FUEL
·
2023
·
IF 7.4
Muhammad Yousaf,Yuzheng Lu,Majid Niaz Akhtar,Ali Sarosh Khawaja,Khalid Mujasam Batoo,Sajjad Hussain,Asma Noor,Muhammad Akbar,Hu Enyi,M.A.K Yousaf Shah,Naveed Mushtaq,Bin Zhu
Lattice defects in rare earth (RE) doped single-phase semiconductor materials play a key role in structural modifications and physicochemical characteristics, resulting to enhance the ionic conductivity. In this work, we synthesized lanthanum doped samarium oxide with different mole ratios and applied it as a ceramics membrane fuel cell device to enable high peak power density (PPD) at low operational temperatures (520–400 °C). The samples are capable of triple charge H + /O 2− /e − conduction and enhance the catalytic function of the cell in terms of HOR and ORR kinetics by producing lattice defects. The fabricated Sm 1.5 La 1.5 Fe 5 O 12 (2-SLFO) fuel cell device exhibits a high OCV of 1.13 V with a maximum PPD of 864.26 mW/cm 2 at 520 °C. Durability measurement verifies that 2-SLFO-based fuel cell device can be worked for 60 h under fuel cell conditions (H 2 /air) at 520 °C. The first principle calculations using density functional theory (DFT) demonstrate that the higher oxygen vacancy concentration in the 2-SLFO sample may cause to the higher charge-transfer kinetics, subsequent in the enhancement of ions transportation of the fabricated fuel cell device.
研究领域:
材料科学
·
电化学
·
能源材料
·
固态离子学
·
燃料电池技术
✓ 已验证
DOI
高影响因子
APPLIED CATALYSIS A-GENERAL
·
2024
·
IF 4.7
Chenyang Zhao,Yujia Liu,Yupeng Tian,Yahui Li,Junjie Feng,Wei Xu,Ning Shi,Zhe Yang,Bing Sun
Direct epoxidation of propylene (C 3 H 6 ) with hydrogen (H 2 ) and oxygen (O 2 ) over Au/TS-1 catalyst was promising way for the synthesis of propylene oxide (PO). However, high selectivity of PO (>95 %) and conversion of C 3 H 6 (>5 %) cannot be achieved at the same time. The industrialization process was severely restricted. In this paper, Au/TS-1 catalysts were synthesized by deposition precipitation method with alkali metal promoter. And alkaline gases and silane coupling post-treatment were performed to promote the catalytic activity. The prepared samples exhibited a much better C 3 H 6 conversion (6.5 %) and PO selectivity (95.1 %) compared with general catalyst using normal synthetic technology. Cs 2 CO 3 was beneficial to increasing Au nanoparticles uptake efficiency. Both NH 3 and triethoxyvinylsilane post-treatment were good for smaller and more uniform loading of Au nanoparticles. The decreasing in surface hydroxyl density effectively alleviated the occurrence of PO ring opening isomerization. The increased hydrophobicity of TS-1 surface was conducive to the rapid desorption of generated PO and significantly increased PO selectivity. Multiple pretreatment was also favorable for extending the lifetime of Au/TS-1 catalyst.
研究领域:
催化化学
·
材料科学
✓ 已验证
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2023
·
IF 8.6
Lidan Xie,Wenyi Huang,Guoqiang Jiang,Yi Liu,Mude Zhu,Yi Tang,Xueqin Chen,Xiaoyun Fan
The wide occurrence of metronidazole (MNZ) in aquatic environment has aroused increasing concern to the potential adverse effects on human health. Combining different motifs into a photolytic material to achieve high photocatalytic efficiency is regarded as one of the main strategies during photocatalytic process. Herein, a triple anions contained photocatalyst , Ba 3 (BO 3 )(CO 3 )F (BBCF), exhibited excellent removal efficiency of MNZ (92.6%) in 15 min, which was 5.87 times higher than that of commercial P25. The excellent removal efficiency could be attributed to the strong electronegativity of the F − , and the π-conjugated triangles structure of (BO 3 ) 3− and (CO 3 ) 2− , which made BBCF facilitate the transport of photogenerated electrons, thus accelerating the accumulation of active h + . Meanwhile, the appropriate reduction potential of BBCF accounted for the outstanding productivity of O 2 – . h + and O 2 – were proved as the dominant reactive species for MNZ degradation. The degradation products were analyzed by LC-TOF-MS, and the toxicity of the intermediate was evaluated to be lower than that of parent MNZ molecule. Moreover, BBCF showed the universal application of degrading oxytetracycline (OTC), methylene blue (MB). Therefore, anion-rich BBCF catalyst with high catalytic activity has a potential application prospect for degrading harmful pollutants in practical water environment.
研究领域:
环境科学
·
材料科学
·
化学工程
✓ 已验证
DOI
高影响因子
Advanced Science
·
2026
·
IF 14.1
Zesheng Chen,Yanchao Yu,Xingyuan Xiao,Wenwen Cheng,Ye Yang,Zhengyao Zhang,Wang Wang,Zhijun Zhou,Weikang Hu,Xiaolong Wang,Bing Li,Kwang Leong Choy,Yun Chen,Zijian Wang
Impaired wound healing in diabetes is closely associated with cellular ferroptosis. Microneedle-assisted gas therapy exerts molecular regulation of ferroptosis, representing a promising approach for accelerating diabetic wound healing. To date, O 2 and H 2 gas therapies have consistently been conducted independently and have never been integrated into a single system. Whether and how their synergy might be realized remains a defining challenge. Herein, we propose a concept of integrated O 2 and H 2 gas therapy, demonstrated by fabricating a gas-producing microneedle material. Platinum@MIL-101(Fe)-NH 2 @phosphotungstic acid (PMP) nanoparticles are synthesized as a visible light-driven photocatalyst for H 2 and O 2 co-evolution. The rational design of a spatially separated structure boosts their photocatalytic efficiency under physiological conditions. PMP nanoparticles are further incorporated with bilayer gelatin methacryloyl (GelMA)/PMP composite microneedles (denoted as GPM microneedles). The obtained GPM microneedles enable transdermal delivery of PMP nanoparticles for integrated O 2 and H 2 gas therapy, and demonstrate desirable biocompatibility and pro-regenerative effects. The mechanism of integrated O 2 and H 2 gas therapy has been identified as a TNFAIP3/hnRNPA1 ubiquitination/ferroptosis signaling axis, establishing for the first time a direct link to ferroptosis. In conclusion, this study yields a transformative concept and a ferroptosis-targeting microneedle material with well-defined molecular mechanism for diabetic wound management.
✓ 已验证
产品关联
DOI
高影响因子
BIOSENSORS & BIOELECTRONICS
·
2025
·
IF 10.5
Xiaobo Zhang,Xiuwen Wang,Longjiao Zhu,Jinyan Zhu,Qiuyue Zheng,Jingli Yuan,Wentao Xu,Jijuan Cao
Salmonella typhimurium ( S. typhimurium ), as common and highly pathogenic foodborne pathogen, poses a significant risk to public safety worldwide. The development of highly sensitive, rapid and on-site method for S. typhimurium analysis is urgently needed to prevent bacterial infections. Herein, we introduced a CRISPR/Cas12a-driven electrochemiluminescence (ECL) sensor based on luminol/O 2 binary systems for S. typhimurium detection, employing ultrafine Pt nanoclusters-anchored 2D delaminated-MXenes (Pt NCs/D-MXenes) as the co-reactant accelerator. The ultrathin D-MXenes support regulates the size and dispersibility of Pt NCs and facilitates the full exposure of active sites, and synergistic interactions between D-MXenes and Pt NCs improves electrocatalytic properties toward the reduction of O 2 , which promotes the generation of ROS for boosting ECL emission. Using target responsive-regulated CRISPR/Cas12a system, the ECL sensor for S. typhimurium showed a broad concentration range from 10 1 to 10 6 CFU/mL and limit of detection of 6 CFU/mL, with satisfactory recoveries in spiked-actual samples.
研究领域:
生物技术
·
食品安全
·
分析化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ACTA PHYSICO-CHIMICA SINICA
·
2025
·
IF 13.5
Yanyan Zhao,Zhen Wu,Yong Zhang,Bicheng Zhu,Jianjun Zhang
Photocatalytic oxygen reduction reaction (ORR) offers a mild and cost-effective approach for hydrogen peroxide (H 2 O 2 ) production. However, its practical application is significantly hindered by rapid charge carrier recombination and insufficient O 2 adsorption capacity in photocatalysts. To address these limitations, we developed a strategy involving the creation of S-vacancy-rich CdIn 2 S 4 (S v –CIS) to facilitate charge separation and subsequent deposition of Au nanoparticles on its surface (Au–S v –CIS) to strengthen O 2 adsorption. The results suggest that the optimized Au–S v –CIS achieves a significantly increased H 2 O 2 production yield of 2542 μmol·h·g −1 in 10%-ethanol/water solution, which is about 12.8 and 1.7 times higher than that of pure CIS and S v –CIS. Comprehensive characterizations including photoluminescence spectra, time-resolved photoluminescence spectra, transient photocurrent response, electrochemical impedance spectra, and femtosecond transient absorption spectroscopy confirm the improved charge dynamics of Au–S v –CIS. In addition, temperature-programmed desorption of O 2 combined with density functional theory calculations conclusively demonstrates the superior O 2 adsorption capacity of Au–S v –CIS. This work provides a design strategy for efficient solar–to–chemical energy conversion through cooperative photocatalyst engineering.
研究领域:
光催化
·
纳米材料
·
能量转换
·
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
Energy & Environmental Materials
·
2025
·
IF 14.1
Zhengcai Zhang,Dulin Huang,Xiaohui Peng,Zhang Zhang,Yaying Dou,Zhen Zhou
Redox mediators (RMs) represent the most promising strategy to address the sluggish kinetics of lithium–oxygen (Li–O 2 ) batteries. To achieve high-energy and cost-effective Li–O 2 batteries, carbon materials are typically regarded as ideal cathodes in these systems. However, the impact of their surface properties—which often regulate specific discharge pathways—on the RM-mediated oxygen reduction reaction (ORR) remains unclear. In this study, CNTs electrodes with different surface properties are fabricated. Results suggest that CNTs with more surface defects not only promote the unmediated discharge pathway even in RMs-involved battery systems but also exacerbate the corrosion of carbon cathodes. This, in turn, leads to the undesired accumulation of Li 2 O 2 and Li 2 CO 3 on the cathode surface, which hinders effective and continuous electron transfer between the cathode and RMs, ultimately decreasing the catalytic activity of RMs. As a result, the discharge capacity of the battery is seriously diminished, especially at large current densities. These findings underscore the significance of surface engineering in advancing the performance of RMs-assisted Li–O 2 batteries.
研究领域:
电化学
·
材料科学
·
储能技术
·
表面工程
·
电池技术
✓ 已验证
产品关联
DOI
高影响因子
Nano Materials Science
·
2025
·
IF 17.9
Hongjing Liu,Shan Ren,Xiaodi Li,Liang Wang,Bofeng Bai,Shouning Chai,Peng Chen,Fan Dong
Photocatalytic oxidation of nitrogen oxides (NO x ) is a promising technology for environmental protection and green sustainable development. However, its practical application remains limited due to inefficient activation of NO and O 2 , stemming from inadequate structural design of photocatalysts. Herein, we developed a thin-layer two-dimensional (2D) material Bi 2 MoO 6 (BMO) via cetyl trimethyl ammonium chloride (CTAC) addition in synthesis process, which effectively modulates the surface electronic structure, enhance the light absorption and activation of NO and O 2 . This thin-layer Bi 2 MoO 6 nanosheets achieved a NO oxidation efficiency of 45.3 %, which was about 5.5 times that of traditional bulk BMO (8.2 %). Additionally, it demonstrated superior selectivity for NO 2 − /NO 3 − production (86.6 %) compared to bulk BMO (60.5 %) and significantly reduced the formation of toxic NO 2 byproducts (13.4 % vs. 39.5 %). Combining experimental characterizations and density functional theory (DFT) simulations, it demonstrated that the electron-hole pair separation could be promoted and targeted adsorption activation of O 2 can be enhanced to form superoxide radicals (•O 2 − ) and singlet oxygen ( 1 O 2 ) via the effect of surface charge transfer adjustment on the thin-layer structure of Bi 2 MoO 6 , which are key factors affecting the efficiency and selectivity of photocatalytic oxidation of NO. This work provides important insights into the formation of directed ROS and proposes a unique mechanism for selective NO oxidation.
研究领域:
环境科学
·
材料科学
·
光催化
·
化学工程
·
理论化学
✓ 已验证
产品关联
DOI
高影响因子
Joule
·
2022
·
IF 46.048
Qing Han,Wei Guo,Xiaofeng He,Tongchao Liu,Xiao Liu,Xuebing Zhu,Tengfei Bian,Lei Jiang,Jun Lu,Yong Zhao
Aprotic lithium-oxygen (Li-O 2 ) batteries have attracted extensive attention due to their ultrahigh theoretical energy density. However, slow and undesired electron transfer during cathodic reactions causes low cyclic stability in these batteries. Here, we demonstrate that O 2 mass transport and electron transfer for cathodic reactions in Li-O 2 batteries could be decoupled by a double-cathode structure that efficiently enables stable electron transfer between the cathode and Li 2 O 2 /O 2 . This resolves various side reactions and slow Li 2 O 2 reaction kinetics issues in conventional Li-O 2 batteries, leading to stable operation of the cell for nearly 2 months at a capacity of 0.2 and 5 mAh cm −2 , with more than 4- and 10-fold increases in cycle life when compared with single-cathode batteries. These remarkable improvements in the cyclic stability of Li-O 2 batteries with double cathodes provide an interesting concept for improving the operational stability of other metal-rechargeable batteries with conversion-type chemistry.
研究领域:
电化学
·
材料科学
·
能源存储
✓ 已验证
DOI
高影响因子
ENVIRONMENTAL SCIENCE & TECHNOLOGY
·
2025
·
IF 11.3
Jingwen Qian,Mingyi Yu,Zheng Lian,Shule Zhang,Qin Zhong
An innovative strategy in wet flue gas denitration technology was proposed to control nitrogen oxide emissions from cement kiln. Here the use of tetrabutylammonium bromide (TBAB) as an additive improved the absorption and utilization efficiency of sulfite absorbents for NO2. Compared with the sulfite solution, the stability time and absorption efficiency of adding TBAB were increased from 25 to 76 min and from 91.2 to 98.4%, respectively. Continuous absorption for 480 min indicated the feasibility of TBAB for repeated use. Moreover, we propose an antioxidant mechanism, including the capture of SO3•– by TBA+, and the reduction of SO3•– by Br–. The successive steps kept the sulfite from the cyclic depletion of the radical chain reaction of “Generate SO3•–-Introducing O2–Consuming SO32–” due to O2. A new application of TBAB in free radical trapping and antioxidant is given. Furthermore, a kinetic model describing the macroscopic absorption rate was developed based on different operating conditions.
研究领域:
环境化学
·
化学工程
·
物理化学
·
大气污染控制
·
工业生态学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ADVANCED FUNCTIONAL MATERIALS
·
2021
·Vol. 32
·期 15
·2111125
·
IF 18.808
Binyao Liu,Jinyan Du,Gaili Ke,Bi Jia,Yujie Huang,Huichao He,Yong Zhou,Zhigang Zou
g -C 3 N 4 photocatalysis is a safe and green approach for H 2 O 2 production, but the activity of pristine g -C 3 N 4 photocatalysts is unsatisfactory. At present, most of the modifications on g -C 3 N 4 photocatalysts for H 2 O 2 production have focused on thermodynamic processes, few have considered the kinetic aspects. Herein, the surface N -hydroxymethylation of g -C 3 N 4 photocatalysts for the efficient kinetic production of H 2 O 2 is reported. Through the reaction of formaldehyde with the amino moieties (–NH 2 ) on the g -C 3 N 4 surface, N -hydroxymethyls groups (-NH-CH 2 -OH) are introduced on typical g -C 3 N 4 photocatalysts. Relative to the pristine g -C 3 N 4 photocatalysts, the modified g -C 3 N 4 photocatalysts have over 1280% higher activity for H 2 O 2 production in pure water system, and impressive solar-to-chemical conversion efficiency. The experimental investigations and theoretical calculations reveal that the introduction of -NH-CH 2 -OH on the g -C 3 N 4 photocatalysts does not change their morphology, light absorption intensity and edges, band positions, charge separation and transfer properties, but markedly improved the H 2 O dehydrogenation and O 2 adsorption properties of g -C 3 N 4 . As a result, the reduction kinetics of O 2 to H 2 O 2 on the g -C 3 N 4 photocatalysts with -NH-CH 2 -OH is more energetically favorable. This work provides a useful reference and inspiration to achieve the effective modification of g -C 3 N 4 or other metal-free photocatalysts from the kinetic perspective.
研究领域:
光催化
·
材料科学
·
化学动力学
·
可再生能源
·
环境化学
✓ 已验证
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2025
·
IF 8.2
Yingnan Zhu,Jiahang Si,Tiantian Xu,Lan Zheng,Xinyu Xiao,Xiaohan Sun,He Ding,Yuze Dong
Chemodynamic therapy (CDT) and photodynamic therapy (PDT) have emerged as promising strategies for treating skin abscesses. However, their therapeutic efficacy is fundamentally constrained by the hypoxic and hydrogen peroxide-deficient microenvironment characteristic of abscesses. Herein, we developed a near-infrared (NIR) light-responsive nanoplatform (ICG/CuO2@PCM) by encapsulating copper peroxide (CuO2) and indocyanine green (ICG) within a phase-change material (PCM), which enables control over self-supplied H2O2/O2 release via an NIR-triggered cascade. Upon irradiation, ICG-mediated photothermal conversion elevates the temperature beyond the PCM melting threshold, triggering a burst release of CuO2 and ICG. CuO2 generates hydroxyl radicals (•OH) through a Fenton-like reaction in the acidic wound microenvironment. Additionally, CuO2 can thermally decompose under photothermal conditions to produce a sustained oxygen supply, which ICG immediately converts into singlet oxygen (1O2), thereby enhancing PDT efficiency. Furthermore, photothermal therapy not only enhances the efficiency of CDT but also provides additional antibacterial support. Remarkably, ICG/CuO2@PCM (NPs), coupled with irradiation, accelerate abscess wound recovery by dispersing biofilm, killing bacteria, and promoting macrophage polarization toward an anti-inflammatory phenotype. Overall, this NIR-responsive nanoplatform highlights the promise in controlled modulation of microenvironment-adaptive antimicrobial strategies to overcome current limitations of hypoxic infections.
研究领域:
生物医学工程
·
纳米医学
·
感染性疾病治疗
·
抗菌治疗
·
转化医学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）