ACS Applied Materials & Interfaces
·
2022
·
IF 10.383
Tiansheng Gan,Qi Xiao,Stephan Handschuh-Wang,Xiaoqin Huang,Haifei Wang,Xiaobo Deng,Shuangyan Hu,Ben Wang,Qixing Wu,Xuechang Zhou
Adhesion and spreading of liquid metals (LMs) on substrates are essential steps for the generation of flexible electronics and thermal management devices. However, the controlled deposition is limited by the high surface tension and peculiar wetting and adhesion behavior of LMs. Herein, we introduce gelatin-regulated LM droplet deposition and sintering (GLMDDS), for the upscalable production of conformally adhesive, solidlike, yet transient LM thin films and patterns on diverse substrates. This method involves four steps: homogeneous deposition of LM microdroplets, gelation of the LM-gelatin solution, toughening of the gelatin hydrogel by solvent displacement, and peeling-induced sintering of LM microdroplets. The LM thin film exhibits a three-layer structure, comprising an LM microdroplet-embedded tough organohydrogel adhesion layer, a continuous LM layer, and an oxide skin. The composite exhibits high stretchability and mechanical robustness, conformal adhesion to various substrates, high conductivity (4.35 × 105 S·m–1), and transience (86% LM recycled). Large-scale deposition (i.e., 5.6 dm2) and the potential for patterns on diverse substrates demonstrate its upscalability and broad suitability. Finally, the LM thin films and patterns are applied for flexible and wearable devices, i.e., pressure sensors, heaters, human motion tracking devices, and thermal management devices, illustrating the broad applicability of this strategy.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
NEW JOURNAL OF CHEMISTRY
·
2022
·Vol. 46
·期 39
·18744-18750
·
IF 3.925
Dawang Chu,Hui Zhou,Zhicheng Luo
Selective conversion of glycerol to lactic acid requires the synergistic activation of C–H, C–O, and O–H. Herein, we report an inexpensive Fe–Cr/TiO2 catalyst that achieves lactic acid formation with a high selectivity of 60.5%. By changing the Fe/Cr ratios and reduction temperatures, the structures of Vő and Vő-OH were altered, which determined the overall oxidation–dehydration–isomerization process. The in situ ATR-IR experiments confirmed the activation of glycerol by adsorbing the primary −OH, and a series of control experiments verified that Fe was responsible for the cleavage of C–H and O–H, while CrOx catalyzed the activation of C–O and C–H. This work designs a hydrothermal catalyst with multifunctional ability, which may guide the rational catalyst design for the selective oxidation of glycerol to lactic acid.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Energy Storage
·
2022
·
IF 8.907
Sensen Yu,Jie Xu,Cuili Xiang,Yongjin Zou,Zhicong Hu,Fen Xu,Lixian Sun
Transition metal sulfide porous multishell nanostructures with high active sites have great potential for application as bifunctional materials. Herein, bifunctional metal-organic framework (MOF)-derived nitrogen-doped porous multishell CuCoS@NiCoS (N–CCS@NCS) nanospheres are synthesized on Cu–Co–O substrates. The tightly connected nanocluster particles transformed by MOFs have more active sites and surface area. The ion transport efficiency between the shell layers is improved and the resistance to ion transport is further reduced. Moreover, the porous multishell structure provides a buffer space for the shock generated by multiple rapid embedding/de-embedding of OH − ions and offered a stable structure. Interestingly, the number of shell layers, thickness, spacing, and shell density of the N–CCS@NCS nanospheres can be controlled by adjusting the Ni content. Owing to its compositional and structural advantages, the N–CCS@NCS electrode exhibited a high specific capacitance of 1259 F g −1 at 0.5 A g −1 . The assembly N–CCS@NCS//activated carbon asymmetrical supercapacitor exhibited specific energy of 87.3 W h kg −1 at 825 W kg −1 and a capacitance retention rate of 81.3 % after 8400 cycles. Furthermore, the N–CCS@NCS electrocatalyst exhibited outstanding hydrogen precipitation properties (254 mV at 10 mA cm −2 ) in 1 M KOH and excellent stability over 20 h. Therefore, MOF-derived porous multishell metal sulfides are promising candidates for supercapacitor and hydrogen evolution reaction dual applications.
✓ 已验证
产品关联
DOI
高影响因子
Polymers
·
2022
·Vol. 14
·期 19
·3941
·
IF 4.967
Xu Gao,Jun-Feng Su,Sai Wang,Peng Yang
Artificial skin composites have attracted great interest in functional composite materials. The aim of this study was to prepare and characterize a smart artificial skin composite comprising a bionic microvascular with both self-nourishing and self-healing functions. A poly(vinyl alcohol)–glycerol–gelatin double network organic hydrogel was used as the artificial skin matrix. The hydrogel had high mechanical strength because of the strong hydrogen bond formed between the PVA and glycerol (GL). The gelatin (GEL) increased the toughness and elasticity of the hydrogel to ensure the strength of the artificial skin and fit of the interface with the body. The bionic polyvinylidene fluoride (PVDF) microvascular had excellent thermal stability and mechanical property in artificial skin. Results indicated that self-nourishing was successfully realized by liquid release through the pore structures of the bionic microvascular. The bionic microvascular healed microcracks in the artificial skin when damage occurred, based on a self-healing test.Keywords:artificial skin;self-nourishing;self-healing;microvascular
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF PHYSICAL CHEMISTRY B
·
2022
·
IF 3.466
Jianfeng Xue,Zheng Wang,Hong Zhang,Yan He
Viscoelastic characterization is of great importance for the investigation of biomolecular condensates. Single-particle-tracking-based rotational diffusion analysis of single nanorods is an effective approach for quantitative viscosity measurement. However, in the case of high background and noise with high-speed image acquisition, accurate extraction of diffusivity from the data is a challenging task. Here, we develop a novel frequency-domain-based deep learning (DL) method for single nanorod rotational tracking analysis. We synthesized Brownian rotational time-series data for training, designed a data preprocessing module to reduce the effect of noise, and extracted rotational diffusion coefficient using recurrent neural networks in the frequency domain. Compared with the traditional curve-fitting-based methods, our method shows higher accuracy and a wider detection range for viscosity measurement. We verified our method using experimental data from plasmonic imaging of single gold nanorods (AuNRs) in glycerol solution and PGL droplets. Our method can be potentially applied to the viscosity measurement of different biomolecular condensates in vitro and in vivo.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING
·
2022
·
IF 9.463
Qiyuan Li,Lin Cao,Wei Wang,Xude Qin,Shougang Chen
In this paper, polyurethane (PU) with polyethylene glycol as a soft segment and isophorone diisocyanate as a hard segment were designed and synthesized. Copper complex (Cu(HD) 2 ) was synthesized in PU preparation, bringing excellent self-healing, photothermal and antibacterial properties. The content of Cu 2+ accounted for less than 2wt% of PU elastomer. Cu(HD) 2 acted as a chain extender and provided coordination bonds for elastomer to promote the self-healing process. Experiments showed that Cu(HD) 2 exhibited excellent photothermal properties in PU. The maximum temperature of the samples after 5 min irradiation under a sunlight simulator could reach 120 °C. The results of the self-healing experiment showed that mechanical properties of PU could be recovered by nearly 90%, and electrochemical protection performance could be recovered by nearly 100%. Antibacterial experiments proved that PU could release Cu 2+ , forming an antibacterial ring around PU. PU has excellent application in the field of anticorrosion and antibacterial coatings.
✓ 已验证
产品关联
DOI
高影响因子
MOLECULES
·
2022
·Vol. 27
·期 18
·5985
·
IF 4.927
Yuqin Zhang,Shiquan Bian,Jing Hu,Gang Liu,Shouhua Peng,Hongjiang Chen,Zhenying Jiang,Tongyong Wang,Quan Ye,Haibo Zhu
Natural deep eutectic solvents (NADESs) coupled with microwave-assisted extraction (MAE) were applied to extract total flavonoid compounds from spent sweet potato (Ipomoea batatasL.) leaves. In this study, ten different NADESs were successfully synthesized for the MAE. Based on single-factor experiments, the response surface methodology (RSM) was applied, and the microwave power, extraction temperature, extraction time, and solid–liquid ratio were further evaluated in order to optimize the yields of total flavonoid compounds. Besides, the extracts were recovered by macroporous resin for the biological activity detection of flavonoid compounds. As a result, NADES-2, synthesized by choline chloride and malic acid (molar ratio 1:2), exhibited the highest extraction yield. After that, the NADES-2-based MAE process was optimized and the optimal conditions were as follows: microwave power of 470 W, extraction temperature of 54 °C, extraction time of 21 min, and solid–liquid ratio of 70 mg/mL. The extraction yield (40.21 ± 0.23 mg rutin equivalents/g sweet potato leaves) of the model validation experiment was demonstrated to be in accordance with the predicted value (40.49 mg rutin equivalents/g sweet potato leaves). In addition, flavonoid compounds were efficiently recovered from NADES-extracts with a high recovery yield (>85%) using AB-8 macroporous resin. The bioactivity experiments in vitro confirmed that total flavonoid compounds had good DPPH and O2−· radical-scavenging activity, as well as inhibitory effects onE. coli,S. aureus,E. carotovora, andB. subtilis. In conclusion, this study provides a green and efficient method to extract flavonoid compounds from spent sweet potato leaves, providing technical support for the development and utilization of sweet potato leaves’ waste.Keywords:natural deep eutectic solvents;response surface;spent sweet potato leaves;antioxidant activity
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CHEMOSPHERE
·
2022
·
IF 8.943
Zhongbao Ma,Long-Fei Ren,Diwen Ying,Jinping Jia,Jiahui Shao
The separation of hardness ions such as calcium and magnesium from hard water can improve water quality, which is important but technically challenging. Nanofiltration (NF) has attracted much attention because of its efficiency, environmental friendliness and low cost. However, common NF membranes with a singly (either positively or negatively) charged layer have insufficient water softening capacity. In this work, two types of dual-layer Janus charged polyamide NF membranes composed of oppositely charged inner and outer layers were developed for the first time by sequential electrospray polymerization strategy for efficient water softening. The effect of the microstructure of the dually charged barrier layer on the separation performance of divalent salt ions was explored. Detailed mechanistic studies revealed that the microstructure of the outer layer of the barrier layer played a crucial role in the ion separation of the Janus membrane due to its control of the reverse transport of ions. Janus charged polyamide NF membrane with a loose outer layer exhibited better water softening performance (93.6% of hardness removed) compared to the singly charged NF membranes due to the simultaneous dual electrostatic effect and no ion reverse transport confinement. This Janus charged NF membrane also possessed good antifouling performance, mainly due to its negatively charged outer layers. The mechanistic insights gained in this study reveal the huge potential of microstructural design toward high-performance Janus charged NF membranes, and provide important guidance on the future development of high-efficiency water softening NF membranes.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2022
·
IF 16.744
Yan-Bin Li,Zhang-Nan Wen,Han-Zhuo Xu,Guang-Wen Chu,Liang-Liang Zhang,Jian-Feng Chen
Rotating packed beds (RPBs) achieved notable application progress in high-viscosity processes. Mass transfer modeling for viscous fluids, laying the foundation for application research, was a significant and urgent challenge in RPBs. In our previous works, a disk-distributor RPB (DRPB) for facilitating high-viscosity processes was put forward by replacing the conventional nozzle distributor with a disk distributor. The basic flow parameters of viscous fluids in the DRPB have been obtained, involving liquid holdup, wetting efficiency, flow patterns, and liquid element characteristics. In the present study, a liquid-side volumetric mass transfer coefficient model for viscous fluids (143–15259 mPa·s) was further developed based on penetration and surface renewal theories. Via comprehensive analyses of the abovementioned flow characteristics, key model parameters were determined, including the specific area of liquid and the volume fraction of different flow patterns in packing. The experiments of devolatilization from viscous solutions were implemented to examine the mass transfer model. The deviation between the model-predicted and experimental acetone removal efficiencies was within + 15 % and −10 %, proving the reasonability of the mass transfer model.
✓ 已验证
产品关联
DOI
高影响因子
FOOD HYDROCOLLOIDS
·
2022
·
IF 11.504
Danmin Yang,Qun Liu,Yahui Gao,Shoumei Wan,Fanrong Meng,Wuyin Weng,Yucang Zhang
Sliver nanoparticles (AgNPs) were loaded on chitosan (CS) and incorporated into polyvinyl alcohol (PVA) to develop novel active food packaging films. AgNPs were fabricated by liquid phase chemical reduction method using CS and sodium citrate friendly reductant of AgNO 3 . The silver we prepared was found to be nanoscale by transmission electron microscopy (TEM) and AgNPs were homogeneously dispersed in the matrix by scanning electron microscopy (SEM). The composite film exhibited excellence mechanical properties with tensile strength of 49.97 MPa and elongation at break of 275.90%. When the concentration of AgNPs was 0.019% (w/w), the diameter of filter paper was 5.00 mm and the inhibition zone against Escherichia coli reached 16.07 mm at 37 °C for 8 h. The water vapor permeability and water solubility of the Ag@CS/PVA films decreased with the incorporation of AgNPs, and this was beneficial for food preservation. Especially, Ag@CS/PVA films could reduce the weight loss of strawberries and avoid microbial infection at 25 ± 1 °C and 50 ± 5% RH. Benefiting for good mechanical properties, antibacterial property, flexibility and high transparency, Ag@CS/PVA films showed its great potential in fruit storage and transportation application.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2022
·
IF 16.744
Qirui Wu,Songjiu Han,Jundong Zhu,Anbang Chen,Jiayu Zhang,Zhen Yan,Jiantao Liu,Jianren Huang,Xiaoxiang Yang,Lunhui Guan
Soft ionic conductors (ICs) such as hydrogels and ionogels have attracted extensive attention as they are promising candidates as the key components used in flexible electronic devices. Nonetheless, hydrogels and ionogel-based materials reported by previous studies usually exhibit prominent problems, such as solvent leakage and evaporation, limiting their application in complex environment. In this work, solid-state conductive ionogels (SCIg) composed of long-chain copolymer networks without any volatile liquids were designed and prepared. The dynamic non-covalent bonds ensure its long-term stable signal monitoring as a sensor. The SCIg shows extraordinary comprehensive properties, including admirable tensile strength (0.97 MPa) under large deformations (λ = 26.6 tensile stretch), promising conductivity (56.1 mS m −1 ) and surprising self-healing efficiency (>95 %). Notably, the SCIgs solved a well-established problem in ionogels, namely the conflict of ionic conductivity versus mechanical properties. Moreover, a series of ionoelastomers based on the SCIg were further exploited as a resistance-type sensor, capacitive-type sensor and multifunctional electronic skins capable of detecting a variety of mechanical signals. The sensors deliver splendid long-term stability with signal responses. Meanwhile, the obtained SCIgs exhibit high efficiency ultraviolet (UV) curable 3D printability, enabling the bulk production of microcircuits with 130 μm diameter in a transitory time. This work shows that the developed SCIg presents great application potential in the fields of electronic skin, physiological signal detection and human–machine interface.
✓ 已验证
产品关联
DOI
高影响因子
MACROMOLECULAR BIOSCIENCE
·
2022
·Vol. 23
·期 1
·2200275
·
IF 5.859
Yuru Chen,Jian Song,Song Wang,Weiqiang Liu
Poly(vinyl alcohol) (PVA) hydrogel is a promising candidate for articular cartilage repair yet restrained by its mechanical strength and tribological property. Current work reports a newly designed PVA-based hydrogel modified by glycerol (g), bacterial cellulose (BC), and a cationic polymer poly (diallyl dimethylammonium chloride) (PDMDAAC), which is a novel cationic strengthening choice. The resultant PVA-g-BC-PDMDAAC hydrogel proves the effectiveness of this modification scheme, with a confined compressive modulus of 19.56 MPa and a friction coefficient of 0.057 at a joint-equivalent load and low sliding speed. The water content, swelling property, and creep behavior of this hydrogel are also within a cartilage-mimetic range. The properties of PVA-based hydrogels before PDMDAAC addition are likewise studied as a cross-reference. Besides, PDMDAAC-modified PVA hydrogel realizes ideal mechanical and lubrication properties with a relatively low PVA concentration (10 wt.%) and facile fabrication process, which lays a foundation for mass production and marketization in the future.
✓ 已验证
产品关联
DOI
PubMed
高影响因子