JOURNAL OF FOOD SCIENCE
·
2022
·Vol. 87
·期 9
·4027-4039
·
IF 3.693
Miral Javed,Tarun Belwal,Hao Huang,Yanqun Xu,Fatima-ezzahra Ettoumi,Li Li,Xuezhi Fang,Zisheng Luo
Camellia oleifera shells are abundant in polyphenolic compounds. Green extraction methods of polyphenolic compounds are essential to ensure product quality, efficiency, process cost, environment, and safety. This study investigated the effect of Tween 80 and Rhamnolipid surfactants on the production and utilization of stabilized carbon dioxide nanobubbles (CO 2 -NBs). The results confirmed the presence of the CO 2 -NBs in ultra-pure water with a concentration of 8.45 ± 1.05 × 10 8 ml –1 , among which the stable CO 2 -NBs possessed a mean size of 40–90 nm and a negative zeta potential (−41.6 ± 1.3 mV). Further, the efficiency of CO 2 -NBs combined with ultrasonication (CO 2 -NBs-Rh-UAE) was evaluated to extract polyphenols from Camellia oleifera shells (waste). The CO 2 -NBs treatment with ultrasonication showed the highest total phenolic content (TPC) and total flavonoid content (TFC) (36.75 ± 0.22 mg GAE/g DW and 24.06 ± 0.22 mg RE/g DW, respectively). Overall, this study demonstrated an innovative approach for producing, stabilizing, and utilizing biosurfactant stabilized CO 2 -NBs to extract polyphenolic compounds from the waste agricultural products. These findings highlighted the potential application of biosurfactant-stabilized CO 2 -NBs.
✓ 已验证
DOI
PubMed
高影响因子
Molecular Catalysis
·
2023
·
IF 4.6
Dou Zhang,Bo-hui Li,Yi-lei Li,Jun Zhao,Xiao-jing Wang,Fa-tang Li
The efficient conversion of CO 2 to carbon-neural fuels by photocatalysts can effectively address the increasingly prominent challenges of environmental pollution and energy shortage. TiO 2 is considered a promising photocatalyst. However, its disadvantages, such as poor adsorption of CO 2 and low carrier separation efficiency, inhibit its performance and selectivity in photocatalytic CO 2 reduction. Herein, K + -modified anatase TiO 2 ultrathin nanosheet photocatalysts were obtained via a reverse etching method using K 2 Ti 8 O 17 as the precursor. The selectivity of the optimized photocatalyst for methane was 96.02% in a gas–solid system without additives, with an excellent photocatalytic rate of 42.3 μmol·g −1 ·h −1 , which was 3.39 times higher than that of P25. The effects of K + on photocatalytic behaviors and the selectivity of CH 4 was systematically investigated. The test results showed that during treatment with formic acid, a large amount of K + from the layered K 2 Ti 8 O 17 were removed and the original structure was destroyed. Therefore, highly dispersed TiO 2 nanosheets were obtained, with a small amount of K + remaining on the TiO 2 surface. The well-defined rectangular shapes of TiO 2 reduce the transmission distance of photogenerated carriers, whereas the presence of K + increase the chemisorption of CO 2 molecules, thereby activating CO 2 , promoting the conversion of bridge *CO to -CHO, and increasing CH 4 production. This study provides insightful references for the preparation and modification of traditional photocatalysts for photocatalytic CO 2 reduction reactions.
✓ 已验证
DOI
高影响因子
CHINESE JOURNAL OF CATALYSIS
·
2023
·
IF 16.5
Zhuogen Li,Qadeer Ul Hassan,Weibin Zhang,Lujun Zhu,Jianzhi Gao,Xianjin Shi,Yu Huang,Peng Liu,Gangqiang Zhu
The H 2 evolution is generally considered a competing reaction in photocatalytic CO 2 reduction reaction (CO 2 RR) using H 2 O as the proton source. However, the reducing gas H 2 generated from H 2 O splitting can be the proton source in CO 2 RR under the enhanced dynamic role of the thermal effect. The reverse water gas shift (RWGS) reaction, a CO 2 hydrogenation reaction, should occur in photothermal environment owing to thermodynamically and kinetically favorable. Herein, nanostructured metal-semiconductor contact consisting of Pt nanoparticles (NPs) supported on SrTiO 3– δ nanosheets with rich oxygen vacancies (Pt-OVs-STO) was constructed for investigating its feasibility and efficiency in the RWGS reaction under photothermal effect. Our experimental results substantiate that the H 2 generated by H 2 O splitting effectively contributes to the RWGS reaction over Pt-OVs-STO system. The Pt 0 NPs not only efficiently facilitate surface charge transfer, but also lower the energy barrier of the O–H bond breaking, H 2 releasing, and RWGS reaction, thereby showing an outstanding CO 2 RR performance. The strong interaction between the Pt 0 NPs and SrTiO 3– δ has been extensively demonstrated by a series of experimental characterizations and density functional theory calculations. This work elucidates the relation between H 2 evolution and RWGS reaction over Pt 0 /SrTiO 3– δ structure in photothermal catalytic CO 2 RR using H 2 O as the proton source and provides new perspectives for subsequent CO 2 RR.
✓ 已验证
DOI
高影响因子
DYES AND PIGMENTS
·
2017
·
IF 3.473
H.C. Ma,Z.M. Yang,H.Y. Cao,L. Lei,Z.Q. Lei
The development of CO 2 -active fluorescent sensors is paramount to the climate assessment. And also, because of the biological and environmental importance, trace detection F − is a great challenge task but very necessary for human daily life. This paper presented a water-soluble fluorescent sensor fabricated by triphenylamine derivative of NBTA 3− and quaternary ammonium salt (CTAC), which was further explored as a green and multi-functional sensing platform, and demonstrated excellent CO 2 response ability and trace amount of F − recognition with obvious visualized exhibitions. Especially, our research result has potential application in the CO 2 sensing by contact and vapor modes. Both of techniques exhibited reliable and sensitive and quick CO 2 sensing capability. We hope our research result is of real-time monitoring CO 2 in our surroundings.
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2018
·
IF 6.735
Haiyan Yang,Wenzhe Li,Jun Liu,Yankun Sun,Wanzhen Liu
Adsorbents prepared by impregnating porous materials with polyethylenimine (PEI) are potential candidates for CO 2 capture from biogas. The objective of current research is to investigate the effect of structures of resins on CO 2 capture performance of PEI-impregnated resins from simulated biogas. Here, three commercially available resins (D101, X-5 and ADS-17) with different pore volumes or surface functional group were selected as supports. N 2 adsorption-desorption, infrared spectroscopy, scanning electron microscopy and thermal gravimetric analysis were used to characterize the resins before and after impregnating PEI. Breakthrough experiments revealed that all these PEI-impregnated resins could selectively adsorb CO 2 at ambient temperature. Meanwhile, PEI-impregnated ADS-17 exhibited a superior performance among the tested adsorbents, despite that it had the lowest BET surface area and total pore volume. It is mainly because that ADS-17 had uniform voids and carbonyl group, enhanced the dispersion of PEI and thus improved the CO 2 adsorption performance. In addition, ADS-17-20% PEI possessed excellent regenerability. The influence of gas flow rate and temperature on the CO 2 adsorption behavior upon ADS-17-20% PEI was also investigated. It was found that the adsorption capacity did not depend much on the flow rate when the gas flow rate ranging from 100 to 200 mL/min. When the temperature was increased from 25 to 45 °C, a slight increase in CO 2 adsorption was observed. Furthermore, CO 2 adsorption performance of ADS-17-20% PEI can be improved under humid condition.
✓ 已验证
DOI
高影响因子
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2020
·
IF 3.573
Jiuli Han,Lu Bai,Haiyan Jiang,Shaojuan Zeng,Bingbing Yang,Yinge Bai,Xiangping Zhang
Ionic liquids (ILs) have become attractive in membranes for CO2 separation because of the designable structure, high CO2 affinity, and good compatibility and stability. Modification of metal–organic frameworks with ILs is an effective strategy to improve the gas separation performance of mixed matrix membranes (MMMs). In this work, task-specific ionic liquids (TSILs) were incorporated to prepare TSIL@ZIF-67/PIM-1 MMMs and improve CO2 separation performance because of the high CO2 solubility and great compatibility toward ZIF-67 and PIM-1. The TSILs (TMGHIM and TMGHPhO) selectively and reversibly interact with CO2 and improve the interfacial compatibility between ZIF-67 and PIM-1, leading to higher CO2/CH4 and CO2/N2 selectivities than that of the ZIF-67/PIM-1 MMM and the directly blended membrane (TSIL/ZIF-67/PIM-1). The 10 wt % TMGHIM@ZIF-67/PIM-1 MMM shows enhanced CO2/N2 and CO2/CH4 selectivities of 13.7 and 10.5, respectively; meanwhile, the CO2 permeability reaches 12,848.5 Barrer and is 2.5 times that of the pure PIM-1 membrane. The TSIL@ZIF-67/PIM-1 MMMs also show good stability against physical aging.
✓ 已验证
DOI
高影响因子
ENERGY & FUELS
·
2022
·
IF 4.654
Liu Zhang,Fangping Ma,Qing Zeng,Fang Peng,Qiang Hu,Kejing Wu,Yixue Yang,Houfang Lu,Bin Liang
Methanation of CO2 in biogas could realize CO2 utilization; meanwhile, the biogas is upgraded. In this study, a methanation catalyst was designed and the system efficiency considering a solid oxide electrolysis cell (SOEC) was evaluated. A layered nickel silicate catalyst was synthesized and modified by doping with trace amounts of precious metal Pt and alkaline-earth metal Mg. The conversion of CO2 reached 79% with 100% selectivity toward CH4 for model biogas with 50 vol % CO2 and 50 vol % CH4 over the Pt- and MgO-doped Ni/SiO2 catalyst at 350 °C. A simulation system consisting of SOEC and methanation of simulated biogas is built with commercial software Aspen Plus. The energy efficiency was analyzed and optimized through a heat exchange network, which achieved about 30% increase in efficiency. The energy utilization efficiency can be greater than 86% when the CO2 conversion in biogas is greater than 99% by adjusting the methanation temperature and H2/CO2 ratio. The energy efficiency in direct methanation of biogas exceeds 8% higher than that in methanation of CO2 separated from biogas.
✓ 已验证
DOI
高影响因子
JOURNAL OF MEMBRANE SCIENCE
·
2018
·
IF 6.578
Ke Chen,Kai Xu,Long Xiang,Xiao Dong,Yue Han,Chongqing Wang,Lin-Bing Sun,Yichang Pan
Mixed matrix membranes (MMMs) derived from metal-organic frameworks (MOFs) nanocrystals represent a promising alternative for overcoming the trade-off between permeability and selectivity derived from the pristine polymeric membrane . The selection of MOFs fillers are mainly focused on their diffusion-selectivity property for gas-pairs. However, the improvement of both gas-permeability and selectivity through addition of sorption-selective MOFs are rarely reported. Herein, the incorporation of CO 2 -philic KAUST-7 (also referred to as NbOFFIVE-1-Ni) nanocrystals makes the neat 6FDA-Durene polyimide membrane more permeable and more selective, surpassing the state-of-the-art 2008 Robeson upper bound for CO 2 /CH 4 . Nano-sized (~ 80 nm) KAUST-7 crystals with sharp particle size distribution were first fabricated through a co-solvent synthesis method. The explored gas transportation mechanism indicates that the improvement of CO 2 /CH 4 selectivity on MMMs are attributed to the significant raise of the sorption-selectivity rather than the diffusion-selectivity. The favorable interfacial interaction between the imide groups of the 6FDA and the H of the pyrazine in the KAUST-7 enhances plasticization resistance of the neat polymer membrane. The developed MMMs exhibit a promising application in CO 2 capture from natural- and bio-gas.
✓ 已验证
DOI
高影响因子
Journal of CO2 Utilization
·
2016
·
IF 4.764
Xian-Dong Lang,Yi-Chen Yu,Zheng-Ming Li,Liang-Nian He
Despite recent renaissance of CO 2 chemistry, transformation of CO 2 at ambient conditions remains still of great challenge. In this work, an easily prepared protic ionic liquid e.g. 1,1,3,3-tetramethylguanidinium imidazolide [HTMG][Im] was developed as highly efficient, recyclable and bifunctional catalyst for the carboxylative cyclization of 2-aminobenzonitriles with CO 2 at atmospheric pressure and room temperature. The catalytic protocol was found to be applicable to various 2-aminobenzonitriles bearing electron-withdrawing or electron-donating substituents, affording the corresponding quinazoline-2,4(1H,3H)-diones in moderate to excellent yields. In addition, the catalyst could be conveniently recovered and reused for five cycles with almost consistent activity. Consequently, this process represents an alternative approach for the efficient and greener chemical fixation of CO 2 to afford valuable heterocycles.
✓ 已验证
DOI
高影响因子
APPLIED CATALYSIS B-ENVIRONMENTAL
·
2018
·
IF 11.698
Meichao Gao,Jinxiang Yang,Tao Sun,Zizhong Zhang,Dafeng Zhang,Huijuan Huang,Huaxiang Lin,Yi Fang,Xuxu Wang
The photocatalytic overall conversion of CO 2 with H 2 O to chemical fuel and oxygen mimicking natural photosynthesis is a huge challenge in photocatalysis. This work shows the achievement of the solar-driven photocatalytic overall CO 2 reduction with H 2 O to CO and O 2 over a Persian buttercup-like BiOBr x Cl 1-x solid solution. A CO generation rate of 15.86 μmol g −1 h −1 with the approximate stoichiometric O 2 evolution is yielded on BiOBr 0.6 Cl 0.4 solid solution under simulated solar light irradiation, which was about 7.5 and 10.2 times higher than that of pure BiOCl (2.11 μmol g −1 h −1 ) and BiOBr (1.55 μmol g −1 h −1 ), respectively. The enhanced photoactivity is contributed to the mediate band gap and energy level tuned by the formation of BiOBr x Cl 1-x solid solution to facilitate the separation of photogenerated charges. Besides the unique electron structure, the photoinduced oxygen vacancy (O V ) formed on BiOBr x Cl 1-x solid solution also plays an important role in the CO 2 reduction.
✓ 已验证
DOI
高影响因子
CRYSTAL GROWTH & DESIGN
·
2021
·
IF 4.076
Yichen Jiang,Zhijiang Wang,Ping Xu,Jianmin Sun
Dicationic ionic liquid 1,1′-(hexane-1,6-diyl)-bis(3-methylimidazolium) dibromide was synthesized inside an MIL-101 metal–organic framework via a facile ship-in-bottle technique. The resultant dicationic ionic liquid @MIL-101 composite contains Cr sites as a Lewis acidic center and Br– as a nucleophile. The high BET surface area (1162 m2/g) and good synergic effects between the dicationic ionic liquid and MIL-101 resulted in good CO2 sorption capacity (47.4 cm3/g at 273 K) and high catalytic activity for the cycloaddition reaction of CO2 with epoxide without any cocatalyst or solvent, and a 92.5% propylene carbonate yield was obtained under 100 °C, 1.0 MPa for 2.5 h. Moreover, the dicationic ionic liquid @MIL-101 composite also showed better recycling stability and easy separation in the CO2 cycloaddition reaction. Compared with the complex synthetic route for the reported ionic liquid functional metal–organic frameworks, the facilely synthesized dicationic ionic liquid @MIL-101 composite exhibited comparable performance in CO2 capture and utilization.
✓ 已验证
DOI
高影响因子
ACS Sustainable Chemistry & Engineering
·
2023
·
IF 8.4
Yingshu Wang,Shuyue Wang,Jiasi Gan,Jinni Shen,Zizhong Zhang,Huidong Zheng,Xuxu Wang
One-pot synthesis of urea [(NH2)2CO] from easily available small molecules, that is, N2, CO2, and H2O, is an extremely attractive but very challenging reaction. 2D-CdS@3D-BiOBr composites with S-scheme heterojunctions are constructed via a facile hydrothermal technique followed by a self-assembly method and shown to be an excellent photocatalyst enabling the reduction of N2 and CO2 with H2O to (NH2)2CO under visible light. The optimal 40%2D-CdS@3D-BiOBr sample shows up to 15 μmol·g–1·h–1 total yield of NH3 and (NH2)2CO, of which (NH2)2CO accounts for 54%. The apparent quantum efficiency (AQE) is 3.93% for urea production. On the photocatalyst, urea is speculated to form by two possible chemical routes. One is direct photocatalytic synthesis. Both N2 and CO2 molecules are activated by the Cd2+ ion of 2D-CdS and the oxygen defect of 3D-BiOBr at the edges of the heterojunction interface of 2D-CdS/3D-BiOBr, respectively. *HNCONH* is the key intermediate of the formation of (NH2)2CO molecules. The other is indirect synthesis by photocatalysis and then thermocatalysis. N2 is reduced into NH3 and CO2 is reduced into CO on 2D-CdS by the photogenerated electrons and protons, and then the formed NH3 reacts with the reactant CO2 or the product CO to form (NH2)2CO by thermocatalysis on 2D-CdS. The former is dominant for urea synthesis. The work confirms that urea could be synthesized photocatalytically from cheap N2, CO2, and H2O under visible light. A composite heterojunction semiconductor could be a prospective photocatalyst appropriate for the complex reaction.
✓ 已验证
DOI
高影响因子