ENVIRONMENTAL SCIENCE & TECHNOLOGY
·
2021
·
IF 9.028
Fengping Zhou,Ye Xiao,Meina Guo,Yetao Tang,Weihua Zhang,Rongliang Qiu
The increasing demand for rare earth elements (REEs) motivates the development of novel strategies for cost-effective REE recovery from secondary sources, especially rare earth tailings. The biggest challenges in recovering REEs from ion-adsorption rare earth tailings are incomplete extraction of cerium (Ce) and the coleaching of iron (Fe) and manganese (Mn). Here, a synergistic process between reduction and stabilization was proposed by innovatively using elemental sulfur (S) as reductant for converting insoluble CeO2 into soluble Ce2(SO4)3 and transforming Fe and Mn oxides into inert FeFe2O4 and MnFe2O4 spinel minerals. After the calcination at 400 °C, 97.0% of Ce can be dissolved using a diluted sulfuric acid, along with only 3.67% of Fe and 23.3% of Mn leached out. Thermodynamic analysis reveals that CeO2 was indirectly reduced by the intermediates MnSO4 and FeS in the system. Density functional theory calculations indicated that Fe(II) and Mn(II) shared similar outer electron arrangements and coordination environments, favoring Mn(II) over Ce(III) as a replacement for Fe(II) in the FeO6 octahedral structure of FeFe2O4. Further investigation on the leaching process suggested that 0.5 mol L–1 H2SO4 is sufficient for the recovery of REEs (97.0%). This research provides a promising strategy to selectively recover REEs from mining tailings or secondary sources via controlling the mineral phase transformation.
✓ 已验证
DOI
PubMed
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2023
·
IF 15.1
Guiyuan Cai,Yu Tian,Lipin Li,Wenxuan Zhang,Rui Huang,Jun Zhang,Qinyu Wang,Hua Xu,Yifeng Zhang
The activation of sulfite [S(IV)] by transition metals, a new generation of advanced oxidation processes, has been widely studied for water purification. However, the application of this process to oxidize and remove arsenite [As(III)] from water through Fe-based S(IV) activation and the associated mechanisms are not fully understood. In particular, rapid removal of As(III) and secondary metal contamination have presented challenges. Herein, we develop a novel sea urchin-like magnetic Fe-Mn bimetallic oxides (FeMnO)-activated S(IV) process to address these issues. Under neutral pH, the FeMnO/S(IV) system achieved a 99.2 % removal of As(III) within only 10 min with residual arsenic concentration below 10 µg/L, and the removed As(III) was fully oxidized to arsenate [As(V)]. Additionally, FeMnO was recyclable and capable of treating actual arsenic-contaminated water. Furthermore, the oxidation mechanism of non-radical active trivalent manganese [Mn(III)] was discovered during the reaction between the FeMnO/S(IV) system and As(III). The FeMnO catalyst activated S(IV) to generate oxysulfur radicals (i.e., SO 5 •– , SO 4 •– and SO 3 •– ), but they were not the primary oxidizing species for As(III). Instead, As(III) oxidation was mainly attributed to the active Mn(III) generated by the electron transfer between the FeMnO catalyst and SO 5 •– radicals. The discovery of active Mn(III) species in this work may provide a new avenue for developing novel Fe-Mn-type adsorbents to purify arsenic-contaminated water.
✓ 已验证
DOI
高影响因子
FUEL PROCESSING TECHNOLOGY
·
2019
·
IF 4.507
Yinghui Sun,Guojie Zhang,Ying Xu,Yongfa Zhang,Yongkang Lv,Riguang Zhang
A series of Co-M (M = Ce, Fe, Zr) binary oxides supported on N-doped catalysts were prepared by impregnation methods and tested for DRM reaction. Moreover, the influence of Co and Ce atomic contents in the catalysts on DRM performance was investigated. Significant enhancement of activity performance over Ce promoted 3Co-1Ce/AC-N catalyst was observed. Compared with Fe and Zr, the catalyst with 1/4 mol% of Ce showed the highest activity and was higher than the supported Co catalyst . The calcined and spent catalysts were characterized by XPS , H 2 -TPR, TEM and EDX mapping studies. The characterization results demonstrated that the increase of 3Co-1Ce/AC-N reforming reactivity was attributed to the presence of Ce in Co-based catalyst, which modified the chemical states of Co-Ce composite oxide and redox properties, and increased the presence of Co 2+ species, the content of chemisorbed oxygen and the oxygen mobility. Among the different Co/Ce ratio catalysts, the one with a Co/Ce molar ratio at 1 exhibited better catalytic performance. As the Ce content increases, the content of chemisorbed oxygen was further decreased. In addition, the introduction of N on the support could also affect the catalyst reduction property and interaction of Co-Ce bimetal, which would improve catalytic performance.
✓ 已验证
DOI
高影响因子
JOURNAL OF ENVIRONMENTAL ENGINEERING
·
2025
·Vol. 151
·期 8
·04025043
·
IF 1.6
Jie Zhang,Mengchen Zong,Ben Dong,Sijie Ge,Shilong He
Quinoline, as one of the typical toxic and refractory organic pollutants in coal chemical industry wastewater, poses a significant threat to human health and environmental quality. In this study, MnCexOy and MnFexOy catalysts were successfully synthesized by doping Ce3+ and Fe2+ into α-MnO2 at a molar ratio of 1∶10 and were applied to the process of catalytic ozonation for the degradation of quinoline. Additionally, a variety of characterization techniques were employed to elucidate the characteristics of the catalysts, including scanning electron microscopy, X-ray diffraction, Brunauer–Emmett–Teller (BET) analysis, X-ray photoelectron spectroscopy, H2-TPR, NH3-TPD. The results show that, in the catalytic ozonation system for quinoline removal, MnCexOy demonstrates excellent quinoline removal efficiency of 87.45%, which is higher than that of MnFexOy (78.83%) and unmodified α-MnO2 (62.67%). By introducing the surface hydroxyl masking agent HPO42−, the significant role of surface hydroxyl groups and oxygen vacancies in the catalytic degradation of quinoline by MnCexOy was further demonstrated. Exploring the surface characteristics of catalysts is beneficial for continued understanding of the active centers of catalysts. Research results will be helpful to the deep treatment and reuse of tailing water of coking wastewater.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2025
·
IF 9.7
Min Xie,Xiaoying Li,Yufan Chen,Xiangyue Liao,Qiaoji Zheng,Heng Zhang,Kwok-Ho Lam,Dunmin Lin
Sodium superionic conductor (NASICON)-type phosphates cathodes have attracted considerable attention due to their high operational voltage and robust three-dimensional (3D) framework; however, the poor intrinsic electronic conductivity and low energy density hinder their broader application. Herein, a novel NASICON-type Na 3 V 1.44 Fe 0.5 Mo 0.06 (PO 4 ) 3 cathode was designed through Fe/Mo dual-doping at the V sites of Na 3 V 2 (PO 4 ) 3 and synthesized via a conventional high-temperature solid-state method. The introduction of Fe 3+ activates the V 4+ /V 5+ redox couple at a high voltage plateau (∼ 4.0 V), while also generates additional Fe 2+ /Fe 3+ and V 4+ /V 5+ redox pairs. Meanwhile, the doing of Mo 6+ creates cation vacancies, effectively modulating the electronic structure of vanadium and promoting ionic transport kinetics. Benefiting from this dual-doping strategy, the Na 3 V 1.44 Fe 0.5 Mo 0.06 (PO 4 ) 3 cathode delivers a high capacity of 123.4 mAh g −1 at 0.2C and an impressive energy density of 406 Wh kg −1 within 2.2–4.2 V. Moreover, it exhibits outstanding cycling stability, presenting a capacity retention of 92 % after 2500 cycles at 30C. This work highlights a viable strategy for advancing high-performance NASICON-type cathodes through complex metal ion doping.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2025
·
IF 9.7
Guo Liu,Shuhao Tian,Chang Li,Yizhi Li,Zhiming Deng,Zhijun Zou,Jiayou Tao,Kun Tao,Hongcen Yang,Xiaoxiang Sun,Fen Li,Erqing Xie,Zhenxing Zhang
Catalytic conversion of polysulfides is regarded as a crucial approach to overcome the chronic challenges from polysulfides shuttling and sluggish redox kinetics. Heterostructure catalysts can synergistically combine the advantages of each component with an interfacial built-in electric field (BIEF), demonstrating outstanding adsorption and catalytic effects. However, the relationship between surface electronic structure and interfacial charge redistribution remains unclear. Here, surface-oxidized MXene/α-Fe 2 O 3 (MXTiO/α-Fe 2 O 3 ) heterostructure is developed as model catalyst to clarify the enhancement mechanism of polysulfides adsorption and conversion. Theoretical and experimental analysis confirms that the modified MXene as an electron acceptor steals partial electrons from α-Fe 2 O 3 through interfacial asymmetric Ti-O-Fe bridge bonds, inducing the spontaneous charge redistribution. The electrons transfer through Ti-O-Fe channels creates electron-deficient Fe sites on the surface, which not only reduces the antibonding orbital electron occupation, leading to strengthening the d -p orbital hybridization between surface Fe and polysulfides, providing a strong sulfur affinity, but also weakens S S bonds for accelerated cleavage. The resulting catalyst enables Li-S batteries with a capacity of 538 mAh g −1 at 5.0C. This investigation establishes a fundamental correlation between interfacial electron delocalization and surface electronic configuration modulation, thereby providing a rational insight for designing advanced heterostructured electrocatalysts in high-performance energy storage/conversion applications.
✓ 已验证
产品关联
DOI
高影响因子
CARBON
·
2023
·
IF 10.9
Yujie Ren,Yinghan Zhang,Qi Zheng,Lianjun Wang,Wan Jiang
Porous Carbon-based composites with large specific surface area are promising as lightweight electromagnetic wave (EMW) absorbers due to their inherently rich interfaces that facilitate microwave attenuation. However, the exertion of the intrinsic advantage of large surface area was underexplored. Herein, we described a facile strategy using MOF-derived large surface area porous carbon to construct dielectric-magnetic composites for high-efficiency EMW absorbers. In particular, a series of Fe@C composites were fabricated by pyrolysis of MOF-5 to form porous carbon matrix (S BET ∼ 1800 m 2 /g), followed by ferrocene deposition and reduction. By altering Fe species amount, surface area and electromagnetic parameters of the composites were tuned. It is found Fe@C-0.6 composites with sufficiently high S BET ∼915.8 m 2 /g exhibited outstanding microwave absorption performance with the minimum reflection loss (RL min ) of −64.6 dB (1.98 mm thickness and 15 wt% loading) and the effective absorption bandwidth (EAB) up to 6.27 GHz (2.2 mm thickness). Besides, Fe@C-1 (S BET ∼820.1 m 2 /g) also achieved desirable loss capability, with EAB covering the whole Ku band . This work demonstrates the potential of high surface area to achieve optimal EMW attenuation, and may provide a facile alternative to develop more high-performance carbon composites for EMW absorption application.
✓ 已验证
DOI
高影响因子
ChemistrySelect
·
2025
·Vol. 10
·期 9
·e202405544
·
IF 2
KeXuan Wu,Ting Peng,Jing Cao
Graphical In this paper, a rod-like Fe and Bi co-doped Co 3 O 4 is prepared by hydrothermal method as an electrocatalyst for chlorine evolution reaction and ammonia nitrogen degradation. Compared to Co 3 O 4 , the doping of Fe and Bi can effectively improve the electrocatalytic performance, providing a new design idea for the construction of electrode materials with high activity and selectivity. Chlorine evolution reaction (CER) using dimensionally stable anode (DSA) materials are widely used in the chlor-alkali industry. However, they still have problems such as high preparation cost, limited selectivity, the titanium substrate being easy to passivate, [ 2 ] and the electrode active material being easy to dissolve. Co 3 O 4 , a nonprecious metal material, has shown good catalytic potential in promoting the CER reaction, which has broad application prospects as a CER electrocatalyst. In this paper, a highly regular Rod-like Fe, Bi co-doped Co 3 O 4 electrocatalyst was prepared. Compared with pure Co 3 O 4 , the material had a larger electrochemical-specific surface area, lower charge transfer resistance, and better catalytic performance. In a 0.6 M NaCl solution, at a current density of 20 mA/cm 2 , it achieves a current efficiency of 91.8% and degrades ammonia nitrogen with an efficiency of 82%.
✓ 已验证
产品关联
DOI
高影响因子
Energy Storage Materials
·
2025
·
IF 20.2
Nengbiao Zhang,Luming Yin,Letian Chen,Bingbing Ma,Yuantonghe Li,Xinyi Zhang,Junqing Liu,Zhen Zhou
Abstact Lithium-nitrogen (Li-N 2 ) battery is not only an electrochemical energy storage platform, but also an environmentally friendly nitrogen fixation technology. However, a great challenge remains in regulating catalyst activity to accelerate cathode reaction kinetics. Herein, we proposed an oxygen vacancy-mediated modulation of Fe active sites in FeO x nano-particle catalysts and Fe single-atom catalysts to enhance nitrogen reduction reaction in Li-N 2 batteries. High-concentration oxygen vacancy is generated through a size- and crystallinity-dependent oxygen vacancy engineering based on the precise atomic layer deposition of reducible oxides. The oxygen vacancy on FeO x drives the electron redistribution of Fe 3+ d-orbitals to provide electron-donating Fe active sites for N 2 fixation. Meanwhile, oxygen vacancy-rich MoO y is used as a support to anchor Fe single atoms. Adjacent oxygen vacancy drives the stable coordination between Fe single atoms and O atoms to facilitate the directional electron transfer from MoO y to Fe to N 2 . Therefore, the Li-N 2 batteries exhibit large discharge capacity, excellent rate performance, and reliable cycle stability. In addition, the formation and decomposition of the discharge product Li 3 N indicate a reversible N 2 fixation. This work provides a precise regulation mechanism of catalytic active sites based on oxygen vacancy engineering, which is expected to promote the development of high-performance Li-N 2 batteries.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Environmental Chemical Engineering
·
2024
·
IF 7.4
Yuqi Liu,Huanxin Zhao,Dan Wu,Xiaoyuan Shang,Mingyi Lv,Huixin Yu
Although single atom catalysts (SACs) have been recognized as a prospective catalyst in advanced oxidation processes (AOPs) via persulfate activation, they still confronted with the issues of metal atoms aggregation and limit loading amounts. For addressing these issues, single Co atoms that incorporated on Fe-Ni layered double hydroxides (FeNi-LDHs) with oxygen vacancies is fabricated. Employing it as the support of Co atoms can not only minimize the aggregation of single metal atoms but also conductive to increase their loading amounts (up to 3.26 wt%), which is expected to display an unprecedented catalytic activity. 100 % of TC (20 mg/L) can be eliminated within 5 min in Co-FeNi-LDH/PMS system. Radical and nonradical pathway collectively contributed to the TC elimination in Co-FeNi-LDH/PMS system, in which the electron transfer process in nonradical pathway is confirmed as the dominate mechanism via electrochemical studies and quenching experiments. PMS was adsorbed by Co-FeNi-LDH to form a Co-FeNi-LDH/PMS* complex during the PMS activation. Subsequently, TC is decomposed by transferring electrons to the Co-FeNi-LDH/PMS* complex via “donor-acceptor complex” mechanism. Benefiting from this mechanism, the Co-FeNi-LDH/PMS system displays superior anti-interference capability against inorganic anions. This study provides a unique insight on the skillful design and application of SACs.
✓ 已验证
产品关联
DOI
高影响因子
RARE METALS
·
2025
·
IF 11
Wei He-He,Zhang Xin-Xin,Sun Si-Wei,Gai Shi-Li,Yu Hai-Tao,Xie Ying
Transition metal phosphides (TMPs), with tunable electronic structures and diverse compositions, are promising candidates for electrocatalytic water splitting. However, their unsatisfactory electrical conductivity and tendency to aggregate during reactions result in structural instability, ultimately hindering further improvement of their electrocatalytic performance. To address these issues, a bamboo-leaf-like FeCoP/MXene heterojunction was synthesized by hydrothermal and thermal treatments, utilizing highly conductive MXene as the substrate. Density functional theory (DFT) calculations and experimental characterization reveal that strong Ti–O–Co/Fe covalent bond are formed between MXene and FeCoP through hybridization of O 2p and Co/Fe 3d orbitals, which enhance the structural stability of the interface and facilitate the effective anchoring of FeCoP on the MXene surface. Consequently, the structural stability and electrical conductivity of the catalyst are improved simultaneously. Additionally, interfacial charge redistribution optimizes the Gibbs free energy of hydrogen adsorption at the Co, Fe, and Ti sites while promoting the adsorption and activation of water molecules. These factors interact synergistically, leading to enhanced bi-functional electrocatalytic performance for both the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). In a FeCoP/MXene (+||−) two-electrode system, the catalyst achieves a current density of 10 mA cm –2 at a potential of 1.5 V, which is superior to the RuO 2 (+)||Pt/C (−) system. The assembled water splitting device exhibits long-term stability for up to 100 h at a current density of 100 mA cm –2 . Furthermore, an anion exchange membrane water electrolyzer (AEMWE) equipped with FeCoP/MXene as both anode and cathode achieves an industrial-grade current density of 500 mA cm –2 at 1.83 V. These results highlight the critical role of interfacial engineering in enhancing the electrocatalytic performance of TMPs for water splitting and provide valuable insights for the design of novel bifunctional TMP catalysts. Graphical abstract
✓ 已验证
产品关联
DOI
高影响因子
ANALYTICA CHIMICA ACTA
·
2025
·
IF 6
Jingzhi Zhou,Xichen Shi,Chaoqin He,Xiuwen Zheng,Ruo Yuan,Xia Yang
Background Entropy-Driven Circuits (EDC), distinguished by their spontaneous operation and absence of enzymatic reactions, represent a superior strategy for integration with CRISPR/Cas systems, as they obviate the potential for interference among various enzymes during the process of DNA amplification and CRISPR/Cas system integration. Due to the wide band gap of TiO 2 , its response to visible light is limited, and owing to its high crystallinity and exceptionally stable crystal lattice, the charge transfer (CT) process in TiO 2 is suboptimal. Results In this study, lychee-like Fe–TiO 2 was firstly prepared to serve as Raman enhanced substrate, facilitating exciton capture and separation to exhibit an excellent Surface-enhanced Raman spectroscopy (SERS) performance. It is proven that the incorporation of Fe results in a significantly narrower band gap for TiO 2 , facilitating exciton resonance. The amount of Fe in TiO 2 was optimized to fabricate a SERS biosensor for detection of miRNA-21 based on the Cas13a assisted entropy-driven system. The detection limit of miRNA was 43.88 fmol/L. Significance This work proposes a sensing strategy that integrates the CRISPR/Cas system with EDC, leveraging a semiconductor substrate exhibiting superior SERS performance to provide a stable Raman signal, thereby enabling highly sensitive detection of miRNA-21, which has a potential application in disease early warning and treatment.
✓ 已验证
产品关联
DOI
PubMed
高影响因子