CHEMICAL ENGINEERING JOURNAL
·
2018
·
IF 6.735
Jing Zhou,Dapeng Li,Shutong Chen,Yao Xu,Xue Geng,Chaoran Guo,Yong Huang
The immobilization of sedimentary phosphorus (P) by capping sediments with amended calcium peroxide material (ACPM) and CaO 2 was investigated, the sediments and overlying water from a black-odor river. Under the capping with ACPM and CaO 2 , the pH and dissolved oxygen (DO) in the overlying water were higher than in the control. This contributed to the more loss of external P under the ACPM (the phosphate sorption was fitted well by the Langmuir equation, the maximum P sorption capacity up to 29.28 mg P g −1 ). Additionally, ACPM improves the decrease of the reduction materials (e.g., NH 4 + -N, Fe 2+ ) in the pore water compared to that associated with CaO 2 , resulting in a less obvious dissolved inorganic P (DIP) in the pore water, but the accumulation of DIP in the pore water with CaO 2 suggested an explosive release once the micro-environment conditions encounters adverse conditions. The sharp reduction of Fe/Al-P and Res-P contributes to the increase of DIP in the pore water, with a release of up to 390.60 mg P kg −1 DW (dry weight), whereas the value is only 62.55 mg P kg −1 DW when capped with ACPM. Correspondingly, the percentage of the bioavailable P to Tot-P decreases rapidly from 17.27% (control, 0–2 cm) to 7.21% (ACPM, 0–2 cm) and 10.57% (CaO 2 , 0–2 cm), indicating the obvious P immobilization. The implication is that the application of CaO 2 is not suitable for direct use, while the combination with other materials (e.g., WPS) is a better choice.
研究领域:
环境科学
·
水体修复
·
环境化学
·
污染控制
·
沉积物管理
✓ 已验证
DOI
高影响因子
POLYMERS FOR ADVANCED TECHNOLOGIES
·
2015
·Vol. 26
·期 8
·953-959
·
IF 1.757
Shuting Wang,Lan Cen,Qihao Wu
Maleated glycidyl 3-pentadecenyl phenyl ether with styrene (MGS) was synthesized from glycidyl 3-pentadecenyl phenyl ether (GPPE), maleic anhydride (MAH) and styrene (St) in the presence of AIBN initiator at 80°C, and then the resultant MGS was applied as a compatibilizer to prepare SBR/silica composites. Meanwhile, the commercial compatibilizer bis-(triethoxysilylpropyl) tetrasulfide (named Si69) added into composite was also prepared for comparison purpose. The synthetic MGS structure was characterized by GPC and FTIR, and SBR/silica compounds with different compatibilizer were analyzed using RPA, DMA and so on. The results showed that M̄n and M̄w of MGS were 19,538 g/mol and 23,790 g/mol, respectively. The curing time of compounds with MGS increased, whereas the maximum and minimum torques decreased. The addition of MGS decreased Payne effect of SBR/silica compounds, which implied an improvement of silica dispersion in the compounds. Bound rubber content of compound with MGS was about 1.7 times higher than the absence and 1.5 times higher than that with Si69. The tensile strength of the composites was improved by increasing compatibilizer loading, and the optimum value was observed at 6 phr of MGS. Meanwhile the use of MGS can improve the anti-aging property of composite. According to DMA, the tanδ value at 0°C of composite with MGS was higher than composite without compatibilizer suggesting that MGS can improve the wet skid resistance of composite. The SEM analysis revealed that introduction of MGS enhanced the compatibility between SBR and silica. Copyright © 2015 John Wiley & Sons, Ltd.
研究领域:
高分子化学
·
橡胶复合材料
·
材料界面科学
·
功能高分子
·
聚合物改性
✓ 已验证
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2013
·Vol. 129
·期 4
·2313-2320
·
IF 1.395
Mingchao Luo,Xiaoxue Liao,Shuangquan Liao,Yanfang Zhao
Waste rubber powder (WRP) was modified by microwave, sol–gel method, and both microwave and sol–gel method, respectively. The mechanical and dynamic mechanical properties of natural rubber (NR)/modified WRP composite were investigated. The influence of bis-(3-(triethoxysilyl)-propyl)-tetrasulfide (TESPT) content on curing characteristics and mechanical properties of vulcanizate was also studied. The results showed that NR/WRP modified by both microwave and sol–gel method composite owned the best mechanical properties. Rubber processing analyzer was used to characterize the interaction between silica and rubber chains and the dispersion of silica. With increase of TESPT content, the Payne effect decreased. Scanning electron microscopy indicated the coherency and homogeneity of in situ generated silica filled vulcanizate. Dynamic mechanical analyzer showed that NR/WRP modified by both microwave and sol–gel method composite with 5 phr TESPT exhibited the lower tan δ at temperature range of 50–80°C, compared with composite without TESPT and the higher tan δ at temperature of 0°C, compared with the conventional modification of WRP. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013
研究领域:
高分子材料科学
·
橡胶工程
·
复合材料学
·
材料化学
·
高分子物理
·
功能材料
·
可持续材料技术
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2021
·
IF 13.273
Shujuan Lian,Xiaoshuang Shi,Mingyi Lu,Mengdan Zhang,Xiaohuan Dong,Xu Li,Quan Feng,Rongbo Guo
Due to the persistence in residue and the emission to environment, antibiotics have become the emerging contaminants. Tetracyclines, as the largest amount of antibiotics in the breeding industry, were investigated in this study. For eliminating the tetracyclines, anaerobic culture was enriched from livestock waste after four generations and FeOn(OH)m modified oyster shell powders (OSPs) were amended into the enrichment culture as auxiliary method. Tetracycline and oxytetracycline were selected as the model compounds. The adsorption models (Langmuir and Freundlich isotherms) of tetracycline and microbes on OSPs were simulated respectively. With the addition of FeOn(OH)m modified OSPs, the transformation efficiency of oxytetracycline achieved 81.5% after 22 days’ incubation, approximately 1.85 times higher than the 4th generation (G-IV) enrichment culture without modified OSPs. Dehydration, demethylation, dehydroxylation and decarboxylation took place under anaerobic condition, inferred from the detected metabolites transformed from oxytetracycline. Genus Methanosarcina and two operational taxonomic units (OTUs) assigned to order Clostridiales , showed an increasing trend on abundance, indicating the contribution to transformation of oxytetracycline. Therefore, the FeOn(OH)m modified OSPs and enrichment culture can accelerate the transformation of oxytetracycline simultaneously, indicating a promising utilization not only for waste water system but also for antibiotic contaminated biomass treatment.
研究领域:
环境微生物学
·
污染物生物降解
·
环境工程
·
抗生素去除
·
吸附材料
·
厌氧消化
·
药物代谢
✓ 已验证
DOI
高影响因子
JOURNAL OF MEMBRANE SCIENCE
·
2013
·
IF 4.093
Qiang Xu,Yang Yang,Jie Yang,Xiaozu Wang,Zhaohui Wang,Yong Wang
Conformal and smooth TiO 2 thin layers were coated on the surface of porous PTFE membranes subjected to a plasma activation process by atomic layer deposition (ALD). In contrast, TiO 2 was deposited on the PTFE surface as globular particulates without plasma activation due to the inert chemical nature of PTFE surface. X-ray photoelectron spectrometry confirmed the formation of functional groups on the plasma-activated PTFE surface which served as active sites for the homogeneous adsorption and reaction of ALD precursors. Scanning and transmission electron microscopy revealed the uniformity of the deposited layer and the precise control of its thickness by changing ALD cycle numbers. The water contact angle measurement showed that the hydrophobic surface gradually turned to be near superhydrophilic with the increment of ALD numbers. Also, the membrane mean pore size was progressively reduced by simply altering the ALD numbers. At proper deposition conditions , the modified membranes gained an increase of pure water flux of more than 150% and simultaneously a doubled retention compared to the original unmodified membrane. This research provides an efficient approach devoid of any harsh treatments to modifying PTFE membranes for achieving specific functions, which also can be applied to other organic materials especially with chemical inert surface.
研究领域:
材料科学
·
膜科学与技术
·
表面工程
·
高分子化学
·
环境工程
·
纳米科技
✓ 已验证
DOI
高影响因子
CHINESE JOURNAL OF POLYMER SCIENCE
·
2018
·Vol. 37
·期 5
·493-499
·
IF 2.016
Dong Li,Liu Xiang-Dong,Xiong Zheng-Rong,Sheng De-Kun,Zhou Yan,Yang Yu-Ming
Herein, excellent UV-absorbing poly(vinylidene fluoride) (PVDF) membranes were fabricated through the pre-irradiation induced graft polymerization method. The PVDF chains irradiated with 60 Co γ -ray were modified with the polymerizable UV absorber 2-[2-hydroxy-5-[2-(methacryloyloxy)ethyl]phenyl]-2 H -benzotriazole (RUVA-93). The influences of irradiation dose and monomer concentration on the prepared PVDF-g-PRUVA-93 membranes were investigated, and the optimal condition was eventually obtained. The chemical structures of the films were studied by 1 H-NMR, FTIR, and XRD. UV light transmittance and DSC tests were used to characterize the UV-absorbing performance and thermal property of the PVDF films before and after modification. The results proved that the PRUVA-93 side chains were successfully incorporated into the PVDF main chains and the obtained PVDF- g -PRUVA-93 films possessed remarkable UV-absorbing property. The modified membrane made under the optimized experiment condition could completely block the UV light in the range of 200−387 nm. Additionally, the transmittance of the PVDF- g -PRUVA-93 film could be reduced to 0.04% in 280−320 nm, where the light irradiation could damage polymer materials most seriously.
研究领域:
高分子材料科学
·
辐射化学
·
功能薄膜材料
·
紫外线防护
·
膜科学与技术
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2022
·
IF 8.025
Jian Wang,Zhiyu Xun,Chenyang Zhao,Yang Liu,Jiyou Gu,Pengfei Huo
Soy protein isolate (SPI) is one of the most abundant plant proteins in nature. Enormous studies have been carried out on SPI-based materials, however, the application for energy storage devices is still limited due to its fiddly film forming process and lack of electrochemical performance. Herein, we presented a SPI-based polymer electrolyte by grafting modification with the hydrophilic functional monomer acrylamide (AM). The optimized gel polymer electrolyte (GPE) exhibited an excellent ionic conductivity up to 5.10 mS cm −1 , which was greatly higher than gel polymer electrolyte based on original pure SPI (1.84 mS cm −1 ). More significantly, supercapacitors constructed by grafting-modified SPI delivered a specific capacitance of 141.74 F g −1 at 1.0 A g −1 and exhibited high capacitance retention of 95% after 8000 charge−discharge cycles. Beyond that, redox-active polymer electrolyte based on grafting-modified SPI combining with KI enormously improved the energy density of supercapacitor up to 27.52 Wh kg −1 at a current density of 0.5 A g −1 . This work provided a novel and facile strategy to obtain a high-performance SPI-based polymer electrolyte and laid an experimental foundation for the high-value application of SPI in the field of energy storage devices.
研究领域:
材料科学
·
高分子化学
·
能源存储
·
生物基材料
·
电化学
✓ 已验证
DOI
高影响因子
Colloid and Interface Science Communications
·
2019
·
IF 1.87
Gaoqi Wang,Ding Weng,Chaolang Chen,Lei Chen,Jiadao Wang
The aim of the study was to explore the synergistic effects of nanostructure size and surface treatment of TiO 2 coatings on its wettability and bacteria adhesion. The coatings were fabricated by TiO 2 particles with a diameter ranging from 25 nm to 300 nm. The surface wettability of coatings was tuned by chemical treatment. The anti-adhesion property of as-prepared coatings was evaluated with Streptococcus mutans in two types of solutions: phosphate buffer solution (PBS) and PBS with 1 wt% sucrose. The results show that particle size and surface treatment have significant influences on the wettability (with contact angles of 0–160°) and bacterial adhesion. The coating prepared by chemically modified 25 nm particles has a superhydrophobic property, and could inhibit bacterial adhesion in aqueous solutions with sucrose or not. The study also provides a facile, universal and low-cost process to fabricate anti-adhesion coating, which is applicable for diverse of substrates.
研究领域:
生物材料学
·
纳米医学
·
表面科学
·
微生物学
·
口腔生物学
✓ 已验证
DOI
高影响因子
CHEMICAL RESEARCH IN CHINESE UNIVERSITIES
·
2015
·Vol. 31
·期 4
·585-589
·
IF 0.875
Wei Qi,Wang Liyuan
Molecular glass resist has been considered as one of the best choices for a new generation of lithography. In this work, a new type of photoactive compound was obtained by the esterification of tannic acid with 2-diazo-1-naphthoquinone-4-sulfonyl chloride(2,1,4-DNQ-Cl) and ditertbutyl dicarbonate. The new obtained compound possessed both a photosensitive group of diazonaphthoquinone sulfonate(2,1,4-DNQ) and a group of acidolytic protection. Upon the irradiation of the compound under 365 nm light, the former group was photolyzed and converted into indene carboxylic acid along with a small amount of sulfonic acid, which could lead to the deprotection of the latter group. As a result, a novel i-line molecular glass photoresist was formed with the chemical modification of tannic acid. The experimental results show that the modificated compound had a fair solubility in many organic solvents. The lithographic performance of the resist was evaluated on an i-line exposure system with high photosensitivity and resolution as well.
研究领域:
材料科学
·
微纳加工
·
高分子化学
·
光电子学
·
半导体工艺
✓ 已验证
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2021
·Vol. 139
·期 12
·51827
·
IF 3.125
Yuan Li,Lu Zhang,Fayong Li,Ke Wang,Xiaoru Wu,Hailu Liu,Bibo Long,Yang Zhao,Dong Xie,Junjia Chen
The hydrophobic modification of cellulose nanofibers (CNF) was carried out via free radical polymerization using methyl methacrylate (MMA) as the monomer to improve the compatibility between CNF and poly lactic acid (PLA). Followed by the preparation of the novel nanocomposites in combination of the organic montmorillonite and the substrate. The resulting nanocomposites were then coated on paper surface using a cast-coating process in an attempt to improve the barrier properties towards water vapor and oxygen. In addition, the composite films are prepared via a solution casting method. The water vapor transmission rate (WVTR), water vapor permeability (WVP), oxygen transmission rate (OTR), and tensile strength of the as-prepared films were systematically measured. The corresponding results demonstrated that the WVTR, WVP and OTR decreased with the addition of a certain content of MCNF in coatings. 0.2 wt% MCNF is the optimum content, showing the best gas resistance and tensile performance. The lowest value of WVTR and WVP are 10.30 g/(m 2 ⋯24 h) and 3306.58 g⋯μm/(m 2 ⋯24 h) for films with 0.2 wt% MCNF added, which is 88.23% and 26.05% lower than that of PLA composite film without NFC.
研究领域:
高分子材料
·
纳米复合材料
·
包装材料
·
表面涂层
·
生物基材料
✓ 已验证
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2015
·Vol. 133
·期 1
·
IF 1.768
Yao Zhou,Jinliang He,Jun Hu,Bin Dang
Polypropylene (PP)/polyolefin elastomer (POE) blends and MgO/PP/POE nanocomposites were fabricated by melt blending. The morphology, mechanical, and electrical properties of the nanocomposites were investigated. Scanning electron microscopy showed that the surface-modified MgO nanoparticles were well dispersed in the polymer matrix at low loadings of less than 3 phr. X-ray diffraction demonstrated that the crystalline phases of PP in the composites were changed and that the β phase significantly increased. An examination of the electrical properties revealed that the direct-current (dc) electric breakdown strength and space-charge suppression effect were remarkably improved by the introduction of the surface-modified MgO nanoparticles. In addition, obvious enhancements in the tensile modulus and strength were obtained as a result of the synergistic toughening of the POE and MgO nanoparticles. Thus, MgO/PP/POE nanocomposites with enhanced mechanical and electrical properties have great potential to be used as recyclable insulation materials for high-voltage dc cables with large transmission capacities and high operating temperatures. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 132 , 42863.
研究领域:
高分子材料科学
·
电气工程材料
·
纳米复合材料
·
介电物理
·
绝缘材料
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）