CHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 12.5
Jia Jia,Bo Hu,Lingxi Zhao,Yixin Wang,Yuhan Zhang,Qingyu Li,Mengya Xiao,Hongjun Dong,Chunmei Li
Conventional single-atom catalyst (SAC) design anchors metal atoms within a host matrix to create well-defined metal active sites for enhanced catalytic efficiency. Herein, we engineer a novel SAC featuring Au single atoms (AuSAs), which is synergistically enhanced by the coexistence of Au nanoparticles (AuNPs), transcending the conventional design strategy. The AuSAs are stabilized within the carbon nitride (PCN) skeleton via the formation of an unconventional low-coordination AuN 2 configuration, which is achieved through the coordination of each Au atom with one bridged nitrogen atom and one nitrogen from bipyridine motif. This unique configuration activates the once-inert bridged nitrogen while simultaneously modulates the electronic band structure of PCN. Consequently, the optimal AuSAs-PCN/AuNPs catalyst achieves an average CO production rate 3.59 times higher than that of the pristine PCN in aqueous solution. In triethanolamine solution, the CO and CH 4 production rates reach 1.55 and 1.64 times those of PCN, respectively. This work demonstrates a breakthrough that moves beyond traditional SAC design by creating a low metal-coordination configuration to activate adjacent nonmetallic sites, thereby providing a strategic blueprint for a broad class of high-performance catalysts.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 12.5
Yongkang Cui,Xinyue Chen,Xiaokai Gu,Dongyan Zhao,Yilun Zhou,Zhonghao Wang,Shujuan Wang
Amine-based CO 2 capture is a mature and commercially established technology. High-temperature regeneration causes amine thermal degradation, decreasing capture performance. The thermal stability of four long-chain triamines (N-C-C-C-N-C-C-C-N backbone) was evaluated and the inhibitors were screened. Degradation rates were monitored by gas chromatography and degradation products were characterized using ion chromatography and gas chromatography – mass spectrometry. Quantum chemical calculations and ReaxFF molecular dynamics simulations were employed to elucidate the degradation and inhibition mechanisms. The results indicate that triamines degrade rapidly via a radical-based mechanism. Formate and acetate were identified as the major anionic products, while low-molecular-weight fragments dominated the organic products. Under the tested conditions, the degraded solutions shows slight losses in CO 2 capture performance, but the performance losses were limited. Longer chains decrease the bond dissociation energy of C N and C C bonds and degradation is initiated by homolytic scission of C H and C N bonds, generating radical species and triggering subsequent radical reactions. The addition of 2-ethyl-4-methylimidazole enabled triamines to maintain a residual amine ratio of 80% even after thermal treatment at 423.15 K for 6 days by enhancing local electron density and forming stable non-covalent interactions with the triamines. This work provides insights for the development of high-stability amine-based solutions.
✓ 已验证
产品关联
DOI
高影响因子
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2026
·
IF 3.9
Hongyu Zhang,Kuilin Peng,Min Wang,Guilin Li,Yutong Zhang,Haozhan Chu,Xin Li,Xiangping Zhang,Shaojuan Zeng
The performance of the CO2 reduction reaction (CO2RR) of silver (Ag)-based catalysts is critically influenced by their crystal composition and morphology. Herein, a novel strategy for regulating the crystal composition and morphology of Ag catalysts using ionic liquids (ILs) as electrodeposition solvents was proposed. The results of structure characterization and theoretical calculations demonstrated that the unique dichloroargentate formation, induced by the IL 1-butyl-3-methylimidazolium chloride ([Bmim]Cl), could be superiorly adsorbed on the Ag(111) crystal surface. The dichloroargentate could act as a capping agent and gain electrons rapidly during electrodeposition. This phenomenon led to the formation of dendritic electrodeposited Ag composed with nanoparticles dominated by Ag(111) compared with that prepared without [Bmim]Cl. The electrocatalysts exhibited excellent CO2RR performance because the favorable adsorption of ILs on the surface of electrodeposited Ag increased the CO2 concentration on the electrode surface and stabilized the CO2RR reaction intermediates, which achieved the highest FECO of 99.86% and the jCO of 31.37 mA cm–2. The maximum jCO on this Ag catalyst could reach 83.40 mA cm–2, with the FECO exceeding 95% across a broad 0.4 V potential window. This work provided a feasible strategy for effectively tailoring the crystal composition and morphology of electrocatalysts by regulating the existence of electrodeposited precursors through ILs.
✓ 已验证
产品关联
DOI
高影响因子
Catalysis Science & Technology
·
2026
·
IF 4
Qiao Zeng,Jinshan Chen,Chi Wang,Kai Li,Yi Mei
Photocatalytic reduction of CO2 into CH4 represents a sustainable strategy for carbon recycling, yet achieving efficient multi-electron transfer and selective C–H bond formation remains challenging. Herein, we construct a cooperative multi-interfacial photocatalytic system by integrating copper phthalocyanine (CuPc) and photodeposited Pt nanoparticles onto a TiO2@TPA hybrid. The TiO2@TPA framework, derived from MIL-125 hydrolysis, provides robust Ti–O–C linkages and intrinsic ligand-to-metal charge transfer (LMCT) channels, while CuPc extends visible-light absorption and facilitates interfacial electron delocalization and migration through its π-conjugated macrocycle. Pt nanoparticles exhibit dual functionality—as electron sinks on TiO2 for multi-electron CO2 reduction and as interfacial bridges promoting charge transfer between TiO2 and CuPc. Comprehensive spectroscopic and photoelectrochemical analyses confirm efficient carrier separation, accelerated interfacial charge transfer, and strong electronic coupling at the heterointerfaces. The optimized TiO2@TPA(15Pt,5Cu) catalyst achieves a CH4 evolution rate of 199.2 μmol·g-1·h-1 with 99.9% selectivity, markedly outperforming single-component or monometallic counterparts. In-situ FTIR spectroscopy reveals successive *COOH, *CO, *CHO, and *CH intermediates, validating the multi-step hydrogenation mechanism. This work extends LMCT-based interface engineering toward deep CO2 methanation, offering new insights for the rational design of highly efficient and selective multi-electron photocatalysts.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF RARE EARTHS
·
2026
·
IF 9.6
Huijie Wang,Dedong He,Jichang Lu,Yu Zhang,Jiangping Liu,Xiaohua Cao,Zhizhi Xu,Shaowei Zhang,Dingkai Chen,Yongming Luo
Enhancing the sluggish kinetics of the CO 2 reduction reaction (CO 2 RR) is crucial for the efficient CO 2 -to-CO conversion in solid oxide electrolysis cells. Herein, a dual-exsolution strategy is reported to simultaneously anchor Co and Ni nanoparticles onto distinct La 0.6 Sr 0.4 Co 0.7 Mn 0.3 O 3– δ (LSCM) perovskite phase and Ce 0.9 Ni 0.1 O 2– δ (CNO) fluorite phase, respectively. This design activates both electronic and ionic conduction pathways. The resulting cathode achieves a remarkable CO 2 electrolysis current density of 1.48 A/cm 2 at 1.5 V and 800 °C, representing a 54% enhancement over its non-exsolved counterpart and exhibits stable operation for 100 h. Combined experimental and theoretical analyses reveal that the synergistic Co-Ni bimetallic sites, along with abundant oxygen vacancies, cooperatively enhance CO 2 adsorption and dissociation. Density functional theory calculations provide insights into the intrinsic activity of the newly formed Co@LSCM and Ni@CNO heterointerfaces. This work provides a promising route for designing high-performance composite electrodes via dual-phase engineering.
✓ 已验证
DOI
高影响因子
INORGANIC CHEMISTRY COMMUNICATIONS
·
2026
·
IF 5.9
Yujie Ma,Baowei Shen,Yaping Sun,Lingyu Zhang,Yu Xia,Xing Wang,Yong Liu,Jian Zhao,Yuhua Feng
In nanosynthesis, precise structural tailoring is crucial for modulating the properties of hybrid materials. For photocatalysts, structural configuration of the composed materials is a key factor for improving their efficiency. In this study, the CdS-CeO 2 hybrids in core-satellite and core-shell structures were successfully synthesized via accurate kinetic control in a seed-mediated growth process. Due to the Z -scheme charge transfer mechanism, excellent photocatalytic activity was observed in photocatalytic degradation of methylene blue (MB) and CO 2 reduction reactions (CO 2 RR). Notably, the Janus-type core-satellite structure exhibited significantly higher photocatalytic activity than the core-shell structure. Mechanistic analysis revealed that the spatial separation of the CdS and CeO 2 domains in core-satellite structure led to continuous fast separation and transfer of the photogenerated holes and electrons (h + and e − ) to different exposed domains, whereby can be depleted immediately, resembling the electron sink effect. While in core-shell structure, the transfer of the excited carriers to different domain would inevitably cause charge accumulation at the inner core, which obstruct the further charge separation and transfer. Our study provides an effective general way for promoting the charge separation efficiency in hybrid photocatalyst, which is helpful for the rational design and synthesis of advanced photocatalyst.
✓ 已验证
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2026
·
IF 9.6
Cong Liu,Qing-shan Wang,Heng-fei Cui,Hao-wen Zhu,Ming-yang Liu,Rui-tang Guo
The highly selective generation of products in the photoelectrocatalytic (PEC) CO 2 reduction reaction is significantly hindered by the complex multi-electron transfer process. In this work, we designed and synthesized a Cu 2 O-Au@TiO 2 composite with a unique “core–shell–satellite” architecture via a facile wet-chemical approach. In this architecture, the Au nanocore strengthens visible-light harvesting through localized surface plasmon resonance (SPR) and injects hot electrons into the mesoporous TiO 2 shell, while the outer Cu 2 O selectively exposes highly active (111) facets and establishes low-mismatch interfaces with TiO 2 . This configuration promotes directional charge migration through virus-like synaptic channels, thereby accelerating multi-electron CO 2 reduction. The cooperative mechanism of SPR enhancement, crystallographic facet matching, and dynamic charge transfer enables efficient and selective conversion of CO 2 to C 2 H 4 . Under visible-light irradiation and applied potential, the optimized composite achieves a remarkable C 2 H 4 yield of 174 ± 3.2 μmol·cm −2 ·h −1 with a sustained current density exceeding 75 mA·cm −2 . These findings highlight a rational structural design that synergistically couples plasmonic excitation with interfacial charge management, establishing a promising paradigm for developing high-performance photoelectrocatalytic systems toward solar-driven CO 2 reduction.
✓ 已验证
DOI
PubMed
高影响因子
JOURNAL OF ENVIRONMENTAL MANAGEMENT
·
2026
·
IF 9.2
Changming Zhang,Zhiyan Dong,Lingzhi Huang,Jiangxiu Liang,Xiaochao Zhang,Xiushuai Guan,Jinbo Xue
It is rather important to develop a photocatalyst with high sunlight response, efficient CO 2 adsorption and reduction performance for solar-driven CO 2 reduction. Herein, self-nitrogen-functionalized porous carbon macro-spheres by using melamine as both carbon source and nitrogen source were successfully prepared via suspension polymerization and carbonization strategy, and the effects of different monomer ratios and carbonization temperatures on the photocatalytic reduction of CO 2 were investigated. Our experimental and characterization results demonstrated that N-CS-2 exhibited excellent CO 2 adsorption performance (1.76 mmol g −1 ) and photocatalytic reduction activity (122.49 μmol g −1 ) while the molar percentage of melamine and formaldehyde was 2%, and the CO 2 reduction performance can still remain around 97.6% after ten cycle tests under the same conditions. Furthermore, the photocatalytic performance decreased with the increase of carbonization temperature, and the sample N-CS-600 °C obtained by carbonizing at 600 °C under the optimal amount of melamine showed the highest photocatalytic CO 2 reduction performance, and the pyridine-N and pyrrole-N in the structure of carbon spheres were the main active species and reaction sites for photocatalytic reduction reaction, while the graphite-N acted as an electron transfer channel for reducing the recombination of electron and hole pairs. In addition, the change of carbonization temperature showed little effect on the specific surface area and pore volume of the samples according to the analysis of pore structure, and the pyridine-N and pyrrole-N played an important role in improving the photocatalytic performance under the circumstances. Finally, our results will provide a feasible strategy to synthesize bifunctional metal-free photocatalysts for high-efficiency CO 2 adsorption and photoreduction.
✓ 已验证
DOI
PubMed
高影响因子
Molecular Catalysis
·
2026
·
IF 4.3
Chao Wang,Ting Fan,Shunfang Lv,Tianfu Zhang,Juan Zhang,Jiangang Chen
A series of hydrophobically modified MnO 2 -coated Fe 3 O 4 (Fe@Mn) catalysts were prepared to investigate the effect of the interaction strength between Fe@Mn and hydrophobically modified SiO 2 (SiO 2 -c) on their physicochemical properties, FTS performance and CO 2 selectivity, including granule mixing of Fe@Mn and SiO 2 -c (Fe@Mn+SiO 2 -c (g)), powder mixing of Fe@Mn and SiO 2 -c (Fe@Mn+SiO 2 -c (p)) and core-shell structure of Fe@Mn@SiO 2 -c. The interaction between Fe@Mn and SiO 2 -c evolves and strengthens with the structural progression from physically mixed to core-shell configurations. Contact angle measurements indicate that Fe@Mn@SiO 2 -c exhibits superior hydrophobicity compared to Fe@Mn+SiO 2 -c (g/p). Fe@Mn+SiO 2 -c (g/p) maintains a CO 2 selectivity comparable to that of Fe@Mn, while exhibiting significantly enhanced stability. Although Fe@Mn@SiO 2 -c shows a relatively lower CO conversion, it achieves the lowest CO 2 selectivity alongside a higher selectivity for light olefins. The study reveals that the altered surface microenvironment of Fe@Mn@SiO 2 -c is the key factor in suppressing the water-gas shift (WGS) reaction activity during FTS, thereby reducing CO 2 selectivity. This work elucidates the underlying mechanism by which the interaction mode between the Fe-based catalyst and the hydrophobic material influences the FTS performance, particularly the CO 2 selectivity.
✓ 已验证
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2026
·
IF 9.6
Ran Yang,Yixian Li,Jian Pei,Huaisuo Yao,Jingyang Zhu,Xuehang Wang,Jingxue Sun,Yingxuan Li
Solar-driven photothermal conversion of dilute CO 2 into CH 4 offers a promising route toward carbon-neutral energy cycles, yet designing efficient catalysts for realistic low-concentration streams remains challenging. Herein, a yolk-shell structured nanoreactor composed of homogeneous Ni@NC units (denoted as Ni@NC-9 h) was fabricated via a time-controlled solvothermal and pyrolysis method. This unique architecture acts as a confined nanoreactor that integrates physical and chemical enrichment mechanisms: the internal cavity simultaneously enhances light harvesting and thermal localization via multiple scattering and increases local CO 2 coverage, while the homogeneously distributed nitrogen sites ensure efficient chemical trapping of dilute CO 2 . Under mild conditions (420 nm LED, 180 °C, 12.5% CO 2 , 86.9 mW·cm −2 ), the Ni@NC-9 h catalyst achieves a remarkable CH 4 production rate of 4.33 mmol·g −1 ·h −1 with 94.7% selectivity. Kinetic and in-situ DRIFTS insights uncover a photothermally reduced activation barrier that drives efficient stepwise hydrogenation through *COOH and *CO intermediates. This work provides insights into confinement-enhanced nanoreactor design and establishes a new structural paradigm for the efficient solar-driven upgrading of dilute CO 2 .
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Journal of Environmental Chemical Engineering
·
2026
·
IF 7.5
Shuangshuang Long,Jingwen Wang,Shuqian Meng,Yaxin Liu,Jing Zhang,Zihao Ren,Jiadi Li,Yangyang Xin,Zheng Dong,Baolu Cui,Libing Qian,Wenwu Zhou,Kai Hu,Luyao Wang,Peipei Li,Yaping Zheng,Zhiyuan Yang,Dechao Wang
Porous liquids (PLs), combine the high adsorption capacity of porous solids with the fluidity of liquids, show great promise in selective CO 2 capture. However, current studies on Type I PLs lacks systematic investigations into the regulatory role of porous host particle size and its impact on in-depth analysis of the gas sorption-separation process. Herein, we successfully fabricated PLs by grafting polyether amine oligomer chains onto the surface of size-tailored UiO-66-OH as the porous host, which endow the PLs with good thermal stability, transparency, low viscosity, and promising CO 2 /N 2 separation. UiO-66-OH-PLs were fabricated by grafting polyether amine oligomer steric solvent onto UiO-66-OH via dehydrative condensation. The effect of porous host size on CO 2 separation behavior of UiO-66-OH-PLs and the selective sorption-separation mechanism were systematically investigated using sorption isotherm and kinetic models. UiO-66-OH-PLs exhibit markedly enhanced CO 2 sorption capacity relative to the pure steric solvent, confirming the preservation of accessible cavities in porous hosts. The PLs further exhibit distinct size-dependent physicochemical and sorption properties as decreasing the particle size of UiO-66-OH porous hosts increases oligomer grafting density, reduces bulk viscosity and enhances both CO 2 sorption capacity and CO 2 /N 2 separation selectivity. CO 2 adsorption isotherms are best fitted by the SS-Langmuir-Freundlich model, indicating that CO 2 sorption by UiO-66-OH-PLs is single-component sorption on heterogeneous surfaces, integrating Langmuir monolayer sorption and Freundlich non-ideal sorption characteristics. Kinetic analysis reveals that the optimal pseudo-first-order kinetic model, demonstrating that CO 2 sorption rate is dominated by the sorption-desorption process between adsorbate molecules and adsorbent surface-active sites, rather than intraparticle or liquid film diffusion. This work opens up a promising avenue for the rational design of high-performance PLs that can be tailored to meet the demands of practical industrial chemical separation processes.
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2026
·
IF 9.1
Yuyan Ye,Xiuzheng Deng,Jingshan Fan,Yani Huang,Can Cui,Changhai Liu,Qian Liang
Photocatalytic CO 2 reduction into value-added fuels is an appealing route to store solar energy while mitigating carbon emissions, yet achieving efficient and highly selective hydrocarbon formation in pure water remains challenging. Herein, we report a dopant co-engineering strategy by constructing Ni-doped Bi 2 MoO 6 with abundant oxygen vacancies (Ni x BMO-O V ). An ethylene glycol-mediated synthesis enables vacancy-rich Bi O environments and exposes abundant active sites, thereby strengthening CO 2 adsorption and accelerating interfacial charge transfer to facilitate hydrogenation toward CH 4 . Under simulated solar irradiation using pure H 2 O as the sole proton source, the optimized Ni 0.15 BMO delivers a CH 4 evolution rate of 45.0 μmol·g −1 ·h −1 with an exceptional CH 4 selectivity of 99.1%. Ni incorporation and O V modulate the local electronic structure and charge distribution, thereby affecting the adsorption and activation of CO 2 and intermediates toward the target CH 4 product. This work provides an effective synergistic strategy involving Ni incorporation and oxygen vacancies for regulating electronic structure and reaction pathways toward efficient photocatalytic CO 2 reduction.
✓ 已验证
产品关联
DOI
高影响因子