CHEMICAL ENGINEERING JOURNAL
·
2020
·
IF 10.652
Yongkui Li,Xianjin Qi,Guohua Li,Hua Wang
Nonferrous smelting wastewaters containing high levels of arsenic and sulfuric acid threaten human health and ecological environments due to insufficient disposal technologies and/or possible leakages during transportation to long-term storage facilities. Chemical precipitation is one important route for arsenic removal and immobilization via the formation of arsenic-stabilized minerals. In this study, we propose a new strategy for the treatment of wastewaters containing high levels of arsenic using pyrite as an in situ S and Fe source to prepare environmentally friendly scorodite and As 2 S 3 precipitates. Dissolved pyrite release (S-II) and Fe (II) ions in highly acidic wastewater, both of which drive arsenic precipitation. Sulfide ions readily react with As(III) to generate the stable As 2 S 3 while Fe(II)/As(III) were oxidized to Fe(III)/As(V) by H 2 O 2 . The reaction between Fe(III) and As(V) took place on the pyrite surface as a nucleation site to form amorphous ferric arsenate that ultimately transformed into crystalline scorodite. Sulfide ions were oxidized to H 2 SO 4 that further promoted pyrite dissolution. Up to 99.4% of arsenic was successfully removed from copper smelting wastewaters with an initial arsenic concentration of 11200 mg/L. The concentration of leached As from the As-bearing precipitate was 1.78 mg/L under optimized conditions, which were: a 1.4 FeS 2 /As molar ratio, an initial solution pH of 2, an H 2 O 2 /As molar ratio of 1%, a reaction temperature of 90 °C, and a reaction time of 12 h. In summary, a prospective process successfully shows arsenic removal and immobilization from smelting wastewater, and further demonstrates the potential for the efficient and affordable disposal of wastewater.
✓ 已验证
产品关联
DOI
高影响因子
Molecular Catalysis
·
2020
·
IF 3.687
Yang Zhong,Bo Zhou,Lijun Wang
Fe/FeO x embedded in LDH was prepared by reducing the pre-synthesized [Fe(C 2 O 4 ) 3 ] 3− anions intercalated LDH and used as a multi-functional catalyst for synthesis of C7-C9 compound via transfer hydrogenation between furfural (C5) and short-chain alcohols (C2-C4) and a subsequent aldol reaction of furfural with intermediate short-chain aldehydes in the absence of a homogeneous base with furfuryl alcohol as a byproduct. Screening reaction conditions, evaluation and improvement of the cyclic catalytic performance, and determination of catalytically active components were performed, and the results demonstrated that both high conversion and high selectivity to the C C bond forming product can be obtained under a non-oxidizing atmosphere of Ar or H 2 /Ar mixed gas, a reaction temperature of 140 °C and a reaction time of 4 h; the catalyst was easily deactivated during the cycle experiments, however, its catalytic stability can be effectively improved by depositing Ni with weak reducibility on the surface of Fe nanoparticles at the cost of reducing partial catalytic activity. Fe/FeO x together with LDH as a whole proved to be effective in catalyzing the transfer hydrogenation reaction and the support LDH imparted basic catalytic function to the composite realizing the aldol reaction in the absence of a homogeneous base.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Energy Chemistry
·
2020
·
IF 7.216
Yan Lin,Kaian Sun,Xiaomeng Chen,Chen Chen,Yuan Pan,Xiyou Li,Jun Zhang
The hydrogen evolution reaction (HER) via water electrolysis has gained immense research attention. Seawater electrolysis provides great opportunities for sustainable energy production, but is extremely challenging. Transition metal phosphides are promising candidate electrocatalysts. Herein, we prepared a novel Fe–Co 2 P bundle of nanorods (BNRs) for catalyzing the HER in seawater electrolysis and over the entire pH range. Cobalt phosphides with different crystal phases and morphologies were obtained by varying the Fe doping amount. The Co:Fe molar ratio of 1:0.5 was found to be optimum. The Fe doping improved the HER performance of Co 2 P over the entire pH range by providing favorable electronic properties and morphology, lattice distortion, and special coordination environment. The Fe-Co 2 P BNRs showed higher catalytic activity than 20% Pt/C in seawater at high potentials. The density functional theory calculations revealed that the Fe doping reduced the hydrogen binding strength of Co 2 P to efficiently accelerate the HER kinetics and produce a favorable charge density. This study provides valuable insights into the design and development of high-efficiency HER catalysts for large-scale seawater electrolysis.
✓ 已验证
产品关联
DOI
高影响因子
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2020
·
IF 3.573
Xing-Zhe Guo,Shuai-Shuai Han,Ji-Min Yang,Xiao-Meng Wang,Shui-Sheng Chen,Shuai Quan
We herein report that the morphology, size, and surface charge status of MIL-100(Fe) micro/nanoparticles can be tailored by adding a coordination modulator (HF or tetramethylammonium hydroxide) to the reaction system. Interestingly, the adsorption capacities of low-crystallinity MIL-100(Fe) and MIL-100(Fe)-TMA toward Congo red (CR) and acid chrome blue K (AC) were found to be significantly larger than that of the high-crystallinity MIL-100(Fe)-HF adsorbent, whereas there was little difference in the adsorption capacities of the three MIL-100(Fe) toward methyl orange (MO) and methylene blue (MB). The adsorption uptake of MIL-100-(Fe)-TMA toward the anionic dyes (CR, AC, and MO) was found to be highest, whereas the adsorption uptake of MIL-100(Fe) toward the cationic dye (MB) was the highest owing to different adsorption mechanisms. This adsorption behavior could be rationalized based on the morphological characteristics and crystal structure defects, zeta potential, and pore volume of MIL-100(Fe) and the adsorption characteristics and molecular structure of the dye. It was revealed that the adsorption performance of MIL-100(Fe) micro/nanoparticles is governed by the synergistic interplay between electrostatic, hydrophobic, and π–π stacking interactions, pore volume, crystal structure defects, and steric hindrance of the adsorbent.
✓ 已验证
产品关联
DOI
高影响因子
IONICS
·
2021
·Vol. 27
·期 12
·5287-5295
·
IF 2.817
Cong Yuanyuan,Xie Guihui,Meng Xiangzhi,Wang Haibin,Meng Fanchao,Li Chunlei,Zhao Qiuping
Fabrication of an advanced electrocatalyst for oxygen reduction reaction (ORR) is important for the commercialization of fuel cells. Herein, we report an ORR electrocatalyst with Fe atoms evenly distributed on crumple-rich nitrogen-doped carbon (N–C) nanospheres via a simple melamine-assisted pyrolysis strategy, where crumple-rich N–C nanospheres are prepared by a dual soft template approach. The as-obtained Fe–N-C-M electrocatalyst shows a better onset potential (1.02 V vs. RHE) and half-wave potential (0.883 V vs. RHE) in alkaline solution, superior to the commercial Pt/C (0.97 and 0.860 V vs. RHE, respectively). Moreover, the Fe–N-C-M also displays outstanding stability with 80.4% of relative current remained after a 10-h stability test at 0.8 V vs. RHE and remarkable methanol tolerance with 79.2% of relative current sustained after adding 3 M methanol, outperforming the commercial Pt/C (49.4% and 48.5%, respectively). All of these excellent properties are contributed to the unique crumple-rich structure, large specific surface area, and high content of Fe-N x and pyridinic-N active centers.
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2021
·
IF 5.816
Hui Wang,Lei Lu,Palaniappan Subramanian,Shan Ji,Palanisamy Kannan
Developing a highly active, low-cost, and durable nanostructured catalytic material is of significant interest in fuel cell applications owing to its efficient energy conversion, ease of preparation and operation, and reduced emission of pollutants. In this work, various ratio (0.01, 0.03, and 0.05 mmol) of cobalt (Co), and iron (Fe) doped nickel hydroxide (Ni(OH) 2 ) nanosheet arrays were grown on Ni foam surface (Co–Ni(OH) 2 and Fe–Ni(OH) 2 ) via a simple one-step process. The Co–Ni(OH) 2 and Fe–Ni(OH) 2 nanosheet array on Ni foam electrodes were explored as potential candidate towards electro-oxidation of urea. Notably, 0.03 mmol Co doped Ni(OH) 2 /Ni foam electrode displayed lowest-onset oxidation potential (0.21 V) and enhanced electro-oxidation of urea (59.7 mA) owing to its large amount of electrocatalytic active sites, densely assembled nanosheet array structures with porous surfaces, and electronic diffusion channels, which might promote interface electrochemical reaction . In addition, synergistic effect between Co metal with Ni(OH) 2 has also promotes enhanced electro-oxidation of urea in contrast to Fe–Ni(OH) 2 nanosheet array, Ni(OH) 2 , and Ni foam electrodes. Chronoamperometric i-t curve of Co–Ni(OH) 2 /Ni foam electrode obviously exhibited higher catalytic current, highly stable and durable properties in contrast to Fe–Ni(OH) 2 nanosheet arrays. As-fabricated Co–Ni(OH) 2 /Ni foam can be explored as a new type of potential low-cost catalyst for electro-oxidation of urea, which reveals promising use in future fuel cell energy applications .
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2021
·
IF 13.273
Hui He,Yuexin Wang,Juan Li,Shanliang Jiang,Subhan Sidra,Wenxue Gong,Ying Tang,Yang Hu,Rule Wei,Dongxiao Yang,Xuesheng Li,Zhongxing Zhao
High light adsorption and fast charge separation are crucial for photo-Fenton catalytic activity of MOFs. Herein, bottom-up design was proposed to fabricate polypyrrole (PPy C ) nanowires in MIL-88B(Fe) cages as photo-Fenton catalyst for Sulfamethoxazole (SMX) efficient degradation. Pyrrole was prior anchored into MIL-88B(Fe) cluster via Fe-N coordination, and then the additional monomer pyrrole was further triggered bottom-up polymerization in confined cages of MIL-88B(Fe) and formed PPy C @Py-MIL(Fe) composite. These PPy C nanowires were dispersed in Py-MIL(Fe) cages and tightly connected with MOFs clusters via Fe-N bonding. Characterization proved that: (1) Interfacial Fe-N can significantly promote the efficient electron transport from PPy C nanowires to Py-MIL(Fe), enhance optical absorption property, and construct strong Lewis acidic sites and ligand vacancies in PPy C @Py-MIL(Fe). (2) The confined PPy C nanowire via Fe-N connection remarkably promote photo-generated electron-hole separation, Fe 2+ |Fe 3+ redox ability of MOF, and improved photo-electric corrosion ability. As a result, it significantly enhanced the photo-Fenton catalytic performance for SMX degradation. Catalytic oxidation was attributed to the generation of ‧OH species that oxidized 93% SMX in 60 min, showing ultra-rapid degradation and TOC removal rates of 33.7 min −1 ·mg·g −1 and 8.68 min −1 ·mg·g −1 respectively, which was about 4–220 times higher than those reported state-of-the-art catalysts. Additionally, the PPy C @Py-MIL(Fe) catalyst showed minimal loss in catalytic activity even after recycling for 10 times, exhibiting good recycling stability compared to many MOFs. Systematic analysis shown that in-situ anchored growth of polypyrrole in confined porous cages of MOF can effectively enhance the catalytic activity and stability of MIL-88B(Fe), and has great development potential applications for photo-Fenton catalytic degradation of organic pollutants.
✓ 已验证
产品关联
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2021
·
IF 6.707
Zhaode Mu,Jiangman Tian,Jie Wang,Jing Zhou,Lijuan Bai
Sensitive detection of endotoxin is especially critical in the fields of food security, therapeutics and medical science. In this work, a new sandwich-type electrochemical aptasensor was designed for ultrasensitive detection of endotoxin. For the first time, nitrogen-doped carbon nanotubes (N-CNTs) was functionalized with polydiallyldimethylammonium chloride (PDDA), forming P-N-CNTs nanocomposite. Then, Fe-based metal–organic framework (Fe-MOF) and silver nanoparticles (AgNPs) was decorated with P-N-CNTs to form the MOF/Ag-P-N-CNTs nanohybrid, which was employed as an enhanced signal indicator, not only exhibited outstanding electrochemical activity, but also could directly label with thiol-modified signal probes (TSPs) to form tracer label. Additionally, the avidin–biotin recognition system was introduced to increase the amount of biotin-modified capture probes (BCPs). Differential pulse voltammetry (DPV) was utilized to investigate the detection performances of the proposed aptasensor, which suggested a wide linear range from 1 fg/mL to 100 ng/mL with a low detection limit of 0.55 fg/mL toward endotoxin.
✓ 已验证
产品关联
DOI
高影响因子
APPLIED CATALYSIS B-ENVIRONMENTAL
·
2021
·
IF 19.503
Jie Sun,Weiqi Gao,Honghan Fei,Guohua Zhao
Selective electrocatalytic conversion of NO 3 – to N 2 is an environmental-friendly strategy to close the anthropogenic nitrogen-based cycle. This work reported a metal-organic framework-derived electrocatalyst with earth-abundant bimetallic sites, showing quantitative (~97.9% conversion) and selective (~99.3%) nitrate-to-N 2 transformation. More importantly, both post-catalysis concentrations of NO 3 – and NO 2 – meet the drinking water limit requirements, set by World Health Organization. The reaction intermediates and mechanistic pathways in electrocatalytic reduction of NO 3 – to N 2 are elucidated by a variety of in-situ experimental studies and DFT calculations. The enhanced and selective electrocatalytic performances are ascribed to the relay catalytic effects of the neighboring Fe-Ni catalytic sites residing in the porous carbon electrocatalysts, which are structurally determined by X-ray absorption spectroscopy (XAS) as well as calculated structural model, with Fe sites decreasing the reaction barrier for NO 3 – conversion and Ni centers facilitating the adsorption and activation of reaction intermediates (NO 2 – , NO* and N 2 O*).
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS
·
2019
·
IF 3.47
Zhi Zheng,Jun Wang,Yi Wei,Xuejun Liu,Fengwen Yu,Jianbing Ji
La-Fe modified Si-MCM-41 (La-Fe/Si-MCM-41) catalysts were prepared by the wet impregnation method and used in catalytic cracking of soybean oil (CCS) for biofuel production. The catalysts were characterized by BET, XRD, XPS, Py-FTIR and CO 2 -TPD. The results showed that the aromatics content increased with the increase in B/L value, while the content of oxygenated compounds decreased, indicating that Brönsted acid sites were the major active sites for deoxygenation and aromatization reactions. Compared with Si-MCM-41, the Brönsted acidity of LFM-6 sharply decreased from 22.49 to 5.86 μmol g −1 . Accordingly, the aromatics content was reduced from 37.51 wt.% to 14.52 wt.% which was lower than the limitation (15 wt.%) according to the global environmental legislation. However, for the LFM-6 catalyst, the excessive loss of Brönsted acid sites and sharp decrease in BET surface area and pore volume led to the decrease in deoxygenation. As a result, the fatty acids content increased from 2.71 wt.% to 16.67 wt.% and the acid value reached 35.20 mgKOH g −1 . When the La-Fe loading increased to 15 wt.%, part of fatty acids were converted into ketones by the active sites on Fe 2 O 3 /La 2 O 3 and strong Lewis acid sites on catalysts. Besides, the new weak Lewis acid and basic sites on Fe 2 O 3 /La 2 O 3 exhibited the synergistic effect on promoting the generation of alkenes. The CaO/LFM-6 composite catalysts prepared by the mechanical mixing of LFM-6 and CaO were used in CCS to reduce the acid value of biofuel. LFM-6-C-3 was proved to be an effective catalyst for CCS to produce biofuel with low aromatics (12.31 wt.%) and fatty acids (2.76 wt.%) content.
✓ 已验证
产品关联
DOI
高影响因子
Scientific Reports
·
2019
·Vol. 9
·期 1
·1-11
·
IF 4.011
Khan Karim,Tareen Ayesha Khan,Aslam Muhammad,Ali Khan Sayed,khan Qasim,Khan Qudrat Ullah,Saeed Muhammad,Siddique Saleemi Awais,Kiani Maryam,Ouyang Zhengbiao,Zhang Han,Guo Zhongyi
Since the last decades, non-precious metal catalysts (NPMC), especially iron based electrocatalysts show sufficient activity, potentially applicant in oxygen reduction reaction (ORR), however they only withstand considerable current densities at low operating potentials. On the other hand iron based electrocatalysts are not stable at elevated cathode potentials, which is essential for high energy competence, and its remains difficult to deal. Therefore, via this research a simple approach is demonstrated that allows synthesis of nanosize Fe-doped mayenite electride, [Ca 24 Al 28 O 64 ] 4+ ·(e − ) 4 (can also write as, C 12 A 7−x Fe x :e − , where doping level, x = 1) (thereafter, Fe-doped C12A7:e − ), consist of abundantly available elements with gram level powder material production, based on simple citrate sol-gel method. The maximum achieved conductivity of this first time synthesized Fe-doped C12A7:e − composite materials was 249 S/cm. Consequently, Fe-doped C12A7:e − composite is cost-effective, more active and highly durable precious-metal free electrocatalyst, with 1.03 V onset potential, 0.89 V (RHE) half-wave potential, and ~5.9 mA/cm 2 current density, which is higher than benchmark 20% Pt/C (5.65 mA/cm 2 , and 0.84 V). The Fe-doped C12A7:e − has also higher selectivity for desired 4e − pathway, and more stable than 20 wt% Pt/C electrode with higher immunity towards methanol poisoning. Fe-doped C12A7:e − loses was almost zero of its original activity after passing 11 h compared to the absence of methanol case, indicates that to introduce methanol has almost negligible consequence for ORR performance, which makes it highly desirable, precious-metal free electrocatalyst in ORR. This is primarily described due to coexistence of Fe-doped C12A7:e − related active sites with reduced graphene oxide (rGO) with pyridinic-nitrogen, and their strong coupling consequence along their porous morphology textures. These textures assist rapid diffusion of molecules to catalyst active sites quickly. In real system maximum power densities reached to 243 and 275 mW/cm 2 for Pt/C and Fe-doped C12A7:e − composite, respectively.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
SOLID STATE SCIENCES
·
2020
·
IF 2.434
Xiaofang Li,Yuandong Wu,Dajiang Mei,Hagen Poddig,Thomas Doert
Three hexasodium transition metal sulfates, Na 6 M (SO 4 ) 4 ·2H 2 O ( M = Fe, Co, Ni) were obtained by a dissolution and precipitation route and by hydrothermal reactions . The compounds were characterized by single crystal X-ray diffractions, UV/vis and IR spectroscopy , thermal analyses, and magnetization measurements. The title compounds all crystallize in the triclinic space group P 1 ‾ (No. 2) with Z = 1 and lattice parameters : a = 6.0679(8), b = 6.8658(8), c = 10.1508(12) Å, β = 92.557(4)° for Na 6 Fe(SO 4 ) 4 ·2H 2 O; a = 6.0595(5), b = 6.8446(6), c = 10.1149(8), β = 92.548(2)° for Na 6 Co(SO 4 ) 4 ·2H 2 O; a = 6.0490(4), b = 6.8265(5), c = 10.0793(7), β = 92.5470(10)° for Na 6 Ni(SO 4 ) 4 ·2H 2 O, respectively. [M(SO 4 ) 4 ] 6- anions are interconnected by hydrogen bonds to form two-dimensional layers in these structures. The solid-state UV/vis/NIR diffuse reflectance spectroscopy indicates that Na 6 M (SO 4 ) 4 ·2H 2 O ( M = Co, Ni) are insulators. Magnetization experiments show a nearly linear temperature dependence of the inverse susceptibility down to 2 K, which indicates a paramagnetic behavior for all three compounds.
✓ 已验证
产品关联
DOI
高影响因子