Analytical Methods
·
2022
·Vol. 14
·期 12
·1254-1260
·
IF 3.532
Yamin Si,Feng Jiang,Liang Qiang,Xiaotong Teng,Chengbin Gong,Qian Tang
Dibenzothiophene and its derivatives in gasoline and diesel would release sulfur oxides during combustion, and this is harmful to human health and the environment. This paper reports a method based on a visible-light-responsive molecularly imprinted polyurethane (VMIPU) to monitor trace dibenzothiophene in gasoline. The VMIPU was prepared by a polyaddition reaction using N,N-bis-(2-hydroxyethyl)-4-phenylazoaniline as the functional monomer, dibenzothiophene as the template molecule, diphenylmethane diisocyanate as the crosslinker and castor oil as the chain extender. The VMIPU showed good visible-light-response and specific adsorption for dibenzothiophene. The trans → cis photoisomerization rate constant of azobenzene chromophores in the VMIPU shows a linear relationship with the dibenzothiophene concentration in the range of 0–20 μmol L−1. This was used to estimate trace dibenzothiophene in spiked gasoline with recoveries of 95.7–101.0% and relative standard deviations of 7.0–12.7%.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
PROCESS SAFETY AND ENVIRONMENTAL PROTECTION
·
2022
·
IF 7.926
Gaofeng Zhou,Yongsheng Fu,Runyu Zhou,Li Zhang,Linyue Zhang,Jiewen Deng,Yiqing Liu
In this study, a novel heterogeneous peracetic acid (PAA)-based advanced oxidation process (AOP), viz. cobalt ferrite combined with PAA (CoFe 2 O 4 /PAA), was used to degrade organic contaminants . The best pH for rhodamine B (RhB) degradation in CoFe 2 O 4 /PAA system was at 7, and approximately 95% RhB could be removed within 10 min at this pH. Radical scavenging experiments indicated that organic radicals (i.e., CH 3 COO • and CH 3 COOO • ) were the dominant reactive species for RhB degradation. The X-ray photoelectron spectroscopy (XPS) analysis for the fresh and used catalysts suggested that the catalytic reaction mainly occurred on the surface of the catalyst. Increasing PAA dosage and CoFe 2 O 4 dosage could enhance the removal of RhB, while excess CoFe 2 O 4 dosage inhibited its degradation probably due to the clumping effect of magnetic nanoparticles . Five degradation products of RhB by CoFe 2 O 4 /PAA were identified and two degradation pathways of RhB were subsequently proposed, including bond cleavage and hydroxylation . CoFe 2 O 4 exhibited an excellent stability and reusability , and the removal rate of RhB could maintain at 92.4% after four cycles. Several kinds of organic contaminants were selected to evaluate the applicability of CoFe 2 O 4 /PAA system, and the results suggested that CoFe 2 O 4 /PAA system exhibited a selectivity for different contaminants.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CHROMATOGRAPHY A
·
2022
·
IF 4.601
Chao Fan,Jia Chen,Hui Li,Kaijun Quan,Hongdeng Qiu
Two new hydrophilic-hydrophobic and acid-base balanced liquid chromatographic stationary phases were obtained by using two long-chain monomers including undecylenic acid (UA) and oleic acid (OA) combined with short-chain 4-vinyl pyridine (Py) in-situ polymerized on silica microspheres surfaces, respectively. These two stationary phases can be used for reversed-phase liquid chromatography (RPLC) and hydrophilic interaction liquid chromatography (HILIC) modes. Hydrophilic, hydrophobic, acidic and basic analytes can be separated on two new stationary phases in RPLC or HILIC mode. Compared with commercial hydrophobic C18 columns and other HILIC columns, two new stationary phases have excellent selectivity and separation performance in the separation of 9 polycyclic aromatic hydrocarbons, 10 aromatic acids, 10 anilines and 5 oxazolidinones, respectively. This novel polymer-functionalized silica design strategy has opened up new ideas for the future of mixed-mode stationary phases with multiple functions and specificity.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
APPLIED SURFACE SCIENCE
·
2022
·
IF 7.392
Yuenan Pan,Qi Chu,Shuang Guo,Sila Jin,Eungyeong Park,Yeonju Park,Yantao Sun,Lei Chen,Young Mee Jung
The purpose of this paper is to study the charge transfer (CT) process of a Ag/MBA/PAN system with different thicknesses of PAN and explore its SERS enhancement mechanism. It is found that as the PAN thickness is increased, the frequency and intensity of the characteristic MBA band gradually increases. The intensity of the b 2 mode increases significantly, which is attributed to the CT mechanism. As the PAN thickness is increased, the degree of CT (ρ CT ) gradually increases, which is due to the excited SPR from Ag. The electromagnetic enhancement mechanism, which occurs at the interface between PAN and Ag, generates hot electrons and rearranges the interface between PAN and Ag, thereby promoting electron transfer for the whole CT in Ag/MBA/PAN. These results show that CT occurs from the Fermi level of Ag to the LUMO level of MBA and then to the LUMO level of PAN. Additionally, the direction of CT is verified by 2D-COS. Therefore, this study not only reveals the ultrahigh SERS activity of the substrate but also explains the detailed process of regulating the substrate through the PAN thickness, which affects the SERS mechanism. This conductive polymer will open up a new horizon of SERS research and applications.
✓ 已验证
产品关联
DOI
高影响因子
MACROMOLECULAR RAPID COMMUNICATIONS
·
2022
·Vol. 43
·期 18
·2100836
·
IF 5.006
Qingyin Li,Ying Cheng,Shumaila Razzaque,Zuolin Cao,Shijie Ren,Bien Tan
In this work, novel hypercrosslinked polymer-based hollow microporous organic capsules with a polyaniline (PANI)-modified shell (PANI@S-HMOCs) are prepared by in-situ polymerization of aniline in the porous structure of the sulfonated hollow microporous organic capsules (S-HMOCs). PANI@S-HMOC1, PANI@S-HMOC2, and PANI@S-HMOC3 are made by adjusting S-HMOCs and aniline weight ratios of 4:1 and 3:1, and 2:1, respectively. The characterizations of PANI@S-HMOCs demonstrate that electrostatic interaction between aniline and sulfonic acid groups plays an important role in encapsulating PANI in the pores of the shell. The content of PANI shows an evident effect on the porosity of PANI@S-HMOCs, and an appropriate polyaniline loading amount may increase the surface area. PANI@S-HMOC1 and PANI@S-HMOC2 have higher BET surface areas (529 and 503 m 2 g −1 ) than S-HMOCs (424 m 2 g −1 ), but PANI@S-HMOC3 has lower BET surface area (380 m 2 g −1 ). Based on the structural and textural features, PANI@S-HMOC2 shows good adsorption performance for Cr(VI) from aqueous media (156 mg g −1 , pH = 2, and 27 mg g −1 , pH = 7).
✓ 已验证
产品关联
DOI
PubMed
高影响因子
TALANTA
·
2022
·
IF 6.556
Chonghui Zhu,Hua Xue,Hongran Zhao,Teng Fei,Sen Liu,Qidai Chen,Bingrong Gao,Tong Zhang
A flexible dual functional electrochemical sensor based on macroscopic polyaniline (PANI) film is reported. The PANI film is prepared by interfacial synthesis without any additional templates and surfactants, and is easily transferred from the water surface to any substrate. The surface of PANI film is flat and has a certain degree of crystallization. The PANI film exhibits good electrochemical properties, which is attributed to the order structure of PANI. The flexible sensor based on PANI film exhibits good electrochemical performances to pH and lactate. And the flexible PANI sensor has good reproducibility, selectivity and long-term stability. Meanwhile, the PANI sensor is also applied to detect the actual sample (such as food and human sweat), and the results are in accordance with the commercial pH meter, indicating the reliability of the PANI sensor.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ANALYTICA CHIMICA ACTA
·
2022
·
IF 6.911
Xiaohui Niu,Simeng Yan,Letong Wang,Jinliang Chen,Rui Zhao,Hongxia Li,Jian Liu,Kunjie Wang
So far, the fabrication of chiral metal-organic framework (CMOF) is difficult to predict and the chiral functionality mainly comes from the building blocks that is a part of the frameworks. The induction effect in the chiral nanochannels of the metal-organic framework (MOF) makes achiral polymers have chiral properties, which has not been well explored. Therefore, CMOFs with chiral nanochannels or chiral pores appear to have special functions. Herein, CMOFs (D-his-ZIF-8) with chiral micropores or chiral nanochannels are prepared through a simple 2-methyl imidazolate in-situ substitution by d -histidine. The unmodified polyaniline with chirality ( c -PANI) was synthesized in chiral nanochannels and pores of CMOF, which brought about chiral induction from the chiral nanochannels and pores of CMOF to c -PANI chains. The circular dichroism shows that the c -PANI chains released from the chiral nanochannel still maintains the chiral properties even leaves the chiral nanochannel. It can be seen from the electrochemical results that c -PANI has excellent conductivity, and the conductivity of CMOF is very poor. Electrochemical recognition showed that both CMOF and c -PANI have certain chiral recognition effects for L-Trp and D-Trp, from which the optimal recognition effect was obtained from c -PANI chains. This shows that the excellent conductivity of c -PANI not only expands the electrochemical signal, but also the helical structure of the c -PANI chains accelerates the distinction of chiral molecules. This study provides a novel perspective to induce chiral polymer chains with better conductivity in the nanochannels of CMOF.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2022
·Vol. 139
·期 20
·52180
·
IF 3.057
Kongsen Hu,Jiyuan Feng,Nan Lv,Wenbo Jiang,Zhiwei Lyu,Qing Hai
Exploitation of soft piezoelectric sensing materials is fundamental to the research of energy-harvesting devices and wearable electronics. However, a big challenge of piezoelectric materials application in micro-scale sensing systems is to address the restrictions of electrode compatibility, miniaturization, multistep assembly, and high cost. Here, we propose a simple strategy to develop the coinstantaneous construction of piezoelectric materials and nanoresistance networks by fabricating electrospun piezoelectric-conductive (polyacrylonitrile)//(polyaniline/polyvinyl pyrrolidone) (denoted [PAN]//[PANI/PVP]) Janus nanofibers (NFs). This peculiar Janus structure can collect and output voltage by conductive paths based on the Wheatstone bridge principle. Moreover, owing to the nanoscale asymmetric geometry for efficient polarization and induced charges collection, the Janus NFs show superior piezoelectric properties. As a result, flexible (PAN)//(PANI/PVP) Janus nanofibers integrated membrane (JNFIM) dispensing with two flat electrodes can directly output a high voltage of 2 V under a tiny force of 1 N. Furthermore, the JNFIM enables to detect pressures with extra-high linear sensitivity (1.88 V N −1 ) and low detection limit (0.1 N). Thus, our work provides a simple route for the development of nanoscale, low-cost, and high-sensitivity integrated materials for pressure sensing, revealing promising applications in miniature robotics and wearable devices.
✓ 已验证
产品关联
DOI
高影响因子
ChemElectroChem
·
2022
·Vol. 9
·期 7
·e202101574
·
IF 4.782
Jia-Lin Du,Xu Bao,Wei-Bin Zhang,Lun Zhang,Yao-Wen Guo,Xia Zhou,Xian-Li Zhang,Shan-Shan Chai,Shao-Bo Guo,Xiong-Wei Han,Jianping Long
Graphical Layer by layer : The electrochemical kinetics of layered manganese phosphate are improved via interfacial polypyrrole chemical binding for electrochemical supercapacitor application. The major limitation of low-cost and high-safety aqueous manganese-based materials for electrochemical energy storage is largely hampered by their poor cyclic stability, usually caused by the manganese dissolution and interfacial kinetics. Herein, we synthesized a manganese phosphate material via interfacial polypyrrole chemical binding, with unique structural properties for aqueous supercapacitor application. It exhibited higher specific capacitance, remarkable rate performance and better cycle stability compared to bare manganese phosphate. In contrast with interfacial polypyrrole coating on manganese phosphate nanosheets, the polypyrrole could form a Mn−N bond with the manganese phosphate, indicating stable chemical binding. Thus, the appropriate interfacial chemical binding is an efficient strategy to improve the nanostructure stability and electrochemical kinetics of manganese-based materials for aqueous electrochemical energy storage.
✓ 已验证
产品关联
DOI
高影响因子
Advanced Composites and Hybrid Materials
·
2022
·Vol. 5
·期 2
·1003-1016
·
IF 11.806
Xie Wenhao,Yao Feichong,Gu Hongbo,Du Ai,Lei Qin,Naik Nithesh,Guo Zhanhu
Herein, a novel three-dimensional nanocomposite aerogel (rGO/Fe 3 O 4 /PANI NAs) with outstanding magnetoresistance and piezoresistance was manufactured by the in-situ polymerized polyaniline nanoarrays (PANI NAs) surrounding magnetic reduced graphene oxide (rGO/Fe 3 O 4 ) aerogel that was prepared through the combination of hydrothermal method and lyophilization method. This rGO/Fe 3 O 4 /PANI NAs nanocomposite aerogel with 60 wt.% loading of PANI NAs well preserved the porous structure and gained a superior mechanical strength (121.04 kPa) compared with that of rGO aerogel, rGO/Fe 3 O 4 aerogel, and rGO/PANI NAs aerogel (43.54, 58.12, and 116.98 kPa, respectively). The rGO/Fe 3 O 4 /PANI NAs nanocomposite aerogel could hold its original state with almost 100% recovery ratio after cycling compression tests under 80% of deformation strain at a suitable compression rate of 5 mm min −1 . The introduction of PANI NAs into the rGO/Fe 3 O 4 aerogel also brought a satisfactory piezoresistive performance with a large gauge factor up to 2.83 and a superb stability for the electrical signal output (which was decreased only 5.80% after 500 compression cycles) to the rGO/Fe 3 O 4 /PANI NAs nanocomposite aerogel. The loading of Fe 3 O 4 and PANI NAs also provided rGO/Fe 3 O 4 /PANI NAs nanocomposite aerogel with a negative magnetoresistance value up to − 4.37%. The magnetoresistance was explained via the amelioration of spin transport in the material. The unique negative magnetoresistance and excellent piezoresistance make rGO/Fe 3 O 4 /PANI NAs nanocomposite aerogel a promising candidate for the development of advanced electronic devices. Graphical abstract A novel three-dimensional nanocomposite aerogel (rGO/Fe 3 O 4 /PANI NAs) exhibits amazing negative magnetoresistance and outstanding piezoresistive performance.
✓ 已验证
产品关联
DOI
高影响因子
Materials Today Chemistry
·
2021
·
IF 8.301
Ruiqi Li,Lixue Yang,Changqing Zhou,Guoli Zhang,Jiaxiang Tian,Wencong Wu
The loss of superhydrophobicity due to mechanochemical damage is critical for superhydrophobic surfaces, and rapid self-healing is significant in maintaining surface durability. Herein, a novel, fast, self-healing superhydrophobic sponge capable of all-weather heating was polymerized in an eco-friendly aqueous system and dip-coated using fluorine-free and non-toxic reagents. Benefiting from the photothermal and Joule-heating performance of polyaniline (PANI) and multiwalled carbon nanotubes (MWCNTs), all-weather heating could be achieved. The equilibrium surface temperature (EST) of the as-prepared sponge could rapidly reach 105°C under irradiation of 1.0 kW/m 2 for 20 s, and the EST exceeded 120°C with supplementary 18 V treatment. Impressively, after O 2 plasma etching for 1 min or after being immersed in hydrogen peroxide (H 2 O 2 ) solution for 24 h, the water contact angle (WCA) of self-healing superhydrophobic polyurethane (PU) sponge (SHSPS) can be restored to 155°C under simulated sunlight for 2 min because of the rapid migration of low surface energy polydimethylsiloxane (PDMS) chains, which is the fastest recovery achieved to the best of our knowledge. In addition, the modified sponge exhibited a significant antifouling capability for particulate contaminants and organic pollutants, extending service life. Our preliminary results demonstrated that the modified sponge prepared in the current work is fully qualified in multiple applications, including oil-water separation, viscous oil treatment, seawater evaporation and desalination, de-icing, and anti-icing.
✓ 已验证
产品关联
DOI
高影响因子
BIOMACROMOLECULES
·
2021
·
IF 6.988
Yingqi Heng,Genhui Teng,Yang Chi,Dongying Hu
The biomass-based inter-transmission network architecture is expected to act on all-solid-state supercapacitors (ASSSCs) by building excellent conductive paths and achieving high ionic conductivity to promote their development as future electronic devices. Here, biomass-derived hybrid organogel electrodes constructed by incorporating polyaniline (PANI) into cellulose/dealkaline lignin (C/DL) film architectures exhibit an impressive specific capacitance (582 F g–1 at 1 A g–1) due to the effective dispersion and doping of PANI. Moreover, the specific capacitance of the best C/DL-PANI electrode is nearly 19 times higher than that of a cellulose-PANI electrode, which is attributed to the contribution of DL to the pseudocapacitance. ASSSCs assembled using the C/DL-PANI electrodes and the DL gel electrolyte exhibit excellent specific capacitance (344 F g–1 at 1 A g–1), Coulombic efficiency (∼100% for 5000 cycles), cycle stability (85.7% for 5000 cycles at 1 A g–1), and energy density (58.1 W h kg–1 at 0.5 kW kg–1). The ASSSCs showed a comparable or even higher electrochemical performance than the reported PANI-based or biomass-based ASSSCs, which can be due to the conductive network of the biomass-derived electrodes, the migration of ions between the electrodes through the gel electrolyte ion pathway, and the interfacial synergy. This innovative work paves the way for the development of ASSSC applications based on biomass materials.
✓ 已验证
产品关联
DOI
PubMed
高影响因子