JOURNAL OF MOLECULAR STRUCTURE
·
2024
·
IF 4
Shaopeng Zhang,Jie Ding,Dayong Tian,Jing Wang,Jiale Zhang,Minghua Lu
China faces severe antimony pollution due to long-term, high-intensity mining and smelting operations. Long-term exposure to Sb(III) can lead to chronic respiratory problems. Adsorption method is used to remove Sb(III) because of its simplicity, economy and high efficiency. Therefore, a novel MIL-101(Fe)-Cl/SA hydrogel with oxidation-sorption bifunctionality was developed. 1602 cm −1 and 1025 cm −1 correspond to N H and S = O indicate N-chlorosulfonamide is bonded to MIL-101(Fe)-Cl/SA. MIL-101(Fe)-Cl/SA exhibited rough and wrinkled surfaces with numerous irregular particles by SEM. The presence of O (22 %) and Cl (2 %) confirmed the incorporation of N-chlorosulfonamide and SA into MIL-101(Fe)-Cl/SA by EDS and mappings. The adsorption capacities of MIL-101(Fe)-Cl/SA were 86 mg/g at 298 K and 123.21 mg/g at 328 K by Langmuir model. Kinetic and equilibrium correspond to pseudo-second-order and Langmuir model, respectively. Adsorption was spontaneous and endothermic by thermodynamic analysis. MIL-101(Fe)-Cl/SA exhibited enhanced selectivity in solution containing various ions. Moreover, MIL-101(Fe)-Cl/SA demonstrated potential for regeneration and reuse. The removal process primarily involved oxidation, electrostatic interaction, and complexation. In summary, the capability of MIL-101(Fe)-Cl/SA to adsorb and oxidize Sb(III) underscores its promising potential in mitigating the hazards associated with Sb(III).
✓ 已验证
产品关联
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2024
·
IF 6.3
Menglu Wang,Bolong Liang,Shumin Lin,Zhe Zhao,Hongbin He,Xiliang Li,Shu-xuan Liang
The magnetic Fe 3 O 4 @ZIF-8 with high adsorption properties and easy separation were embedded in BiOX (X = Cl, Br, I) to synthesize Fe 3 O 4 @ZIF-8@BiOX using a simple one-pot solvothermal strategy. The crystal structure, surface morphology, photoelectric properties, thermal stability and magnetic response of the three materials were compared and analyzed, and the effect on the removal of OTC and Cr(VI) from single and coexisting systems by adsorption-photocatalysis is discussed. The results show Fe 3 O 4 @ZIF-8@BiOI has the highest separation efficiency of photogenerated carriers upon photoexcitation and stronger light absorption capacity, and exhibits better adsorption-photocatalytic activity than the other two materials in the photocatalytic reduction of Cr(VI) (68 % and 65 % removal for single and coexisting systems) and degradation of OTC (86 % and 59 % removal for single and coexisting systems). It is noteworthy that in the coexistence of Cr(VI) and OTC, a slight decrease of removal occurred, which could be due to a competitive effect between two pollutants being greater than the synergistic effect. ∙O 2 - is the main active substances in the adsorption-photocatalysis process. Finally, this work demonstrates the excellent adsorption and photocatalytic ability of Fe 3 O 4 @ZIF-8@BiOI for the simultaneous removal of Cr(VI) and OTC, which has great potential for practical wastewater treatment.
研究领域:
环境科学
·
材料科学
✓ 已验证
DOI
高影响因子
EUROPEAN POLYMER JOURNAL
·
2018
·
IF 3.741
Teng Xue,Erjun Tang,Xiaofeng Guo,Ruihong Wang,Lei Zhao,Jian Zhou,Shaojie Liu
The ionic liquid 1-(triethylene-tetramine)ethyl-3-methyl chloride ([N 4 MIM]Cl) was first prepared to replace the organic ligand coordinating with CuBr to catalyze atom-transfer radical polymerization (ATRP) in ionic liquid system. [N 4 MIM]Cl was synthesized via the intermediate IL 1-chloroethyl-3-methyl chloride ([CeMIM]Cl) reacting with the aliphatic amine triethylene tetramine (TETA) and [CeMIM]Cl) was obtained by N′-alkylation of N -methylimidazole with 1,2-dichloroethane. This catalyst has been applied to the ATRP of methyl methacrylate (MMA) in the ionic liquid (IL) 1-allyl-3-methylimidazolium chloride ([AMIM]Cl) and presented a perfect catalytic performance. The chemical structures of the ILs obtained were confirmed by FTIR and 1 H NMR. The coordination ability of [N 4 MIM]Cl was assessed by cyclic voltammetry (CV) and its coordination mechanism towards CuBr was discussed. The [N 4 MIM]Cl/CuBr catalyst system showed good controllability in the aforementioned ATRP reaction in [AMIM]Cl. The amount of residual Cu 2+ in the polymer product was determined by atomic absorption spectrometry (AAS) and the result showed that the Cu catalyst was easily separated from the obtained polymer. Thus, the coordinating IL could overcome the shortcomings of traditional organic ligands, such as poor compatibility with IL media resulting in the weakly catalytic performance and inferior separation of the catalyst from the polymer. It implied that the coordinating ionic liquid ([N 4 MIM]Cl) has highly promising application in the ATRP of ionic liquid system.
研究领域:
材料化学
·
高分子化学
✓ 已验证
DOI
高影响因子
JOURNAL OF CHEMICAL RESEARCH
·
2020
·
IF 0.593
Zhenzhen Geng,Hong-yu Zhang,Guohui Yin,Yuecheng Zhang,Jiquan Zhao
The ionic liquid 1-methyl-3-(3-sulfopropyl)imidazolium chloride ([MIMPs]+Cl-) in combination with 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO) and sodium nitrite (NaNO2) as a catalytic system demonstrates high efficiency in the one-pot two-step aerobic oxidative condensation of benzyl alcohols with 1,2-phenylenediamines to give benzimidazoles. Various benzimidazoles are obtained in good to excellent yields by this strategy.
研究领域:
有机化学
·
催化化学
✓ 已验证
DOI
高影响因子
ANALYTICA CHIMICA ACTA
·
2021
·
IF 6.558
Linjie Wang,Xuechao Xu,Peng Liu,Mengzhu Wang,Xiangheng Niu,Jianming Pan
Abnormal levels of halide ions in drinking water have enormous threats to human health, and thus designing reliable and sensitive methods to quantify and distinguish these ions becomes extremely crucial. Herein, we develop a single-nanozyme colorimetric array based on target-induced differential surface passivation for the quantification and discrimination of Cl − , Br − and I − ions. Silver citrate (Ag 3 Cit) is designed as an oxidase mimic to efficiently catalyze the 3,3′,5,5′-tetramethylbenzidine (TMB) chromogenic reaction. When halide ions (Cl − , Br − and I − ) are present, due to their different precipitation interactions with the Ag(Ⅰ) entity in Ag 3 Cit, they can passivate the active surface of the nanozyme to various degrees, resulting in the inhibited TMB chromogenic reaction differentially. According to this principle, simple and efficient quantitative detection of Cl − , Br − and I − ions was achieved, with all the detection limits down to the nM level. By employing Ag 3 Cit as a single sensing element, a nanozyme catalysis-based colorimetric array was further established, and both individual and mixed ions were successfully distinguished by integrating the array with principal component analysis . Accurate identification of unknown samples was also verified via a double-blind protocol, indicating potential applications of the array in practice.
研究领域:
分析化学
·
环境科学
·
生物医学工程
✓ 已验证
DOI
PubMed
高影响因子
Journal of Energy Storage
·
2026
·
IF 10.7
Dong Deng,Yuhan Li,Gang Liu,Xinmei Liu,Qianshi Wang,Hongfei Chen,Dongbo Wang,Mingyang Wu,Minghan Li,Fei Li,Yuewu Huang,Liancheng Zhao
BiOCl and its derivatives show considerable promise for supercapacitor applications because of their high theoretical specific capacity and rich redox activity. However, their practical performance is often limited by poor electrical conductivity and structural instability. To address these issues, we constructed a BiOCl/Bi₂₄O₃₁Cl₁₀ heterojunction to improve both charge transport and structural stability. A flake-like BiOCl precursor was first synthesized and then electrochemically treated at a constant current of 0.02 A over a wide pH range (1−13) to generate a BiOCl/Bi₂₄O₃₁Cl₁₀ heterojunction, denoted as BiOCl-1/24-X. By tuning the pH of the reaction system, pH-dependent formation of a reconstructed Bi₂₄O₃₁Cl₁₀ phase on the BiOCl surface was achieved, thereby strengthening the interfacial interaction between the two phases. This interfacial reconstruction process modulated the extent of heterointerface formation and the concentration of oxygen-vacancy-related defects, thereby promoting ion transport and charge-transfer kinetics. The results indicate that the sample treated at pH = 9 exhibits battery-type energy-storage behavior dominated by diffusion-controlled processes. Accordingly, it delivered a specific capacity of 411C·g −1 at 1·A g −1 , far exceeding that of pristine BiOCl (80C·g −1 ). Moreover, it retained 79.3% of its initial capacity after 10,000 cycles. It also achieved an energy density of 35.67 Wh·kg −1 at a power density of 923.83 W·kg −1 . In a practical demonstration, the BiOCl-1/24//AC device powered a 3.2 V LED for 900 s, highlighting its application potential. This work proposes a facile electrochemical interfacial reconstruction strategy for developing high-performance electrode materials, offering a simpler and more effective alternative to conventional chemical methods.
✓ 已验证
DOI
高影响因子
Molecular Catalysis
·
2025
·
IF 4.9
Esimoneze Emmanuel Chinedu,Dilong Qiang,Xueqian Wu,Wei Liu,Haizhou Cao,Zhaolian Ye,Zhen Li,Songjian Zhao
The Pt-based catalyst for purifying chlorinated volatile organic compounds (Cl-VOCs) has the advantages of high catalytic efficiency and low ignition temperature, but the problem of poor resistance to chlorine and water poisoning has not been effectively solved. A series of 0.5 Pt-Ti catalysts were prepared for chlorobenzene (CB) catalytic oxidation by adjusting the interfacial stability and dispersibility of the TiO 2 and Pt through the organic acid strategy in this study. The introduction of tartaric acid (TA) effectively enhanced the surface reduction performance of 0.5Pt-Ti-TA and the proportion of Pt 4+ on the surface. In addition, TA can strongly coordinate with Ti center to form stable titanium-containing complexes, improve the dispersion of Pt, prevent particles from agglomerating, and make the distribution of active sites more uniform. The designed 0.5Pt-Ti-TA exhibits excellent chlorine and water resistance at 300℃ (5 %H 2 O, 500 ppm CB), and has a higher potential of application.
研究领域:
环境科学
·
催化化学
✓ 已验证
产品关联
DOI
高影响因子
Journal of Environmental Chemical Engineering
·
2025
·Vol. 14
·期 1
·120487
·
IF 7.2
Jifang Zhang,Chengcheng Suo,Hongru Zhang,Wei Li,Sha Luo,Bing Tian,Chunhui Ma,Shouxin Liu
Constructing an efficient and low-cost electrocatalyst was highly necessary in electrocatalytic lignin depolymerization study. We prepared a unique 1D/2D/1D nanoflower electrocatalyst (Ti 20 @ZIS-Sv@C 0.5 (Ⅱ)) composed of TiO 2 , ZnIn 2 S 4 and C nanosheets by electrostatic self-assembly through solvothermal method. The TiO 2 was located as the core of catalyst and covered by the C deposited ZnIn 2 S 4 nanosheets. The electrochemical impedance (R ct , 248.5 Ω; R L , 6.511 Ω), C dl (1.75817 mF cm −2 ), Tafel efficiency (6.28 mV dec −1 ) and photocurrent intensity (5.23 μA) of Ti 20 @ZIS-Sv@C 0.5 (Ⅱ) exhibited higher electrocatalytic activity than that of original ZnIn 2 S 4 . Under optimized conditions, electrocatalytic process achieved 100 % C α -C β (β-O-4) and C Ar -O (α-O-4) cleavage efficiency and 244.37 mg g −1 benzaldehyde yield. We have further indicated C α -C β (β-O-4) and C Ar -O (α-O-4) cleavage mechanism by Cl-induced radical oxidation pathway. The electrocatalytic depolymerization of G-type lignin could obtained at least 14 molecular products (including 18.21 mg g −1 2-hydroxy-1-phenylethan-one, 11.39 mg g −1 pyrocatechol and 1.25 mg g −1 benzaldehyde). Mechanism investigation suggested the generation of chlorine radical (•Cl), followed by C-H activation and synergistic effect of Ti 20 @ZIS-Sv@C 0.5 (Ⅱ), leading to highly efficient lignin linkages cleavage. This work has developed an efficient electrocatalyst for lignin valorisation to produce aromatics via an electrocatalytic radical pathway.
研究领域:
电催化
·
可再生能源
·
材料科学
·
绿色化学
·
生物质高值化
✓ 已验证
DOI
高影响因子
ACS Applied Energy Materials
·
2024
·
IF 5.4
Lei Zhou,Xin Wei,Junxiang Zhang,Xuecui Mei,Yun Li,Chaoyue Zheng,Furong Zhang,An Wen,Bin Wang
Sulfide solid electrolytes (SSEs) have some huge advantages in high room-temperature conductivity, good thermal stability, low interfacial resistance, etc. They are one of the ideal solid electrolytes for developing high energy density and high safety for all-solid-state lithium batteries (ASSLBs). However, the preparation of SSEs requires expensive Li2S as the raw material, whose high cost limits its practical application. Herein, a cost-effective SSE Li7.3P2.9S10.75X0.3 (X = F, Cl, Br, and I) was designed and prepared by using low-cost lithium and sulfur instead of expensive Li2S. Significantly, the cost of SSEs was reduced from $169.72 to $28.13 kg–1 based on replacing the Li2S strategy. Moreover, the prepared Li7.3P2.9S10.75X0.3 (X = F, Cl, Br, and I) solid electrolytes have a high ionic conductivity of 1.86–2.73 mS cm–1 at room temperature and a high voltage window of 5 V. On this basis, we assembled the all-solid-state lithium battery TiS2/Li7.3P2.9S10.75I0.3/Li–In, which presented a high initial discharge capacity of 219 mA h g–1 at room temperature and satisfactory cycle stability with a capacity retention of 86.7% after 100 cycles at 0.50 mA cm–2. This work provides an effective strategy for reducing the cost of SSEs, advancing the practical process of ASSLBs.
研究领域:
材料科学
·
能源技术
✓ 已验证
DOI
高影响因子
Journal of Materials Chemistry C
·
2026
·
IF 5.1
Hai Ou,Xin An,Peng Li,Weikang Dong,Keke Guan,Jiaxin Qin,Yuanting Wu
CsPbX 3 (X = I, Br, Cl) perovskite quantum dots (QDs) have shown great potential in optoelectronic devices due to their wide tunable bandgap, high photoluminescence quantum yield, and narrow emission spectra. Currently, methods for regulating blue light emission through component engineering or dimensional engineering suffer from issues such as halogen phase separation and increased defects, making it difficult to meet the strict requirements of display technology for pure blue light (CIE y < 0.15). Additionally, traditional synthesis processes are complex and have poor compatibility with Micro-LED miniaturization technology, which restricts their industrial application. Therefore, this study proposes an efficient and green spray drying method. By dissolving the perovskite precursors and halide salts in an aqueous solution, CsPb(Cl/Br) 3 QDs can be rapidly (<10 s) synthesized without organic solvents, and continuous tuning from green to blue light is achieved. This method effectively suppresses surface defects and phase separation through Cl element encapsulation, significantly enhancing stability.Moreover, its excellent processability supports spraying and film formation on any substrate, enabling the direct preparation of highly uniform Mini/Micro-LED pixel units. This technology provides a new approach for large-scale, low-cost manufacturing of perovskite QDs and is expected to accelerate the commercialization process of next-generation display technologies.
✓ 已验证
产品关联
DOI
高影响因子
LANGMUIR
·
2023
·
IF 3.9
Hongqi Nie,Zikangping Wang,Xue-Xue Zhang,Su-Lan Yang,Zhi Ren,Qi-Long Yan
In this study, a 2D structured triaminoguanidine-glyoxal polymer with a high nitrogen content has been coordinated with metal ions to produce energetic metal complexes (TAGP-Ms) employed as energetic burn rate inhibitors. The metal ions (Ba2+, K+, and Ca2+) are elaborately selected based on their ability of suppressing the burn rate of composite propellants. The CL-20 crystals were intercalated with prepared TAGP-Ms materials via a solvent–antisolvent method for realization of the precise control on burning behaviors of studied propellants. The influence of TAGP-Ms inhibitors on thermal decomposition and combustion characteristics of high-energy composite propellants was evaluated using thermal analysis and a combustion diagnostic method. Results of TGA/DSC-FTIR measurements suggest that the thermal decomposition of CL-20-containing composite propellants was found to be constrained by varied degrees as a result of TAGP-Ms additions, in which the TAGP-K displays a stronger effect on suppressing the thermal decomposition of CL-20 compared with that of other TAGP-Ms. The FTIR spectra indicate that the primary gaseous phase products are composed of N2O, H2O, and CO2 in CL-20 decomposition, as well as by HCl, H2O, NO2, and N2O in the decomposition of AP for all studied composite propellants. The combustion characterizations show that the TAGP-K-containing composite propellant exhibits a significantly reduced rate of heat release but is associated with a higher flame radiation intensity increased by 4.2% compared with that of the reference propellant, which clearly implies that the TAGP-K is capable of suppressing the energy release rate while ensuring the high energetic features of propellants to be well maintained. Moreover, the burn rate pressure exponents are considerably decreased by ∼10% for the TAGP-K-containing propellants in comparison with those of propellants with the typical formulation, which strongly suggests that TGAP-Ms are promising candidates for tuning the combustion behaviors of composite propellants by influencing the decomposition processes of CL-20 and AP collectively.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
MOLECULES
·
2023
·Vol. 28
·期 14
·5355
·
IF 4.6
Keyan Chen,Shiqi Fu,Chenyu Jin,Fan Guo,Yu He,Qi Ren,Xuesheng Wang
Smartphone-assisted fluorescence and colorimetric methods for the on-site detection of Hg2+and Cl−were established based on the oxidase-like activity of the Au–Hg alloy on the surface of Au/Cu/Ti3C2NSs. The Au nanoparticles (NPs) were constructed via in-situ growth on the surface of Cu/Ti3C2NSs and characterized by different characterization techniques. After the addition of Hg2+, the formation of Hg–Au alloys could promote the oxidization of o-phenylenediamine (OPD) to generate a new fluorescence emission peak of 2,3-diaminopenazine (ADP) at 570 nm. Therefore, a turn-on fluorescence method for the detection of Hg2+was established. As the addition of Cl−can influence the fluorescence of ADP, the fluorescence intensity was constantly quenched to achieve the continuous quantitative detection of Cl−. Therefore, a turn-off fluorescence method for the detection of Cl−was established. This method had good linear ranges for the detection of Hg2+and Cl−in 8.0–200.0 nM and 5.0–350.0 µM, with a detection limit of 0.8 nM and 27 nM, respectively. Depending on the color change with the detection of Hg2+and Cl−, a convenient on-site colorimetric method for an analysis of Hg2+and Cl−was achieved by using digital images combined with smartphones (color recognizers). The digital picture sensor could analyze RGB values in concentrations of Hg2+or Cl−via a smartphone app. In summary, the proposed Au/Cu/Ti3C2NSs-based method provided a novel and more comprehensive application for environmental monitoring.Keywords:Au/Cu/Ti3C2NS;Au–Hg alloy;oxidase-like activity;smartphone;colorimetric detection
✓ 已验证
产品关联
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）