JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2015
·Vol. 26
·期 10
·7823-7828
·
IF 1.569
Zhang Biao,Ye Feng,Liu Shichao,Liu Qiang,Gao Ye
A simple method, which include cold isostatic pressing and vacuum assisted infiltration, that can significantly improve the filler content, was employed to fabricate Bisphenol-A cyanate ester resin (BADCy)/Ni 0.5 Ti 0.5 NbO 4 composites with high-k and ultra-low-loss. Results show that briquetting pressure and sintering temperature for fabricating Ni 0.5 Ti 0.5 NbO 4 porous preforms have a great influence on the properties of BADCy/Ni 0.5 Ti 0.5 NbO 4 composites. The optimal process for the fabrication of BADCy/Ni 0.5 Ti 0.5 NbO 4 composites is fixing the briquetting pressure at 90 MPa and sintering temperature at 700 °C. The dielectric constant and loss of the composites are 22.79 and 4.17 × 10 −3 at 9041 MHz, respectively. Properties of this kind of composites can meet the requirements for high-k and ultra-low-loss PCB application.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF NANOPARTICLE RESEARCH
·
2015
·Vol. 17
·期 6
·1-8
·
IF 2.184
Du Guangrong,Guo Xueyi,Yang Wenchao,Bi Yujing,Du Rui,Liu Yang,Wang Deyu
In this work, nano -LiMn 0.8 Fe 0.2 PO 4 /C is synthesized via dimethyl sulfoxide-assisted co-precipitation route, and various additives are introduced to disturb the phosphate crystal growth. Among the investigated systems, introducing beta-cyclodextrin and ascorbic acid decreases the surface area of the prepared samples, whereas involving hexadecyltrimethyl ammonium bromide (CTAB) effectively diminishes the particle size of LiMn 0.8 Fe 0.2 PO 4 . Due to the reduced diffusion length and augmented active area, samples from systems containing CTAB exhibited improved electrochemical performance, 155 mAh g −1 at 0.05 C and 120 mAh g −1 at 5 C, relative to the control sample (152 and 114 mAh g −1 at 0.05 and 5 C). Our results indicate that the LiMnPO 4 kinetics could be tailored using appropriate additives.
✓ 已验证
产品关联
DOI
高影响因子
MICROCHIMICA ACTA
·
2015
·Vol. 182
·期 11
·2009-2017
·
IF 3.741
Hao Chenxia,Liu Shaopu,Liang Wanjun,Li Dan,Wang Linlin,He Youqiu
We report on a simple, sensitive and regenerable fluorescent nanoprobe for Zn(II) ion. It is based on the use of glutathione capped CdTe quantum dots (GSH-CdTe Q-dots). The bright fluorescence of these Q-dots is quenched on addition of diethylenetriaminepentaacetic acid (DTPA) due to the binding of DTPA to GSH. If, however, Zn(II) is added, it will bind DTPA and detach it from the surface of the Q-dots, this resulting in the fluorescence recovery. Under optimum conditions, the intensity of the restored fluorescence is proportional to the concentration of Zn(II) in the 0.48 to 90 μmol · L −1 range, with a limit of detection of 0.14 μmol · L −1 . The nanoprobe was applied to the determination of Zn(II) in spiked tap water and river water and gave satisfactory results. The findings were also applied to design a molecular logic gate where DTPA acts as the first input to the system by quenching the fluorescence of the GSH-CdTe Q-dots. Zn(II) acts as the second input and causes the detachment of DTPA from the Q-dots and a restoration of fluorescence. This system therefore represents a new IMP (IMPLICATION) logic gate.
We describe a fluorescent nanoprobe for Zn(II) based on quantum dots, and its use in an IMP molecular logic gate. The nanoprobe was successfully applied to the determination of Zn(II) in spiked tap water and river water.
✓ 已验证
产品关联
DOI
高影响因子
CELLULOSE
·
2015
·Vol. 22
·期 4
·2717-2727
·
IF 3.573
Li Mufang,Wu Zhihong,Luo Mengying,Wang Wenwen,Chang Kangqi,Liu Ke,Liu Qiongzhen,Xia Ming,Wang Dong
Thin film composite (TFC) membrane is one of the most promising technologies in the purification field. In this study, a novel highly hydrophilic and anti-fouling cellulose TFC membrane was prepared based on the hierarchical poly(vinyl alcohol- co -ethylene) (PVA- co -PE) nanofiber substrate. The morphology and hydrophilicity of the hierarchical PVA- co -PE nanofiber substrate and the cellulose TFC membrane were analyzed by SEM, FESEM, and contact angle goniometry. To optimize the performance of cellulose TFC membrane, the effects of coagulation bath, cellulose concentration and thickness of cellulose layer on the filtration efficiency, water flux as well as the mechanical property were studied. The anti-fouling property of the cellulose TFC membrane was analyzed by testing the change in the flux of membrane during repeated bovine serum albumin (BSA) filtrating and fouling process. The results show that the filtration efficiency of cellulose TFC membrane to BSA with the diameter of 2–10 nm could be above 97 %. Due to the hydrophilicity of the top cellulose layer, the cellulose TFC membrane exhibits excellent anti-fouling property by showing the 100 % flux recovery ratio.
✓ 已验证
产品关联
DOI
高影响因子
Science China-Chemistry
·
2015
·Vol. 58
·期 6
·1021-1026
·
IF 1.695
Chai Chunpeng,Yin Fangfang,Li Guoping,Luo Yunjun
The effects of mesogen-jacketed liquid crystalline polymer poly(dipropyl vinylterephthalate) (PDPVT) on the mechanical and thermal properties of diglycidyl ether of bisphenol-A (DGEBA) epoxy resin were investigated by impact test, tensile test and thermogravimetric analysis (TGA). The mechanism underlying the enhancement of mechanical properties of epoxy resin was studied using 1D wide-angle X-ray diffraction (WAXD) and scanning electron microscope (SEM). It was found that the mechanical properties of 1 wt%–5 wt% PDPVT/DGEBA composites were significantly improved compared to neat epoxy resin. Especially, the epoxy resin with 3 wt% PDPVT had the greatest increase in mechanical properties, with the impact strength, tensile strength and elongation while breaking increased by 87%, 59% and 174%, respectively. The increased mechanical strength was due to the fact that PDPVT maintained liquid crystalline phase in cured PDPVT/DGEBA composites, which would blunt the crack tip and prevent crack propagation. Moreover, PDPVT had slight effect on the thermal stability properties of epoxy resin.
✓ 已验证
产品关联
DOI
高影响因子
CHINESE JOURNAL OF POLYMER SCIENCE
·
2013
·Vol. 31
·期 4
·691-701
·
IF 1.27
Tan Lin,Xing Jin-xing,Cao Fu-hu,Chen Li-juan,Zhang Chong,Shi Rong-hua,Wang Yan-mei
A series of double-hydrophilic double-grafted PMA- g -PEG/PDMA copolymers, which contained poly(methacrylate) (PMA) as backbone, poly(ethylene glycol) (PEG) and poly( N,N -dimethylacrylamide) (PDMA) as side chains synthesized successfully by using reversible addition-fragmentation chain transfer (RAFT) polymerization and atom transfer radical polymerization (ATRP), were used as physical coatings for the evaluation of protein-resistant properties by capillary electrophoresis (CE). Electroosmotic flow (EOF) measurement results showed that the PMA- g -PEG/PDMA copolymer coated capillaries could suppress electroosmotic mobility in a wide pH range (pH = 2.8–9.8) and EOF mobility decreased with the increase of copolymer molecular mass and PDMA content. At the same time, protein recovery, theoretical plate number of separation and repeatability of migration time demonstrated that antifouling efficiency was improved with the increase of molecular mass and PEG content.
✓ 已验证
产品关联
DOI
高影响因子
APPLIED BIOCHEMISTRY AND BIOTECHNOLOGY
·
2013
·Vol. 169
·期 6
·1811-1821
·
IF 1.893
Wang Ting,Li Bin,Lin Li
A novel functional material of β -cyclodextrin ( β -CD) grafting cellulose beads containing immobilized silver nanoparticles (AgNPs) is presented in this paper. The morphology was characterized by scanning electron microscopy, energy-dispersive X-ray, and X-ray photoelectron spectroscopy. Phenolphthalein probe molecule technique was used to detect the activity of the grafting β -CD, and the results demonstrated that the deposition of AgNPs had no influence on its encapsulation ability. Acid resistance of the AgNPs on the bead material was studied by atomic absorption spectrometry. The stability of the AgNPs was enhanced due to the grafting of β -CD. Tube dilution method was applied to study the bacteriostatic effect, and the minimal inhibitory doses of the novel material against Escherichia coli and Staphylococcus aureus were 12.5 and 25 mg, respectively. The minimal bactericidal doses for the two bacteria were 25 and 25 mg, respectively.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
COLLOID AND POLYMER SCIENCE
·
2013
·Vol. 291
·期 7
·1573-1580
·
IF 2.161
Zhao Xuejuan,Zhang Jun,Chen Shuangjun,Wang Xiaolin,Wang Jianxin
The in situ polymerization of poly(ethylene glycol) methyl ether methacrylate (PEGMA) in poly(vinylidene fluoride) (PVDF) solution was carried out to prepare hydrophilic PVDF/PPEGMA blends. Based on T
g data, the system displayed some miscibility at low PPEGMA content because there were some interactions between PVDF and PPEGMA, as illustrated by Fourier transform infrared spectroscopy analysis, while the miscibility disappeared at high PPEGMA content. The β phase was the predominant crystalline phase of PVDF in the in situ blends, which was independent on PPEGMA content. However, the addition of PPEGMA could change the unit cell structure in the direction of the a -axis of β phase. The degree of crystallinity of the in situ blends calculated by wide-angle X-ray diffraction and differential scanning calorimetry displayed different tendencies with PPEGMA content. The scanning electron microscopy showed that the “spherulites” size increased with the increase in PPEGMA content, since the “spherulites” were comprised of not only crystalline PVDF but also amorphous PVDF and PPEGMA. In addition, the in situ blend had a great improvement in the hydrophilicity; specifically, its water contact angle was down to 26° when the PPEGMA content only increased to 26.9 wt.%.
✓ 已验证
产品关联
DOI
高影响因子
CHROMATOGRAPHIA
·
2012
·Vol. 75
·期 21
·1287-1293
·
IF 1.195
Wang Shuping,Li Xinchun,Yang Jianping,Yang Xiujuan,Hou Fenghua,Chen Zuanguang
In clinical medicine, urine creatinine concentration is an important marker in the evaluation of renal function and muscular dysfunctions. Herein, we reported a novel method for rapid determination of creatinine in urine by microchip electrophoresis with light-emitting diode induced fluorescence detection. Creatinine was derivatized by fluorescein isothiocyanate, and then quantitatively detected by the developed microchip LED induced fluorescence detection system. The excitation and emission wavelengths were 490 and 523 nm, respectively. The urine samples were analyzed after centrifuge and filtration. A baseline separation was obtained in <30 s using 10 mM borate buffer (pH 9.0, containing 45 mM sodium dodecylsulfate), with separation voltage of 1.5 kV. Good linearity was obtained ( r
2 = 0.9978) in the concentration range of 10.0–2.00 × 10 3 μM, and the limit of detection was 2.87 μM ( S/N = 3). The recovery was 96.0–107 %, and the interday precision was <4.5 % ( n = 6). To validate assay results, we compared the present method with the Jaffe’s colorimetric assay by measuring real urine samples. The method was reliable, sensitive, high-speed, low-cost and suitable for the routine analysis of creatinine in biofluids.
✓ 已验证
产品关联
DOI
高影响因子
COLLOID AND POLYMER SCIENCE
·
2012
·Vol. 290
·期 17
·1825-1831
·
IF 2.331
Li Guang Hua,Yang Ping Ping,Gao Zhen Sheng,Zhu Yuan Qin
Poly(acrylic acid- b -styrene) (PAA- b -PS) amphiphilic block copolymers were synthesized by consecutive telomerization of tert -butyl acrylate, atom transfer radical polymerization (ATRP) of styrene, and hydrolysis. The resulting block copolymers were characterized by 1 H NMR and GPC. These amphiphilic block copolymeric micelles were prepared by dialysis against water. Transmission electron micrograph (TEM) and laser particle sizer measurements were used to determine the morphology and size of these micelles. The results showed that these amphiphilic block copolymers formed spherical micelles with average size of 140–190 nm. The critical micelle concentration (CMC) and the kinetic stability of these micelles were investigated by fluorescence technique, using pyrene as a fluorescence probe. The observed CMC value was in the range of 0.075–0.351 mg/L. Kinetic stability studies showed that the stability of micelles increased with the decrease of the pH value of the solution.
✓ 已验证
产品关联
DOI
高影响因子
Plasmonics
·
2015
·Vol. 11
·期 2
·619-625
·
IF 2.238
Luo Lin-Bao,Zheng Kun,Ge Cai-Wang,Zou Yi-Feng,Lu Rui,Wang Yuan,Wang Dan-Dan,Zhang Teng-Fei,Liang Feng-Xia
Light manipulation is vitally important for one-dimensional semiconductor nanostructure-based photodetectors which have great potential in future optoelectronic circuits, imaging technique, and light-wave communication. In this paper, we reported a plasmonic gold nanoparticle (AuNP)-decorated nano-photodetector for green light sensing. It is found that the as-fabricated device exhibits obvious increase in light absorption in the range from 400 to 550 nm, after functionalization of plasmonic AuNPs. Further device performance analysis reveals that the photocurrent of the plasmonic photodetector was increased by more than sevenfold, compared with that without coating. What is more, both responsivity and detectivity are found to increase as well. According to theoretical simulation based on the finite element method (FEM), the observed enhancement in device performance can be attributed to the surface plasmon-induced direct electron injection from the metal nanoparticles to the semiconductor nanostructures.
✓ 已验证
DOI
高影响因子
JOURNAL OF SOL-GEL SCIENCE AND TECHNOLOGY
·
2014
·Vol. 74
·期 1
·161-167
·
IF 1.547
Lan Yuanfei,Jin Miaomiao,Luo Yunjun
Abstract A novel graphene aerogel (GA)/ferric oxide (Fe 2 O 3 )/ammonium perchlorate (AP) nanostructured energetic composite was prepared by a facile sol–gel method and supercritical carbon dioxide drying technique. In this study, the morphology and structure of the obtained GA/Fe 2 O 3 /AP nanostructured energetic composite were characterized by scanning electron microscopy, nitrogen sorption tests and X-ray diffraction. The thermal decomposition characteristic was investigated by thermogravimetry and differential scanning calorimetry. The results demonstrated that Fe 2 O 3 and AP dispersed in the as-prepared energetic composite at nanometer, showing promising catalytic effects for the thermal decomposition of AP. For the nanostructured energetic composite, GA and Fe 2 O 3 played a catalytic role in the thermal decomposition of AP. Only one decomposition step was observed, instead of two, which was common in previous report. The decomposition temperature of the nanocomposite was obviously decreased as well. Moreover, the total heat release increased significantly. The experimental results showed that the as-prepared GA/Fe 2 O 3 /AP nanostructured energetic composite could be a promising candidate material for the solid propellants. Graphical Abstract A novel GA/Fe 2 O 3 /AP nanostructured energetic composite was prepared by a facile sol–gel method and supercritical carbon dioxide drying technique. Fe 2 O 3 and AP nanoparticles are added and trapped in the porous three-dimensional networks of GA. The decomposition temperature of the nanocomposite was obviously decreased, and the total heat release increased significantly. Moreover, the thermal decomposition mechanism of the nanocomposite was analyzed.
✓ 已验证
DOI
高影响因子