APPLIED SURFACE SCIENCE
·
2019
·
IF 5.155
Wen-Li Xin,Lian-Hua Xu,Kun-Kun Lu,Dan Shan
Fe-N catalysts are one of the promising candidates with efficient oxygen reduction reaction (ORR) activities comparable to Pt-based catalysts. Therefore, in this work, a novel Fe-N based electrocatalyst with high activity, porous structure, and durability were prepared. Highly active N,N′-carbonyldiimidazole (CDI) was used to form zinc-based zeolitic imidazole frameworks involved with zinc carbonate (Zn-ZIFs@ZnCO 3 ). Fe-doping can be feasibly achieved by partial substitution Zn by Fe using Fe (NO) 3 . Owing to the presence of ZnCO 3 and Fe 3+ , carbonization of Fe/Zn-ZIFs@ZnCO 3 at 925 °C under N 2 atmosphere endows the pyrolysis products with many highly active heterostructures of 3D graphene structure. The obtained Fe-N@ZnO possesses superior ORR performance to commercial 20% Pt/C catalysts, such as positive half-wave potential (0.851 V), good durability and methanol tolerance in 0.1 M KOH.
✓ 已验证
DOI
高影响因子
FUEL
·
2025
·
IF 7.5
Xingping Kai,Lesheng Wang,Tianhua Yang,Wenwen Yan,Zhaowei Liu,Bingshuo Li,Tao Zhang,Rundong Li
The extraction of lignin-derived pyrolysis oils has received much attention as a potential alternative to conventional petroleum-based fuels and chemicals. This study presented a one-step synthesis approach to prepare Fe-Ni bimetallic-modified lignin-based biochar (xFe-yNi/LC) catalysts, and investigated the effects of bimetallic interactions on aromatic hydrocarbon formation and its pathways during the ex-situ catalytic fast pyrolysis of enzymatically hydrolyzed lignin. The results demonstrated that the combination of Fe and Ni not only modified the porous structure of the catalyst but also formed Fe-Ni alloy, regulating the content of Lewis acid sites to enhance aromatic hydrocarbon production. When the catalyst was 20Fe-5Ni/LC, the Lewis acid site content reached a maximum of 38.68 μmol/g. Additionally, the aromatic hydrocarbon content reached a peak value of 19.06 area% when the ratio of lignin to 20Fe-5Ni/LC was 1:2. This represented an improvement of 47.98 % compared to the lignin pyrolysis without the catalyst. The bimetallic catalyst exhibited excellent thermal stability, with the aromatic hydrocarbon content still achievable at 8.66 area% after four cycles of experiments.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2025
·
IF 13.2
Ruiyan Wang,Tiantian Luo,Hao Yan,Jiale Wang,Weilong Li,Qi Zhou
This study developed a facile method to fabricate ultrathin carbon nanosheets anchoring high-density iron single atom catalyst (Fe 0.5 SA, Fe loading >7.2 %) by combining the Ultra-fast coating and Template gasification, used for constructing a highly efficient non-radical peroxymonosulfate (PMS) activation system. The asymmetric Fe-N 3 O coordination structure in Fe 0.5 SA serves as the key active site for PMS activation, binding with PMS to form a surface-active complex (Fe 0.5 SA/PMS*) that facilitates catalytic oxidation via the electron transfer pathway (ETP). density functional theory (DFT) results reveal that the oxygen in the Fe-N 3 O coordination optimizes the electronic structure of the Fe center, resulting in an upshifted d-band center, thereby significantly enhancing PMS adsorption and interfacial electron transfer. The Fe 0.5 SA/PMS system exhibited exceptional performance, achieving complete degradation of high-concentration tetracycline (TC, 200 mg/L) within 5 min, with a degradation rate constant of 1.834 min −1 . This value is 2.45, 9.81, and 4.64 times higher than those of Fe 1.5 SA/NC (with Fe clusters), Fe 2.5 NPs (with Fe nanoparticles), and NC (iron-free), respectively. Furthermore, Fe 0.5 SA demonstrated strong anti-interference capability, broad pH adaptability, high PMS utilization efficiency, selectivity toward electron-rich organic compounds, and effective performance in continuous-flow operation. This work not only proposes a promising strategy for the fine structural regulation of single-atom catalysts but also provides mechanistic insights into the Fe 0.5 SA-mediated, ETP-dominated PMS activation mechanism at the atomic level.
✓ 已验证
产品关联
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2025
·
IF 6.9
Jiaojiao Du,Tianzheng Cao,Pengfei Wu,Haijiang Kou,Zhicheng Yao,Pengfei Gao,Disheng Pan,Chao Zhang
In order to obtain materials with comprehensive microwave absorption performance for outdoor corrosive environmental applications, this paper constructed low-density CoFe-C porous polyhedrons with SiO 2 nanoparticles coating using ZIF-67 template, chemical synthesis, and sintering methods (abbreviated as CoFe-C@SiO 2 ). The different magnetic Fe contents (mass of raw material ferrocene) were used to adjust the microstructure and microwave absorption performance of CoFe-C@SiO 2 . The results show that after sintering, the C=N bond, C-N bond, and Co 2+ in ZIF-67 decomposed to generate Hcp-graphite C, Fcc-Co, and a small amount of CoO. Increasing Fe content reduced the reflection loss and increased the effective absorption bandwidth of CoFe-C@SiO 2 . The optimal absorption performance (a reflection loss of −58.3 dB, an effective absorption bandwidth of 5.41 GHz) at a thin thickness (1.70/1.73 mm) was obtained. The moderate attenuation constant and widest impedance matching band resulted in the optimal absorption performance. Dielectric loss was the primary loss mechanism of CoFe-C@SiO 2 . The simulation of radar cross section values confirmed the enormous potential of CoFe-C@SiO 2 to achieve stealth under radar detection by increasing the Fe content. Coating SiO 2 nanoparticles improved absorption and anti-corrosion performances of CoFe-C. This paper establishes a design strategy for high-performance radar-absorbing materials that are resilient to outdoor corrosion.
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2025
·
IF 8.3
Yu Ma,Haitao Zhang,Haizhou Zhang,Xinyuan Ren,Xiaochun Ma,Xiaoming Zhou,Yanlu Mu,Jiemei Yu,Taizhong Huang
Developing non-precious metal based catalysts is one of the most feasible ways to accelerate the application of hydrogen production technology by full water electrolysis with low-cost and high efficiency. In this work, hollow nanosphere structured Fe–Cu–Co trimetallic selenide based catalysts were successfully prepared by one-step hydrothermal method. The hollow nano-spherical shell structure was examined by using XRD, Raman, BET, SEM, TEM, XPS, etc. technologies. The catalytic performance for hydrogen evolution reaction (HER) of the catalysts was tested by LSV, Tafel, CV, EIS, i-t , etc . methods. The overpotential of FeCo 0.1 Cu 0.9 Se 2 catalyzed HER was only 191 (alkaline) and 112 mV (acidic) at 10 mA/cm 2 . The corresponding Tafel slope for HER is 180 mV/dec (alkaline) and 110 mV/dec (acidic), respectively. In addition, the FeCo 0.1 Cu 0.9 Se 2 also showed excellent long-time running stability. The current decay after continuous running 12 h in 0.5 M H 2 SO 4 and 0.1 M KOH electrolytes are 0.07 % and 0.271 %, respectively. FeCo 0.1 Cu 0.9 Se 2 catalyst with the hollow nanospherical structure exhibited excellent catalytic activity for HER. Density functional theory calculations show that the introduction of Co and Cu adjusted the electronic structure of FeCo 0.1 Cu 0.9 Se 2 and the special hollow nano-spherical structure provides enough active catalytic sites for HER. The nano-spherical structured multi-metal selenides show great potential to be high performance catalysts for HER in both alkaline and acidic electrolytes.
✓ 已验证
DOI
高影响因子
FUEL
·
2025
·
IF 7.5
Danni Ren,Xiaoguo Zhang,Wei Lu,Ziyi He,Meng Yang,Xiaodong Luo,Shenfu Yuan
Ni-Fe bimetallic catalysts demonstrate high catalytic activity and strong resistance to deactivation during biomass steam reforming (BSR). However, their activation and reaction with steam (H 2 O) are complex, and a deeper understanding of the underlying mechanisms is crucial for enhancing catalyst stability. This study systematically investigates the influence of H 2 O on the deactivation mechanisms of Ni-Fe/Al 2 O 3 catalysts, focusing on its dual role in modulating carbon deposition patterns and triggering metal particle sintering. Our experimental results reveal a paradoxical effect of steam: the introduction of H 2 O reduces the total amount of carbon deposits, it promotes the formation of structurally disordered carbon. Crucially, this disordered carbon is identified as the primary driver of catalyst deactivation. It not only physically blocks active sites but also accelerates the sintering of metal particles, leading to profound alterations of the catalyst’s surface architecture and a consequent loss of performance. Combining experimental results and DFT calculations, we reveal the energy barriers for carbon evolution and correlate them with catalytic stability. These insights provide a theoretical foundation for improving the deactivation resistance of the catalyst, controlling the structural type of carbon deposits, and optimizing the anti-sintering performance of the etallic catalysts.
✓ 已验证
产品关联
DOI
高影响因子
Arabian Journal of Chemistry
·
2022
·
IF 6.212
Run Yuan,Yihe Qin,Can He,Zichen Wang,Lu Bai,Hong Zhao,Zijian Jiang,Lingyao Meng,Xuwen He
It is important to develop a catalyst that has high catalytic activity and can improve the degradation efficiency of refractory organic pollutants in the catalytic ozonation process. In this study, Fe-Mn-Cu-Ce/Al 2 O 3 was synthesised via impregnation calcination for catalytic ozonation of bio-treated coking wastewater. The physical and chemical characteristics of the catalysts were analysed using X-ray diffraction (XRD), X-ray fluorescence spectrometry (XRF), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and Brunauer–Emmett–Teller nitrogen adsorption–desorption methods. The effects of catalyst dosage, pH, and reflux ratio on the degradation efficiency of wastewater were examined in laboratory-scale experiments. The chemical oxygen demand (COD) removal rate of bio-treated coking wastewater was estimated to be 52.76 % under optimal conditions. The experiments on the catalytic mechanism demonstrated that the surface hydroxyl formed by the Lewis acid sites on the surface of the catalyst can react with ozone as the active site forming the active oxygen (·OH, ·O 2 – , and 1 O 2 ), thereby efficiently degrading the organic pollutants in coking wastewater. Furthermore, a pilot-scale experiment on the catalytic ozonation of bio-treated coking wastewater was carried out using an Fe-Mn-Cu-Ce/Al 2 O 3 catalyst, while the effects of the initial pollutant concentration, ozone concentration, and gas flow on the COD removal rate were studied on a pilot scale. It was found that the COD removal rate of the wastewater was ∼ 60 % under optimal parameters. After the treatment, the wastewater steadily reached the coking wastewater discharge standard (COD < 80 mg/L), while the operating cost of catalytic ozonation reached ∼ 0.032$/m 3 , thereby paving the way toward economic engineering applications. The COD degradation kinetics in the bio-treated coking wastewater followed pseudo-second-order kinetics. Three-dimensional fluorescence and gas chromatography–mass spectrometry revealed that macromolecular organic pollutants in the bio-treated coking wastewater were greatly degraded. In summary, Fe-Mn-Cu-Ce/Al 2 O 3 exhibited good reusability, high catalytic activity, and low cost and has a wide application prospect in the treatment of coking wastewater.
✓ 已验证
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2022
·
IF 9.965
Haiqing Gao,Qin Ji,Bin Chi,Caixue Lin,Gang Ding,Yingxi Wang,Xiaolan Yu,Zushun Xu,Run Zhang,Ling Li,Jing Wang
Targeting excess H 2 O 2 in the tumor microenvironment, nanotheranostic agents for catalytic therapy are designed based on Fenton reaction, catalyzing H 2 O 2 into oxygen and hydroxyl radical ( OH). But the catalytic efficiency in tumor microenvironment is not satisfactory. In order to solve the problem, a series of bimetallic-dual ligands metal-organic frameworks Fe/Tm-MOFs were designed, that Fe 3+ and Tm 3+ as metalions, 2-methylimidazole and trimesic acid as ligands. Due to the doped Tm 3+ in Fe/Tm-MOFs and the conjugated structures formed by two ligands, the rate of electron transfer was improved, thus promoting the generation of OH at some extent. In addition, the photothermal effect of Fe/Tm-MOFs further promotes the generation of OH, which was evidenced by the 3,3′,5,5′-tetramethylbenzidine(TMB). Combining the drug loading and release capabilities of Fe/Tm-MOFs, synergetic therapy of photothermal/chemo-/catalytic therapy can be achieved. In vitro results reveal that DOX release behaviors are both pH- and thermal-responsive. In vivo anti-cancer results show that the tumors of mice almost disappeared within 10 days, which were injected with Fe/Tm-MOFs/DOX and irradiated with 808 nm for 10 min. Thus, an excellent therapeutic performance has been achieved. Besides, Fe/Tm-MOFs can serve as a multimodality bioimaging contrast agent, covering fluorescence imaging, photothermal imaging and magnetic resonance imaging. Thus, an all-in-one nanotheranostic agent is constructed, improving the catalytic efficiency and providing a novel method to design an efficient nanotheranostic agent.
✓ 已验证
DOI
PubMed
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2021
·
IF 8.128
Mingliang Ma,Yuxin Bi,Zhengguo Jiao,Jiewei Yue,Zijian Liao,Yan Wang,Yong Ma,Weibo Huang
At present, the magnetic metal/carbon composites have been widely explored for microwave absorption (MA), which effectively integrate the characteristics of magnetic and dielectric materials . As a typical material, metal–organic framework (MOF) shows tremendous potential as a precursor or template. However, its development is limited by the inferior impedance matching. Herein, a novel rod-like Fe/Fe 3 O 4 /FeN/N-doped carbon (FON/NC) composite was synthesized via dual-ligand strategy and following calcination . The outer polypyrrole (PPy) shell, obtained by a facile polymerization method, effectively optimized the impedance matching and observably enhanced the MA capacity. Both the multi-component loss mechanism and unique porous core–shell structures of MOF-derived composites were beneficial for microwave attenuation . The effects of filler loadings (20 wt%, 25 wt%, 30 wt% and 35 wt%) on electromagnetic (EM) properties of FON/NC@PPy composites were discussed. Remarkably, as-obtained composites exhibited a minimum reflection loss (RL) value of −60.08 dB at the layer thickness of merely 1.44 mm and the widest effective absorption bandwidth (EAB, RL ≤ −10 dB) of 5.06 GHz at 1.64 mm with 30 wt% filler loading. This work provides a great reference for designing MOF-derived absorbers with high MA performance.
✓ 已验证
DOI
PubMed
高影响因子
Catalysis Science & Technology
·
2022
·Vol. 12
·期 11
·3670-3684
·
IF 6.177
Chunwang Lv,Mingjiang Hu,Tianhao Yuan,Liqiang Yan,Hongwei Chen
The objective of this work was to investigate and contrast the mechanism of different B-site dopants for catalytic activity and sulfur resistance under equivalent conditions. LaCo1−xMxO3 (M = Fe, Cr, Cu) perovskite-type catalysts were synthesized by a sol–gel method, and the optimized samples were tested for toluene oxidation before and after sulfur aging. The properties of the catalysts were investigated in detail by XRD, FT-IR, N2 adsorption–desorption, H2-TPR, XPS and in situ DRIFTS to elucidate the inner mechanisms of the catalytic reaction and poisoning processes. The results indicated that introducing specific metal cations with a suitable ratio into the B-site of perovskite could improve the catalytic activity and weaken the negative effect of SO2 poisoning. The reasons for the improvement of catalytic activity on different doped catalysts are similar and mainly lie in the change of reduction property, oxidation state of the B-site, and content of oxygen vacancies. However, the mechanism of sulfur resistance caused by different dopants is not identical. The introduction of different metal cations will cause certain differences in some factors such as reducibility, lattice stability, sulfur adsorption and sulfate content, thus leading to the differentiation of sulfur tolerance for doped perovskite catalysts. In this study, the optimization effect of Fe dopant is better than that of Cr and Cu dopants, illustrating that the high stability of the perovskite lattice and the insensitivity to sulfur species are the key factors for its outstanding sulfur resistance. The results provide insights into guiding the practical composition and life cycle optimization of perovskite-type catalysts in the industrial application of removing sulfur-containing VOCs.
✓ 已验证
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2022
·
IF 9.965
Dawei Liu,Katam Srinivas,Xin Chen,Fei Ma,Xiaojuan Zhang,Xinqiang Wang,Bin Wang,Yuanfu Chen
It is still challengeable but significant to rationally develop dual-metal single-atom catalysts with rich accessible active sites and excellent intrinsic catalytic activity towards oxygen reduction reaction (ORR). Herein, we present a novel dual-metal single-atom catalyst, Fe and Zn single atoms homogenously anchored on carbon nanotubes inlaid N, S-doped hollow carbon polyhedrons (FeZn-NSC), synthesized by facile iron-salt impregnation and high-temperature pyrolysis for zeolitic imidazolate framework-8. Due to the synergistic effects of the hierarchical porous nanoarchitecture with high specific surface area (795.48 m 2 g −1 ), N, S co-doped hollow carbon polyhedrons, in-situ grown highly conductive carbon nanotubes, and high loading of dual-metal single-atoms of Fe (3.12 wt%) and Zn (3.71 wt%), the optimized FeZn-NSC delivers outstanding ORR performance with high half-wave potential of 0.87 V, low Tafel slope of 44.7 mV dec −1 , long-term durability, and strong tolerance of methanol crossover. This work provides a strategy to rationally design and facilely synthesize dual-metal single-atom catalysts with high ORR activity.
✓ 已验证
DOI
PubMed
高影响因子
ACS Applied Materials & Interfaces
·
2023
·
IF 9.5
Qia Zhang,JianXiong Zou,Jin Ai,XiaoTian Pan,DongHong Qiao,Seong Chan Jun,Vijaykumar V. Jadhav,Ling Kang,Chun Huang,Jian Zhang
The current collector serves as a crucial element in supercapacitors, acting as a medium between the electrode material and the substrate. Due to its excellent conductivity, a metal collector is typically favored. Enhancing the binding strength between the collector and the substrate as well as between the collector and the electrode material has emerged as a critical factor for enhancing the capacitance performance. In this study, a Ag film with a grass root-like structure was initially grown on a PI substrate through the surface modification and ion exchange (SMIE) process. This Ag interlocking structure contributes to strong binding between the PI substrate and Ag without compromising the mechanical properties of the Ag film. To further enhance the electrochemical properties at low scan rates, electroless-plated Cu was subsequently deposited on the Ag film to form the Cu/Ag current collector. Moreover, the Cu within the Cu/Ag current collector served as a precursor for the growth of FeOOH–Cu(OH)2 via a two-step in situ method. The resulting FeOOH–Cu(OH)2/Cu/Ag structure as a whole is binder-free. Supercapacitors employing symmetric FeOOH–Cu(OH)2/Cu/Ag structures were assembled, and their energy storage properties were investigated. The solution-based low-temperature process used in this study offers the potential for cost-effective and large-scale applications.
✓ 已验证
DOI
PubMed
高影响因子