Polymers
·
2022
·Vol. 14
·期 24
·5417
·
IF 4.967
Shaoju Jian,Yuhuang Chen,Fengshuo Shi,Yifei Liu,Wenlong Jiang,Jiapeng Hu,Xiaoshuai Han,Shaohua Jiang,Weisen Yang
The occurrence of fluoride contamination in drinking water has gained substantial concern owing to its serious threat to human health. Traditional adsorbents have shortcomings such as low adsorption capacity and poor selectivity, so it is urgent to develop new adsorbents with high adsorption capacity, renewable and no secondary pollution. In this work, magnetic electrospun La-Mn-Fe tri-metal oxide nanofibers (LMF NFs) for fluoride recovery were developed via electrospinning and heat treatment, and its defluoridation property was evaluated in batch trials. Modern analytical tools (SEM, BET, XRD, FTIR) were adopted to characterize the properties of the optimized adsorbent, i.e., LMF11 NFs with a La:Mn molar ratio of 1:1. The surface area calculated via BET method and pHpzcassessed using pH drift method of LMF11 NFs were 55.81 m2g−1and 6.47, respectively. The results indicated that the adsorption amount was highly dependent on the pH of the solution, and reached the highest value at pH = 3. The kinetic behavior of defluoridation on LMF11 NFs was dominated by the PSO model with the highest fitted determination coefficients of 0.9999. Compared with the other three isotherm models, the Langmuir model described defluoridation characteristics well with larger correlation coefficients of 0.9997, 0.9990, 0.9987 and 0.9976 at 15 °C, 25 °C, 35 °C and 45 °C, respectively. The optimized LMF11 NFs exhibited superior monolayer defluoridation capacities for 173.30–199.60 mg F−/g at pH 3 at 15–45 °C according to the Langmuir isotherm model. A thermodynamic study proved that the defluoridation by LMF11 NFs is a spontaneous, endothermic along with entropy increase process. In addition, the LMF11 NFs still showed high defluoridation performance after three reused cycles. These findings unveil that the synthesized LMF11 NFs adsorbent is a good adsorbent for fluoride remediation from wastewater owing to its low cost, high defluoridation performance and easy operation.Keywords:La-Mn-Fe tri-metal oxides nanofibers;defluoridation;electrospinning;kinetics;wastewater treatment
✓ 已验证
DOI
高影响因子
DALTON TRANSACTIONS
·
2020
·Vol. 49
·期 20
·6764-6775
·
IF 4.174
Xuerui Yi,Xiaobo He,Fengxiang Yin,Biaohua Chen,Guoru Li,Huaqiang Yin
Developing earth-abundant highly efficient catalysts for the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) is indispensable for the widespread implementation of electrochemical water splitting to store renewable energy. Herein, amorphous bimetallic selenide (Ni–Fe–Se) hollow nanospheres electrodeposited on nickel foam (Ni–Fe–Se/NF) are developed as a bifunctional catalyst for the HER and OER. The HER and OER bifunctional activity of Ni–Fe–Se/NF outperforms those of monometallic Ni–Se/NF and Fe–Se/NF owing to the synergy of Ni and Fe in Ni–Fe–Se/NF. Moreover, the amorphous hollow spherical morphology of Ni–Fe–Se/NF increases the active site density and facilitates the mass transfer of electrolytes and H2/O2 products. Ni–Fe–Se/NF drives a current density of 10 mA cm−2 with an overpotential of ∼85 mV for the HER and 100 mA cm−2 with an overpotential of ∼222 mV for the OER. As the HER and OER bifunctional catalyst, Ni–Fe–Se/NF can split alkaline water with total voltages of ∼1.52 V and ∼1.66 V at 10 mA cm−2 and 100 mA cm−2, respectively, and remain stable over 50 hours of operation in 1 M KOH.
✓ 已验证
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2015
·
IF 4.504
Dekang Huang,Yanping Luo,Shaohui Li,Mingkui Wang,Yan Shen
To realize a large-scale application of fuel cells, it is highly desirable to develop noble metal-free electrocatalysts for oxygen reduction reaction (ORR). Herein, a highly active electrocatalyst is synthesized by impregnating in situ generated iron(III)-1,10-phenanthroline complex on commercially high specific surface area carbon blacks and subsequent pyrolysis at high temperature. High ORR limiting current density (5.79 mA cm −2 ) and positive half-wave potential (0.859 V versus RHE) over this electrocatalyst with a mass loading of 0.2 mg cm −2 can be achieved in 0.1 M KOH solution, which are very comparable with the benchmark Pt/C electrocatalyst. Detailed investigations have revealed the existence of nitrogen doped carbon (N-C), nitrogen coordinated to Fe (Fe-N), and Fe@Fe 3 O 4 core-shell nanoparticles in this composite electrocatalyst. The high activity of this electrocatalyst is attributed to the synergistic effect among them.
✓ 已验证
DOI
高影响因子
Journal of Environmental Sciences
·
2019
·
IF 3.556
Kaiyuan Zheng,Yuqiao Song,Xu Wang,Xin Li,Xuhui Mao,Dihua Wang
Herein, with the exploitation of iron and nickel electrodes, the 2,4-dichlorophenol (2,4-DCP) dechlorinating processes at the anode and cathode, respectively, were separately studied via various electrochemical techniques (e.g., Tafel polarization, linear polarization , electrochemical impedance spectroscopy). With this in mind, Ni/Fe nanoparticles were prepared by chemical solution deposition, and utilized to test the dechlorination activities of 2,4-DCP over a bimetallic system. For the iron anode, the results showed that higher 2,4-DCP concentration and solution acidity aggravated the corrosion within the electrode. The charge transfer resistance ( R ct ) values of the iron electrode were 703, 473, 444, and 437 Ω ∙ cm 2 for the initial 2,4-DCP concentrations of 0, 20, 50, and 80 mg/L, respectively. When the bulk pH of the 2,4-DCP solution varied from 3.0, 5.0 to 7.0, the corresponding R ct values were 315, 376, and 444 Ω ∙ cm 2 , respectively. For the nickel cathode, the reduction current densities on the electrode at − 0.75 V (vs. saturated calomel electrode) were 80, 106, and 111 μA/cm 2 , for initial 2,4-DCP concentrations of 40, 80, and 125 mg/L. The dechlorination experiments demonstrated that when the initial pH of the solution was 7.0, 5.0, and 3.0, the dechlorination percentage of 2,4-DCP by Ni/Fe nanoparticles was 62%, 69%, and 74%, respectively, which was in line with the electrochemical experiments. 10 wt.% Ni loading into Ni/Fe bimetal was affordable and gave a good dechlorination efficiency of 2,4-DCP, and fortunately the Ni/Fe nanoparticles remained comparatively stable in the dechlorination processes at pH 3.0.
✓ 已验证
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2022
·
IF 9.965
Guozhen Qin,Jianfeng Zheng,Yifan Li,Yatao Yang,Xingmin Liu,Xiaojin Han,Zhanggen Huang
Mainly exposed crystal facets and controllable morphology play a key role in the final performance of the preparation of specific nanomaterials . In the present study, a metal–organic framework pyrolysis method without adding solvent modifiers was developed. By adding CO in the calcination atmosphere to change atmosphere ratio, Fe 3 O 4 nanostructures are exposed with different crystal planes and evaluated their performance in NH 3 -SCR reaction. This study proves that SCR catalytic activity of Fe 3 O 4 nanocrystals is dependent on morphology and crystal facet. Compared with materials exposed (1 0 0), catalysts with more (1 1 1) show stronger deNO x performance. The preferential exposure of Fe 3 O 4 (1 1 1) crystal facets increases the concentration of adsorbed oxygen on the catalyst, showing higher surface acidity , and enhances the interaction among NO, O 2 and catalyst, which is conducive to SCR reaction. This is supported by DFT calculations . The results present a great application prospect in preparing nanomaterials with specific crystal structures to effectively treat pollutants.
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2026
·
IF 6.7
Yongli Yang,Qingxiu Shi,Chao Wu,Yujun Si
Pd nanoparticles were encapsulated within the Fe, N-doped carbon nanotubes. • The catalyst provides metallic Pd and Fe-N x as dual active sites to ORR. • Thinner, mesoporous and defective carbon walls of the nanotubes were constructed. • The catalyst shows outstanding ORR properties and practical performance. The cost, activity and durability of Pd-based catalyst can be balanced by supporting Pd on carbon materials. Herein, we report an oxygen reduction reaction (ORR) catalyst fabricated by encapsulating Pd nanoparticles within Fe, N doped carbon nanotubes, in which metallic Pd and Fe-N x serve as dual active sites. The porosity of carbon nanotube walls was tailored through a sequential process involving pyrolysis, acid leaching, and a second pyrolysis step. The resulting catalyst, Pd@FeNC7A8, exhibits smaller nanotubes with thinner carbon walls, more mesopores and greater defectivity, collectively enhancing the accessibility of the encapsulated Pd nanoparticles. Consequently, the Pd@FeNC7A8 exhibits reduced diffusion/mass-transport resistance with 33 Ω·s −1/2 of Warburg coefficient, compared with 43 Ω·s −1/2 of the control catalyst, Pd@FeNC48A, with compact carbon structure. Pd@FeNC7A8 catalyst delivers 0.904 V of half wave potential, 5.209 mA cm −2 of limited current density, and 48 mF cm −2 of electrochemical active surface area, outperforming Pd@FeNC48A in ORR performance. It also exhibits superior methanol resistance and durability compared with Pt/C. Moreover, the Pd@FeNC7A8-based the Zn-air battery demonstrates a higher discharge voltage, greater power density and specific capacity compared to its Pt/C-based counterpart, highlighting the potential of this catalyst in practical applications. Download: Download high-res image (144KB) Download: Download full-size image
✓ 已验证
DOI
高影响因子
Advanced Powder Materials
·
2023
·
IF 0
Cheng Li,Yatian Deng,Liping Yang,Bo Liu,Dong Yan,Liyuan Fan,Jian Li,Lichao Jia
Sr 2 FeCo 0.2 Ni 0.2 Mo 0.6 O 6-δ (SFCNM) and Sr 2 FeNi 0.4 Mo 0.6 O 6-δ (SFNM) were prepared as the hydrogen electrode materials for solid oxide cells (SOCs) and comparatively investigated by density function theory (DFT) and experiments to demonstrate the benefit of Co addition. The reduced SFCNM (R-SFCNM) and SFNM (R-SFNM) contain exsolved Fe–Co–Ni and Fe–Ni nanoparticles, respectively. DFT indicates that Fe–Co–Ni has optimized combination of the d-band center (descriptor of catalyst activity) and adsorption behavior for H 2 O, H 2 , H, and OH. The cell with SFCNM hydrogen electrode, La 0.8 Sr 0.2 Ga 0.8 Mg 0.2 O 3-δ (LSGM) electrolyte, and La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF) oxygen electrode (Cell-SFCNM) demonstrates a higher performance than that with an SFNM hydrogen electrode (Cell-SFNM) at temperatures between 700 and 850 °C in both solid oxide fuel cell (SOFC, 3% H 2 O-97% H 2 /air) and solid oxide electrolysis cell (SOEC, 20% H 2 O-80% H 2 /air) modes. At 850 and 700 °C, the peak power density is 1.23 and 0.48 W·cm −2 in SOFC mode, while the current density is 1.25 and 0.37 A·cm −2 at 1.3 V in SOEC mode, respectively. The performance degradation rates at 750 °C are 0.17 mV·h −1 in SOFC and 0.15 mV·h −1 in SOEC modes within 150 h, which are improved by Co doping.
✓ 已验证
DOI
JOURNAL OF POWER SOURCES
·
2019
·
IF 7.467
Yunfeng Zhan,Hongbin Zeng,Fangyan Xie,Hao Zhang,Weihong Zhang,Yanshuo Jin,Yueli Zhang,Jian Chen,Hui Meng
This work reports a rational design of non-precious metal catalyst for oxygen reduction reaction in acidic media to be used in polymer electrolyte membrane fuel cell. A strategy is designed to avoid the agglomeration of metal compound during the pyrolysis of precursor. MgO template is introduced into a 1-10-phenanthroline-iron (II) precursor to promote the evolution of Fe-Nx active sites while avoiding the formation of inactive species. The template also contributes to the formation of micro/mesoporous structure. The as-prepared catalyst shows good performance in half-cell test with half-wave potential of 0.80 V in acidic media. The catalyst reaches a current density of 0.76 A cm −2 at 0.6 V iR-free along with encouraging durability in H 2 –O 2 fuel cell test.
✓ 已验证
DOI
高影响因子
DALTON TRANSACTIONS
·
2017
·Vol. 46
·期 45
·15947-15953
·
IF 4.029
Ming Zhong,Dong-Hui Yang,Ling-Jun Kong,Wei Shuang,Ying-Hui Zhang,Xian-He Bu
Developing high-performance electrode materials to replace a traditional graphite electrode is critical for the commercialization of lithium ion batteries, which however still remains a great challenge. Herein, we report a suitable method to synthesize a series of well-dispersed nanostructured Co3O4–CoFe2O4 composites (CCFs) from bimetallic metal–organic frameworks (BiMOFs) with varied Fe3+/Co2+ molar ratios. When used as anodes for lithium ion batteries, the CCF-12 composite exhibits a maximum initial discharge capacity of 1328 mA h g−1, a reversible capacity of 940 mA h g−1 at 100 mA g−1 after 80 cycles, and a better rate capability in comparison with those of pure Co3O4 and other CCF composites. The well-dispersed structure and small particle size are believed to mainly contribute to the outstanding electrochemical performance of CCF-12 electrodes.
✓ 已验证
DOI
高影响因子
FUEL
·
2024
·
IF 6.7
Wei Fu,Muhammad Kashif,Chen Cai,Jiayin Chen,Hao Zhou,Bingtao Zhao,Philippe M. Heynderickx,Yaxin Su
The hydrothermal technique was applied to prepare a new metal–organic framework, MIL-100(Fe), which was modified by ultrasonic impregnation with different wt % of copper. The results showed that the NO x conversion over 2.3Cu-MIL-100(Fe) was 100 % at 275 °C and maintained at ≥ 85 %, with N 2 selectivity ≥ 90 % in the temperature range of 275–400 °C and high SO 2 resistance. An increase in the Cu content up to 2.3 wt% showed the highest surface area (1206 m 2 /g) observed in N 2 adsorption–desorption. The results show that the introduction of Cu increased the oxygen vacancies on the catalyst surface. Electron transfer and a synergistic effect were observed between Cu and Fe. The shift of the reduction peaks to lower temperatures after the addition of Cu confirmed that Cu improved the reducibility of the catalysts. The 2.3Cu-MIL-100(Fe) exhibited the highest Lewis content (44.97 μmol/g), which functions as an active site for the selective catalytic reduction (SCR) reaction. By precisely controlling the acid-base properties of the catalyst, the specificity for the desired products can be increased in complicated reaction systems, especially in hydrocarbon-SCR technology.
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2025
·
IF 13.2
Zunqing Wen,Xiaoguo Shi,Huiying Sui,Minglu Zhang,Longquan Zhang,Yawei Gu,Qing Feng,Ke Ma,Na Zhang,Mingzhe Wang,Ruiyan Zhang,Chongqing Xu,Zengjin Li,Rong Xue
Numerous studies have revealed that air oxidation behavior profoundly impacts pyrite properties. Whereas its influence on pyrite Fenton performance remains controversial. Herein, pyrite FeS 2 nanoparticles synthesized by facile wet-mechanochemical method was employed as oxidation model and its oxidation degree was evaluated by XPS depth profiling technique. Based on theoretical calculation and experimental evidence, the properties and Fenton performance of surface oxidized pyrite (SOP x ) were comprehensively assessed. With oxidation degree increase, free radical generation selectivity was alternated from •O 2 – to •OH, and the selectivity to •OH showed strong correlations with {210} facet ratio, Fe(Ⅱ)-O and sulfur vacancies (SVs) contents. The oxidation degree dependence in •OH selective production primarily stemmed from different electron-donating and Fe 2+ releasing capacity. Moderately oxidized pyrite (SOP 4 ) with high {210} facet ratio, SVs and Fe(Ⅱ)-O contents could donate electrons for H 2 O 2 barrierless dissociation and Fe 2+ /Fe 3+ redox-cycle, and cause more Fe 2+ releasing to enhance homogeneous Fenton reaction. As the oxidation degree increased (from SOP 0 to SOP 4 ), the Fenton systems demonstrated a significant enhancement in sulfadiazine (SDZ) degradation kinetics, with the rate constant increasing from 0.02039 to 0.06904 min −1 . The superior SDZ removal efficiency in SOP 4 system at wide pH range (5–9) indicated moderate oxidation significantly improved its decontamination and practical application ability. However, the amorphous iron oxide layer generated in the over-oxidized pyrite (SOP 6 ) impaired its catalytic activity, resulting in a decrease of the rate constant (0.0485 min −1 ). These findings unveiled the mystery of Fenton performance regulated by FeS 2 oxidation via {210} facet, SVs and Fe(Ⅱ)-O, and offered fresh insights into developing targeted structures for tunable performance.
✓ 已验证
DOI
高影响因子
PHOTOCHEMISTRY AND PHOTOBIOLOGY
·
2024
·
IF 2.6
Rong Zhang,Zhuannian Liu,Taoli Chen
Developing cost-effective and efficient photo-Fenton catalysts is crucial for advancing photo-Fenton technology. MoS 2 is a representative transition metal disulfide with attractive photoresponsiveness, making it ideal for preparing composite photo-Fenton catalysts. In this study, natural molybdenite was innovatively utilized as a source of MoS 2 (OM) to synthesize a low-cost and efficient Fe@MoS 2 (OMF) composite photo-Fenton catalyst by comminution and adsorption, which was then applied to the remediation of antibiotic-contaminated water. The OMF composites exhibited significant catalytic activity, with a kinetic rate constant of 0.022 min −1 , which was 3.1 times higher than that of the original OM (0.007 min −1 ), indicating a 3% increase. This was attributed to the synergistic effect of many photogenerated electrons and reversible Mo 4+ /Mo 6+ redox pairs, which accelerated the regeneration of Fe 2+ . After three cyclic tests, the concentrations of dissolved Fe 2+ and Mo 2+ ions remained below 0.38 mg/L and 0.17 mg/L, respectively. This indicates the high reusability of the catalyst in cyclic experiments. Ultimately, the main active species, •OH and •O 2 − , were generated during the photo-Fenton process, contributing significantly to TC degradation. This study may serve as a reference for the development and application of natural mineral composite photo-Fenton catalysts in the treatment of organic wastewater.
✓ 已验证
DOI
PubMed
高影响因子