SEPARATION AND PURIFICATION TECHNOLOGY
·
2017
·
IF 3.359
Hongguo Zhang,Ting Li,Zhiquan Yang,Minhua Su,Lian Hou,Diyun Chen,Dinggui Luo
Perchlorate (ClO 4 − ) had caused great impacts to human health via inhibiting the uptake of iodide by the thyroid gland and its removal was strongly affected by co-existing anions in aqueous solution. The adsorptive features of perchlorate, co-existing anions and their removal mechanisms on two different metal-organic frameworks (MOFs) are compared in this paper. Two MOFs (i.e., α , β -ethanebbbdisulfonic-Cu-(4,4′-bipy) 2 and sulfamic-Cu-(4,4′-bipy) 2 ) were synthesized to remove ClO 4 − and co-existing anions from aqueous solution. It was found that MOFs can effectively remove PO 4 3− and ClO 4 − . The adsorption reactions of PO 4 3− and ClO 4 − by MOFs were exothermic and spontaneous, as confirmed by the thermodynamic analysis. The sorption rates of the anionic pollutants followed the pseudo first-order reaction. The sorption isotherms followed the Langmuir model with K L values of 0.0083, 0.0257, 0.2133 and 0.0448 for ClO 4 − , PO 4 3− , ClO 4 − (PO 4 3− ), PO 4 3− (ClO 4 − ), respectively. A certain amount of perchlorate and phosphate were adsorbed by MOFs under the pH range of 2 to 10. However, as long as pH increased up to 12, the absorption capability decreased remarkably due to the crystal structure of materials being collapsed in an alkaline environment. For the absorption of anions by MOFs, Gibbs’ free energy of may be attributed to the effects of adsorption. Sulfonic acid groups interlaminated in MOFs were exchanged by tetrahedral oxoanions, contributing to ion-exchange adsorption. The findings in this study help develop novel methods for perchlorate and phosphate removal from aqueous solution.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Inorganic and Organometallic Polymers and Materials
·
2016
·Vol. 26
·期 5
·1101-1106
·
IF 1.308
Wang Xiaoshuo Wu Pengfei,Lu Siyuan Xu Pengpeng
A new copper coordination polymer, [Cu 2 L 4 (H 2 O) 2 ] n ( 1 ), (HL = 3-(pyridine-2-yl)benzoic acid) has been solvothermally synthesized by using the HL and CuCl 2 ⋅2H 2 O and characterized by IR spectra, elemental analysis, single-crystal and powder X-ray diffractions, and TGA. Compound 1 contains a well-known paddle-wheel unit [Cu 2 (COO) 4 ], which is connected to a three-dimensional supramolecular structure with pcu topology through the hydrogen bond interactions. Compound 1 displays considerable thermal stability and exhibits selective absorption in the visible region, which is shown by thermogravimetric analysis and solid-state UV–Vis diffuse-reflectance spectra, respectively. In addition, compound 1 represents an example of visible light driven photocatalyst based on coordination polymer and shows good degradation ability over Rhodamine B (RhB).
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF INDUSTRIAL AND ENGINEERING CHEMISTRY
·
2017
·
IF 4.421
Hengjia Zhu,Jianming Pan,Jun Cao,Yue Ma,Fengxian Qiu,Wenli Zhang,Yongsheng Yan
Herein we reported a facile method to prepare porous ion/molecule imprinted polymers (I-MIPs) via twice imprinting strategy for the simultaneous uptake of copper ions (Cu(II)) and λ-cyhalothrin (LC). Firstly, N -(β-aminoethyl)-γ-aminopropytrimethoxysilane (DAMO) was grafted on silica particles surface to synthesis Cu(II)-imprinted polymers to introduce iron imprinted sites. They were then utilized as stabilizers to prepare a stable W/O Pickering HIPEs template (LC as the imprinting molecule), which was then polymerized with dual imprinting sites including Cu(II) and LC. The adsorption equilibrium, kinetic results and selective recognition experiments were exhibited their prospected dual selectivity and simultaneous removal of LC and Cu(II).
✓ 已验证
产品关联
DOI
高影响因子
BIOSENSORS & BIOELECTRONICS
·
2013
·
IF 5.437
Xindong Wang,Lijian Chen,Xiurong Su,Shiyun Ai
A novel sandwich electrochemical immunoassay was developed for ultrasensitive detection of avian leukosis virus subgroup J (ALVs-J) using graphene quantum dots (GQDs) and apoferritin-encapsulated Cu (Cu-apoferritin) nanoparticles for signal amplification . GQDs were used both for the conjugation of primary ALVs-J antibodies (Ab 1 ), and immobilization of secondary ALVs-J antibodies (Ab 2 ) after compounded with Fe 3 O 4 . Cu-apoferritin nanoparticles were first selected to immobilize onto Fe 3 O 4 @GQDs hybrid as electroactive probes. After the well-known sandwich-type assembly, Cu was released from the apoferritin cavity, and then detected by differential pulse voltammetry (DPV). Owing to the huge surface area GQDs provided, a considerable number of antibodies were loaded onto the immunosensor, which effectively increased the electrical signal. And the introduction of Cu-apoferritin nanoparticles increased the loading amount of electroactive probes significantly; hence the signal was once again amplified. To embody the signal amplification property of the protocol, the performance of various labels was compared in detail. The immunosensor displayed excellent analytical performance for the detection of ALVs-J range from 10 2.08 to 10 4.50 TCID 50 /mL with a detection limit of 115 TCID 50 /mL ( S / N =3), and the resulting immunosensor also showed high sensitivity, good reproducibility and stability.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CHINESE JOURNAL OF CATALYSIS
·
2015
·
IF 1.964
Xin Zhao,Lei Huang,Hongrui Li,Hang Hu,Jin Han,Liyi Shi,Dengsong Zhang
Different transition metals were used to modify V 2 O 5 -based catalysts (M-V, M = Cu, Fe, Mn, Co) on TiO 2 via impregnation, for the selective reduction of NO with NH 3 . The introduced metals induced high dispersion in the vanadium species and the formation of vanadates on the TiO 2 support, and increased the amount of surface acid sites and the strength of these acids. The strong acid sites might be responsible for the high N 2 selectivity at higher temperatures. Among these catalysts, Cu-V/TiO 2 showed the highest activity and N 2 selectivity at 225–375 °C. The results of X-ray photoelectron spectroscopy, NH 3 -temperature-programmed desorption, and in-situ diffuse reflectance infrared Fourier transform spectroscopy suggested that the improved performance was probably due to more active surface oxygen species and increased strong surface acid sites. The outstanding activity, stability, and SO 2 /H 2 O durability of Cu-V/TiO 2 make it a candidate to be a NO x removal catalyst for stationary flue gas.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2025
·
IF 9.7
Yanyan Pei,Renyu Liu,Junlan Chen,Yewei Chen,Jinfeng Chen,Zhuwu Jiang
The essential shortcoming of rapid passivation deactivation limits the efficient application of nano zero-valent iron (nZVI) in eliminating disinfection byproducts from drinking water. Copper-coated nano zero-valent iron (Cu-nZVI) bimetallic composites were synthesized to efficiently activate persulfate (PS) to remove nitrosopyrrolidine (NPYR). By introducing Cu-coated coatings, nZVI is protected from direct contact with PS; thus, Cu-nZVI appears to activate PS efficiently and stably without rapid deactivation. Compared with plain nZVI, the constructed Cu-nZVI/PS system significantly increased the removal efficiency for NPYR from 76.3 % to 94.3 % at a pH of 7.0. The Cu-nZVI composites achieved a synergetic effect on the degradation of NPYR by regulating PS activation and reactive oxygen species (ROS) formation, promoting Fe 2+ /Fe 3+ cycling with the Cu-nZVI surface and accelerating the electron transport capacity. The bursting tests and electron paramagnetic resonance (EPR) tests confirmed that multiple types of ROS coexisted in the Cu-nZVI/PS system. Furthermore, vulnerable sites and degradation pathways on the NPYR molecule were predicted by density functional theory (DFT) calculations. Toxicity predictions revealed decreased biotoxicity of NPYR and its intermediates. The NPYR removal efficiency decreased slightly to 81.1 % after 30 days of ageing, which demonstrates the excellent potential of the composites for realistic applications.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
APPLIED CATALYSIS B-ENVIRONMENTAL
·
2024
·
IF 20.2
Haocheng Liu,Luozhen Jiang,Yuanjian Liu,Bingan Lu,Lina Li,Yan Tang,Yanyan Sun,Jiang Zhou
Zinc-air batteries (ZABs) have come to the fore as a prospective energy conversion/storage device because of high energy/power density. The key to promote the development and commercial of ZABs lies in the exploitation of high performance oxygen reduction reaction electrocatalysts. Herein a facile vapor phase migration strategy has been developed to construct bi-metal single-atomic catalysts (SACs) with Fe-N 5 coordination Fe species and Cu-N 3 coordination Cu species atomically dispersed in N/S co-doped carbon matrix (NSC). The type of metal precursors is found to have a significant influence on the form of the metal formed within NSC during pyrolysis, where metal phthalocyanine are more likely to form single-atomic sites whereas metal chlorides are more likely to form nanoclusters. The synergistic effect of single-atomic Cu and Fe sites has been confirmed to accelerate the hydrogenation step of *O intermediates from a viewpoint of experimental and theoretical calculations, which contributes to the improved ORR performance with half-wave potential of 0.89 V. Moreover, the assembled Zn-air battery possesses a high open-circuit potential of 1.47 V, a maximum power density of 152 mW cm −2 , and a specific capacity of 774 mAh g Zn −1 .
✓ 已验证
产品关联
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2024
·
IF 5.1
Yang Yao,Lin Cao,Haoyue Yang,Raz Muhammad,Yingjie Ren,Xinjiang Luo,Fayaz Hussain,Bing Liu,Minmin Mao,Hadi Barzegar Bafrooei,Ehsan Taheri-Nassaj,Kaixin Song
In this study, high-entropy Mg 1.8 R 0.2 Al 4 Si 5 O 18 (R Ni, Ni 1/2 Co 1/2 , Ni 1/3 Co 1/3 Zn 1/3 , Ni 1/4 Co 1/4 Zn 1/4 Cu 1/4 , Ni 1/5 Co 1/5 Zn 1/5 Cu 1/5 Mn 1/5 ) cordierite ceramics based on equimolar ratios were designed and synthesized through the solid-state reaction technique at high temperatures. The effect of various R-ionic substitutions at the octahedral site and their relationship with ionic polarization, chemical bonding, and configurational entropy were explored. These factors have greatly affected the microwave dielectric properties of Mg 1.8 R 0.2 Al 4 Si 5 O 18 ceramics. The presence of cation radius mismatch and electronegativity mismatch at [MgO 6 ]-octahedron lattice sites revealed lattice distortion resulting from multiple cation substitutions. As the entropy values increased, the temperature stability of microwave dielectric properties of Mg 1.8 R 0.2 Al 4 Si 5 O 18 ceramics improved. For R Ni 1/2 Co 1/2 , a higher Q×f of approximately 73,658 GHz @ 13 GHz, with ɛ r ∼4.44 and τ f ∼ −23.9 ppm/°C was obtained. In the case of R Ni 1/5 Co 1/5 Zn 1/5 Cu 1/5 Mn 1/5 , a near zero τ f (−10.7 ppm/°C), ɛ r = 4.68 and Q×f = 35,478 GHz @13 GHz were achieved, making it potentially suitable for practical applications.
✓ 已验证
产品关联
DOI
高影响因子
Molecular Catalysis
·
2024
·
IF 3.9
Kang Zhang,Yuewen Shao,Yuchen Jiang,Lijun Zhang,Shu Zhang,Yi Wang,Song Hu,Jun Xiang,Xun Hu
Metal/biochar catalysts are prepared by direct impregnation of metal salts with biochar produced from pyrolysis. However, the surface structure of the catalyst carrier is affected by the pyrolysis temperature. Different pyrolysis temperatures can produce different pore structures, which can affect the dispersion of active metals. To verify this, Cu/bone biochar catalysts were prepared by directly supporting copper nitrate on the biochar from chicken bone pyrolysis at 400, 500, 650, and 800 °C, respectively. Catalytic performance of Cu/bone biochar catalysts for vanillin hydrogenation was evaluated. The results showed that the hydroxyapatite produced after pyrolysis of chicken bones was relatively stable, which made the catalyst with superior activity and reusability. The catalyst prepared by pyrolysis at a lower temperature had fewer pore structures on its surface, and the active metal Cu was easily sintered. With increasing pyrolysis temperature, organic matter gradually decreased and more pore structures were generated on the surface of the catalyst carrier, which was more conducive to the dispersion of metallic Cu species. The catalyst prepared from the chicken bone pre-pyrolyzed at 800 °C exhibited uniform dispersion of metal Cu, with the average particle size of Cu particles of 11.9 nm, achieving the yield of 91.7 % for 2‑methoxy-4-methyl phenol from hydrogenation of vanillin. In-situ IR characterizations also showed that, with the increase of pyrolysis temperature, the surface functional groups of the catalyst were more conducive to the hydrogenation of vanillin.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2024
·
IF 8.1
Zhengfeng Wang,Xiaoyun Miao,Xingzhi Zhu,Shihang Guo,Donglin Han,Xiaofeng Ye,Zhaoyin Wen
The Ln 2 NiO 4+δ compound (Ln = La, Pr, Nd) finds extensive use as a cobalt-free oxygen electrode material in protonic ceramic electrolysis cells (PCECs) owing to its unique RP-type structure and remarkable catalytic activity . In this study, Cu and Zn co-substitution is employed to fabricate a series of materials, within the La 1 · 2 Sr 0 · 8 Ni 0.5 Cu x Zn 0.5-x O 4+δ system (x = 0.1, 0.2, 0.3, 0.4, denote as LSNCZ14, LSNCZ23, LSNCZ32, and LSNCZ41), and the crystal structure, conductivity, proton absorption and electrochemical properties are comprehensively investigated. The LSNCZ41 exhibits the lowest polarization resistance of 0.83 Ω cm 2 at 600 °C in the symmetric cell. The PCEC single cell incorporating the LSNCZ41 air electrode demonstrates a high electrolysis current density of 1.5 A cm −2 (1.3 V) at 600 °C under 60 % humidity in air, furthermore, negligible degradation is observed under this high current density during electrolysis for over 250 h. These results indicate that LSNCZ41 possesses a higher concentration of interstitial oxygen ions and superior proton absorption capacity , significantly expediting the oxygen reduction reaction (ORR) and ionic transport processes. This material can be considered as a promising candidate for the PCEC air electrodes due to its superior stability in air with high steam content.
✓ 已验证
产品关联
DOI
高影响因子
Molecular Catalysis
·
2025
·
IF 4.9
Faraz Ahmad,Yueli Wen,Muhammad Zeeshan,Bin Wang,Samia Kausar,El Gharrabi Mohamed,Wei Huang
Achieving an optimal acid-base synergy and uniform dispersion of active sites on catalyst surface is essential for high catalytic performance in the side chain alkylation of toluene with methanol (SATM). Herein, we report that ammonium (NH₃) treatment of Cu-modified NaX zeolite catalysts effectively modulates acid-base properties and enhances the dispersion of Cu active sites across the catalyst surface. A series of Cu-modified catalysts were prepared with and without NH₃ treatment and further modified with NaOH to evaluate their synergistic effects. Comprehensive characterization techniques, including Scanning Electron Microscopy (SEM), HAADF-STEM and EDS, Pyridine FTIR, Temperature-Programmed Desorption of NH₃ (TPD-NH₃), X-ray Photoelectron Spectroscopy (XPS O 1 s), and regression analysis, were used to correlate catalyst structure, and acid-base property and nature of acid sites with catalytic performance. Results reveal that NH₃ incorporation into the Cu-modified NaX framework significantly enhances catalytic efficiency by tuning acid-base properties and promoting a homogeneous distribution of Cu active sites. Notably, the 3Cu-4Na-N catalyst achieved a superior yield of ethylbenzene and styrene production, reaching 84.9 %, compared to 64.3 % for the 3Cu-4Na catalyst under identical conditions. Methanol conversion reached 97.7 %, with the catalyst demonstrating robust stability over 168 h of operation. Additionally, 3Cu-4Na-N catalyst exhibited the highest turnover frequency (TOF) reaching 27.3 h -1 , confirming its superior intrinsic activity. This study highlights the critical role of NH₃ in advancing Cu-NaX catalysts for SATM and provides a promising strategy for optimizing catalytic performance through controlled acid-base interactions and active site dispersion.
✓ 已验证
产品关联
DOI
高影响因子
SURFACE & COATINGS TECHNOLOGY
·
2024
·
IF 5.3
Zhaoyang Zheng,Dong Han,Tianyu Zhang,An Du,Ruina Ma,Yongzhe Fan,Xue Zhao,Xiaoming Cao
The Co-depletion zone in WC–Co brazed joints is the main zone of joint failure, so it is crucial to explore novel processes to inhibit the Co-depletion zone and enhance the joint shear strength. In this study, a composite process of pre-plating Cu on the WC–Co surface + brazing was designed. Co-depletion zone reduces from 6 μm to 1 μm due to the Cu plating. Meanwhile, the formation of a plating fusion zone in the filler layer transforms TiCo with a thickness of 2.5 μm into a small number of TiCo particles. Moreover, the high concentration of Cu atoms in the vicinity of the WC particles at the interface changes the Co-segregation layer in the WC into a Cu-rich layer. The concentration of Cu in the filler layer leading to precipitation of TiCu and Ti 2 Cu particles. Ti 2 Cu particles encapsulated by ductile Ag–Cu–In ternary eutectic contribute to inhibit the cracks propagation. The shear strength of the joints was enhanced by 51.3 % to 295 MPa. The composite process of pre-plating on the base material surface + brazing has positive significance in inhibiting the excessive diffusion of elements from the base materials to the filler layer.
✓ 已验证
产品关联
DOI
高影响因子