CHEMICAL ENGINEERING JOURNAL
·
2025
·
IF 13.2
Yuqi Zhang,Yaxuan Zhen,Chunying Zhu,Taotao Fu,Youguang Ma
Chemical absorption has become the most mature and widely used CO 2 capture technology to address CO 2 emissions. Phase change absorbents based on mixed amines combine the advantages of individual amines and reduce regeneration energy consumption. A novel phase change absorbent system based on mixed amine was developed in this study and its CO 2 capture and desorption performance was investigated. The system comprises monoethanolamine (MEA), N-methyldiethanolamine (MDEA), n-butanol and water. Gas-liquid absorption experiments in the microchannel revealed that the flow patterns of the rich phase changed successively through homogeneous flow, irregular droplet flow, tubular-droplet flow and liquid slug flow as the gas-liquid ratio was increased. This transition was influenced by internal circulation, phase change and viscosity, causing the absorption rate to rise initially, then increase slowly before eventually declining. The desorption performance of the saturated rich phase in the MEA-MDEA-n-butanol-H 2 O system was significantly superior to that of the 30 wt% MEA aqueous solution. Comprehensively, the optimal mass ratio of MEA-MDEA-n-butanol-H 2 O was identified as 1.2:1.8:4:3, achieving a higher desorption rate and lower energy consumption. Desorption efficiency and cyclic capacity were 1.8 times those of the 30 wt% MEA aqueous solution, indicating promising application potential.
✓ 已验证
产品关联
DOI
高影响因子
RSC Advances
·
2017
·Vol. 7
·期 7
·3713-3719
·
IF 3.108
Feng Zhou,Jingjing Zhou,Xuechao Gao,Chunlong Kong,Liang Chen
A postsynthetic covalent strategy involving dual-acyl chloride has been developed to introduce uncoordinated carboxyl groups into amine containing metal–organic frameworks (MOFs). The carboxyl group functionalized MOFs have been characterized by various techniques, including X-ray diffraction patterning, scanning electron microscopy, Fourier transform infrared spectroscopy, nuclear magnetic resonance, thermal gravimetric analysis, and gas adsorption. Results clearly indicated uncoordinated carboxyl groups were successfully grafted to the MIL-101(Cr)–NH2 framework. In addition, most of the amine groups (>80%) were grafted with carboxyl groups, which indicates this method is very effective. The thermal stability and adsorption selectivity of CO2/N2 were substantially enhanced, albeit the BET surface areas and total pore volumes were reduced. These observations could be explained by the effect of elimination of macropores in the framework due to the projecting of new functional groups in pore apertures. Here the successful fabrication of a MOF with uncoordinated carboxyl groups provides the possibility of efficiently modifying other MOFs.
✓ 已验证
DOI
高影响因子
Nanoscale
·
2019
·Vol. 11
·期 16
·7805-7812
·
IF 6.97
Peilong Lu,Denglei Gao,Hongyan He,Qiaoxin Wang,Zhanjun Liu,Sobia Dipazir,Menglei Yuan,Wenyue Zu,Guangjin Zhang
Electrochemically converting carbon dioxide (CO2) to formate offers a promising approach for energy conversion and storage. Bismuth is believed to be one of the promising candidates for CO2 electroreduction, but the poor selectivity and complexity of synthesis limit its real application on a large scale. In this work, a facile one-step-reduction method was developed to prepare a bismuth nanostructure in aqueous solution. Owing to its enhanced reactive sites and exposed crystal plane, the prepared Bi nanostructure exhibits excellent performance for CO2 electroreduction, which reaches the maximum faradaic efficiency for formate as high as 92% at a potential of −0.9 V versus a reversible hydrogen electrode. Additionally, the large current density and remarkable durability also reveal its high intrinsic CO2 electroreduction activity. The density functional theory calculation confirms that the formation of intermediate *OCHO that finally converts to formate is thermodynamically favorable on Bi high-index planes. We anticipate that such a facile synthesis strategy and excellent electrocatalytic performance of the Bi nanostructure will be easy to scale up, realizing its industrialization applications in CO2 electrochemical conversion.
✓ 已验证
DOI
高影响因子
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2013
·
IF 2.206
Yan Wang,Chenghong Zhou,Wucong Wang,Yaping Zhao
A facile and general approach was developed to exfoliate layer materials to produce two-dimensional atomic crystals. A single and few layers of BN, MoS2, and WS2 were obtained via directly exfoliating their powder materials using supercritical CO2 assisted with ultrasound. The effects of supercritical CO2 coupled with ultrasound play a key role in the exfoliation process. The layer numbers and sizes of the BN, MoS2, and WS2 can be easily controlled by adjusting the power and the time of ultrasonication. The AFM images suggest single-layered BN, MoS2, and WS2 were produced, respectively. Their lateral sizes are about 0.5–2 μm, and almost 90% of the BN sheets are less than five layers. The electric diffraction patterns demonstrate that the crystallinities of the produced samples remained the same as that of the raw material during the exfoliating process. This novel technique is cost-effective and scalable, and can be widely used in the production of two-dimensional atomic crystals with high quality.
✓ 已验证
DOI
高影响因子
CARBON
·
2020
·
IF 8.821
Zhichao Miao,Jian Meng,Manfen Liang,Zhenbin Li,Yuzhen Zhao,Fangyuan Wang,Leilei Xu,Jinglin Mu,Shuping Zhuo,Jin Zhou
For the electro-reduction of CO 2 to syngas , the fabrication of electrodes with excellent and adjustable catalytic performance is a critical step. In this work, Ni particles encapsulated in N-doped carbon nanotubes on carbon paper (Ni@N-CNTs/CP) composites were designed and prepared via an in-situ chemical vapor deposition method. As confirmed by different characterization techniques, the Ni@N-CNTs are successfully synthesized, and the surface of the CP is evenly covered by the Ni@N-CNTs. The effects of Ni content and treating temperature on the textural properties of composites are carefully investigated. The Ni@N-CNTs/CP composites are directly employed as the electrode for electro-reduction of CO 2 , and the action mechanisms of the N species, Ni particles, and N-CNTs structure are explored as well. The electrode exhibits excellent catalytic activity and high stability, reaching a specific current of 10 mA cm −2 . The H 2 /CO ratio in the achieved syngas can be tuned in the range of 5/1 to 1/1.5.
✓ 已验证
DOI
高影响因子
DYES AND PIGMENTS
·
2022
·
IF 5.122
Jun Hou,Xiaoqing Xiong,Chengqi Jiao,Xinyao Huang,Deyang Fu,Hongjuan Zhao,Yixuan Li
Supercritical carbon dioxide (scCO 2 ) is commonly used as an excellent solvent in chemical reactions and dyeing fields because of its advantages. In this work, three coumarin and 1,8-naphthalimide fluorescent dyes ( DAMC , NP-NH , and NP-dimethyl ) were successfully constructed on the basis of the Au/titanium dioxide (Au/TiO 2 ) catalytic reduction of nitro in scCO 2 instead of SnCl 2 /hydrochloric acid solution, and their structures were confirmed correctly by mass spectrometry (MS) and nuclear magnetic resonance (NMR). The cleaner synthesis and dyeing polyester fabrics of coumarin derivative ( DAMC ) in the presence or absence of N-methyl-pyrrolidone (NMP) were first studied by employing stepwise and synchronous methods. All results for DAMC indicated that the synchronous synthesis and dyeing method is more beneficial. Here, the synchronous synthesis and dyeing polyester fabrics of 1,8-naphthalimide derivatives ( NP–NH and NP-dimethyl ) in scCO 2 were also investigated. Through the comprehensive analysis of color strength ( K/S ) value and fixation rate, the optimal temperatures and pressures of synthesis and dyeing for NP-NH and NP-dimethyl were obtained in the absence or presence of NMP. The dyed fabrics with NP-NH and NP-dimethyl exhibited yellow or yellowish-brown in daylight and bright fluorescent yellowish-green in ultraviolet light. All results showed that the clean production of fluorescent dyes ( DAMC , NP-NH , and NP-dimethyl ) can be realized by the hydrogenation of nitro with efficient Au/TiO 2 catalyst in scCO 2 , meanwhile, the synchronous synthesis and dyeing method was proposed for the synthesized dyes. The realization of synchronous synthesis and dyeing fabrics for fluorescent dyes in scCO 2 is an effective way to prevent environment pollution brought by the processes of synthesis and dyeing. Thus, the constructing and dyeing strategy of fluorescent dyes will be beneficial to the sustainable development of environment.
✓ 已验证
DOI
高影响因子
JOURNAL OF PETROLEUM SCIENCE AND ENGINEERING
·
2018
·
IF 2.382
Mingchen Ding,Miao Gao,Yefei Wang,Zhengtian Qu,Xu Chen
The effects of fracture density, miscibility and production scheme on CO 2 enhanced oil recovery (EOR) in fractured reservoirs were investigated. A series of CO 2 injection experiments were performed in various lengths of core plugs at both fractured and unfractured condition. Results demonstrate that although presence of fractures dramatically reduces the effectiveness of CO 2 flooding, increasing fracture density clearly benefits its recovery potential. The oil recovery mechanism is mainly recognized to be oil swelling at the beginning of CO 2 continuous injection and gradually turns to extraction of lighter hydrocarbons (C 5 C 30 ) with increased injection time. First-contact miscible flooding is more effective than both multi-contact miscible and immiscible flooding and proves its feasibility when fracture density exceeded 5.0 fractures per meter, with the maximum recovery up to 68.1% of original oil in place (OOIP). CO 2 huff-n-puff is very powerful in recovering the residual oil after CO 2 flooding. Fracture density has no major effect on huff-n-puff performance while at lower fracture-density condition, more cycles are required to reach the ultimate oil recovery. Multi-contact miscible CO 2 huff-n-puff has the greatest potential of EOR ability in fractured reservoirs, which can increase the oil recovery to 86.2% OOIP on the basis of CO 2 flooding test.
✓ 已验证
DOI
高影响因子
Carbon Capture Science & Technology
·
2022
·
IF 0
Weiyang Yuan,Tao Deng,Shuzhen Chen,Yong He,Changlei Qin
High-temperature CO 2 adsorption is an important method in reducing the excessive CO 2 emissions for the mitigation of global climate change. As a potential high-temperature CO 2 sorbent, Li 4 SiO 4 attracted extensive concern due to its high CO 2 capacity with excellent stability. However, gas impurities in industrial flue gas, especially SO 2 affect the CO 2 adsorption process, and the competition between SO 2 and CO 2 during the adsorption process by Li 4 SiO 4 is lack of understanding. This work studied the competitive behavior between carbonation and sulfation through experimental tests, characterizations, and DFT calculations. Results show that carbonation can slightly inhibit the proceeding of sulfation while sulfation almost prevents the occurrence of carbonation for both Li 4 SiO 4 and K-Li 4 SiO 4 . In addition, the doping of K 2 CO 3 in Li 4 SiO 4 is observed to significantly promote both the carbonation and sulfation process. Furthermore, stable adsorption structures of CO 2 and SO 2 on Li 4 SiO 4 were obtained via DFT calculation, which verifies the mutual inhibition between carbonation and sulfation. These results provide a well understanding of the competition between carbonation and sulfation of Li 4 SiO 4 -based sorbents, and are helpful for the design and optimization of CO 2 adsorption process.
✓ 已验证
DOI
Small Methods
·
2026
·
IF 8.7
Weiqian Kong,Pengfei Yan,Song Xu,Zongwei Chen,Xiaoli Zheng,Wei Liu,Wenzhuo Wu,Qingyong Tian,Qun Xu
The two-dimensional (2D) metal-organic frameworks (MOFs) features intrinsic structural peculiarities and high structural design ability, which is considered as a unique platform for prominent electrical and optical applications. A deeper understanding of the electrical and optical properties that are determined by the function of 2D MOFs is crucial for advancing optoelectronic applications. Herein, we propose a novel strategy to enhance light utilization, charge transfer ability and electron dynamics of 2D MOFs by modulating the coordinative environment. The bulk copper tetracyanoquinodimethane (CuTCNQ) is converted into 2D nanosheets (2D CuTCNQ) via the assistance of supercritical carbon dioxide (SC CO 2 ). The solvent effects of SC CO 2 significantly tune the thermodynamical kinetic of bulk CuTCNQ, leading to partial detachment of ligands and the formation of 2D CuTCNQ with unique electron configuration. Simultaneously, 2D CuTCNQ exhibits broadened visible light absorption and accelerated electronic kinetics in comparison with bulk CuTCNQ. Further, the optimized 2D CuTCNQ was employed as a photoanode and it exhibits significantly enhanced photoelectrochemical (PEC) performance, highlighting the potential application in optoelectronic technology. Therefore, such coordinative environment modulation strategy via SC CO 2 opens new avenues to optimize photoelectric properties, and as well as to provide rational design on multifunctional 2D MOFs.
✓ 已验证
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2024
·
IF 8.1
Guocan Shen,Yanbo Liu,Jiajie Ma,Ning Wu,Xionggang Lu,Hongwei Cheng
The application of CeO 2 -δ -molten carbonate (MC) dual-phase membranes is limited by low CO 2 permeation at high temperatures due to poor oxygen ionic conductivity. Ce 1- x Gd x O 2 -δ -MC ( x = 0.00–0.03) dual-phase membranes were designed to investigate the effects of Gd-doping on the ion transport capacity and CO 2 permeability. The introduction of Gd 3+ promotes the conversion of some Ce 4+ to Ce 3+ , initially increasing and then decreasing the Ce 3+ /Ce 4+ ratio. This process increases the oxygen vacancy content, with Ce 0.8 Gd 0.2 O 2- δ showing the highest concentration of oxygen vacancies. At 850 °C, the CO 2 permeation flux of the Ce 0.8 Gd 0.2 O 2- δ -MC membrane is more than twice higher than that of CeO 2- δ -MC, increasing from 0.17 to 0.58 mL min −1 cm −2 . Moreover, the microstructure of the Ce 0.8 Gd 0.2 O 2- δ support is regulated using pore formers of different particle sizes, increasing porosity from 24.3 % to 45.7 %. Consequently, the CO 2 permeation flux of the Ce 0.8 Gd 0.2 O 2- δ -MC dual-phase membrane rises from 0.29 to 0.75 mL min −1 cm −2 at 850 ℃ after optimizing the microstructure of the membrane. Furthermore, the long-term permeation test demonstrates excellent chemical stability of the dual-phase membrane. This study provides feasible modification strategies to enhance CO 2 separation.
✓ 已验证
DOI
高影响因子
ACS Sustainable Chemistry & Engineering
·
2018
·
IF 6.14
Junhui Liu,Anfeng Zhang,Xiao Jiang,Min Liu,Yanwei Sun,Chunshan Song,Xinwen Guo
Conversion of CO2 to sustainable chemical feedstocks and fuels by reacting with renewable hydrogen is considered to be a promising direction in energy research. The selectivity of desired products, such as C2–C4= and C5+, is low over unpromoted iron-based catalysts for CO2 hydrogenation. Therefore, promoters are often used to tailor and optimize the product distribution. In this work, the effect of doping Cu into Fe-based supported catalysts on the catalytic performance for CO2 hydrogenation to hydrocarbons was studied with a particularly focus on the interaction between Fe and Cu. For this purpose, catalysts with different Fe and Cu distribution were prepared by various impregnation methods. It was found that the selectivity of C2–C4= over Cu-promoted catalysts decreased, but a significant improvement was obtained for C5+. This promoting behavior is different from that of other promoters (e.g., K, Mn, Zn, etc.). The secondary conversion of produced olefins on Cu-promoted catalysts, which results from the improvement of olefins adsorption, on Cu-promoted catalysts leads to the decrease of C2–C4= (hydrogenation) but the increase of C5+ (oligomerization). Characterization results demonstrate that the catalytic performance is evidently associated with the strength of the interaction between Fe and Cu in the supported catalysts.
✓ 已验证
DOI
高影响因子
Nano Energy
·
2026
·
IF 16.7
Zihan Ma,Zhong Zhou,Yachao Xu,Xin Chang,Zhaojun Sun,Maoxiang Li,Jianwei Zhang,Ying Wang,Mingyi Zhang
Cu-induced Bi-Cu-S interfaces pin lattice sulfur, suppress photocorrosion, and enable exceptional long-term stability. • Cu 3d-S 3p-Bi 6p hybridization stabilizes CO intermediates and lowers C-C coupling barrier for selective ethylene formation. • The catalyst achieves 100% CO 2 -to-ethylene selectivity, with > 240 h stability and outdoor productivity of 30.0 μmol h −1 g −1 . Photocatalytic reduction of CO 2 to ethylene is an attractive pathway that simultaneously mitigates greenhouse-gas emissions and supplies a value-added C 2 feedstock, but catalyst instability still hinders practical implementation. Here a lattice-pinning strategy is developed in Cu-doped Bi 2 S 3 (Cu-Bi 2 S 3 ), where atomic-scale Bi-Cu-S heterointerfaces and size-mismatched Cu centres immobilize lattice sulfur and sulfur vacancies, thereby raising the barrier for sulfur loss and mitigating photocorrosion. Pinning-driven interfacial reconstruction enhances Cu 3d-S 3p-Bi 6p covalency and reshapes the local electronic structure at Bi-Cu-S sites. These electronic changes stabilize adsorbed CO x intermediates and promote their stepwise hydrogenation to deep C-C coupling products, enabling sustained CO 2 -to-ethylene conversion in sacrificial-agent-free water. Cu-Bi 2 S 3 achieves 100% selective CO 2 -to-ethylene conversion with a rate of about 32.1 μmol g −1 h −1 and retains activity for more than 240 h, giving a stability 16 times that of Bi 2 S 3 when the stability remains at 95%. Under natural sunlight, an ethylene productivity of 30.0 μmol g −1 h −1 , achieved using our self-developed photocatalytic device, and sustained stably over 80 h, demonstrates its practical viability for solar-driven CO 2 -to-ethylene production. This lattice-pinning concept provides a general design principle for long-lived CO 2 photoconversion catalysts. Download: Download high-res image (141KB) Download: Download full-size image
✓ 已验证
DOI
高影响因子