INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2025
·
IF 3.9
Yongdie Zhao,Xiaohao Liu,Rui Diao,Dongxu Yan,Fenglei Qi,Peiyong Ma
Selective hydrogenation of fatty acids is an important method for the preparation of long-chain alkanes and fatty alcohols. Herein, a series of bimetallic catalysts with different Fe/Co ratios were prepared by using phosphoric acid-activated biochar as a support. The anchoring effect of P-containing functional groups in the support greatly improves the sintering resistance of the metals. The conversion pathway of stearic acid (SA) can be regulated by controlling Fe doping and the reduction temperature. The reduction of Fe1Co3/PAC at 400 °C can selectively regulate the hydrodeoxygenation pathway of SA. At 250 °C and 4 MPa, SA was almost completely converted to long-chain alkanes. Mechanism study shows that Fe doping increases the hydrogenation site CoO and dehydration site Fe–O–P in catalysts. However, by further increasing the reduction temperature, the metal phosphides formed in the catalyst can significantly enhance the dehydrogenation of octadecanol and decarbonylation of octadecaldehyde.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF THE ELECTROCHEMICAL SOCIETY
·
2021
·Vol. 168
·期 9
·090512
·
IF 4.316
Yuebing Wang,Dunpeng Yang,Aling Chen,Qingfeng Yi
The development of an efficient, stable and low-cost cathode catalyst is necessary for the practical application of Zn-air batteries. In this paper, Fe3+/Co2+ ions were in situ incorporated into polydopamine during the polymerization of dopamine on the surface of the SiO2 spheres. After subsequent pyrolysis and leaching SiO2, the products loaded with different metals (NHCS-Fe, NHCS-Co, NHCS-Fe1Co0.6, NHCS-Fe1Co4, NHCS-Fe1Co10) were obtained. The samples possess a typical hollow carbon sphere (HCS) structure and show efficient oxygen reduction reaction (ORR) performance under neutral and alkaline conditions. Especially in the neutral electrolyte, the NHCS-Fe exhibits the comparable electrochemical catalytic activity to the commercial Pt/C. For NHCS-Fe, its ORR half-wave potential in neutral and alkaline media is 0.78 V and 0.83 V respectively. Corresponding neutral Zn-air battery reveals a maximum power density of 118.8 mW·cm−2, while they are respective 0.82 V and 46.99 mW·cm−2 for Pt/C. Alkaline Zn-air battery with NHCS-Fe releases a maximum power density of 262.4 mW·cm−2, displaying superior performance to Pt/C. Our work is instructive for the synthesis of novel ORR catalysts with outstanding activity by a versatile synthesis strategy.
✓ 已验证
DOI
高影响因子
Small
·
2023
·Vol. 19
·期 23
·2300106
·
IF 13.3
Ziqin Liu,Xin Dong,Jing Wen,Pu Hu,Chaoqun Shang
The high reactivity of Li metal and the inhomogeneous Li deposition leads to the formation of Li dendrites and “dead” Li, which impedes the performance of Li metal batteries (LMBs) with high energy density. The regulating and guiding the Li dendrite nucleation is a desirable tactic to realize concentrated distribution of Li dendrites instead of completely inhibiting dendrite formation. Here, a Fe-Co-based Prussian blue analog with hollow and open framework (H-PBA) is employed to modify the commercial polypropylene separator (PP@H-PBA). This functional PP@H-PBA can guide the lithium dendrite growth to form uniform lithium deposition and activate the inactive Li. In details, the H-PBA with macroporous structure and open framework can induce the growth of lithium dendrites via space confinement, while the positive Fe/Co-sites lowered by polar cyanide (−CN) of PBA can reactivate the inactive Li. Thus, the Li|PP@H-PBA|Li symmetric cells exhibit long-term stability at 1 mA cm −2 for 1 mAh cm −2 over 500 h. And the Li-S batteries with PP@H-PBA deliver favorable cycling performance at 500 mA g −1 for 200 cycles.
✓ 已验证
DOI
高影响因子
ZEITSCHRIFT FUR ANORGANISCHE UND ALLGEMEINE CHEMIE
·
2020
·Vol. 647
·期 9
·1025-1030
·
IF 1.24
Yihan Wang,Hu Zhou,Jinghao Xiao,Aihua Yuan
Metal selenides as anode materials of lithium-ion batteries (LIBs) has received considerable attention recently. In order to boost the electronic conductivity and alleviate the volume change of electrode materials upon the cycles, a facile strategy is employed in this work, where Prussian blue analogue (PBA) nanocubes are encapsulated into three-dimensional (3D) network of graphene aerogel (GA), followed by a high-temperature selenization treatment to isolate the composite of FeCoSe 2 @GA. The composite can be directly employed as free-standing anode materials of LIBs. Studies reveal that the FeCoSe 2 @GA electrode demonstrates an intriguing cycle stability and rate capability with a specific capacity of ∼500 mAh g −1 at 100 mA g −1 after 100 cycles. The outstanding lithium-storage properties can be attributed to the 3D porous feature as well as the strong confinement effect of GA for FeCoSe 2 particles, which provides a large number of ion-exchange channels, and prevents the severe agglomeration and large volume expansion of active particles during the charge/discharge process.
✓ 已验证
DOI
高影响因子
FUEL
·
2025
·
IF 7.5
Xudong Leng,Luxuan Huang,Yongjin Sun,Xuekun Jin,Fengjuan Chen,Haiming Duan,Biaobing Cao
Platinum-based alloy catalysts have achieved notable progress in oxygen reduction due to their unique electronic structures, but conventional alloying often causes nanoparticle agglomeration and sintering. Here, PtM (M = Fe, Co, Ni) alloys are synthesized using XC-72R carbon black as support. PtFe nanoparticles (∼3.1 nm) are uniformly dispersed and exhibit strong electronic interactions, optimizing the Pt electronic structure. The Pt 2 Fe 1 /C catalyst delivers a half-wave potential of 0.849 V, with mass and specific activities 1.57 and 3.31 times higher than commercial Pt/C, retaining 94.4 % activity over 9 h. It also exhibits excellent hydrogen evolution performance, requiring only 36 mV overpotential at 10 mA cm −2 . Density functional theory indicates that alloying downshifts the Pt d-band center, reducing *OH adsorption energy and enhancing catalytic activity. This work demonstrates a synthesis strategy for stable Pt alloys with superior bifunctional performance in both oxygen reduction and hydrogen evolution reactions.
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2025
·
IF 8.3
Ruxing Gao,Xixi Chen,Chao Deng,Lujing Xu,Leiyu Zhang,Chundong Zhang,Ki-Won Jun,Tiansheng Zhao,Yingju Yang
Catalytic hydrogenation of CO 2 into light olefins has gained increasing attention, nevertheless the design of an efficient catalyst with high selectivity towards light olefins is still challenging. Herein, aiming at improving the selectivity of targeted light olefins, we successfully synthesized a series of Na/MFe 2 O 4 (M = Co, Zn and Cu) spinel catalysts via hydrothermal synthesis, and tried to establish their activity-structure relationship. Among the Na/MFe 2 O 4 spinel catalysts, the Na/CoFe 2 O 4 catalyst shows superior catalytic performance, thanks to the well-crystallized CoFe 2 O 4 nanoparticle which has the good dispersibility, reducibility and carburizing ability. Moreover, compared with the traditional Na/Fe–Co catalyst obtained via co-precipitation, the formation of CoFe 2 O 4 with uniform crystal phase and smaller crystal size for Na/CoFe 2 O 4 spinel catalyst is more conducive to the formation of active and stable χ-(Co x Fe 1 − x ) 5 C 2 alloy carbide, thereby resulting in excellent catalytic activity and stability. On this basis, to further improve the C 2-4 = selectivity, we coupled the Na/CoFe 2 O 4 component with acidic zeolites (e.g., SAPO-34, MOR and Hβ), and the Na/CoFe 2 O 4 @SAPO-34 catalyst is found to possess a superior C 2-4 = selectivity of 42 % with a CO 2 conversion of 39 %. This work can provide a useful understanding of designing efficient spinel-structured bimetal catalysts for selective conversion of CO 2 into value-added light olefins.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF RARE EARTHS
·
2023
·
IF 4.9
Bolang Li,Fei Wang,Kai Li,Ping Ning,Min Chen,Changbin Zhang
The chemical transformation of CO 2 produces carbon compounds that can be used as precursors for the production of chemicals and fuels. Here, we investigated the activity and selectivity of the transition metals (Fe, Co, and Ni) supported on CeO 2 catalyst for CO 2 hydrogenation at atmospheric pressure. We found that Ni/CeO 2 shows the highest CO 2 conversion compared with Fe/CeO 2 and Co/CeO 2 . Besides, Co/CeO 2 and Ni/CeO 2 exhibit nearly 100% CH 4 selectivity while Fe/CeO 2 inclines to produce CO. The characterization results show that the metal-support interaction order is Fe/CeO 2 > Co/CeO 2 > Ni/CeO 2 , the weak metal-support interaction over Ni/CeO 2 benefits the activation of H 2 and then promotes the activity of CO 2 hydrogenation. Additionally, in situ DRIFTS results demonstrate that monodentate formate species rather than bidentate formate are the active intermediates. The main route of CO 2 hydrogenation to CH 4 is that CO 2 is firstly transformed to m-HCOO∗ and then direct hydrogenation of the m-HCOO∗ to CH 4 . This study provides insights into the understanding of the mechanisms of CO 2 hydrogenation on CeO 2 based catalysts.
✓ 已验证
产品关联
DOI
高影响因子
APPLIED CATALYSIS B-ENVIRONMENTAL
·
2023
·
IF 22.1
Shujuan Lv,Ying Deng,Qian Liu,Ziqi Fu,Xiaobin Liu,Minghui Wang,Zhenyu Xiao,Bin Li,Lei Wang
The hollow materials with open structure can accelerate the mass transfer and bubble release rate, which have attracted tremendous attention for electrocatalytic water splitting. In this work, a unique tri-metal phosphide open nanotube structure [FeCoNiP@carbon quantum dots, FCNP@CQDs] is firstly fabricated by a selected etching and phosphating process with a MIL-88A@CQDs (MIL stands for Material of Institute Lavoisier) as the precursor. Benefiting from their open structure, FCNP@CQDs exhibit excellent catalytic performance. In alkaline seawater solution, a low overpotential of 268 mV is required to reach 20 mA cm −2 current density for oxygen evolution reaction, while the η 20 of hydrogen evolution reaction is 150 mV. The FCNP@CQDs//FCNP@CQDs electrolyzer requires a voltage of 1.61 V to reach 10 mA cm −2 . The integrated strategy of CQDs-doping and construction of hollow open structures may open a new and relatively unexplored path for fabricating high-performance seawater splitting catalysis.
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2022
·
IF 9.136
Wen-Jian Yang,Li-Hui Yang,Han-Jun Peng,Si-Hao Lv,Hafiz Muhammad Adeel Sharif,Wei Sun,Wei Li,Cao Yang,Hui Lin
Electroreduction removal of nitrate (NO 3 – -N) is considered as a promising approach to solve its adverse effects on environment and human health, where efficient and cheap catalysts are required. Perovskite-based catalysts showed a versatile catalytic ability for wide range of redox reactions, but seldom applied for NO 3 – -N reduction. Herein, four perovskite oxide cathodes, LaMO 3-δ (M = Fe, Co, Ni and Cu) were prepared and used for the reduction of NO 3 – -N. The Ruddlesden-Popper (RP) type La 2 CuO 4 exhibited the best NO 3 – -N catalytic activity among the four perovskite oxide cathodes, with a removal rate of 11.7 × 10 -3 min −1 . The high selectivity of NH 4 + -N (82.4 ± 2.2%) indicated that NH 4 + -N was the main final product for NO 3 – -N electroreduction at La 2 CuO 4 cathode, but 100% of N 2 selectivity could be obtained with addition of 1000 and 1500 mg/L Cl - as the electro-assisted chlorination process. The mechanism of NO 3 – -N electroreduction occurred by both electron- and H*-mediated pathway, and the oxygen vacancies and redox cycle of Cu(I)-Cu(II)-Cu(I) were proposed as the accommodation sties and direct electron sources for NO 3 – -N reduction. Generally, this study opens a novel avenue for the development of earth-abundant, cost-effective catalyst with effective NO 3 – -N electroreduction.
✓ 已验证
产品关联
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2021
·
IF 6.707
Cong Wang,Jingyu Zhao,Congmei Chen,Ping Na
In this study, we compared the differences between bimetallic oxides FeCo 2 O 4 catalyzing the oxidation of phenol by peroxydisulfate (PS) and peroxymonosulfate (PMS) under near neutral and alkaline conditions. Phenol could be completely oxidized and removed in both PMS and PS systems. X-ray photoelectron spectroscopy (XPS) analysis and density functional theory (DFT) calculations showed that there was a synergistic mechanism between Co and Fe on the catalyst surface. Although the PMS-FeCo 2 O 4 system reached the fastest reaction rate of 1.5 × 10 −1 min −1 , it showed a higher oxidants consumption and more residual total organic carbon (TOC) (36%) in solutions after reactions. Quenching experiments and electron paramagnetic resonance (EPR) analysis showed that sulfate radical (SO 4 − ), hydroxyl radical ( OH) and singlet oxygen ( 1 O 2 ) played important roles in the oxidation of phenol in PMS system. While in the PS-FeCo 2 O 4 system, in addition to free radical reactions, the non-radical mechanisms between PS and the catalyst surface played a major role in phenol oxidation, and the soluble organic matter in the PS system could be completely removed. Thus, PS has a better application prospect in the treatment of phenol. This discovery has certain guiding significance for catalyst modification and doping to improve catalyst activity and the choice of oxidant.
✓ 已验证
产品关联
DOI
高影响因子
CHEMOSPHERE
·
2021
·
IF 7.086
Liu-Xi Yang,Jia-Cheng E. Yang,Ming-Lai Fu
In this study, porous magnetic CoFe 2 O 4 nanocrystals (NCs) were successfully synthesized by using bimetal-organic framework (MOF) as a precursor, and used as catalysts to activate peroxymonosulfate (PMS) for the removal of chloramphenicol (CAP) in the solution. The structure and physicochemical properties of CoFe 2 O 4 NCs were thoroughly examined by a series of characterization techniques. The results revealed as-synthesized CoFe 2 O 4 had a nanorod-shaped structure with high specific surface area (83.00 m 2 g −1 ) and pore volume (0.31 cm 3 g −1 ). Furthermore, the degradation efficiency (100%) and the removal of total organic carbon (68.09%) were achieved after 120 min with 0.1 g/L CoFe 2 O 4 NCs, 2 mM PMS and 10 mg/L CAP at pH of 8.20. In addition, effects of catalyst dosage, PMS dosage, initial pH values, CAP concentration and co-existing anions as well as natural organic matters in the solution on the degradation efficiencies were studied and all the removal can be well fitted with pseudo-first-order kinetic model (R 2 > 0.96). Sulfate radicals (SO 4 •− ) and hydroxyl radicals (HO•) were proved to be two main reactive species for CAP removal in CoFe 2 O 4 /PMS system based on quenching experiments. CAP was degraded by the main pathways of dichlorination, denitration, decarboxylation , hydroxylation, ring cleavage and chain cleavage on CoFe 2 O 4 /PMS system through high performance liquid chromatograph-mass spectrometry analysis. We believe that this study would be very meaningful to promote the applications of MOFs-derived catalysts on the SO 4 •− based advanced oxidation processes (SR-AOPs) for the environmental remediation.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
APPLIED CATALYSIS B-ENVIRONMENTAL
·
2020
·
IF 16.683
Song Cheng,Chen Shen,Hao Zheng,Fuqiang Liu,Aimin Li
Preparing heterogeneous electro-Fenton (HEF) catalysts without sacrificing activity towards the two-electron (2e − ) oxygen reduction reaction (ORR) is a challenge, since Fenton-like active sites consist mainly of transition metals that prefer the 4e − ORR pathway. In this study, oxidized carbon nanotubes (OCNTs), which are promising ORR catalysts for the 2e − ORR, were uniformly attached to the surface of Prussian blue analogue (PBA) microcubes, forming a unique chainmail-like catalyst (OCNTs/PBA). 50 mg/L of sulfamethazine (SMZ) was completely removed within 30 min over OCNTs/PBA HEF process, with the first-order kinetic constant increased by 287.2 % compared with that PBA alone. To reveal the mechanism behind the enhanced catalytic activity, several possible interactions between the OCNTs and PBA were proposed and investigated further. This study not only offers a facile method to prepare a chainmail-like HEF catalyst, but also provides valuable insights into the rational design of HEF electrocatalysts with dual Fenton-like and ORR activity.
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）