   =   10), respectively. The new type absorbent SG-H 2 L 1 exhibited good recyclability and reusability for 5 cycles use without deterioration in its functionality. Therefore, the adsorbent can be used effectively for efficient and simultaneous adsorption of Cu(II) and SO 4 2− from waste water. The mechanism for simultaneous adsorption of cation and anions on SG-H 2 L 1 was also discussed. This study provides a strategy for the development of new absorbents for simultaneous adsorption of hazardous metal ions and anions from waste water effluents .

CAS / MDL: 2530-87-2
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CHEMISTRY OF MATERIALS · 2013 · IF 8.238

Spinel Indium Sulfide Precursor for the Phase-Selective Synthesis of Cu–In–S Nanocrystals with Zinc-Blende, Wurtzite, and Spinel Structures

Shuijin Lei,Chunying Wang,Lei Liu,Donghai Guo,Chuanning Wang,Qingliu Tang,Baochang Cheng,Yanhe Xiao,Lang Zhou

Group I–III–VI ternary chalcogenides have attracted extensive attention as important functional semiconductors. Among them, Cu–In–S compounds have seen strong research interest due to their potential applications in high-efficiency solar cells. However, the controllable synthesis of Cu–In–S nanostructures with different phases is always difficult. In this research, zinc-blende CuInS2, wurtzite CuInS2, and spinel CuIn5S8 could be selectively synthesized using spinel In3–xS4 as the precursor by a simple solvothermal method. X-ray powder diffraction was used to determine the phase and crystal structure, and transmission electron microscopy was employed to characterize the morphologies of the as-prepared samples. Experiments showed that the acidity–basicity of the reaction system and the coordination and reducibility of the capping ligands were crucial to the final phases of the products. The UV–vis–NIR spectra of the three phases all exhibited a broad-band absorption over the entire visible light and extending into the near-infrared region, and the zinc-blende, wurtzite, and spinel Cu–In–S nanocrystals showed band gaps of 1.55, 1.54, and 1.51 eV, respectively, which indicates their potential applications in thin-film solar cells.

CAS / MDL: 112-90-3
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
REACTIVE & FUNCTIONAL POLYMERS · 2013 · IF 2.505

Temperature-tunable catalytic property of Pd–M (Ag, Cu) bimetallic nanoparticles stabilized by thermal-sensitive PDEAm-g-PAN/PSt polymeric microspheres

Shi Dongjian,Sui Jing,Duan Fang,Chen Mingqing,He Bingxiao

Thermal-sensitive poly( N , N -diethylacrylamide) grafted poly(acrylonitrile/styrene) (PDEAm- g -PAN/PSt) polymeric microspheres were prepared from PDEAm macromonomer, St and AN by dispersion copolymerization . The polymeric microspheres had raspberry-like morphology with large surface area. Palladium–metal (Pd–M) (M: copper, Cu, silver , Ag) bimetallic nanoparticles were stabilized on the surface of the PDEAm- g -PAN/PSt microspheres via the coordinate interaction between amide groups in PDEAm and metal ions with the reduction of the corresponding ions. Transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and thermogravimetry analysis (TGA) results confirmed the size and composition of the immobilized Pd–M nanoparticles. The Pd–M bimetallic nanoparticles showed superior catalytic efficiencies for the reduction of 4-nitrophenol (4-NP) than the monometallic nanoparticles. The catalytic activity of the Pd–M bimetallic catalysts could be controlled by the molar ratio of Pd and M ions and composition of Pd–M nanoparticles. Moreover, the catalytic property of the Pd–M nanoparticles could be regulated by temperature and increased with increasing the temperature above lower critical solution temperature (LCST). Furthermore, the Pd–M nanoparticles could be easily recycled and reused to catalyze 4-NP for five times without loss of activity. These bimetallic nanoparticles possess great potential in future practical application in catalytic technology.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Nanoscale · 2017 ·Vol. 9 ·期 29 ·10335-10343 · IF 7.367

Analogous self-assembly and crystallization: a chloride-directed orientated self-assembly of Cu nanoclusters and subsequent growth of Cu2−xS nanocrystals

Jiale Liu,Ye Tian,Zhennan Wu,Lin Ai,Yi Liu,Jianli Cui,Weili Yu,Hao Zhang,Bai Yang

Self-assembly and crystallization are two common methods to control the morphologies of nanomaterials, which have many similarities. In this work, chloride is used to direct the self-assembly process of Cu nanoclusters and the subsequent growth of Cu2−xS nanocrystals. Meaningfully, chloride both promotes the transformation of Cu nanocluster self-assembled architectures from one-dimensional (1D) to 2D, and facilitates the transformation of Cu2−xS nanocrystals from nanorods to nanosheets. Such an influence is attributed to the selective adsorption of chloride ions on the specific facets of nanoclusters and nanocrystals, which alters the inter-nanocluster weak interactions during self-assembly and suppresses the activity of Cu2−xS facets during nanocrystal growth. The current results indicate that the method used to direct the morphologies of nanocrystals is extendable to control the tendency of nanocluster self-assembly.

CAS / MDL: 112-55-0
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
ECOTOXICOLOGY AND ENVIRONMENTAL SAFETY · 2017 · IF 3.743

Encapsulating Fe3O4 into calcium alginate coated chitosan hydrochloride hydrogel beads for removal of Cu (II) and U (VI) from aqueous solutions

Xiaofeng Yi,Jiarui He,Yingyuan Guo,Zhenhua Han,Meixia Yang,Jiali Jin,Junjie Gu,Minrui Ou,Xiaoping Xu

The aim of this work was to study the removal of Cu (II) and U (VI) ions from aqueous solutions by encapsulating magnetic Fe 3 O 4 nanoparticles into calcium alginate coated chitosan hydrochloride (CCM) hydrogel beads. ATR-FTIR and XRD analysis data indicated that the CCM composites were successfully prepared. SEM images and EDX spectra showed that Cu 2+ and UO 2 2+ ions were adhered onto sorbents . Adsorption properties for removal of both copper and uranium ions under various experimental conditions were investigated. Kinetic data and sorption equilibrium isotherms were also conducted in batch process . The sorption kinetic analysis revealed that sorption of Cu (II) and U (VI) followed the pseudo-second-order model well and exhibited 3-stage intraparticle diffusion model during the whole sorption process. Equilibrium data were best described by Langmuir model, and the CCM composite hydrogel beads showed the estimated maximum adsorption capacity 143.276   mg/g and 392.692   mg/g for Cu (II) and U (VI), respectively. The CCM adsorbent exhibited excellent reusability for five cycles use without significant changes in the adsorption capacity and structural stability. The results demonstrated that CCM can be an effective and promising sorbent for Cu (II) and U (VI) ions in wastewater.

CAS / MDL: 1317-61-9
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
JOURNAL OF ELECTROANALYTICAL CHEMISTRY · 2017 · IF 3.012

Utilization of AuNPs dotted S-doped carbon nanoflakes as electrochemical sensing platform for simultaneous determination of Cu (II) and Hg (II)

Yinxiu Zuo,Jingkun Xu,Fengxing Jiang,Xuemin Duan,Limin Lu,Guo Ye,Changcun Li,Yongfang Yu

Gold nanoparticles (AuNPs) dotted S-doped carbon (AuNPs/S-C) nanoflakes were synthesized via a facial and simple approach. Typical synthesis route involves the formation of gold nanoparticles/poly(3,4-ethylenedioxythiophene) (AuNPs/PEDOT) and a subsequent calcination process. Many techniques, including scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS) were used to characterize their morphology, structures and compositions . Results indicated that AuNPs with an average size of 5   nm were uniformly dotted on/into the S-C nanoflakes. The AuNPs/S-C/nafion was utilized as a new electrode material for simultaneously electrochemical determination of Cu (II) and Hg (II) using differential pulse anodic stripping voltammetry (DPASV) technique. Benefiting from the efficient metal-complexing ability and electrocatalytic activity of S-C and the good conductivity of AuNPs, the modified electrode exhibited enhanced electrochemical performance compared with bare glassy carbon electrode. Under optimal conditions, the peak currents displayed linear response to the concentrations of Cu (II) and Hg (II) ranges from 0.64 to 63.55   μg/L and 4.01 to 300.89   μg/L, with detection limits of 0.19   μg/L and 1.40   μg/L (S/N   =   3), respectively. The modified electrode was also applied for the determination of Cu (II) and Hg (II) in lake water samples with good results.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
HYDROMETALLURGY · 2017 · IF 2.605

Synthesis of Cu(II) ion-imprinted polymers as solid phase adsorbents for deep removal of copper from concentrated zinc sulfate solution

Tianlin Zhang,Xiadan Yue,Keren Zhang,Fei Zhao,Yulu Wang,Kun Zhang

Novel copper (II) ion imprinted polymers (Cu(II)-IIPs) were designed and synthesized as solid phase absorbents for the selective deep removal of Cu 2   + from concentrated zinc sulfate solution. Salicylaldoximes, used as chelating ligands, were anchored onto the polymer networks through quaternary ammonium cation spacers. The effect of pH, temperature, contact time, and swelling on the adsorption selectivity and the copper removal efficiency of Cu(II)-IIPs were investigated in a laboratory-scale cell. The results showed that the adsorption of Cu 2   + increased significantly with increasing pH from 1 to 7, and increased with decreasing operation temperature. The equilibrium Cu 2   + adsorption capacity of Cu(II)-IIPs from the zinc sulfate aqueous solution was 96   mg·g −   1 at 25   °C in pH   5.0 for 10   min. Under optimized processing conditions, the copper removal efficiency reached 99.9%, and the concentration of the residual copper (II) ions in the purified ZnSO 4 aqueous solution is 35   μg·L −   1 , significant lower than the maximum acceptable value as 100   μg·L −   1 in the hydrometallurgical zinc process.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
APPLIED CLAY SCIENCE · 2016 · IF 2.586

Immobilization of visible light-sensitive (N, Cu) co-doped TiO2 onto rectorite for photocatalytic degradation of p-chlorophenol in aqueous solution

Zhujian Huang,Pingxiao Wu,Beini Gong,Xing Zhang,Zicong Liao,Pen-Chi Chiang,Xinjiang Hu,Lihua Cui

To further enhance the photocatalytic properties of doped-TiO 2 , a series of (N, Cu) co-doped TiO 2 /rectorite composites with different amount of N doping were prepared for adsorption and catalytic oxidation of p -chlorophenol ( p -CP) under visible light. The physicochemical properties of the obtained composites were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), etc. The results showed that the (N, Cu) co-doped TiO 2 catalyst was immobilized well onto rectorite , and the doping of N and Cu could affect the crystal structure of TiO 2 . The optimal N doping amount was determined by the photocatalytic degradation of p -CP in a stirred quartz reactor under visible light (>   420   nm) irradiation. It was found that the doping of N can improve significantly the degradation of p -CP and the optimum N doping amount is 1.0%. The adsorption of p -CP by the composites could accelerate the degradation rate of p -CP in situ. The photocatalytic activity of the (N, Cu) co-doped TiO 2 /rectorite composites remained stable after five cycles of photoreaction. A possible mechanism for the photocatalytic degradation of p -CP is proposed. Our work implied that rectorite has great potential to be applied in the field of photocatalysis .

CAS / MDL: 106-48-9
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
SENSORS AND ACTUATORS B-CHEMICAL · 2016 · IF 4.758

Flexible paper sensor fabricated via in situ growth of Cu nanoflower on RGO sheets towards amperometrically non-enzymatic detection of glucose

Bin Wang,Yuanya Wu,Yanfen Chen,Bo Weng,Changming Li

A flexible free-standing paper sensor was fabricated for the first time via in situ growth of Cu nanoflower on reduced graphene oxide (RGO) sheets towards amperometrically non-enzymatic detection of glucose. The low cost of copper (Cu) and graphene made the prepared sensor inexpensive in comparison with sensors made from noble metal catalysts . This Cu-RGO paper sensor exhibited high sensitivity and good selectivity when utilised in glucose sensing attributed to the synergistic effects of graphene paper and Cu nanoflowers. The combination of excellent catalytic activity , largely reactive surface area of Cu nanoflower and good conductivity of graphene paper enabled the sensor to perform well in glucose detection. The prepared glucose sensor holds a great promise for inexpensive flexible electrochemical non-enzymatic glucose sensors.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
ACS Applied Materials & Interfaces · 2016 · IF 7.145

One-Pot Fabrication of Hollow and Porous Pd–Cu Alloy Nanospheres and Their Remarkably Improved Catalytic Performance for Hexavalent Chromium Reduction

Shu-He Han,Juan Bai,Hui-Min Liu,Jing-Hui Zeng,Jia-Xing Jiang,Yu Chen,Jong-Min Lee

Noble metal nanostructures (NMNSs) play a crucial role in many heterogeneous catalytic reactions. Hollow and porous NMNSs possess generally prominent advantages over their solid counterparts due to their unordinary structural features. In this work, we describe a facial one-pot synthesis of hollow and porous Pd–Cu alloy nanospheres (Pd–Cu HPANSs) through a polyethylenimine (PEI)-assisted oxidation–dissolution mechanism. The strong coordination interaction between CuII and PEI facilitates the oxidation–dissolution of the Cu2O nanospheres template under air conditions, which is responsible for the generation of the Pd–Cu alloy and the convenient removal of the Cu2O nanospheres template at room temperature. Compared to the commercial Pd black, the Pd–Cu HPANSs show remarkably improved catalytic activity for the reduction of K2Cr2O7 by HCOOH at room temperature, attributing to the enhanced catalytic activity of the Pd–Cu HPANSs for the dehydrogenation decomposition of HCOOH.

CAS / MDL: 9002-98-6
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
Advanced Science · 2025 · IF 14.1

Direct Visualization and Quantitative Insights into the Formation and Phase Evolution of Cu Nanoparticles via In Situ Liquid Phase 4D-STEM

Ningyan Cheng,Hongyu Sun,Yevheniy Pivak,Christian H. Liebscher

Copper (Cu)-based nanomaterials are one of the most efficient heterogeneous electrocatalysts for the CO 2 reduction reaction. However, their selectivity and stability are strongly determined by their morphology, crystal structure, composition, grain size, grain boundary density, etc. Hence, gaining quantitative insights into their dynamic evolution under synthesis and/or working conditions is critical for developing optimal Cu-based electrocatalysts and unveiling their structure-property relationship. In this work, the possibility of addressing these issues is demonstrated by integrating in situ liquid phase transmission electron microscopy (LP-TEM) with 4D scanning transmission electron microscopy (4D-STEM). Here, the dynamic morphology and phase evolution of Cu nanoparticles during electrodeposition and electrooxidation processes are revealed in liquid. Virtual imaging and selected area electron diffraction provide novel insights into the evolution of defective nanocrystalline Cu nanoparticles during electrodeposition. It is shown that virtual off-axis dark field imaging can be used to map the distribution of Cu 2 O and Cu within partially oxidized Cu nanoparticles, opening new opportunities for quantitatively probing electrocatalysts under operando conditions.

CAS / MDL: 7758-98-7 7447-40-7
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
已复制

文献关联基于可获得的产品、CAS、DOI 及引用记录。收录不代表作者或出版方对阿拉丁产品的背书,请以原始文献为准。