ENERGY & FUELS
·
2021
·
IF 3.605
Ruzhen Cheng,Run Zou,Long He,Lei Liu,Chang Cao,Xinyuan Li,Xuhong Guo,Jun Xu
The precipitation and deposition of asphaltenes often cause great troubles to the recovery and transportation of crude oil. Adding polymer inhibitors is an effective approach to prevent asphaltenes from clogging. In this study, maleic anhydride-co-octadecene copolymers with imidazolyl, phenyl, and pyridyl pendants were synthesized. The inhibition behaviors of two extracted asphaltenes in the presence of these copolymers were investigated, which were also identified by the rheological tests of the heavy crude oil sample. The chemical structure of both asphaltenes was analyzed by Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance (NMR), elemental analysis, and time-of-flight (TOF) spectrometry. Both asphaltenes A and B have a high aromaticity and low H/C. However, asphaltene B has a much higher aromaticity and polarity than that of asphaltene A. Ultraviolet–visible spectroscopy, turbidity meter, and dynamic light scattering (DLS) were employed to determine the precipitation behaviors of asphaltenes in the absence and presence of copolymers. The influence of intrinsic properties of asphaltenes, polymer concentration, and aromatic group grafting ratio on asphaltene precipitation were also compared. It is found that the initial precipitation point (IPP) of both asphaltenes is increased most by the copolymer containing 2-aminopyridine (PMO-2-P), while the copolymer containing N-(3-aminopropyl)imidazole (PMO-I) shows the worst inhibition performance. It is because that pyridine group has a stronger adsorption capacity with asphaltene than the imidazole group. The effect of various functional groups in copolymers on inhibiting asphaltene precipitation conforms to the following sequence: 2-aminopyridine > aniline > 4-aminopyridine > N-(3-aminopropyl)imidazole. It is also found that high polymer concentration and grafting ratio are beneficial to inhibit the asphaltene precipitation. As a result of the π–π conjugation and hydrogen-bonding attractions between the aromatic groups in the copolymers and the asphaltenes, the polymers can be stably adsorbed onto the surface of the asphaltenes and prevent their aggregation.
✓ 已验证
产品关联
DOI
高影响因子
MATERIALS LETTERS
·
2021
·
IF 3.423
Huiling Zhang,Xiansheng Zhang,Lei Liu,Xiaoyu Pang,Langfei Yang,Bingjie Xu,Jindan Wu,Dongming Qi
Herein, a type of nanofibrous membrane was prepared by co-electrospinning of polycaprolactone, poly(methyl methacrylate), polyaniline, and roxithromycin. The temperature of the nanofibers increased by 20 °C with 1 min of near infrared (NIR) radiation, and then the drug release was accelerated significantly. The bactericidal rate toward Staphylococcus aureus reached 99% with the synergistic effect of heat and antibiotics. This study provides a new approach to solving the problem of bacterial resistance by synergistic strategies involving photothermal and on-demand release of drugs.
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2021
·
IF 9.229
Haikun Guo,Minghao Zeng,Xiang Li,Haibo He,Lixin Wu,Haolong Li
High ionic conductivity, good mechanical strength, strong electrode adhesion, and low volatilization are highly desired properties for flexible solid electrolytes. However, it is difficult to realize all these properties simultaneously, which needs a rational synergy of different electrolyte constituents. Here, we present the use of polyoxometalates as versatile enhancers to fabricate nonvolatile flexible hybrid polymer electrolytes with improved conductive, stretchable, and adhesive properties. These electrolytes are based on the molecular hybridization of a polyacrylate elastomer, phosphoric acid, and a commercial polyoxometalate H3PW12O40 (PW). PW can serve as a nanosized plasticizer to favor the chain relaxation of polyacrylate and improve stretchability. Meanwhile, PW as a solid acid can increase the proton concentration and form a hybrid hydrogen-bonding network to facilitate proton conduction. Besides, the strong adsorption ability of PW on solid surfaces enables the electrolytes with enhanced adhesion. The hybrid electrolyte with 30 wt % PW shows a break stress of 0.28 MPa, a break elongation of 990%, and a conductivity of 0.01 S cm–1 at 298 K, which are 1.8, 1.8, and 2.5 times higher compared to the case without PW, respectively. Moreover, PW enhances the adhesive strength of hybrid electrolytes on polypropylene, steel, and glass substrates. The flexible supercapacitors based on the hybrid electrolytes and polyaniline electrodes hold a stable electrode–electrolyte interface and exhibit a high specific capacitance of 592 mF cm–2 and an excellent capacitance retention of 84% after 6000 charge–discharge cycles. These results demonstrate great potential of polyoxometalates as multifunctional enhancers to design hybrid electrolyte materials for energy and electronic applications.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF CHROMATOGRAPHY A
·
2021
·
IF 4.759
Junnan Li,Yaming Sun,Longhui Liu,Hailiang Zhao,Wenjie Zhao,Lijun He,Shusheng Zhang
A 34-membered tetraazahexaphenylmacrocycle (N 4 Ph 6 ) with a rigid π-conjugated moiety was chemically bonded to silica gel with 3-chloropropyltrimethoxysilane as the coupling agent to prepare a novel SiO 2 @N 4 Ph 6 stationary phase. Several common organic analytes, including alkylbenzenes , polycyclic aromatic hydrocarbons , anilines, phenols, phthalates , and folic acid , were selected as probes to investigate its chromatographic performance. The as-developed SiO 2 @N 4 Ph 6 stationary phase showed superiority retention and high selectivity for probe molecules through multiple interactions, including hydrophobic, π–π, hydrogen-bonding, and steric interactions. Density functional theory calculation results using folic acid as model solute provided an intuitive and a quantitative description of the multiple retention mechanisms.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
SENSORS AND ACTUATORS B-CHEMICAL
·
2021
·
IF 7.46
Qi Hu,Zhenming Wang,Junyu Chang,Peng Wan,Jiahui Huang,Liang Feng
The accurate and rapid sensing of NH 3 at room temperature is a challenging conundrum for daily life and environment protection. In this work, we have explored an intriguing material, hollow NiO sphere composited with polyaniline (labelled as h-NiO-PANI) for NH 3 gas sensing, fabricated by growing PANI on the hollow NiO sphere derived from solvothermal synthesis and calcination. Ni-Cu glycerate is obtained via solvothermal synthesis, which is a universal way to produce uniform glycerate microspheres. During calcination, the hollow sphere is ingeniously designed by taking advantage of the outward adhesion from CuO to the inner core. Polymerization of aniline on the hollow spheres is beneficial for large specific surface area and gas adsorption. Impressively, the sensor based on h-NiO-PANI exhibits favorable response to NH 3 (ΔR/R 0 =43 % for 10 ppm, 149 s in response and 257 s in recovery), which is greatly better than the counterparts (NiO-PANI and PANI). Moreover, the sensor has also shown superb anti-interference against common volatile organic compounds (VOCs), water and humidity, along with the superior repeatability in 5 cycles and long-term stability in a week, manifesting the sensor a promising candidate in daily application. The enhanced gas sensing performance is attributed to the hollow structure and construction of p-p heterojunctions between NiO and PANI.
✓ 已验证
产品关联
DOI
高影响因子
ANALYTICAL CHEMISTRY
·
2021
·
IF 6.986
Yang Li,Rui Han,Min Chen,Leyao Zhang,Guixiang Wang,Xiliang Luo
Biofouling represents a serious challenge for the assaying of disease markers with various biosensors in complex biological samples due to the accompanied nonspecific protein adsorption. Herein, a highly sensitive and antifouling biosensing interface was constructed based on a cost-effective inert protein bovine serum albumin (BSA) cross-linked with polyaniline nanowires (PANI-NWs). Compared with the physically adsorbed BSA that was commonly used to block nonspecific adsorption or binding of proteins, the cross-linked BSA exhibited a significantly enhanced antifouling capability. The BSA/PANI-NW-modified electrode interface possessed excellent antifouling capability and electrochemical activity owing to the presence of the cross-linked BSA and the conducting polymer polyaniline. With further immobilization of the peptide aptamer for immunoglobulin G (IgG) recognition onto the BSA/PANI-NW interface, an electrochemical biosensor with excellent selectivity and sensitivity was prepared. The IgG biosensor possessed a linear range from 1.0 ng mL–1 to 10 μg mL–1 and a low detection limit of 0.27 ng mL–1, and it was capable of assaying IgG in complex human serum samples with acceptable accuracy when compared with the assay results obtained using commercial enzyme-linked immunosorbent assay kits. It is expected that the unique BSA-cross-linked conducting polymers can be used for the construction of various electrochemical sensors and biosensors that can be applied in complex biological media.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Journal of Coatings Technology and Research
·
2021
·Vol. 18
·期 4
·999-1012
·
IF 2.382
Situ Yue,Guo Yanlin,Ji Weiwei,Liu Defei,Wei Dan,Huang Hong
Polyaniline (PANI) encapsulated α-zirconium phosphate (α-ZrP) nanocomposites (PANI/α-ZrP) were prepared by in situ oxidative polymerization and used as anticorrosive filler in epoxy coatings. Water absorption test and electrochemical measurements in 3.5 wt.% NaCl solution were conducted to assess the barrier properties and anticorrosion performances of different coating systems. PANI/α-ZrP composite epoxy coating showed remarkably enhanced corrosion resistance comparing to neat epoxy coating because of “maze effect” from α-ZrP and “passivation effect” from PANI. The α-ZrP nanosheets could be completely encapsulated by PANI with appropriate PANI/α-ZrP mass ratio, and the resulting nanocomposite exhibited optimal corrosion protection properties.
✓ 已验证
产品关联
DOI
高影响因子
COLLOIDS AND SURFACES B-BIOINTERFACES
·
2021
·
IF 5.268
Liwen Fu,Shuguang Yang,Shichao Jiang,Xiaojun Zhou,Zhou Sha,Chuanglong He
Advances in nanotheranostics have promoted the development of precision medicine, which has great potential as a weapon for clinical diagnosis and therapy of tumors. However, the combination of three functional principle components (imaging probes, therapeutic agents and surface coating) in traditional theranostic system is difficult to be achieved in only one step, while undergoing multiple synthesis procedures, time-consuming process and unknown toxicity. Herein, we fabricated iodinated polyaniline ( [email protected] ) nanoparticles via a facile one-step synthesis approach integrating chemical oxidative polymerization and iodine-doping process for computed tomography (CT) imaging and photoacoustic (PA) imaging-guided photothermal therapy (PTT). Iodic acid (HIO 3 ) as an oxidant induces chemical oxidation polymerization of aniline monomers. Meanwhile, iodine is incorporated into the polyaniline structural units in the process of polymerization to obtain [email protected] nanoparticles. Moreover, the l -cysteine (LC) has an effect on diameter of [email protected] nanoparticles, which enables nanoparticles have size-controlled spherical morphology and good colloidal stability. The hemolysis assay and cytotoxicity assessment verified the good biocompatibility of [email protected] Moreover, our [email protected] nanoparticles could not only exhibit appealing PTT efficiency, but also achieve excellent CT/PA dual-mode imaging effect. The histological evaluations suggested the negligible toxicity of [email protected] in vivo . This is the first time to our knowledge that multifunctional [email protected] nanoparticles were prepared by an ingenious one-step method. This work not only highlights a one-step strategy that simplified the complex synthesis of [email protected] nanoparticles, but also provides insight for further biomedical application of “all-in-one” theranostic agent.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF CHROMATOGRAPHY A
·
2021
·
IF 4.759
Min Sun,Juanjuan Feng,Xiangping Ji,Chunying Li,Sen Han,Mingxia Sun,Yang Feng,Jiaqing Feng,Haili Sun
To improve extraction performance of carbon fibers (CFs) towards phthalate esters (PAEs), titanium dioxide (TiO 2 ) nanorods array was in-situ grown on the surface of CFs, then polyaniline (PANI) was used to modify it. PANI/TiO 2 nanorods-CFs were placed into a polyetheretherketone tube for solid-phase microextraction (SPME). Combining the tube to high performance liquid chromatography (HPLC), it was evaluated and displayed good extraction performance for several PAEs. Compared with bare CFs, TiO 2 nanorods and PANI, PANI/TiO 2 nanorods presented best performance, attributed to the unique advantages between high surface area of TiO 2 nanorods and multiple adsorption interactions (like π-π stacking, hydrogen bond ) of PANI. After the optimization of the important factors (sampling volume, sampling rate, sample pH, concentrations of organic solvent and salt in sample, and desorption time), the online in-tube SPME-HPLC method was established. It provided low limits of detection (0.01-0.05 μg L −1 ) and wide linear ranges (0.03-30, 0.10-30, 0.17-30 μg L −1 ) with correlation coefficients larger than 0.9991. The relative standard deviations (n=6) between intra-day and inter-day tests were in the ranges of 3.5-10.3% and 4.7-13.9%, respectively. The method was successfully used to determine seven PAEs in real water samples. Besides of satisfactory durability, the material also exhibited superior extraction performance than some materials.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF HAZARDOUS MATERIALS
·
2021
·
IF 10.588
Shuangshuang Li,Yi He,Liyun Zhang,Jianbo Li,Yiling Nie,Hongjie Li,Xiangying Yin,Yang Bai
Purification of insoluble emulsified oils and soluble organic pollutants from sewage has attracted tremendous attention in today's society. Herein, a stable and environmentally friendly nanofibrous membrane with hierarchical caterpillar-like structure was fabricated via in-situ hydrothermal growing the nickel-cobalt layered double hydroxides (NiCo-LDHs) on tche polyacrylonitrile (PAN) electrospun nanofibers. The wrapped hydrophilic NiCo-LDHs constructed the hierarchical structure and endowed the membrane attractive superhydrophilicity (≈ 0°)/underwater superoleophobicity (≈ 161°) and enhanced oil-repellency performance. Meanwhile, the NiCo-LDH@PANI/oPAN NFMs can display the ultra-fast flux of SSEs (xylene/water emulsion, 4175 L m −2 h −1 ) and satisfactory separation efficiency (99.07%). Moreover, the introduction of positively charged NiCo-LDHs increased plentiful adsorption active sites for membranes, which is beneficial to demulsify ionic SSEs and adsorb organic pollutants. Finally, for simultaneous purification of complex sewage by the dead-end and cross-flow filtration experiment, the composite membrane both displayed splendid removal rate of oil (> 99.0%) and dyes (> 99.0%), robust regeneration recycle-ability and no secondary pollution. Hence, it is expected that such strategy of combining electrospun and chelating-assisted in-situ hydrothermal can provide a low energy consumption and high decontamination technology for severe environmental crisis.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
NEW JOURNAL OF CHEMISTRY
·
2021
·Vol. 45
·期 5
·2765-2774
·
IF 3.591
Sheng Wang,Wei Lian,Hengdong Ren,Jialin Ma,Yin Liu,Tianshu Zhang,Ling Bing Kong
It is a bold and highly novel attempt to disperse a conductive polymer with clay to enhance its microwave absorption performance. In this paper, we demonstrate that the introduction of palygorskite can effectively prevent polyaniline from aggregation and guide polyaniline on the nanorods of palygorskite. Interestingly, the obtained palygorskite/polyaniline (PAL/PANI) composites exhibit a cross-linked shell structure and the thickness of the polymer shell can be adjusted by controlling the content of palygorskite, which has a positive effect on the microwave absorption performance of the materials, due to improved impedance matching and increased attenuation constant. The optimized sample shows a reflection loss (RL) value of −57.40 dB at 11.04 GHz, at a thickness of 2.41 mm. Meanwhile, the effective absorption bandwidth reaches 5.20 GHz in the range of 11.84–17.04 GHz. It is believed that this achievement can be used as a reference for the design of composite materials as low-cost high-performance microwave absorbers.
✓ 已验证
产品关联
DOI
高影响因子
SYNTHETIC METALS
·
2020
·
IF 3.286
Anfeng Zhu,Honglong Xing,Qi Fan,Xiaoli Ji,Ping Yang
Sheet aluminum powder was used as the substrate and aniline as the polymer monomer, to design novel Al/PANI composites via in-situ polymerization, which exhibited high electromagnetic wave absorption properties and low infrared emissivity. These unique bifunctional composite were systematically characterized by X-ray powder diffraction, Fourier transform infrared spectroscopy , scanning electron microscope, IR-2 dual-band emission rate measuring instrument and vector network analyzer. The calculated results showed that the maximum reflection loss value of Al/PANI composite reached −46.09 dB at 14.56 GHz with a film thickness of only 1.0 mm. Meanwhile, the infrared emission rate of the composite was 0.55. The excellent electromagnetic absorption performance may be ascribed to its superior conductivity and unique structure. The merits of as-synthesized composites with high-performance microwave absorbing properties and low infrared emissivity indicate the potential use of Al/PANI composites in the applicable stealth fields.
✓ 已验证
产品关联
DOI
高影响因子