SENSORS AND ACTUATORS B-CHEMICAL
·
2022
·
IF 9.221
Qing Zhang,Shangshang Ma,Li Zhang,Hongyan Wang,Xin Zhuo,Guizhi Wang,Yanyun Shen,Keying Zhang,Shao Su
Microfluidic chip for sensing heavy metal ions has been strongly attended due to its merits, but still remains a large challenge from long analysis time derived from the preconcentration process of metal ions. Herein, a heated flow channel was manufactured by 3D printing combined with a filter paper to construct a microfluidic chip, the thermocapillary convection strategy was introduced to accelerate ions migration, allowing for rapidly recognizing metal ions. The MnO 2 nanosheets-Au nanostars (MnO 2 NSs-AuNSs) film was employed as modifier to fabricate a flexible screen printed electrode (SPE) for high-efficiency detecting metal ions based on thermocapillary convection accelerating accumulation method. To verify the proposed strategy, the detection of Cu 2+ was chosen as a model. The results revealed that the proposed strategy possessed a rapid detection to Cu 2+ , which greatly improved the detection efficiency (saved 400 s of preconcentration time) and achieved a detection limit down to 0.0270 ppb. Interestingly, the constructed method was successfully used to evaluate Cu 2+ concentration in sweat samples with satisfactory results. This proposed method maybe provide new insight to develop a novel approach to rapidly and sensitively detect metal ions, which possess huge utilization potentiality for safeguarding human health.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2022
·
IF 9.965
Mingyang Li,Wanlu Zhang,Xuewei Zhang,Yongfu Lian,Xiaoyu Niu,Yujun Zhu
Catalytic oxidation is considered as the most effective and economical method to remove low concentration volatile organic compounds (VOCs). Activation of oxygen to form active oxygen species on metal oxides catalyst plays a key role in the process. Three copper-manganese oxide catalysts with cubic Cu 1.5 Mn 1.5 O 4 phases were prepared by microwave heating (CM-MW), sol–gel (CM-SG) and co-precipitation (CM-CP) methods, and applied for the elimination of toluene and benzene as representative aromatic VOCs. These catalysts exhibit different catalytic oxidation performance due to their different physicochemical properties. Various characterizations were used to clarify the role of different oxygen species in the oxidation of VOCs, and the reaction pathway. In situ DRIFTS were carried out to explore the function of surface adsorbed oxygen, oxygen vacancy , and surface lattice oxygen in the catalytic oxidation of VOCs over three catalysts. Various types of intermediate species and detailed reaction pathways are also explored by combining in situ DRIFTS and mass spectrometry . Among these catalysts, CM-MW with nanosheet morphology shows the best catalytic oxidation performance of toluene and/or benzene with/without H 2 O due to the most abundant active oxygen species, and the highest oxygen vacancy concentration which is beneficial to activate oxygen. Meanwhile, toluene and benzene do not interfere with each other during the mixture oxidation. This study can provide new inspiration for rational design of metal oxide catalysts to remove VOCs.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ANALYST
·
2022
·Vol. 147
·期 24
·5670-5679
·
IF 5.227
Ziyan Song,Siyu Chen,Qiushi He,Hu Liang,Guangyao Huang,Pan Li,Zongyao Hao,Liangbao Yang
The rapid and sensitive detection of ultra-trace marker molecules from biological samples is of great significance for the wide application of surface-enhanced Raman spectroscopy (SERS) methods in clinical diagnosis and disease monitoring. However, the cumbersome biological sample processing procedures and the poor enrichment of target analytes in hot spots hinder the practical applications of SERS methods. In this paper, we synthesized a novel floating SERS substrate by a simple one-step oxidation process, annealing and in situ chemical etching to form Ag-NPs@Cu-NW bundles on copper mesh (CM). In particular, under spontaneous bottom-up capillary action, the pressure difference at different nanogaps drives uric acid molecules to actively enter hot spots, so that the Ag-NPs@Cu-NW bundle nanostructure with the advantages of a light weight CM is capable of preventing the common coffee-ring effect and enhancing the spatial enrichment of analytes. Therefore, this SERS substrate realizes highly sensitive detection of uric acid at a level of 50 nM in pretreatment-free urine. Currently, this portable, flexible, simple, fast and cost-effective SERS substrate has great potential for early screening and clinical diagnosis of diseases in different biofluids.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF HAZARDOUS MATERIALS
·
2022
·
IF 14.224
Xiaoqing Lin,Canming Ma,Deli Wu
Metal-enhanced ozonation can greatly improve the decay of organic matter; however, whether this method benefits the decay of malodorous compounds or not and the possible mechanism are not well understood. In this study, nine typical malodorous compounds were selected to reveal that Cu(II)-enhanced ozonation can greatly promote the decay of fatty amines because of the direct ozone oxidation , which was enhanced to promote ozone utilization. Moreover, trace Cu(II) can amplify the observed rate constants of dimethylamine and trimethylamine for 48.9% and 155.7%, respectively, and Cu(II) dosage was the determining factor using response surface methodology to investigate the interactions between initial pH, Cu(II) dosage and ozone dosage. These results demonstrated that the formation of • OH and O 2 •– was inhibited rather than promoted, which was quite different from some previously reported Cu(II)-enhanced ozonation counterparts. Moreover, the enhanced effect of trace Cu(II) was exhibited in both single and complex malodorous compounds. The conversion pathway of nitrogen and sulfur elements was clarified, with the targeted mineralization of nitrogen of nitrogen-containing malodorous compounds into NO 3 -N and the odor characteristics of sulfur-containing malodorous compounds disappeared. These findings provided new insight for utilizing metal ions to enhance the direct ozone oxidation capacity of malodorous compounds.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
MATERIALS CHARACTERIZATION
·
2022
·
IF 4.537
Shuang Liu,Limin Ma,Cheng Zhen,Yishu Wang,Dan Li,Fu Guo
In advanced microelectronic packaging technology, the interfacial brittleness of Cu/Sn solder joints puts forward higher requirements for high-performance diffusion barriers. Cobalt–Phosphorus (Co-P) alloy coating becomes ideal candidates for its good wettability and diffusion resistance. In this work, for Co-P with different crystallinity , the barrier properties of electrodeposited Co-P coatings as well as the mechanical properties of Co-Sn intermetallic compounds (IMCs) at the Co-P/Sn-Ag interface were investigated. According to the XRD results, the crystallinity of the Co-P coating was directly related to the phosphorus (P) content, and Co-P were classified into three types: crystalline state, mixed state and amorphous state. The morphology, composition, phase characterization, and mechanical properties of the Co-Sn IMCs at the interface were investigated by SEM , EPMA , TEM , and nanoindentation methods, respectively. After 180 °C aging test for 120 h, the thickness of CoSn 3 generated at the interface of crystalline Co-4.2 at.% P/Sn-Ag was the smallest among a total of 18 Co-P coatings, where P content ranged from 0.9 at.% to 20.8 at.%, showing the best barrier properties. The hardness of (Co,Cu)Sn 3 at the amorphous Co-P/Sn-Ag interface was the lowest (3.2 GPa), which was only 47% of that of Ni 3 Sn 4 , exhibiting the lowest brittleness tendency. The mixed crystalline-amorphous Co-P could greatly improve the diffusion barrier properties while sacrificing a small degree of brittleness comparing to the amorphous coatings, and had the potential to become a general-purpose alloy coating. This work could provide a scientific basis for the selection of Co-P barrier layers with excellent barrier properties and mechanical properties leading to different application scenario in electronic packaging.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF INDUSTRIAL AND ENGINEERING CHEMISTRY
·
2022
·
IF 6.76
Muhammad Faizan,Hao Li,Yumei Liu,Kexin Li,Shuang Wei,Ruirui Zhang,Ruixia Liu
Currently, deep eutectic solvents (DESs), as an exclusive class of ionic liquid analogs, are extensively employed in various fields. Herein, vanadium phosphorus oxide (VPO) catalysts assisted by copper-based deep eutectic solvent (Cu-DES) as an electronic promoter and structure directing agent were ingeniously synthesized and exploited in the selective oxidation of n-butane to maleic anhydride (MA). The DES is efficient, cost effective and highly green compared to conventionally use metal inorganic modifiers. Cu-DES was prepared from a eutectic mixture of an organic salt (ChCl) and a metal salt hydrate/metal salt of cupric (Cu(NO 3 ) 2 .3H 2 O, CuCl 2 ) and cuprous (CuCl) salt with a molar ratio of 1:1–1:3, which notably improved the catalytic performance compared to that of an unpromoted VPO catalyst. The MA selectivity and n-butane conversion of Cu–DES–VPO increased significantly, while the CO x (CO and CO 2 ) selectivity decreased. FTIR, DSC , XRD, SEM, EDS, TEM, Raman, TGA, XPS, and NH 3 -TPD characterization techniques were utilized to fully analyze the DES, precursor and catalyst to explore MA selectivity. This work shifts the significant increase of 13% n-butane conversion, 11% MA selectivity and 16% MA mass yield, which greatly influences low carbon alkane utilization. Importantly, the CO: CO 2 ratio is reduced from 2.02 to 1.62, which is more beneficial for chemical plants as well as green environments.
✓ 已验证
产品关联
DOI
高影响因子
Carbon Energy
·
2022
·Vol. 4
·期 6
·1214-1227
·
IF 21.556
Zhicong Hu,Yongjin Zou,Cuili Xiang,Lixian Sun,Fen Xu,Menghe Jiang,Sensen Yu
The leakage of organic phase change materials (OPCMs) at temperatures above their melting point severely limits their large-scale application. The introduction of porous supports has been identified as an efficient leakage-proofing method. In this study, a novel carbonized Cu-coated melamine foam (MF)/reduced graphene oxide (rGO) framework (MF/rGO/Cu-C) is constructed as a support for fabricating stabilized multifunctional OPCMs. MF serves as the supporting material, while rGO and Cu act as functional reinforcements. As a thermal energy storage material, polyethylene glycol (PEG) is encapsulated into MF/rGO/Cu-C through a vacuum-assisted impregnation method to obtain PEG@MF/rGO/Cu-C composite with excellent comprehensive performance. PEG@MF/rGO/Cu-C exhibits high phase change enthalpies of 148.3 J g −1 (melting) and 143.9 J g −1 (crystallization), corresponding to a high energy storage capability of 92.7%. Simultaneously, MF/rGO/Cu-C endues the composite with an enhanced thermal conductivity of 0.4621 W m −1 K −1 , which increases by 463% compared to that of PEG@MF. Furthermore, PEG@MF/rGO/Cu-C displays great light-to-thermal and electric-to-thermal conversion capabilities, thermal cycle stability, light-to-thermal cycle stability, and shape stability, showing promising application prospects in different aspects.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF HAZARDOUS MATERIALS
·
2022
·
IF 14.224
Wenyang Fu,Zhongzheng Hu,Yingying Du,Pei Su,Yi Su,Qizhan Zhang,Minghua Zhou
The electrochemical reduction of nitrate to ammonia (ERNA) has become a green treatment technology for nitrate wastewater. However, strong adsorption for product caused high activation energy for product desorption in scaling relations, blocking activity of electrocatalyst in ERNA. Density functional theory (DFT) calculations indicated that constructing dual active sites (Cu and Co 3 O 4 ) could achieve strong adsorption of nitrate (−2.91 eV) with low desorbing energy barrier of ammonia (0.13 eV), breaking scaling relations. This dual active sites Co 3 O 4 /Cu electrode achieved a high ammonia yield rate of 684 µg mg cat − 1 h −1 with 94.6% faradic efficiency, surpassing single active site Co 3 O 4 and Cu electrodes. For mechanism, In-situ electrochemical characterization found the vital intermediates of *NH and *NH 2 , demonstrating that indirect reduction was the main pathway on Co 3 O 4 /Cu electrode. Thus, it is believed that building dual active sites on electrode is a reliable strategy to enhance ERNA for purifying industrial wastewater polluted by nitrate.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
TALANTA
·
2022
·
IF 6.556
Xiaobin Zhou,Mengjun Wang,Junyang Chen,Xingguang Su
Developing high-performance nanozyme for the construction of high-sensitivity biosensor platform is of great significance. Herein, we have designed and synthesized a Cu/N co-doped carbon-based nanozyme by anchoring Cu atoms on two-dimensional carbon nanosheet (Cu/NC NS). The Cu/NC NS possessed ultra-high Cu loading, superior peroxidase-like catalytic activity, great stability and reusability. Significantly, the Cu/NC NS exhibited high affinity towards H 2 O 2 and 3,3′,5,5′-tetramethylbenzidine (TMB) under acidic condition, which could induce obvious color changes of TMB in the presence of low H 2 O 2 concentration. By integrating the Cu/NC NS with β-galactosidase (β-Gal) and galactose oxidase (Gal Ox), a multienzyme cascade colorimetric sensing system was established for the detection of lactose and β-Gal, which realizing the assay of lactose and β-Gal in the linear ranges of 0.1–1.4 mM and 0.025–0.2 U/mL, respectively. And the limit of detection for lactose and β-Gal were 0.03 mM and 0.01 U/mL, respectively. Furthermore, this work achieved the accurate detection of the content of lactose in milk and the activity of β-Gal in human serum, exploiting a novel application for nanozyme in biosensing.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ACS Sustainable Chemistry & Engineering
·
2022
·
IF 9.224
Rui Guo,Dongdong Li,Rui Guan,Dechen Kong,Zheng Cui,Ziqi Zhou,Tianmin He
BaCeO3-based proton conductors have comparatively high-proton conductivity, but the low chemical stability and high sintering temperature seriously hinder their practical applications in protonic ceramic fuel cells. Herein, we demonstrate that this limitation can be conciliated by using a triple-doping strategy in a BaZr0.1Ce0.7Y0.2O3−δ (BZCY) electrolyte, where the triply doped BaCe0.7Sn0.1Dy0.15Cu0.05O3−δ (BCSDCu) exhibits better chemical stability and conductivity and lower sintering temperature compared with the pristine BZCY. The phase-pure BCSDCu can be obtained at the sintering temperature of 1100 °C prepared by solid-state reaction. The dense BCSDCu (>95%) is achieved at 1350 °C, which is significantly lower than the 1550 °C of BZCY. The BCSDCu presents competitive proton conductivity of 13.6 mS cm–1 under a moist H2 atmosphere at 600 °C. The anode-supported single cell with the BCSDCu (≈40 μm) as the electrolyte reaches the highest power density of 390 mW cm–2 at 600 °C. On the basis of the distribution of relaxation time analysis, we not only distinguish the contribution of grain and grain-boundary conductivities but also identify the rate-determining step of the single-cell performance. The protonic conductivities, mechanical properties, and impurity clean parts induced by grain size effects are discussed for the BCSDCu proton conductor.
✓ 已验证
产品关联
DOI
高影响因子
FUEL
·
2022
·
IF 8.035
Lili Gao,Langlang Qin,Haonan Wu,Xuelian Li,Kai Qi,Qun Yi,Jiandong Zhang,Lijuan Shi
Electrochemical reduction of CO 2 (CO 2 ER) to high value-added multicarbon (C 2+ ) is a viable way to promote carbon–neutral cycle. To date, copper (Cu) is reported as the most effective metal catalyst toward C 2+ , but it remains a challenge to achieve high selectivity and large current density. Incorporating ionic liquid in Cu-based catalysis has been proved an effective strategy, however, most reported methods are either involved too much ionic liquid (IL) as electrolyte or too complex & unstable. Herein, an ionic liquid-embedded Cu electrocatalyst (Cu-IL/GDL) was innovatively constructed through one-step electro-codeposition method, in which a kind of amino-ionic liquid, AFIL, was anchored to the gas diffusion layer (GDL) and embedded by the deposited Cu. Under the excellent synergy between Cu and AFIL, Cu-IL/GDL exhibits higher faradaic efficiency toward ethylene (C 2 H 4, 40.67%) and C 2 (C 2 H 4 and C 2 H 5 OH, 61.39%) when directing CO 2 to carbon-fiber side of electrode in H-cell. To be precise, more Cu (1 0 0) facet is stabilized by the capping effect of AFIL, being in favor for C–C coupling; meanwhile more AFIL + is embedded by the deposited Cu, making for the initiation of CO 2 ER. Thus, this paper proposes a facial and effective strategy to reinforce Cu (1 0 0) facet, and couple and heighten the virtues of ionic liquid and Cu during CO 2 ER toward C 2 .
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2022
·
IF 16.744
Yunning Chen,Lu Yang,Yingnan Sun,Renquan Guan,Di Liu,Jie Zhao,Qingkun Shang
A CDs@Cu-HQCA/TiO 2 flower composite photocatalyst (CDs: carbon dots, HQCA : 8-hydroxyquinoline-5-carboxylic acid) was constructed by exploiting the synergy of complex-sensitization, TiO 2 -morphology control, and carbon dot-surface modification. The photocatalytic degradation of phenol, norfloxacin, tetrabromobisphenol A and Cr (VI) by Cu-HQCA/TiO 2 particle, tube, diamond and flower-like show that the Cu-HQCA complex effectively extends the visible light absorption range of composite photocatalysts, and the flower morphology of TiO 2 not only improves the adsorption of pollutants but also enhances the photoelectric response of the composite photocatalyst. In this manner, a CDs@Cu-HQCA/TiO 2 flower catalyst that demonstrates excellent performance for the removal of dexamethasone, which does not degrade well naturally, was prepared, which delivered a rate of degradation of 99.4% and a degree of mineralization of 77.4% for dexamethasone. Possible degradation sites and dexamethasone degradation products were studied by combining computational chemistry with high-resolution mass spectrometry, and a possible mechanism for photogenerated carrier transmission and separation in the CDs@Cu-HQCA/TiO 2 flowers is proposed.
✓ 已验证
产品关联
DOI
高影响因子