Journal of CO2 Utilization
·
2018
·
IF 5.503
Zafar A.K. Khattak,Hussein A. Younus,Nazir Ahmad,Baoyi Yu,Habib Ullah,Suleman Suleman,Adeel H. Chughtai,Bibimaryam Moosavi,Chaemchuen Somboon,Francis Verpoort
Novel mono- and dinuclear dimethyltin(IV) complexes were synthesized using tridentate Schiff base ligands, derived from 2-amino-2-hydroxymethyl-propane-1,3-diol and various aldehydes. These diorganotin(IV) compounds displayed good catalytic activity for solvent-free cycloaddition of CO 2 to epoxides at ambient pressure. These catalysts efficiently completed the insertion of CO 2 to various epoxides at low catalyst loadings (0.1–1.0 mol%) in 1–6 hours giving high values of TONs around 1000. The catalyst further usability for three continuous reaction runs in the reaction mixture gives the same activity revealing the remarkable stability of these compounds under the given reaction conditions. Therefore, organotin(IV) complexes are efficient catalysts for the synthesis of the industrially important cyclic carbonates from epoxides at ambient pressure under solvent-free conditions.
研究领域:
无机化学
·
催化化学
·
绿色化学
·
二氧化碳利用
·
有机金属化学
✓ 已验证
DOI
高影响因子
JOURNAL OF MEMBRANE SCIENCE
·
2026
·
IF 9
Peng Li,De Ao,Zhenjie Gu,Zhihua Qiao,Chongli Zhong
Metal-organic framework (MOF)-based membranes show promising potential for gas separation. However, it remains challenging to fully exploit the synergistic advantages of MOF crystals and polymers for fabricating highly loaded mixed matrix membranes (MMMs). Herein, a highly loaded ZIF-8 ultrathin MMM was prepared in situ via a stepwise growth strategy. Driven by the diffusion rate difference between the ligand and polyethyleneimine (PEI-600), preferentially formed ZIF-8 crystals served as the dominant phase, while the subsequently developed PEI-Zn 2+ crosslinked network acted as an intergranular densification phase. Owing to the reduction in ZIF-8 crystal size induced by PEI, the MMMs exhibited an ultrathin thickness of only 160 nm. Furthermore, PEI enhanced the molecular sieving ability of crystals and membrane's CO 2 /N 2 solubility selectivity by regulating the pore structure and membrane composition. With a high ZIF-8 loading of 84.3 %, the resulting MMMs demonstrated an excellent CO 2 permeance of 3177.4 GPU, accompanied by a CO 2 /N 2 selectivity of 36.9. Notably, it maintained stable separation performance after bending and during long-term operation, showing good processability and industrial application potential. This strategy not only reinforces the advantages of MOF-based gas separation membranes but also provides a new paradigm for fabricating highly loaded MMMs.
✓ 已验证
产品关联
DOI
高影响因子
ACS Catalysis
·
2026
·
IF 13.1
Fengwang Zhao,Ting Zeng,Xiaoli Yang,Qi Wang,Yang Zhao,Jing Zhou,Xiaofeng Yang,Chunfu Lin,Haoxi Ben,Nianxue Zhai,Xianghui Yu,Youzhu Yuan,Xiang-Kui Gu,Xingyun Li,Yanqiang Huang,XiuSong Zhao
Catalyst structure manipulation at the atomic level is important in regulating the catalytic performance. Herein, single Cr atom doping in In2O3 is shown to modulate the In–O bond with improved performance in CO2 hydrogenation to methanol. An “asymmetric site effect” concept is proposed to interpret the function of Cr doping, wherein Cr stimulates directly coordinated oxygens to form Cr and In confined oxygen vacancies as active sites for enhancing CO2 activation and lowering the energy barrier of the HCOO* to HCOOH* transformation (the rate-determining step). Meanwhile, Cr assists in maintaining the structure stability and inhibits the over-reduction of In2O3 through tethering nearby oxygen atoms. Cr–In2O3 catalyst exhibits a CO2 conversion of 9.4% and CH3OH selectivity of 92.0% under reaction conditions of 250 °C and 5 MPa, along with a long-term stability over 500 h on-stream testing. This study demonstrates a paradigm for the modulation of In–O in In2O3 to break the trade-off between the reactivity and stability of the CO2 hydrogenation reaction.
✓ 已验证
产品关联
DOI
高影响因子
Nature Communications
·
2026
·
IF 15.7
Li Yukong,Wang Ziyi,He Xiaoyang,Sun Chen,Zheng Qikai,Jiang Yilin,Chen Zuofeng,Fei Honghan
Hybrid lead halides have demonstrated great promise for CO 2 photoreduction due to their excellent photophysical properties. However, developing a single-component hybrid lead halide that combines high intrinsic stability with near-infrared absorption remains a significant challenge. Herein, to address both issues, we design a series of nine highly stable lead halide frameworks functionalized by bis(terpyridine)-metal complexes, which exhibit strong light absorption extending into the near-infrared region up to 1150 nm. Unlike their symmetric chloride and bromide analogues, the charge-polarized lead iodide sites in bis(terpyridine)-metal-functionalized frameworks serve as highly efficient C–C coupling centers for C 2 production in near-infrared-driven CO 2 photoreduction, achieving notable C 2 production rates of up to 14.2 μ mol g -1 h -1 with electron selectivities as high as 86%. These performances match the state-of-the-art among all reported single-component, near-infrared-responsive photocatalysts. This work highlights the potential of coordination-driven assembly of highly stable lead halide frameworks for near-infrared-driven artificial photosynthesis.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2026
·
IF 9
Zhiyi Li,Xujia Mu,Wei Wei,Zhijun Liu
To overcome the limitations of conventional ionic liquid-based CO 2 absorbents—namely high regeneration energy consumption and low absorption capacity—a novel biphasic dual-functionalized ionic liquid system, [AEPH][Im]/NPA/H 2 O, was synthesized and evaluated. Initially homogeneous, the system undergoes spontaneous phase separation upon CO 2 absorption, forming distinct lean and rich phases. At saturation, the rich phase accounted for 53.00% of the total volume, with a viscosity of 15.75 mPa·s and a CO 2 loading capacity of 3.43 mol·L −1 . The system exhibited a high regeneration efficiency of 83.42% at 393.15 K, and the regenerated phases could be recombined into a uniform solution. After six absorption-desorption cycles, the absorbent retained 96.39% of its initial capacity, with only a 1.32% decline in desorption efficiency. The 13 C NMR analysis and DFT calculations revealed that CO 2 primarily reacts with [AEPH][Im] to form carbamate, carbonate, and bicarbonate species, which are predominantly concentrated in the rich phase, while only unreacted components remain in the lean phase. NPA facilitates the formation of alkyl carbonates via reaction with carbamates, and the high concentration of bicarbonate significantly enhanced desorption efficiency. The total regeneration energy consumption was calculated to be as low as 1.58 GJ·t −1 CO 2 —markedly lower than that of traditional MEA-based solvents. The [AEPH][Im]/NPA/H 2 O biphasic system demonstrates superior cyclic stability, high CO 2 capture capacity, and low energy demand, presenting a promising alternative for industrial-scale carbon capture applications.
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2026
·
IF 9
Ying Wang,Linlin Geng,Xiaoya Wang,Jianwen Wei,Xuecong Ma,Lei Liao
Amine-modified adsorbents exhibit remarkable potential for efficient CO 2 capture. In this study, a series of amine-based bifunctional solid adsorbents for CO 2 capture was synthesized via an impregnation method. Fe Zr cyanide frameworks were first functionalized with Pluronic F127, followed by the immobilization of diethanolamine (DEA) and tetraethylenepentamine (TEPA) at different loadings (20–40 wt%). Among the resulting materials, FZ(F)-D35% (DEA) and FZ(F)-T35% (TEPA), exhibited the maximum CO 2 adsorption capacity at 45 °C, reaching 1.846 and 2.377 mmol·g −1 . Compared with the unmodified material (FZ), which exhibits an adsorption capacity of 0.989 mmol/g, they increased by 47% and 59%, respectively. After 6 adsorption-desorption cycles, FZ(F)-D35% and FZ(F)-T35% still retained 93.4% and 95.2% of their original capacities, respectively, exhibiting excellent cycling stability. Kinetic analysis indicated that the adsorption process followed the Avrami model (R 2 = 0.999), suggesting a dual mechanism involving both physisorption and chemisorption. Infrared spectroscopy further confirmed the formation of carbamate and hydrogen bonding during the CO 2 adsorption, highlighting the critical synergistic role played by amine groups and hydroxyl groups in the CO 2 adsorption mechanism. It can therefore be inferred that the CO 2 adsorption mechanism is consistent with the zwitterion mechanism. These findings highlight the potential of amine-functionalized Fe Zr cyanide frameworks as robust, regenerable adsorbents for moderate-temperature CO 2 capture.
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Nano Materials
·
2026
·
IF 5.5
Yi Zheng,Shuaishuai Zhu,Keyi Liu,Zengneng Ma,Rong Ma,Jing Zhang,Chunlei Li
Poor adsorption and sulfate-induced high carrier recombination limit the CO2 photocatalytic reduction activity of TiO2 nanoparticles (anatase phase, average diameter ∼15 nm, and specific surface area 37.42 m2/g), as well as the generation of C–H added-value compounds. In this work, the difficulty of generating CH4 by photoreduction of CO2 on TiO2 was solved by constructing a composite of porous nitrogen-doped activated carbon (p-CN-2) with hierarchical nanochannels (5–20 nm), nanopores (<5 nm), and TiO2 nanoparticles. The introduction of p-CN-2 promoted the adsorption of CO2 and proton generation. Meanwhile, pyridine N in p-CN-2 interacts with TiO2 to establish a Ti–N–C photocarrier separation channel to enhance the effective photogenerated charge density. Promoted CO2, protons, and photocarrier concentrations modulate the occurrence of photocatalytic CO2 methanation on TiO2. The CH4 4 h yield of TiO2/p-CN-2 is 47.12 μmol·g–1, which is about 50 times higher than that of TiO2. The CH4 selectivity of TiO2/p-CN-2 increases from 15.53% TiO2 to 82.05%. This work presents a facile and effective method for facilitating photocatalytic CO2 methanation using TiO2 as a model. This work presents a facile and effective method for facilitating photocatalytic CO2 methanation using TiO2 nanoparticles as a model, and the prepared TiO2/p-CN-2 nanocomposite is particularly well-suited for solar-driven CO2 methanation in carbon recycling systems and renewable energy production (e.g., coupling with photovoltaic devices for green CH4 fuel synthesis).
✓ 已验证
产品关联
DOI
高影响因子
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2026
·
IF 3.9
Mengyu Wang,Shuhan Zhang,Chaoyue Meng,Fenglei Han
To enhance the conversion efficiency and product selectivity in CO2 hydrogenation to methanol, we prepared a series of Cu–Fe bimetallic catalysts with varied Cu/Fe ratios supported on HZSM-5 by an initial impregnation method and evaluated them in a dielectric barrier discharge (DBD) nonthermal plasma reactor. Among these, the Cu7Fe3/HZSM-5 catalyst achieved a CO2 conversion of 12.1% and a methanol selectivity of 9.6% in plasma-assisted CO2 hydrogenation, with activity decay below 3% over 400 min of continuous operation. The catalyst structure and surface properties were systematically investigated by SEM, XRD, BET, XPS, H2-TPR, CO2-TPD and CO-TPD. Catalytic performance was assessed under optimized plasma reaction conditions (CO2/H2 = 1:3, total flow 70 mL·min–1, discharge power 20 W, circulating water temperature 30 °C). Furthermore, in situ DRIFTS indicated an oxygen vacancy-dominated formate pathway: oxygen vacancies in FeOx strengthened CO2 chemisorption and induced polarization of the C═O bond; Cu+ sites facilitated sequential hydrogenation of formate intermediates (HCOO*); and the Cu0-HZSM-5 interface optimized H* spillover, collectively suppressing CH4 formation. These results underscore that vacancy engineering and metal–zeolite interfacial effects are pivotal in steering plasma-catalytic CO2-to-methanol selectivity.
✓ 已验证
产品关联
DOI
高影响因子
Science China-Chemistry
·
2026
·
IF 9.7
Wang Yuchen,Shi Wenjie,Lu Tongbu,Zhong Dichang
Metal-coordinated covalent organic frameworks have attracted extensive attention in the field of CO 2 photoreduction to CO due to their high electron affinity and tunable structure. However, achieving efficient CO 2 activation requires overcoming the challenges of multi-electron transfer and intermediate stabilization, necessitating multifactorial optimization such as metal site cooperation, photosensitizer anchoring, and spatial alignment. Herein, we designed and fabricated a hydroxyl-functionalized COF featuring dinuclear Co/Zn sites and incorporated [Ru(phen) 3 ](PF 6 ) 2 as the photosensitizer for photocatalytic reduction of CO 2 to CO. When the ratio of Co(II) and Zn(II) in the dinuclear COF was 1:2, the obtained isostructural COF-Co 1 Zn 2 showed enhanced CO production, with the CO conversion rate reached 46062 µmol g
−1 Co
h −1 , which was three times higher than the CO production of the single metal COF (COF-Co: 15309 µmol g
−1 Co
h −1 ). DFT calculation and photoelectrochemical results supported the enhanced photocatalytic CO 2 reduction performance of COF-Co 1 Zn 2 . This work shows that multi-site synergistic catalysis is an effective way to optimize the catalytic performance of COF catalysts for photochemical CO 2 reduction.
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 13.2
Menghuan Wu,Yifang Zhang,Zhiping Xu,Yuqi He,Jialei Wang,Tian Xie,Shuduan Deng,Lidan Zhang,Gang Zhu
Metal–organic frameworks often lose CO 2 capacity in hot, humid flue gas because H 2 O competes for open metal sites (OMSs). Here we report a dual-stabilized, wood-based adsorbent in which Mg-MOF-74 is grown on an aminated wood sponge and overcoated with an ultrathin polydimethylsiloxane (PDMS) layer, coupling support immobilization with interfacial hydrophobization while preserving access to OMSs. Under flue-gas-relevant conditions (323 K, 50% RH), the material delivers a CO 2 uptake of 1.68 mmol·g −1 (≈89% of its dry-state capacity) and an IAST CO 2 /N 2 selectivity of 144 for a 50/50 mixture at 323 K. Humid-gas breakthrough tests confirm robust separation performance. Density functional theory (DFT) calculations attribute the humidity tolerance and selectivity to the synergy between accessible OMSs and PDMS-mediated interfacial polarity, without increasing the isosteric heat of adsorption, thereby enabling energy-efficient regeneration. The framework retains its crystallinity after 30 days of water immersion, and a techno-economic estimate projects a material cost of approximately US$10.36 kg −1 at a 1000 t·yr −1 scale. This scalable architecture reconciles capacity, selectivity, humidity resistance, and cost for post-combustion CO 2 capture.
✓ 已验证
产品关联
DOI
高影响因子
Journal of CO2 Utilization
·
2026
·
IF 8.4
Zhilei Dai,Jing Zhang,Yiling Tong,Ning Zhou,Songyao Liu,Zhifeng Dai,Yubing Xiong
The efficient conversion of atmospheric CO 2 into high value-added chemicals remains a persistent challenge. In this study, a heterogeneous catalyst PD x BpyOH with both metal-free and halogen-free properties and nucleophilic hydroxyl sites was developed for the cycloaddition reaction of CO 2 with epoxides. This catalyst was constructed by incorporating a bipyridine complex and a imidazolium salt into an organic polymer matrix, followed by anion exchange. The porosity structure of these catalysts were optimized by tuning the crosslinker DVB ratio (x = 0, 2, 3, 4). A series of characterizations confirmed that it had a hierarchical micro-mesoporous structure, and the specific surface area regulated by DVB improved the physical adsorption capacity of CO 2 . Under the optimal conditions (80 mg catalyst, 60 °C, 1 atm CO 2 , 48 h), PD 2 BpyOH achieved 89 % conversion of epichlorohydrin. Furthermore, it maintained 85 % conversion in 96 h under simulated industrial flue gas (15 % CO 2 /85 % N 2 ), demonstrating robust recyclability and activity for various epoxides. This catalytic system provides a new metal-free and halogen-free heterogeneous catalytic strategy for the utilization of low-concentration CO 2 .
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 12.5
Zixuan Hao,Liju Bai,Shuai Wang,Kaiqing Sun,Yali Yao,Helei Liu
Conventional CO 2 capture methods, such as amine-based absorption, are hindered by solvent degradation, and corrosion issues, while solid adsorbents often suffer from limited adsorption capacity under flue gas conditions. To address these challenges, ionic liquids (ILs)-modified materials have emerged as promising alternatives due to their high efficiency, tunability, and environmental compatibility. Herein, using Lys as the anion, DETA, TETA, and TEPA were respectively combined to synthesize ILs with different chain lengths using one-step synthesis. These ILs were then loaded onto the mesoporous silica C803 carrier by impregnation. Characterization results indicate uniform distribution of ILs within the carrier without disruption of its mesoporous structure. At 298 K and 0.1Mpa, 66 wt% [TETA][Lys]-C803 exhibited the highest CO 2 adsorption capacity (2.51 mmol/g), representing 700% increase compared to C803, which was capacity further increased to 2.82 mmol/g at 308 K and 0.1Mpa. The material exhibited an excellent IAST-predicted CO 2 /N 2 selectivity of up to 200.17 for a 15/85 CO 2 /N 2 mixture, rapid adsorption kinetics (95% equilibrium in 6 min), and stable recyclability (unchanged performance after five cycles). Combined FTIR and DFT analyses revealed that lysine anions stabilize products and zwitterionic intermediates via electrostatic networks, thus enhancing CO 2 amine binding energy remarkably. The study further provides a novel strategy and theoretical basis for developing high-performance, renewable CO 2 capture materials for flue gas.
✓ 已验证
产品关联
DOI
高影响因子