JOURNAL OF SOL-GEL SCIENCE AND TECHNOLOGY
·
2019
·Vol. 91
·期 3
·514-522
·
IF 1.986
Gao Min,Liu Benxue,Zhao Ping,Yi Xibin,Shen Xiaodong,Xu Yue
Alumina (Al 2 O 3 )-based diphasic aerogels have better physical properties than those of pure Al 2 O 3 aerogel according to previous studies. In the present research, we focused on an alumina–titania (Al 2 O 3 -TiO 2 ) diphasic aerogel. A series of Al 2 O 3 aerogels were synthesized and studied with and without minor TiO 2 dopants (up to 10 mol%). We found that the pure Al 2 O 3 aerogel, which had the fiber-like particles, was stronger than those with TiO 2 dopants that possessed the sphere-like particles. However, the sphere-like particles make the TiO 2 -doped Al 2 O 3 aerogel (with 3 mol% TiO 2 ) possessing the largest specific surface area (SSA) of 650 m 2 /g, much larger than that of the pure Al 2 O 3 aerogel (326 m 2 /g). This work proved that fiber-like particles enhance strength but reduce SSA of Al 2 O 3 aerogel. At last, ceramic fibers reinforced Al 2 O 3 aerogel composites with the sizes of 20 cm width × 20 cm length × 1 cm thickness were fabricated. The aerogel composites possessed a thermal conductivity of 0.136 W/m K at 1000 °C, better than those of the ceramic fiber blankets itself (0.30 W/m K), indicating potential application as high-temperature thermal insulator.
✓ 已验证
产品关联
DOI
高影响因子
MICROCHIMICA ACTA
·
2019
·Vol. 186
·期 6
·1-9
·
IF 5.479
Lv Yuanxia,Jiang Caiyan,Hu Kun,Huang Yong,He Yunfeng,Shen Xiaoying,Zhao Shulin
Cobalt oxyhydroxide (CoOOH) was grown on the surface of graphitic-phase C 3 N 4 nanosheets to obtain an activatable fluorescent nanoprobe for ascorbic acid (AA). The probe was applied to the detection of AA in biological fluids and to image AA in HeLa cells. The negatively charged nanosheets first adsorb Co 2+ , and then the CoOOH nanoflakes are generated in-situ on the surface of g-C 3 N 4 . This results in the quenching of the blue fluorescence (with excitation/emission maxima of 345/435 nm) via fluorescence resonance energy transfer from g-C 3 N 4 to CoOOH. The AA-induced redox reaction reduces the trivalent cobalt ion in CoOOH to Co 2+ which then becomes released from the nanosheets. This leads to the recovery of fluorescence. The method can quantify AA in the 1.0 to 800 μM concentration range at near neutral pH values. When applied to cell extracts, the limit of detection is 0.14 μM. The nanoprobe was successfully applied to the determination of AA in serum and urine, and to image AA in living HeLa cells. Additional attractive features include the ease of preparation, low cytotoxicity, rapid fluorometric turn-on response, and good biocompatibility.
Schematic presentation of an activatable fluorescent nanoprobe. It consists of CoOOH nanoflakes that were modified withg-C 3 N 4 nanosheets. It enables monitoring of AA in the biological samples as well as imaging of AA in living cells.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
MICROCHIMICA ACTA
·
2019
·Vol. 186
·期 6
·1-10
·
IF 5.479
Liu Zikai,Lin Xiwen,Liu Xinya,Li Jing,Zhou Wenfeng,Gao Haixiang,Zhang Sanbing,Lu Runhua
A magnetic sorbent was fabricated by covalently grafting hyperbranched polyamidoamine onto the surface of Fe 3 O 4 nanoparticles. The sorbent was used in the magnetic solid-phase extraction (MSPE) of benzoylurea insecticides (BUs) from environmental water samples. It is perceived that hydrogen bonding interactions and hydrophobic interactions are the main mechanisms for the adsorption of BUs. The sorbent was characterized by scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, elemental analysis, Brunauer-Emmett-Teller measurement, X-ray photoelectron spectroscopy, vibrating sample magnetometry and X-ray diffraction. Various experimental parameters affecting the MSPE were optimized. Following elution with acetonitrile, the BUs were quantified by HPLC with diode array detection. The method based has a wide linear response range (2.5–500.0 ng mL −1 ), satisfactory coefficient of determination (0.9922–0.9976), high enrichment factors (62.8–74.4), acceptable limits of quantitation (2.5 ng mL −1 ) and low limits of detection (0.39–0.72 ng mL −1 ). The intra-day precision at concentration levels of 5.0, 50.0 and 250.0 ng mL −1 ranged from 2.3–6.4% and the inter-day precision was between 1.0 and 5.5%. The sorbent can be re-used at least 15 times. It was applied to the extraction of BUs from genuine water samples where it showed satisfactory relative recoveries (75.1–111.4%) and precision (1.0–9.1%).
Schematic presentation of magnetic nanoparticles modified with hyperbranched polyamidoamine and their application for extraction of benzoylurea insecticides.
✓ 已验证
DOI
PubMed
高影响因子
MICROCHIMICA ACTA
·
2019
·Vol. 186
·期 5
·1-8
·
IF 5.479
Zhao Qi,Zhou Chaohui,Yang Qingye,Chu Zhongyun,Jia Nengqin
In the Fenton reaction, ferrous ion acts as a catalyst and reacts with hydrogen peroxide (H 2 O 2 ) to produce hydroxy radicals (·OH) and hydroperoxy radicals (·OOH). Both have much stronger oxidization ability than H 2 O 2 . A fluorescent probe for H 2 O 2 is described here that was obtained by covalent conjugation of carbon quantum dots to gold nanoclusters (AuNCs). The conjugate, under 360 nm photoexcitation, displays dual (blue and red) emission, with peaks located at 450 and 640 nm. When introducing ·OH radicals via the Fenton reaction, the fluorescence intensities of both the CQDs and the AuNCs are decreased. The ratio of the fluorescence at the two peaks is related to the concentration of H 2 O 2 in the 1.25 nM to 10 μM concentration range, and the detection limit is 0.16 nM. The probe was applied to the determination of H 2 O 2 in milk and toothpaste and to cell imaging.
Schematic diagram of the FRET-based fluorescent probe and enhanced performance of hydrogen peroxide detection via Fenton reaction. The fluorescence intensity of CQD-AuNCs nanoaster was decreased as introducing H 2 O 2 to the probe, and can be applied to the determination of milk and toothpaste and cells imaging.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
APPLIED MICROBIOLOGY AND BIOTECHNOLOGY
·
2019
·Vol. 103
·期 9
·3715-3725
·
IF 3.67
Wang Chengcheng,Zheng Pu,Chen Pengcheng
Raspberry ketone is an important ingredient in the flavor and fragrance industries. Due to its low content in fruits and vegetables, the production of natural raspberry ketone using heterologous synthesis in microbial strains is recently attracting increased attention. In this work, a heterologous pathway to produce raspberry ketone from p -coumaric acid, including 4-coumarate: CoA ligase (4CL), benzalacetone synthase (BAS), and raspberry ketone/zingerone synthase (RZS1) from plants, was successfully assembled in Escherichia coli . When the RZS1 gene was introduced into E. coli and co-expressed with two other genes, the intermediate 4-hydroxybenzylidene acetone in the pathway was almost completely transformed into a raspberry ketone. Substituting TB medium for M9 medium increased raspberry ketone titers by 3–4 times. Furthermore, the heterologous pathway was partitioned into two modules; module one produced p -coumaroyl-CoA from p -coumaric acid by 4CL, and module two produced raspberry ketone from coumaroyl-CoA by the action of BAS and RZS1. Optimizing the balanced expression of the two modules, it was shown that moderate expression of module one and high expression of module two was the best combination to enhance raspberry ketone production. The engineered strain CZ-8 reached 90.97 mg/l of raspberry ketone, which was 12 times higher than previously reported. In addition, the preferred approach of the heterologous pathway was related to the heterologous genes from different sources; for example, 4CL from Arabidopsis thaliana seemed to be more suitable for raspberry ketone production than that from Petroselinum crispum . This work paves an alternative way for future economic production of natural raspberry ketone.
✓ 已验证
DOI
PubMed
高影响因子
CELLULOSE
·
2019
·Vol. 26
·期 5
·3167-3181
·
IF 3.917
Wu Canqing,Zhang Xuzhen,Wang Xiuhua,Gao Qingwen,Li Xinan
Abstract Cellulose nanocrystals (CNCs) extracted from microcrystalline cellulose, were modified by succinic anhydride to give succinic CNCs (SCNCs). Successful surface modification of SCNCs was confirmed by results of FTIR, FE-SEM, contact angle measurement and dispersity test, and SCNCs were then subjected to melt blending with poly(butylene succinate) (PBS) to prepare nanocomposites. Meanwhile, PBS/CNC nanocomposites were also prepared through same procedure as references. The morphology, thermal and mechanical properties and crystallization properties of PBS/SCNC nanocomposites with increasing SCNCs content from 0 to 7 wt% were investigated. PBS/SCNC nanocomposites exhibit better thermal stability than that of PBS/CNCs, which is mainly ascribed to less sulfate groups on CNC surfaces and more hydrogen bond effects between PBS carbonyl groups and ester groups from SCNCs. Young’s modulus and yield strength of PBS/SCNCs are higher than that of PBS/CNC nanocomposites, which is primarily attributed to the homogeneous dispersion of SCNCs in PBS matrix, confirmed by FE-SEM images. This work is valuable for design of PBS-based nanocomposites with enhanced thermal and mechanical properties. Graphical abstract
✓ 已验证
产品关联
DOI
高影响因子
CATALYSIS LETTERS
·
2019
·Vol. 149
·期 4
·1037-1045
·
IF 2.372
Du Feng,Wang Hongmei,Jin Xin,Deng Wenan,Li Chuan,Ren Zhixiang,Yan Hao,Yin Bin
This paper reported synergistic bimetallic AuCu/TiO 2 catalysts for selective oxidation of 1,2-propanediol to lactic acid under very mild conditions (T < 90 °C, 1 MPa O 2 ). The addition of Cu to monometallic Au/TiO 2 catalyst leads to a twofold activity enhancement for Au catalysts (TOF: 11894 h −1 ) with good selectivity towards lactic acid (S > 92%). Surface characterization reveals that while AuCu forms alloy structure with larger particle size based on TEM images, strong interaction between Au and Cu species is critical for performance enhancement. According to experimental studies on the influence of 1,2-propanediol and NaOH concentration on reaction rates, it is highly possible that 1,2-propanediol is reacted following single-site Langmuir–Hinshelwood mechanism while NaOH acts as a promoter and may block surface sites under relatively higher concentration. Graphical Abstract
✓ 已验证
产品关联
DOI
高影响因子
CHINESE JOURNAL OF POLYMER SCIENCE
·
2019
·Vol. 37
·期 5
·509-517
·
IF 2.804
Chen Yu,Yao Jian,Xu Ming-Ke,Jiang Zhi-Guo,Zhang Hao-Bin
Electrically conductive and flame-retardant maleic anhydride grafted high-density polyethylene (MA-HDPE) nanocomposites with satisfactory mechanical properties are fabricated by melt compounding MA-HDPE with polyethyleneimine (PEI)-modified reduced graphene oxide (PEI@RGO) as the conductive nanofiller and brominated polystyrene (BPS) as the flame retardant. The modification with PEI significantly improves the interfacial compatibility and dispersion of the RGO sheets in the MA-HDPE matrix, leading to electrically conductive nanocomposites with enhanced mechanical properties. Furthermore, the addition of 25 wt% of BPS makes the nanocomposite flame-retardant with a UL-94 V-0 rating. Thus, the multifunctional RGO/MA-HDPE nanocomposites with good electrical, flameretardant, and mechanical properties would have potential applications in construction and pipeline fields.
✓ 已验证
产品关联
DOI
高影响因子
Carbon Letters
·
2019
·Vol. 29
·期 3
·225-232
·
IF 1.807
Reddy Sathish,Song Li,Kang Lixing,Feng Quinliang,Du Ran,Zhang Jin,He Liumin,Seeram Ramakrishna
Highly active, stable and low-cost noble metal-free electrocatalysts are essential for production of hydrogen. However, preparation of such catalysts is still highly challenging so far. In this work, the Mo 2 C–carbon nanomaterials have been prepared by controlled thermal technique. By controlling concentration of the reactants in the experimental condition, the Mo 2 C–carbon nanomaterials have been fabricated, which leads to decreases in contact resistance b/w Mo 2 C–carbon nanomaterials and graphitic carbon atoms. As a result, the Mo 2 C–carbon nanomaterial electrode shows remarkable activity for hydrogen evolution reactions with a small onset overpotential of 95 mV, a Tafel slope of 62 mV dec −1 , an high exchange current density of 0.32 mA cm −2 , good stability during long-term 1000 cycles and exhibits long-term durability for several days. This study opens a new method for the preparation of highly active non-noble electrode for production of hydrogen from water splitting.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF SOL-GEL SCIENCE AND TECHNOLOGY
·
2019
·Vol. 89
·期 3
·623-633
·
IF 1.986
An Zhimin,Ye Changshou,Zhang Rubing,Qu Qiang
Abstract A C/SiO 2 /SiC ternary aerogel was prepared from a formaldehyde–catechol/silicon source via the sol−gel method, supercritical drying, and high-temperature carbothermal reduction. The effects of different carbon/silicon molar ratios on the microstructure, chemical composition, and mechanical and shielding properties of the C/SiO 2 /SiC aerogels were investigated. The fabricated aerogels exhibited low density of 0.118–0.271 g/cm 3 , low thermal conductivity of 0.044 to 0.089 W/(m∙K) and a high specific surface area of 774 m 2 /g. The aerogel exhibited electromagnetic interference shielding effectiveness (SE) properties; the maximum SE value was 24 dB over 12.4–18.0 GHz with an absorption-dominant shielding characteristic. To improve the mechanical properties of the ternary aerogel, novel SiC w -C/SiO 2 /SiC aerogel composites were prepared by adding different contents of SiC whiskers into precursor solutions. The mechanism affecting thermal and mechanical properties of aerogel composites was investigated. This composite having high strength and low thermal conductivity had potential applications in space shuttles and reusable carrier thermal protection materials.
The fabricated C/SiO 2 /SiC ternary aerogels exhibited low density of 0.118–0.271 g/cm 3 and low thermal conductivity of 0.044−0.089 W/(m∙K). The aerogel exhibited electromagnetic interference shielding effectiveness (SE) properties; the maximum SE value was 24 dB over 12.4–18.0 GHz with an absorption-dominant shielding characteristic.
✓ 已验证
产品关联
DOI
高影响因子
Scientific Reports
·
2018
·Vol. 8
·期 1
·1-11
·
IF 4.122
Zhuang Xueheng,Zhang Ying,Cai Chang,Zhang Jing,Zhu Yuejin
Magnetic microencapsulated phase change materials (magnetic MicroPCMs) are hotly researched for their dual-functions with phase change and magnetic properties, which provided the new applications in fields of maneuverable phase change materials and infrared electromagnetic dual shield. A series of magnetic MicroPCMs samples are synthesized by polymerization and coprecipitation method and the chemical composition contained poly(MMA-MAA) @ n-octadecane modified by Fe 3 O 4 . In addition, the characterizations exhibit the excellent magnetic and phase change properties. The magnetic MicroPCMs samples present 20 emu·g −1 saturation magnetization with still high enthalpy of 132 J·g −1 , which fully illustrates that the magnetic MicroPCMs fulfill both application on thermal energy storage and magnetic control.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Scientific Reports
·
2018
·Vol. 8
·期 1
·1-11
·
IF 4.122
Zhang Xiaosheng,Niu Wenxing,Dai Yingjing,Xu Hong,Dong Jinxiang
Lubricating technologies are essential for saving energy and identifying effective, environmentally friendly layered materials that meet the demands of solid lubricants is an important direction. Herein, we probed the relationships between load-carrying capacity and crystal structure. The results showed that increasing the sliding resistance of interlayers using corrugated layers increased the load-carrying capacity of layered solid lubricants. This finding expands on the traditional lubrication mechanism of layered materials. Following the rules, rapid selection of layered potassium magnesium and calcium phosphates (K-LMP and K-LCP) as effective solid lubricants was achieved using crystallographic data and strict filtering criteria. In order to prepare materials suitable for lubrication, the synthesis of K-LMP and K-LCP was optimised. These materials could be utilised in the food, textile or marine machinery industries in the future. The developed method could successfully guide the synthesis of application-oriented materials.
✓ 已验证
产品关联
DOI
PubMed
高影响因子