INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2017
·
IF 2.843
Qilei Yang,Ang Cao,Na Kang,Hongyan Ning,Jiaming Wang,Zhao-Tie Liu,Yuan Liu
The catalytic performance of Cu–Co/Al2O3 in the slurry reactor for direct ethanol synthesis from syngas was investigated. The reduced catalyst and catalyst reacted for 100, 300, 500, and 750 h were characterized by using XRD, TEM, EDS, BET, and ICP-MS techniques. Compared with that in the fixed-bed reactor, the catalyst in the slurry reactor exhibited higher selectivity to ethanol, which was above 70 wt % in the total alcohols. The structure variation of the bimetallic Cu–Co with reaction time is that CuCo2O4 was transformed into Cu–Co alloy after reduction, and Cu–Co alloy was decomposed into Cu and Co after reaction for 100 h. After reaction for 300 h, Co2C started to generate and Cu@Co@Co2C was formed as reacted for 500 h. All of Cu–Co alloy, Cu@Co, and Cu@Co@Co2C are highly selective to ethanol, which was maintained for 750 h. Meanwhile, the slurry solvent of PEG-400 is another reason for the high ethanol selectivity.
✓ 已验证
产品关联
DOI
高影响因子
Sustainable Energy Technologies and Assessments
·
2024
·
IF 7.1
Linhao Wang,Dongqiang Lei,Yue Lv,Ruishen Guo,Ying Wu,Zhifeng Wang
In the study, a novel photodeposition one-step method for preparing Cu/TiO 2 photothermal catalysis was proposed to catalyze hydrogen production from glycerol. The biomass glycerol was used as a sacrificial agent to provide electrons for Cu 2+ loading during the catalyst preparation stage, and the remaining biomass glycerol was used directly as a reactant for photothermal-catalyzed hydrogen production. The catalysts were characterized using XRD, SEM, and TEM to obtain their phases and structures. The Cu/TiO 2 photodeposition process evaluation method based on image analysis and processing, and its experimental platform were established. The influence of parameters such as irradiation intensity, temperature, and catalyst concentration on the loading rate of photodeposited Cu 2+ was analyzed. The results demonstrated that enhancing the irradiation intensity, increasing the temperature, and decreasing the catalyst concentration can increase the loading rate of Cu. The Cu/TiO 2 photothermal catalyst prepared by this method showed a hydrogen production rate 1.6 times higher than that of the deposition and precipitation method under the same reaction conditions, which proved that the catalyst had a high photothermal catalysis hydrogen production activity. The hydrogen production rate at an irradiation intensity of 250 mW/cm 2 was 628.16 μmol/(g·h), which was 1.9 times that at an irradiation intensity of 100 mW/cm 2 . Both elevated temperature and increased irradiation intensity can significantly improve the photothermal catalysis glycerol hydrogen production activity.
✓ 已验证
产品关联
DOI
高影响因子
Nanoscale
·
2024
·
IF 5.8
Xi Luo,Han-Yao Sun,Shang-Yu Lu,Yan Zhou,Zi-Qing Xu,Nan Zhong,Yi-Shi Lu,Shou-Ju Wang,Hai-Bin Shi,Wei Tian
Microwave ablation (MWA) is recognized as a novel treatment modality that can kill tumor cells by heating the ions and polar molecules in these cells through high-speed rotation and friction. However, the size and location of the tumor affect the effective ablation range of microwave hyperthermia, resulting in residual tumor tissue and a high recurrence rate. Due to their tunable porous structure and high specific surface area, metal–organic frameworks (MOFs) can serve as microwave sensitizers, promoting microwave energy conversion owing to ion collisions in the porous structure of the MOFs. Moreover, iron-based compounds are known to possess peroxidase-like catalytic activity. Therefore, Fe-doped Cu bimetallic MOFs (FCMs) were prepared through a hydrothermal process. These FCM nanoparticles not only increased the efficiency of microwave-thermal energy conversion as microwave sensitizers but also promoted the generation of reactive oxygen species (ROS) by consuming glutathione (GSH) and promoted the Fenton reaction to enhance microwave dynamic therapy (MDT). The in vitro and in vivo results showed that the combination of MWA and MDT treatment effectively destroyed tumor tissues via microwave irradiation without inducing significant side effects on normal tissues. This study provides a new approach for the combined application of MOFs and microwave ablation, demonstrating excellent potential for future applications.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
APPLIED CATALYSIS B-ENVIRONMENTAL
·
2024
·
IF 20.2
Yegang Xia,Xingwen Cha,Xing Yan,Xueying Wang,Yanmei Cai,Kok Bing Tan,Jinxin He,Ting Qiu,Dongren Cai,Guowu Zhan
Regulation of abundant Cu-ZnO interfaces in Cu/ZnO catalysts is critical to the thermal hydrogenation of CO 2 to methanol. Herein, Cu-ZnO interfaces were precisely regulated by depositing thin ZnO films on copper phyllosilicates (CuSiO 3 ) through atomic layer deposition (ALD) to prepare Cu/ZnO/SiO 2 composite catalysts (denoted as x ZnO/CuSiO 3 , x is the number of ALD cycles) for CO 2 hydrogenation to methanol. Interestingly, 5ZnO/CuSiO 3 exhibited much higher methanol selectivity of 68.1 % and methanol space-time yield (STY MeOH ) of 0.39 g MeOH h −1 g cat −1 toward CO 2 hydrogenation at 275 ℃ and 3 MPa, as compared to the pristine CuSiO 3 (38.1 % and 0.24 g MeOH h −1 g cat −1 ), suggesting the significant role of Cu-ZnO interfaces. Compared to ZnO/CuSiO 3 (IM) prepared by the conventional impregnation method, 5ZnO/CuSiO 3 possessed much higher CO 2 conversion (13.8 % vs. 10.1 %) and methanol selectivity (68.1 % vs. 56.2 %). Furthermore, the catalytic activities of the prepared Cu/ZnO catalysts can be effectively regulated by changing the thickness of ZnO-ALD films, in which 5ZnO/CuSiO 3 showed the best catalytic activity. Various characterization methods were applied to demonstrate that ALD-ZnO was evenly laid flat on the surface of CuSiO 3 to construct abundant Cu-ZnO interfaces during the H 2 reduction treatment, which facilitated the dissociated activation of CO 2 and formation of CH 3 O* reaction intermediate and simultaneously inhibited the generation of CO byproduct. In addition, the density functional theory (DFT) calculations revealed the stronger interaction between Cu and ZnO over 5ZnO/CuSiO 3 , which implied more Cu-ZnO interfaces were generated for methanol production. Accordingly, this study verifies the significance of Cu-ZnO interfaces for CO 2 hydrogenation to methanol and provides a facile method to regulate Cu-ZnO interfaces by depositing ALD-ZnO films on the copper phyllosilicate precursor.
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2024
·
IF 8.1
Xinyue Zhang,Yichu Ma,Hengqiang Yang,Chenglong Shi,Qingjun Zhou
The development of electrode materials with high catalytic activity at intermediate temperature (600–800 °C) is essential for improving the output performance of solid oxide fuel cells. Here, we report low cobalt-based Sr 2 Fe 1.5-3x Ni x Cu x Co x Mo 0.5 O 6 (x = 0.05, 0.1, 0.15, SF x NCCM) as symmetrical electrode materials. With effective control of the anode side, Fe–Co–Ni–Cu nanoparticles precipitate from and are uniformly distributed across the parent surface, enhancing the electrode material's electrochemical performance. The output performance of single cell is better than that of Sr 2 Fe 1.5 Mo 0.5 O 6-δ symmetric cell without nanoparticle modification. In addition, the maximum power densities of the single cell with ∼300 μm thick Ce 0.9 Gd 0.1 O 1.95 as electrolyte and SF x NCCM as symmetrical electrode material reached 750, 620 and 621 mW cm −2 at 800 °C, respectively. The reversibility of nanoparticles exsolution and phase structure transformation are confirmed. The in-situ self-assembled electrode materials reported in this study provide a foundation for future research on fuel cell electrodes.
✓ 已验证
产品关联
DOI
高影响因子
GREEN CHEMISTRY
·
2024
·Vol. 26
·期 10
·6131-6138
·
IF 9.3
Yan Wang,Xuan Wang,Yonghao Dong,Mingli Peng,Lina Guo,Mengyao Cui,Yuan He,Jiabao Yi,Huijun Ma,Huan Zhang,Haiming Fan
The selective oxidation of alcohols has drawn significant attention in heterogeneous catalysis with the increasing use of Pickering interfacial catalysis (PIC) for green transformations of alcohols. However, it is still highly desirable to design and develop a solid catalyst with easy separation and recycling, made from abundant resources through a simple synthesis route, for the selective oxidation of alcohols. In this study, ferrite nanoparticles, synthesized via a hydrothermal process, were employed to act as a stabilizer and catalyst in PIC for the oxidation of benzyl alcohol using H2O2. The ferrite nanoparticles exhibited higher catalytic performance in PIC than in acetonitrile. The turnover number (TON) of the nanocatalyst in PIC was found to be 1.5–4 times higher than that in acetonitrile, and the reaction constant in PIC (kPIC = 0.712 h−1) was almost twice that in acetonitrile (kCH3CN = 0.310 h−1) for MnFe2O4 nanoparticles. Moreover, other alcohols could also be oxidized with moderately high conversion and selectivity in PIC. Significantly, the ferrite nanocatalyst could be easily separated from PIC using a magnet for reuse, achieving 88% BzOH conversion after five cycles. The use of hazardous organic solvents was avoided in PIC, making it a more advanced, green and sustainable reaction system.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF ELECTROANALYTICAL CHEMISTRY
·
2024
·
IF 4.1
Yu-Hua Xiao,Qiu-Yu Huang,Jian Wang,Xin-Ran Li,Ze-Jie Zhu,Qin-Hao Zhang,Fa-He Cao
Localized and interface pH values are important parameters for studying the corrosion progress and complex interface reactions. Although commercial glass pH sensors have been widely used to measure solution pH value due to their advantages of long stability and high sensitivity, they were unable to determine the interface and microregion pH value for their difficulty in miniaturization. In this work, an all-solid-state pH micro-sensor with strong adhesion strength was in-situ fabricated on diameter 15 μm tungsten ultramicroelectrode (UME) using constant current anodizing. The pH micro-sensor showed good linear response (R 2 = 0.999), excellent sensitivity (with a slope of −53.8 mV/pH), quick response (<0.1 s), long lifetime (>44 days) and great anti-interference ability to most of the ions in marine (selectivity coefficients pK ij > 7), such as SO 4 2− , Cl − , NO 3 − , K + , Mg 2+ and Fe 2+ . Then, the pH micro-sensor, combined with the potentiometric mode of SECM, was further employed to explore the localized pH value distribution during the galvanic corrosion of Fe-Cu couple in 0.1 M NaCl solution. To further verify the anti-interference ability of pH micro-sensor, potentiometric SECM experiment was also conducted in artificial seawater. Results showed that both acidic sites and alkalizing sites appeared on the Fe surface, while homogeneous alkalization took place overall Cu surface. This was consistent with the SVET results that anodic and cathodic areas existed simultaneously on Fe surface. Thus, it could be concluded that local corrosion occurred on Fe surface and only part of the Fe surface acted as the anodic even under galvanic effect. However, Cu acted as cathode with the homogeneously distributing cathodic current on the whole surface during the galvanic corrosion.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Water Process Engineering
·
2025
·
IF 6.7
Min Zhou,Dan Zheng,Kun Yang,Lifang Hu,Zhongbiao Zhang
Fenton catalytic oxidation is a prevalent advanced oxidation technology that can be integrated with photocatalysis and thermal catalysis to enhance the degradation of antibiotic wastewater. Zeolites, a distinctive class of crystalline material, are extensively employed in Fenton-like catalytic oxidation due to their robust structure and exceptional catalytic efficacy. In this study, we constructed a novel Cu/Ce-X catalyst via an ion exchange process based on a Na-X zeolite matrix. The crystal phases, framework structures, elemental compositions, specific surface areas, and photothermal catalytic activity of the composite catalyst were characterized systematically. The removal of tetracycline hydrochloride (TCH) was 87.69 % in the photothermal Fenton-like degradation, and the apparent first-order kinetics rate constant was 13.6 times, 6.52 times, and 1.72 times greater than those of the Fenton-like, photo Fenton-like, and thermal Fenton-like systems, respectively. The adaptability, reusability, reaction mechanisms, and degradation pathways of the fabricated catalysts for the removal of TCH were investigated. The experimental and characterization results demonstrate that the redox cycling of Cu + /Cu 2+ and Ce 3+ /Ce 4+ was enhanced through photogenerated electrons and thermal effects in the catalytic degradation process. The primary active species generated in the photothermal Fenton-like system is ·OH. The findings of this research provide a viable strategy for the treatment and remediation of water pollution.
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2024
·
IF 8.1
Donggang Wang,Tong Zheng,Haibin Sun,Xiaoyu Zhang,Xue Guo,Qiangqiang Hu,Yurun Feng
Grain boundary resistance is one of the main factors inhibiting the electrical properties of BaZr 0.1 Ce 0.7 Y 0.2 O 3-δ (BZCY) proton conduction electrolytes for solid oxide fuel cells (SOFCs). The Cu-doping strategy is applied to improve the electrical performance of grain boundary by promoting the grain growth and reducing the grain boundary blocking effect. For BaZr 0.1 Ce 0.7 Y 0.2-x Cu x O 3-δ (BZCYCu x , x = 0, 0.025, 0.050, 0.075, 0.100), the largest average grain size is 11.64 μm, which is approximately 5 times that of the BZCY electrolyte without Cu doping (2.13 μm). The optimized electrical performance is 1.64 × 10 −2 S cm −1 at 700 °C in moist air, which is twice that of BZCY. This is mainly attributed to the enhanced grain boundary conductivity by appropriate Cu doping, while BZCYCu 0.075 has the highest w / d g (0.733) and a relative low Δ φ (0) (0.201). The anode-supported cell shows a peak power density of 810 mW cm −2 at 700 °C in moist H 2 (as fuels) and ambient air (as oxidants).
✓ 已验证
产品关联
DOI
高影响因子
FOOD CHEMISTRY
·
2024
·
IF 8.5
Ke Deng,Haixia Hu,Yi Li,Xue Li,Huiling Deng,Ya Chen,Xiao Yang,Lijun Wang,Xianggui Chen
In this study, a dual-mode colorimetric/CL nanosensor was developed for glyphosate detection based on the specific inhibition of Fe 3 O 4 @Cu peroxidase-like activity. Synthesized Fe 3 O 4 @Cu exhibited high levels of peroxidase-like activity that triggered the oxidation of luminol/3,3′,5,5′-tetramethyl benzidine dihydrochloride (TMB) to excited-state 3-aminophthalic acid/blue oxTMB, thereby delivering a CL signal/visible colorimetric signal, however, the presence of glyphosate inhibited this activity, resulting in a decrease in signal strength. In-depth investigation revealed that this inhibitory mechanism occurs via two pathways: one in which glyphosate chelates with Fe(III)/Cu(II) and occupy the catalytical active sites of Fe 3 O 4 @Cu, thereby decreasing the generation of OH, and another in which glyphosate competes with TMB to consume generated OH, thus reducing the oxidation of TMB. This mechanism formed the basis of our novel dual-mode colorimetric/CL glyphosate nanosensor, which achieved limits of detection (LODs) of 0.086 µg/mL and 0.019 µg/mL in tests, thus demonstrating its significant potential for on-site glyphosate monitoring.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
FUEL
·
2024
·
IF 6.7
Jing Jiang,Yao Tian,Jiayi Zhang,Chenghui Zhang,Lunhong Ai
Development of multifunctional non-noble electrocatalysts for seawater electrolysis is imperative but still challenging for scale-up hydrogen production to avoid harmful chlorine chemistry. Herein, the metallic Cu-incorporated NiFe layered double hydroxide (LDH) nanosheets are prepared by a facile consecutive corrosion strategy using iron foam (IF) as a reactive substrate, which enable the corrosion-resistant and chlorine-free seawater electrolysis combined with anodic sulfion oxidation for energy-efficient hydrogen production at ultralow electricity consumption. The NiFe-LDH/Cu-IF exhibits excellent electrocatalytic activities for hydrogen evolution reaction (HER) and sulfion oxidation reaction (SOR), achieving low potentials of 0.203 and 0.310 V (vs RHE) at 100 mA cm −2 in alkaline seawater, respectively. The assembled hybrid HER||SOR seawater electrolyzer realizes the ultra-low cell voltage of 0.619 V and power consumption of 1.48 kWh/m 3 H 2 at 50 mA cm −2 , cutting energy consumption over 67 % compared to conventional seawater electrolysis.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY
·
2024
·
IF 11.2
Tian Yuan,Yong Wang,Yiming Zhou,Aijia Zhang,Jie Meng,Ling Li,Wenming Zhang
Highly sensitive sensors with extensive applications are extremely desired in the next-generation wearable electronics for human motion monitoring, human-machine interface and intelligent robotics, while single-functional pressure sensors cannot fulfill the growing demands of modern technological advances. Herein, an all-fabric and multilayered piezoresistive sensor based on conductive metal-organic framework/layered double hydroxide (cMOF/LDH) hetero-nanoforest is demonstrated to achieve multiple applications including pulse detection, joint motion detection, sound detection and information transmission. Benefiting from the synergism of cMOF/LDH hetero-nanoforest and multilayered structure, the sensor exhibits a high sensitivity (1.61×10 9 kPa −1 ) over a broad pressure range (0-100 kPa), a fast response/recovery time (71 ms/71 ms) and a low detection limit (18 Pa), as well as reliable dynamic stability (8000 cycles). It is gratifying to note that the introduction of cMOFs endows the sensor with the potential to detect the concentration of NH 3 (1-100 ppm) and sunlight intensity (10-100 mW cm −2 ). This work shows great potential in multifunctional sensing, which enlightens a strategy for advancing the development process of highly sensitive intelligent wearable devices.
✓ 已验证
产品关联
DOI
高影响因子