文献检索

查找使用阿拉丁产品的科研文献

检索与阿拉丁产品相关的同行评审论文、DOI、PubMed 编号、期刊、作者、CAS 号及研究领域。

科研影响力快照

与阿拉丁产品相关的已发表科研成果

在搜索之前,这些指标可帮助访客快速了解产品关联科研的规模与质量。

347,389+ SCI 论文 与阿拉丁产品引用相关
2,303,681.05 总影响因子 匹配文献记录中影响因子的总和
81.20 最高期刊影响因子 匹配期刊中的最高 IF
6.63 平均期刊影响因子 匹配文献的平均 IF

参考指标 指标基于阿拉丁文献引用数据库及期刊影响因子记录。文献关联仅供科研参考,请以原始文献为准。

产品列表

视图 列表 网格

显示第4129至4140个,产品总数6,840个

切换升序
Co2
Green Energy & Environment · 2022 · IF 12.781

Tailor-made microstructures lead to high-performance robust PEO membrane for CO2 capture via green fabrication technique

Wei-Shi Sun,Ming-Jie Yin,Wen-Hai Zhang,Shuo Li,Naixin Wang,Quan-Fu An

Emerging excessive greenhouse gas emissions pose great threats to the ecosystem, which thus requires efficient CO 2 capture to mitigate the disastrous issue. In this report, large molecular size bisphenol A ethoxylate diacrylate (BPA) was employed to crosslink poly (ethylene glycol) methyl ether acrylate (PEGMEA) via the green and rapid UV polymerization strategy. The microstructure of such-prepared membrane could be conveniently tailored by tuning the ratio of the two prepolymers, aiming at obtaining the optimized microstructures with suitable mesh size and PEO sol content, which was approved by a novel low-field nuclear magnetic resonance technique. The optimum membrane overcomes the trade-off challenge: dense microstructures lower the gas permeability while loose microstructures lower high-pressure-resistance capacity, realizing a high CO 2 permeability of 1711 Barrer and 100-h long-term running stability under 15 atm. The proposed membrane fabrication approach, hence, opens a novel gate for developing high-performance robust membranes for CO 2 capture.

CAS / MDL: 67-63-0 32171-39-4
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF APPLIED POLYMER SCIENCE · 2022 ·Vol. 139 ·期 23 ·52287 · IF 3.057

Controllable fabrication of multi-modal porous PLGA scaffolds with different sizes of SPIONs using supercritical CO2 foaming

Jinjing Wang,Yi Zhang,Jianfei Sun,Zhen Jiao

Multi-modal porous scaffolds can promote bone regeneration. In the present study, they were successfully fabricated from poly (lactic-co-glycolic acid) (PLGA)/superparamagnetic iron oxide nanoparticles (SPIONs) by supercritical CO 2 foaming, where SPIONs was employed as heterogeneous nucleation agent. The effects of SPION size on pore nucleation in PLGA/SPIONs nanocomposites were investigated. It was found that the addition of smaller SPIONs size caused the reduction of pore size. Multi-modal porous scaffolds could be available by controlling the SPIONs content, soaking temperature, pressure, and depressurization rate. The porosity of the PLGA/SPIONs scaffolds ranged from (58.68 ± 0.62)% to (94.97 ± 0.14)% could be obtained via adjusting the supercritical CO 2 foaming conditions. Moreover, it was found that the compressive modulus and porosity of the scaffolds were strongly associated with the porous structure. This study provided a new green preparation method for magnetic scaffolds to realize the controllable adjustment of the multi-mode porous scaffolds.

CAS / MDL: 75-09-2
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Molecular Catalysis · 2021 · IF 5.062

Tuning Lewis acid/base on the TiO2-supported Pd-CoOx interfaces to control the CO2 selective hydrogenation

Jing Zhao,Hucheng Zhang,Haiyan Wang,Jianji Wang

A highly attractive aim is to turn CO 2 into useful chemicals selectively and efficiently, but it still retains great challenging to understand the relations between catalytic performances and interface properties. Here, we report an alternative solution to relate the catalytic activity with the strengths of Lewis acids and bases on the Pd-CoO x interfaces. CoO∙TiO 2 /TiO 2 and CoO x /TiO 2 possess the wide spectrum of Lewis acid/base centres, and give the low selectivity and conversion. The introduction of Pd can focus them on the intrinsic centres, and makes Pd-CoO∙TiO 2 /TiO 2 and Pd-CoO x /TiO 2 represent the ideal catalysis. With temperature-programmed desorptions of CO 2 , CO and NH 3 , it is evidenced that the catalytic hydrogenations of CO 2 to CO, CH 4 and CH 3 OH depend on the cooperation of the Lewis acidic/alkaline centres on the interfaces. The studies provide guidelines for rational design and synthesis of heterogeneous catalysts including but not limited to CO 2 hydrogenation.

CAS / MDL: 10026-22-9
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CHEMICAL ENGINEERING JOURNAL · 2021 · IF 13.273

Creating chemisorption sites for enhanced CO2 chemical conversion activity through amine modification of metalloporphyrin-based hypercrosslinked polymers

Huang Ouyang,Kunpeng Song,Jing Du,Zhen Zhan,Bien Tan

The weak physical adsorption of CO 2 in porous organic polymers (POPs) leads to the low utilization of CO 2 in catalysis, calling for the need to develop materials to ensure higher adsorption of CO 2 to achieve high conversion efficiency. In this regard, hydrazine (HZ) was successfully introduced into metalloporphyrin-based hypercrosslinked polymers (HCPs) by post-modification to create abundant CO 2 chemisorption sites in structures for efficient adsorption (Qst value up to 34.7 kJ/mol) and chemical conversion of CO 2 under ambient conditions. The HZ-modified material (HCP-TPP-Co-HZ) exhibits high catalytic performance for different molecular sizes of epoxide substrates with excellent yields (reaching 98 % of propylene oxide), much superior than that of HCP-TPP-Co-SO 3 H (64 %), which can be ascribed to the abundant chemisorption sites for CO 2 reactants. Moreover, HCP-TPP-Co-HZ has good stability and shows excellent recycling performance (more than 5 times) for the coupling of CO 2 with substituted epoxides at room temperature and atmospheric pressure. This strategy to introduce amine groups as CO 2 chemisorption sites has been demonstrated to be a new pathway for the design of efficient HCPs catalysts for chemical conversion of CO 2 .

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
SEPARATION AND PURIFICATION TECHNOLOGY · 2023 · IF 8.6

Accelerated interfacial charges migration on Z-scheme CoAl-LDH/RGO/InVO4 heterojunction for photocatalytic reduction of CO2

Jingwen Wei,Ting Liang,Shiming Zhang,Jinhang Yang,Zhihong Li,Zuji Li,Songyu Fan,Zebin Yu,Yanping Hou

In this work, the Z-scheme layered double hydroxide (LDH)/reduced graphene oxide (RGO)/indium vanadate (InVO 4 ) heterojunction was synthesized by a simple hydrothermal synthesis. RGO , with excellent electron mobility, endowed rapid charge migration and separation between the CoAl-LDH and InVO 4 . Various characterizations and tests showed that the LDH/RGO/InVO 4 heterojunction exhibited superior optical properties, and its carriers’ transfer pathway conformed to Z-scheme mechanism. Under visible light illumination, CO was observed to be the main product during photocatalytic CO 2 reduction, and the LDH/RGO/InVO 4 -15 exhibited the highest CO yield of 204.86 μmol g −1 within 2 h, approximately 2.62 times of pristine CoAl-LDH (78.2 μmol g −1 ). In addition, LDH/RGO/InVO 4 -15 showed favorable structure stability and performance stability. In situ fourier infrared spectroscopy (ISFT-IR) analysis demonstrated that the predominant intermediates of CO 2 reduction process were carboxylate (COOH*) and bicarbonate (HCO 3 *). Accordingly, possible pathways of CO 2 reduction to CO were deduced. This work can advance the development of efficient Z-scheme heterojunction photocatalysts for CO 2 reduction.

CAS / MDL: 107-21-1 57-13-6
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Greenhouse Gases-Science and Technology · 2023 ·Vol. 13 ·期 5 ·689-698 · IF 2.2

The efficient CO2 fixation catalyzed by K-doped g-C3N4 catalyst for synthesizing benzimidazoles at atmospheric pressure

Xuewei Tu,Luping Zhang,Yutong Chen,Shouxin Zhu,Can Sun,Jiali Jin,Min Liu,Hui Zheng

The conversion of CO 2 into valuable chemicals to reduce greenhouse gas emissions has received extensive attention. Converting CO 2 into pharmaceutical intermediates via graphitic carbon nitride (CN) at atmospheric pressure is a challenge. In this work, a series of novel graphitic carbon nitrides (K-CN) catalysts with different doping ratios of K were synthesized by post-treatment of CN with KOH as a dopant under magnetic stirring. Herein, substrates of o -phenylenediamine with different electron-donating/withdrawing groups were employed to convert CO 2 into high-value heterocyclic benzimidazoles. The optimal reaction conditions were determined by a single factor optimization approach. A series of benzimidazole derivatives were synthesized with a yield of up to 96% under atmospheric pressure, indicating that the catalyst can efficiently fix CO 2 . This work not only designs a simple and low-cost K-CN catalyst but also provides a new pathway for converting CO 2 into valuable benzimidazole derivatives at atmospheric pressure. © 2023 Society of Chemical Industry and John Wiley & Sons, Ltd.

CAS / MDL: 1575-37-7 95-54-5
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
SCIENCE OF THE TOTAL ENVIRONMENT · 2023 · IF 9.8

CO2 sequestration and CaCO3 recovery with steel slag by a novel two-step leaching and carbonation method

Can Cheng,Wenjun Huang,Haomiao Xu,Zhisong Liu,Xianwei Li,Hongzhi Shi,Yongmei Yu,Zan Qu,Naiqiang Yan

The steel smelting process produces extensive CO 2 and Ca-containing steel slag (SS). Meanwhile, the low value utilization of steel slag results in the loss of Ca resources. CO 2 sequestration utilizing SS can reduce carbon emissions while achieving Ca circulation. However, conventional SS carbon sequestration methods suffer from slow reaction rates, finite Ca usage efficiency, and difficulty separating the CaCO 3 product from SS. Herein, an innovative two-step leaching (TSL) and carbonation method was presented based on the variations in leaching efficiency of activated Ca under different conditions, aiming at efficient leaching, carbon sequestration, and high-value reuse of SS. This method employed two NH 4 Cl solutions in sequence for two leaching operations on SS, allowing the Ca leaching rate to be effectively increased. According to the findings, TSL could increase the activated Ca leaching rate by 26.9 % and achieve 223.15 kg CO 2 /t SS sequestration compared to the conventional one-step leaching (CSL) method. If part of the CaCO 3 is recovered as a slagging agent, about 34.1 % of the exogenous Ca introduction could be saved. In addition, the CO 2 sequestration of TSL did not significantly decrease after 8 cycles. This work proposes a strategy that has the potential for recycling SS and reducing carbon emissions.

✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
SEPARATION AND PURIFICATION TECHNOLOGY · 2023 · IF 8.6

Fabricating self-templated and N-doped hierarchical porous carbon spheres via microfluidic strategy for enhanced CO2 capture

Lingling Xie,Ziheng Jin,Zhongde Dai,Tongxiao Zhou,Xianggang Zhang,Yulong Chang,Xia Jiang

N-doped porous biochar is a promising material for CO 2 capture due to its easy regeneration and high CO 2 selectivity. In this study, a new strategy was proposed to design monodisperse porous carbon spheres by microfluidics system with chitosan in-situ grow ZIF-8, utilizing ZIF-8 as a self-sacrificing template and nitrogen dopant. The mesoporous volume and N content of carbon spheres can be adjusted through the ZIF-8 content in the microfluidic system and carbonization temperature, within 0.01 ∼ 0.48 cm 3 /g and 3.23 ∼ 19.25%, respectively. The optimum sample (CZ 2 -900) exhibited superior CO 2 /N 2 selectivity at 40. Adsorption kinetics and diffusion resistance indicated that CO 2 adsorption in CZ 2 -900 is controlled by the process of CO 2 diffusion from the surface of the basic site to mesopores. This was the first attempt at using a microfluid chip to grow ZIF-8 in chitosan skeleton and pyrolysis approach to synthesize N-doped porous carbon sphere where both additional template agent and activator are non-used, revealing the potential of microfluidic technology for the precise synthesis of highly selective CO 2 capture materials.

CAS / MDL: 9012-76-4 693-98-1
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CHEMICAL ENGINEERING JOURNAL · 2023 · IF 15.1

Doping Sn4+ ionized cocatalyst in CdSe/S colloidal crystal for promoting photocatalytic CO2 reduction under visible light

Yingkui Yan,Ye Wang,Zhenxin Zhang,Songtao Zhang,Jinhua Ye,Li Shi

The exploration of low-cost and efficient cocatalysts is vitally important for attaining reliable and affordable photocatalytic CO 2 conversion. Here, it is found that post-transition metal ions (Sn 4+ ) doped CdSe/S colloidal crystal can serve as effective photocatalyst for CO 2 reduction under visible light, in which Sn 4+ serves as an ionized cocatalyst. Specifically, Sn 4+ doped CdSe/S colloidal crystal shows an improved and stable photocatalytic CO 2 reduction performance with CO generation rate of 50.3 μmol h −1 and H 2 generation rate of 7.8 μmol h −1 in the presence of triethanolamine as sacrificial agent. The improved photocatalytic activity can be ascribed to the increased light harvesting ability, enhanced CO 2 adsorption capability and the improved surface charge transfer efficiency induced by Sn 4+ dopant.

CAS / MDL: 7790-78-5 102-71-6
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CHEMICAL ENGINEERING JOURNAL · 2023 · IF 15.1

Facile fabrication of silica aerogel supported amine adsorbent pellets for Low-concentration CO2 removal from confined spaces

Pu Huang,Xinzheng Wei,Xinmei Wang,Zhengjun Gu,Yafei Guo,Chuanwen Zhao

Amine-based adsorbents show promise for removing low-concentration CO 2 from environmental control and life support systems (ECLSSs), while the powder adsorbents are facing the challenges of reaction non-uniformity, pressure drop and material elutriation. To solve the problems, amine-based adsorbent pellets are fabricated by the extrusion–spheronization (ES), agar-assisted moulding (AM) and graphite-casting (GC) methods. The adsorbent pellets are further modified with pore-forming template for improved CO 2 adsorption performance. The influences of granulation and pore-forming template modification on the structure-performance relationships of the adsorbent pellets are investigated. Granulation exerts adverse effect on the pore structure of tetraethylenepentamine supported on silica gel (TEPA-SG) adsorbent, which is not conducive to the bulk diffusion of CO 2 , and the CO 2 adsorption capacity and kinetics thus have been impaired. The TEPA-SG-ES adsorbent pellets prepared by the extrusion–spheronization method show a relatively higher CO 2 capture capacity of 1.01 mmol CO 2 /g due to better textural parameters and uniform dispersion of amine species. Thanks to the extrusion process, the adsorbent pellets also exhibit good mechanical properties with a high compressive strength of 10.90 MPa and low abrasion index of 0.36%. Both the textural properties and CO 2 uptakes of the pellets can be restored upon template modification, and the promoting effect depends on the different templates employed due to their distinct pyrolysis rates and pathways. Mechanical properties will be adversely affected by the doped pore-forming template. The TEPA-SG-ES-UA pellets prepared with urea modification exhibit a great CO 2 capture capacity of 1.48 mmol CO 2 /g and good mechanical properties with a high compressive strength of 4.90 MPa and a low abrasion index of 0.87%, and it could be a nice adsorbent candidate for removing low-concentration CO 2 from ECLSSs.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
ACS Applied Materials & Interfaces · 2023 · IF 9.5

CO2-Activation Nanofiber Carbon Paper as a High-Performance Interlayer for Trapping Polysulfides in Li–S Batteries

Ling Meng,Chenying Song,Qixuan Lin,Guanghang Sun,Jin Long,Xiting Zhang,Hailong Li,Jian Hu,Siyu Ye

Lithium–sulfur (Li–S) batteries have high theoretical energy density but low sulfur utilization due to the inherent insulating nature of sulfur and the shuttle effect of polysulfides. Herein, the CO2-activation carbon paper was prepared by poly(p-phenylenebenzobisoxazole) (PBO) nanofiber and was first applied as an interlayer for efficiently alleviating the shuttle effect of polysulfides in Li–S batteries. This interlayer exhibits good flexibility and strength with rich −C═O and −COOH functional groups on the three-dimensional porous structure, which improves chemical adsorption on Li2Sx species and ion rapid diffusion via interconnected diffusion channels and thus enhances the electrochemical kinetics. The initial specific capacity is 1367.4 mAh g–1 and remains 999.8 mAh g–1 after 200 cycles at 0.2C and 780.1 mAh g–1 at 5C, and the Coulombic efficiency is high, up to 99.8%, which is much better than that for the carbon paper without CO2 activation. The highly conductive flexible PBO carbon paper may bring breakthroughs in performance and thus lead to more practical applications of Li–S batteries.

CAS / MDL: 68-12-2 7704-34-9
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
ACS Applied Polymer Materials · 2023 · IF 5

Amine-Impregnated Porous Organic Polymers with Chemisorption Sites for Highly Efficient CO2 Chemical Conversion under Ambient Conditions

Huang Ouyang,Kunpeng Song,Irshad Hussain,Bien Tan

CO2 cycloaddition with epoxides is an important chemical process for CO2 conversion to generate cyclic carbonates, which are major sources and intermediates of fine chemicals and electrolytes. Unfortunately, the catalytic efficiency of various porous organic polymers (POPs) for the CO2 cycloaddition process remains poor and necessitates severe conditions or a prolonged reaction time at mild temperature and pressure. Only a few reports have emphasized the improvement of the interaction among POP heterogeneous catalysts with CO2, in addition to many attempts to boost efficiency by increasing the adsorption capacity of POPs for CO2. Furthermore, chemisorption, which can efficiently adsorb and activate CO2, could be used to establish a high binding affinity and interaction among POPs and CO2. Herein, we report amine-impregnated porous organic polymers, i.e., hyper-cross-linked polymer (HCP)-tetraphenylporphyrin (TPP), using a wet impregnation method that differentiates itself from the chemical grafting method due to the simplicity of sample preparation and high amine loading to create abundant CO2 chemisorption sites to effectively adsorb and activate CO2 for easier cycloaddition reactions under mild conditions. The amine-functionalized heterogeneous catalysts HCP-TPP-Co-EDA-10 and HCP-TPP-Co-PEI-5 showed a strong binding affinity with CO2 (Qst value of 31.8 and 52.5 kJ mol–1) and high catalytic yield (reaching up to 99%) under mild temperature and pressure. Interestingly, the turnover number (TON) and turnover frequency (TOF) could reach up to 6930 and 193 h–1, respectively, which are one of the highest values reported so far under mild conditions. Furthermore, HCP-TPP-Co-EDA-10 and HCP-TPP-Co-PEI-5 have excellent recyclability and stability (more than five recycling times) for CO2 conversion. Additionally, a possible mechanism is also proposed for the catalytic conversion reaction. This simple strategy of utilizing amines as chemisorption sites for CO2 is demonstrated as an approach to designing highly efficient functionalized hyper-cross-linked polymers (HCPs) for CO2 capture and chemical conversion.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
已复制

文献关联基于可获得的产品、CAS、DOI 及引用记录。收录不代表作者或出版方对阿拉丁产品的背书,请以原始文献为准。