CERAMICS INTERNATIONAL
·
2019
·
IF 3.45
Juan Xi,Guohua Chen,Fei Liu,Fei Shang,Jiwen Xu,Changrong Zhou,Changlai Yuan
In view of lead-free low-softening CuO–ZnO–B 2 O 3 –Li 2 O glass, novel glass/Al 2 O 3 ceramic composites were prepared by solid-state reaction route for ultra-low temperature co-fired ceramic (ULTCC) applications. The phase evolution and compositions, microstructure and microwave dielectric properties of the composites were studied by XRD , SEM and dielectric property measurement. Four phases including Cu 2 Al 6 B 4 O 17 , Li 2 CuB 4 O 8 , CuB 2 O 4 and Al 2 O 3 coexist in the glass/Al 2 O 3 ceramic composites sintered in the range of 640–660 °C. However, the contents and types of the phases depend on the composition of the composites and firing temperature. The optimum properties with a permittivity ε r = 3.79, a quality factor Q × f = 38557 GHz (at 16.64 GHz) and a temperature coefficient of resonance frequency τ f ≈0 ppm/ o C as well as a heat conductivity λ = 1.46W(mK) −1 can be achieved for the glass/ceramic composite containing 10 wt% Al 2 O 3 sintered at 640 °C. Moreover, the composite can be co-fired compatible with Ag and Al electrodes.The as-prepared glass/Al 2 O 3 ceramic composites are promising candidate for ULTCC application.
研究领域:
材料科学
·
电子工程
✓ 已验证
产品关联
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2024
·
IF 5.1
Xinzi Zhong,Liyun Cao,Tian Ji,Jianfeng Huang,Yijun Liu,Xuetao Shen,Yong Zhao,Zhiwen Cheng,Ting Liu
Hierarchical design was applied to core-shell B 2 O 3 @SiO 2 microcapsule, followed by fabrication of the SiC–B 2 O 3 @SiO 2 coating by a combination of entrapping and hot dip processes. Among the C/C-SiC-BS2, C/C-SiC-BS4 and C/C-SiC-BS6 samples, the C/C-SiC-BS4 composite exhibits long-term antioxidant capabilities, with only a 2.30 % mass loss as oxidized at 973 K for 1500 h, and 2.35 % at 1073 K for 2600 h. Furthermore, after enduring 150 thermal shocks between 293 K and 1173 K, its mass loss is only 2.07 %. The XRD patterns detected the existence of B 2 O 3 and SiO 2 phases, and the SEM and EDS analysis proved the borosilicate glass , indicating the excellent performances came from the synergistic self-healing effects of the B 2 O 3 , SiO 2 phases, and borosilicate glass . Thus, within the temperature ranges from 873 K to 1273 K, the oxygen penetration shifts from osmotic state to defect diffusion in coating. This research emphasizes the significance of hierarchical designs for core-shell sacrificial phase in silicate coatings, thereby enhancing their long-term applicability.
研究领域:
材料科学
·
表面工程
✓ 已验证
产品关联
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2023
·
IF 5.2
Guang Yang,Yongwei Liu,Chuanfan Yang,Fang Xia,Yupeng Wu,Yaroslav Shpotyuk,Viktor Takats,Huidan Zeng,Yinsheng Xu,Hongfei Chen,Yanfeng Gao
This work presents the influence of glass matrix SiO 2 –B 2 O 3 –NaF on the formation of near-infrared (NIR)-shielding functional units in energy-saving glass windows. The structural analyses by XRD , XPS , and Raman confirmed that the NIR-shielding performance is insensitive to SiO 2 or B 2 O 3 glass network formers but is significantly impacted by the concentration of NaF. This is because the presence of a reasonable amount of NaF provides the much-needed sodium for the formation of NIR-shielding functional units Na 5 W 14 O 44 but too much NaF (>22 mol.%) can inhibit the formation of Na 5 W 14 O 44 by transforming the W– O –W chain in the interconnected [WO 6 ] and [WO 4 ] polyhedrons into W–O - bonds. By adjusting NaF to the optimal level (16 mol.%) and adding only a small amount of H 2 WO 4 (1.9 mol.%) as the tungsten source in the raw materials, excellent optical properties and thermal insulation performance have been achieved in the produced bulk glass, with a high transmission of 65.8% at 550 nm in the visible light region and a low transmission of 6.6% at 1550 nm in the NIR region. This performance is much better than soda lime glass and ITO glass and is comparable to cesium tungsten bronze-based membrane coated glass. This study paves a way for glass composition design to achieve high NIR-shielding performance with the minimum amount of tungsten source, leading to cost-effective glass fabrication and enhanced mechanical strength of energy-saving glass windows.
研究领域:
材料科学
·
玻璃工程
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2025
·
IF 6.3
Keyi Gu,Yongmin Duan,Shugang Li,Ying Tian,Juan Du,Junjie Zhang
In recent years, inorganic perovskite quantum dots (PQDs) have garnered significant attention, but the photoluminescence (PL) properties and stability of red-emitting PQDs need to be further enhanced. In this work, the precipitation of CsPb(Br/I) 3 quantum dots into borosilicate glass was effectively enabled by the high-temperature melt-quenching method. With the B 2 O 3 /SiO 2 ratio increased, the glass network structure gradually loosened, which enhanced the precipitation of PQDs. Simultaneously, the PL intensity of CsPb(Br/I) 3 PQDs glass increased, with a near twentyfold rise in the photoluminescence quantum yield (PLQY). The variable temperature test of PQDs glass shows that PQDs glass has good thermal stability. Finally, a red-emitting LED and a WLED were prepared by using the prepared red-emitting CsPb(Br/I) 3 PQDs glass. This paper serves as a reference for incorporating red-emitting CsPb(Br/I) 3 PQDs glass into WLED development.
研究领域:
材料科学
·
光学工程
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF ELECTRONIC MATERIALS
·
2020
·Vol. 49
·期 9
·5422-5429
·
IF 1.774
Li Hui,Tong Hua,Zhang Jiefeng,Li Guoqing,Yang Yunxia,Liu Cui,Li Hongbo,Yuan Xiao
Attempts to improve the application performance of noncontact silver (Ag) screen-printing paste for crystalline silicon solar cells, especially in terms of solderability, depend heavily on controlling the properties of the glass additive therein. Taking PbO–B 2 O 3 –SiO 2 – R x O y glasses as an example, this work demonstrates an improvement in the Ag paste due to the R x O y (e.g., ZnO, Bi 2 O 3 , Al 2 O 3 , and MgO) component. The R x O y components were found to help improve the sintering compactness of the Ag paste. The inclusion of the different R x O y components resulted in obvious differences in the soldering state of the sintered Ag grid. Microscopic observations revealed that the soldering state was related to the covering of the solder on the Ag grid and the growth rate of the intermetallic compound Ag 3 Sn during soldering. Comparatively, the sintered Ag grid was soldered more firmly when the glass containing the Bi 2 O 3 or Al 2 O 3 component was used in the Ag paste. This is due to the higher coverage of solder on these Ag grids and the appropriate growth rate of Ag 3 Sn. Considering these findings, the functions of the R x O y components are discussed comprehensively.
研究领域:
材料科学
·
新能源技术
·
电子器件
·
无机非金属材料
·
光伏技术
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2025
·Vol. 36
·期 24
·1-12
·
IF 2.8
Zhang Xuemei,Qu Can,Li Yiyang,Kang Yuting,Pu Linyu,Huang Xu,Liu Jingsong
A new type of glass/ Al 2 O 3 ceramic composite material was prepared by the conventional solid-state method for lead-free low-softening ZnO-B 2 O 3 -SiO 2 (ZBS) glass. The effects of glass content and sintering temperature on the phase structure, sintering performance, microstructure, dielectric properties, thermal properties and mechanical properties of the composite materials were investigated by adding different mass fractions of ZnO-B 2 O 3 -SiO 2 glass into Al 2 O 3 ceramics. The results show that the doped ZnO-B 2 O 3 -SiO 2 glass effectively reduced the sintering temperature of Al 2 O 3 ceramics, and the sintering aid ZnO-B 2 O 3 -SiO 2 glass had no crystalline phase. The ZBS/ Al 2 O 3 composites sintered at 875–925 ℃ mainly contain two crystalline phases, ZnAl 2 O 4 and Zn 2 SiO 4 , and the content of the phases depended on the composition of the composites and the sintering temperature. When the content of ZnO-B 2 O 3 -SiO 2 glass was 74 wt.%, and the composites were sintered at 875 ℃ for 1 h, the volume density of the composites was 3.49 g/cm 3 , the thermal conductivity λ was 1.46W/mK, the thermal expansion coefficient CTE was 5.52/ppm ℃, the flexural strength was 155 MPa, the relative dielectric constant was 6.28, and the dielectric loss was 0.937 × 10 −3 (@12.571 GHz). The dielectric properties are the best, and it has a good application prospect in LTCC at high frequencies.
研究领域:
材料科学
·
陶瓷
·
电子材料
·
复合材料
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2022
·
IF 9.794
Yao Lv,Shifei Huang,Sirong Lu,Wenbo Ding,Xiaoliang Yu,Gemeng Liang,Jinshuo Zou,Feiyu Kang,Jiujun Zhang,Yidan Cao
Ni-rich layered oxide material with high theoretical capacity and low cost is one of the most promising cathode candidates for high-energy-density lithium-ion battery. However, increase of Ni content triggers structural instability and fast capacity degradation, which severely impedes the practical application of Ni-rich materials. Here, a surface dual-modification layer of B 2 O 3 & LiBO 2 is introduced to Ni-rich material LiNi 0.89 Co 0.08 Mn 0.03 O 2 (NCM89), which successfully stabilizes the layered structure of NCM89 during cycling as well as removes residual lithium in NCM89. The in-situ X-ray diffraction and cross-sectional scanning electron microscopy results demonstrate effectively improved structural reversibility and stability of the cathode. Moreover, the dissolution of transition metals and decomposition of electrolyte at the cathode/electrolyte interface are successfully suppressed, resulting in beneficial cathode electrolyte interphase (CEI) layer. As a result, the boron modified cathode exhibits s a high capacity of 180.4mAh g −1 along with an excellent capacity retention of 90% after 100 cycles at 1C in 2.75–4.35 V at 25 °C, while the pristine NCM89 cathode only retains 59% of its initial capacity after 100 cycles. Furthermore, the capacity retention of full cell after 350 cycles is improved from 52.5% to 90%.
研究领域:
材料科学
·
电化学
·
能源存储
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2014
·
IF 2.726
Chenglong Zhang,Weidong Xiang,Hongyan Luo,Haitao Liu,Xiaojuan Liang,Xin Ma,Lang Pei,Zhaoping Chen,Jinsong Li,Haihong Gao,Li Ma
Lead-nanoparticles-doped Na 2 O–B 2 O 3 –SiO 2 (NBS) glass was prepared by sol–gel and atmosphere control methods. The formation mechanism and the microstructure of the specimens were investigated by differential thermal analysis and thermal gravimeter, X-ray diffraction, transmission electron microscopy, selected area electron diffraction, energy dispersive X-ray spectroscopy, and nitrogen adsorption measurements, respectively. The linear and nonlinear optical properties of the glass were analyzed by UV/VIS/NIR spectrophotometry and Z -scan technology. The results showed that the Pb nanoparticles in spherical shape with the average particle size about 18.9 nm belong to cubic crystal system and have good crystallinity and dispersibility in the glass matrix as well as exhibit excellent nonlinear optical properties. The specimen has a high linear optical transmittance, and little absorption peaks appear in the examined wavelength range. The third-order optical nonlinear parameters calculated are γ of 1.67 × 10 −16 m 2 /W, β of 7.02 × 10 −11 m/W, and χ (3) of 2.61 × 10 −17 m 2 /W 2 .
研究领域:
材料科学
·
光学
·
纳米技术
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2021
·Vol. 32
·期 22
·26655-26665
·
IF 2.478
Yang Chengyu,Li Junkai,Lu Yang,Shan Yiting,Xian Qianqian,Zhou Hongqing
CaO-B 2 O 3 -SiO 2 (CBS) glass ceramic with various glass network modifiers were synthesized to develop a kind of material sintered at low temperature for multi-layer ceramic substrates. The influence of double alkali metal oxides (Na 2 O and K 2 O) on sintering characteristics, microstructures and dielectric properties of CBS glass ceramic were investigated. XRD analysis showed that the major crystalline phase was β-CaSiO 3 and CaB 2 O 4 , and the strength of the peak increased with the addition of network modifiers. DSC curve revealed that the process of crystallization and softening were obviously affected. SEM photographs exhibited that the microstructures were composed of amorphous phases, pores and crystalline phases. FTIR showed that the additives changed the continuity of CBS glass structure. An appropriate amount of Na 2 O and K 2 O additives could significantly improve the sintering characteristics and dielectric properties. CBS samples with 1.5 wt% (Na 2 O + K 2 O) sintered at 850 °C for 15 min presented the best performances with the bulk density of 2.53 g/cm 3 , ε r = 5.94 and tan δ = 1.22 × 10 −3 at 10 GHz.
研究领域:
材料科学
·
陶瓷学
·
电子学
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2018
·Vol. 29
·期 24
·20546-20553
·
IF 2.324
Xin Miao,Zhang Liming,Chang Yi,Ren Luchao,Luo Xianfu,Zhou Hongqing
This present work aimed to attain a high-performance tape for LTCC application by using butyl benzyl phthalate as plasticizer in tape casting slurry of CaO–SiO 2 –B 2 O 3 glass–ceramics. The plasticizing mechanism of butyl benzyl phthalate in suspensions was demonstrated in depth. Dried droplets of binder were prepared to preliminarily judge the compatibility of binder and plasticizer, and the optimal additive amount was determined by rheological characteristic. In addition, a series of qualitative and quantitative methods were carried out to assess the tensile strength and elongation of green tapes, microwave properties and densification of sintered bodies. The experimental results revealed that when the addition of BBP was up to 45 wt%, tape casting slurries had the optimal fluidity and green tapes obtained the excellent performance with density at 1.65 g/cm 3 , tensile strength at 1.43 MPa and elongation at 13.4%. Meanwhile, sintered bodies fired at 850 °C achieved the highest density at 2.42 g/cm 3 with ε r = 5.94 and tanδ = 10 × 10 −4 at 10 GHz.
研究领域:
材料科学
·
陶瓷工程
·
电子材料
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY
·
2021
·
IF 5.302
Qi Li,Jianliang Xie,Jin Hu,Xin Wang,Chengyong Yu,Shaoliang Jiang,Peng Liu,Chengli Sun,En Li,Longjiang Deng
The dielectric layer plays a key role in regulating electromagnetic wave broadband scattering based on meta-surface technology. Herein, the physical properties of composite powder, prepared by spray drying of CaO-B 2 O 3 -SiO 2 (CBS) glass-ceramic powder and Al 2 O 3 in different mass ratios, are systematically investigated. Meanwhile, a high enthalpy atmospheric plasma spraying equipment is utilized to prepare CBS/Al 2 O 3 composite coatings , and the morphology, physical properties and dielectric properties of the composite coating are analyzed. The XRD and DSC data of the composite coating reveal that the crystallization behavior of β-CaSiO 3 and CaB 2 O 4 gradually disappear with the increase of Al 2 O 3 content. Hence, only CaAl 2 Si 2 O 8 phase is observed during heat treatment. The experimental results confirm that the dielectric properties of CBS/Al 2 O 3 composite coating conform to the rule of mixture for composite materials. Also, the dielectric properties are affected by porosity and crystallization rate.
研究领域:
材料科学
·
电磁工程
·
涂层与薄膜
·
复合材料
✓ 已验证
产品关联
DOI
高影响因子
International Journal of Environmental Research and Public Health
·
2022
·Vol. 19
·期 14
·8683
·
IF 4.614
Xiang Guo,Lei Rao,Zhenyu Shi
Adsorption can quickly remove pollutants in water, while photocatalysis can effectively decompose organic matter. B-TiO2/g-C3N4ternary composite photocatalytic materials were prepared by molten method, and their adsorption–degradation capability under visible light conditions was discussed. The morphology of the B-TiO2/g-C3N4materials was inspected by SEM, TEM, BET, and EDS, and the results showed that close interfacial connections between TiO2and g-C3N4, which are favorable for charge transfer between these two semiconductors, formed heterojunctions with suitable band structure which was contributed by the molten B2O3. Meanwhile, the molten B2O3effectively increased the specific surface area of TiO2/C3N4materials, thereby increasing the active sites and reducing the recombination of photogenerated electron–hole pairs and improving the photocatalytic degradation abilities of TiO2and g-C3N4. Elsewhere, the crystal structure analysis (XRD, XPS, FTIR) results indicated that the polar -B=O bond formed a new structure with TiO2and g-C3N4, which is not only beneficial for inhibiting the recombination of electron holes but also improving the photocatalytic activity. By removal experiment, the adsorption and degradation performances of B-TiO2/g-C3N4composite material were found to be 8.5 times and 3.4 times higher than that of g-C3N4. Above all, this study prepared a material for removing water pollutants with high efficiency and provides theoretical support and experimental basis for the research on the synergistic removal of pollutants by adsorption and photocatalysis.Keywords:adsorption;degradation;B2O3;TiO2/C3N4;molten
研究领域:
环境科学
·
材料科学
✓ 已验证
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）