BIOSENSORS & BIOELECTRONICS
·
2013
·
IF 5.437
Bing Sun,Lijian Chen,Yan Xu,Min Liu,Huanshun Yin,Shiyun Ai
A novel ultrasensitive photoelectrochemical immunosensor was fabricated based on 3-mercaptopropionic acid stabilized CdS/reduced graphene oxide (MPA-CdS/RGO) nanocomposites for indole-3-acetic acid (IAA) detection. The MPA-CdS/RGO nanocomposites were synthesized by in situ solvothermal growth of triangulated pyramidal CdS nanoparticles on the RGO sheet. 3-Mercaptopropionic acid (MPA) was employed as the modifier and bridge to immobilize the antibody. The nanocomposites were characterized by X-ray diffraction, transmission electron microscopy , scanning electron microscopy and UV/vis spectra. The results showed that the MPA-CdS/RGO nanocomposites revealed enhanced photocurrent response due to excellent electron transport properties of RGO and the improved assembly of CdS nanoparticles onto RGO sheet with the introduction of MPA. Based on the dependence of the photocurrent decline on the concentration of IAA, the proposed photoelectrochemical immunosensor for IAA depicted a linear range from 0.1 to 1000 ng/mL with a lower detection limit (0.05 ng/mL). The high sensitivity, reproducibility and specificity of the method permitted the method suitable to be used in real samples.
研究领域:
分析化学
·
纳米技术
·
生物传感器
✓ 已验证
DOI
PubMed
高影响因子
JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2025
·
IF 2.1
Wenyu Li,Kexin Ren,Hongyu He,Zhao Lei,Yuhang Chen,Maogang He,Ying Zhang
Cyclopentane is an excellent working fluid in high-temperature organic Rankine cycle (ORC) systems. Currently, experimental measurements of the speed of sound in cyclopentane at temperatures above 353 K are not available in the literature. In this study, the speed of sound in cyclopentane is measured by the Rayleigh–Brillouin scattering method. Using the existing experimental equipment, the data are measured along six isobaric lines from 2.0 to 10.0 MPa at a temperature range of 349.40 to 525.97 K. The expanded relative uncertainty of the speed of sound measured in this experiment can be estimated to be 0.86% with the confidence level of 0.95 (coverage factor k = 2). The average absolute relative deviation (AARD) between our experimental data and calculated values with the equation of state (EOS) proposed as mentioned in this paper in the liquid-phase region is 0.99%, which confirms the effectiveness of the experimental results and the accuracy of the EOS. Furthermore, the data on the speed of sound from experimental results and the literature for cyclopentane are also fitted into a correlation formula related to the temperature and pressure, facilitating engineering applications.
研究领域:
热力学
·
工程热物理
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2018
·
IF 2.196
Ying Zhang,Taotao Zhan,Junshuai Chen,Yutian Chen,Maogang He
1-Methoxy-2-propanol (PGMME) is widely used as an oxygenated additive for diesel fuel. Experimental speed of sound data for PGMME are very scarce. Therefore, the speed of sound in PGMME was measured by the Brillouin light scattering (BLS) method in the temperature range from (306.81 to 648.29) K and pressures up to 10 MPa, including saturated liquid/vapor, liquid, and near-critical and supercritical fluid states. The relative expanded uncertainty (k = 2) of our BLS experimental system is estimated to be less than 1.4%. The variation of the speed of sound with the temperature and pressure is illustrated. Moreover, correlations for experimental speeds of sound in the saturated liquid/vapor and liquid are presented. The correlations represent the experimental data with average absolute deviations of 0.24% for the saturated liquid, 0.19% for the saturated vapor, and 0.36% for the liquid region.
研究领域:
热力学
·
流体物理
·
物理化学
·
化学工程
✓ 已验证
DOI
高影响因子
JOURNAL OF FOOD COMPOSITION AND ANALYSIS
·
2025
·
IF 4.6
Qiao Yan,Pingping Zhang,Menglin Wang,Ling Ma,Ke Wang,Kaoqi Lian
This study aimed to synthesize a novel magnetic covalent organic framework (COF)-based material and establish an efficient magnetic solid-phase extraction (MSPE) method for the determination of benzimidazoles (BZDs) in honey. Given the abundant nitrogen atoms in BZDs, the target material (Fe₃O₄@SiO₂@MPA-TAPT-COF) was designed with Fe₃O₄ as the magnetic core and a COF shell polymerized from 5-bromobenzene-1,3-dicarbaldehyde (MPA) and 4,4',4''-(1,3,5-triazine-2,4,6-triyl) trianiline (TAPT). The synthesized Fe₃O₄@SiO₂@MPA-TAPT-COF exhibited considerable specific surface area, good magnetic responsiveness, and excellent reusability. An MSPE method using Fe₃O₄@SiO₂@MPA-TAPT-COF as the adsorbent was developed for the purification of BZDs in honey, followed by quantification via ultra-performance liquid chromatography–tandem mass spectrometry (UPLC-MS/MS). This method featured simple operation, high sensitivity, and good efficiency. Under optimized MSPE conditions, It showed good linearity for 17 BZDs in the concentration range of 0.2–100 μg/L, with correlation coefficients (R²) ≥ 0.9991. The limits of detection (LODs) for BZDs in honey were as low as 0.009–0.342 μg/kg. For spiked honey samples, the recoveries of the 17 target BZDs ranged from 61.44 % to 118.90 %.These results confirm that Fe₃O₄@SiO₂@MPA-TAPT-COF is a promising adsorbent for sample pretreatment, and the developed method provides a reliable tool for the sensitive and efficient analysis of BZDs in honey.
研究领域:
分析化学
·
食品安全
·
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2018
·
IF 2.196
Song Feng,Zhaohui Liu,Qincheng Bi,Hui Pan
The dynamic viscosities of n-dodecane were measured at temperatures between 303.3 and 693.3 K and pressures up to 10.0 MPa using a dual-capillary viscometer. The accuracy of the dual-capillary viscometer was improved by considering centrifugal effects and the thermal expansion of the capillary. The combined relative standard uncertainty in the dynamic viscosity was calculated to be 0.58–2.92 %. This study provides new data to check the accuracy of Huber’s correlations at supercritical pressures, and a small proportion of the data points at supercritical conditions where few experimental data have been reported. The average absolute deviation between the experimental data and the calculated data from Huber’s correlations is 0.97%, and the maximum absolute deviation is 6.79%. In the near-critical and supercritical region, the accuracy of viscosities of n-dodecane needs more experimental data for verification and to extend the theories.
研究领域:
化学工程
·
物理化学
·
热力学
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2019
·
IF 2.298
Junshuai Chen,Ying Zhang,Taotao Zhan,Qi Zhou,Tian Lan,Maogang He
Methyl caprylate is expected to be one of the main components of biodiesel due to its high cetane number and good oxidation stability. Details of the experimental speeds of sound in methyl caprylate are very scarce, especially in high-temperature regions. Therefore, the speed of sound in liquid methyl caprylate was measured by the Brillouin light scattering method in the temperature range of 298.22–608.38 K and at pressures of up to 10 MPa. The relative expanded uncertainty of the speed of sound is estimated to be less than 1.32% (coverage factor k = 2). The variation of the speed of sound with the temperature and pressure was analyzed. Besides, the correlation for the speed of sound as a function of temperature and pressure is presented based on the experimental data. The absolute average of relative deviation between the experimental data and the calculated results is 0.29%.
研究领域:
物理化学
·
能源科学
✓ 已验证
产品关联
DOI
高影响因子
THERMOCHIMICA ACTA
·
2017
·
IF 2.236
Xiangyang Liu,Chenyang Zhu,Chao Su,Maogang He,Wei Dong,Tansu Shang,Weiping Yang
In this work, the isobaric molar heat capacities of methyl caprate, methyl laurate and their mixtures at temperatures from 313 K to 335 K and at pressures up to 16.2 MPa were measured using a flow calorimeter. The isobaric molar heat capacities of these mixtures were observed to increase as the temperature and the concentration of methyl laurate rise, while they increase as the pressure falls. The excess molar heat capacities were calculated using the experimental heat capacity data, which are positive and very small compared to the isobaric molar heat capacities. A correlation was proposed for the isobaric molar heat capacities of the methyl caprate and methyl laurate mixtures with the maximum deviation of 1.8%.
研究领域:
化学热力学
·
物理化学
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF THERMOPHYSICS
·
2019
·Vol. 40
·期 12
·1-18
·
IF 0.853
Zhang Zeyu,Meng Xianyang,Zhang Ke,Wu Jiangtao
Viscosity is one of the most important properties for many scientific and technological applications, and therefore it has been the subject of an enormous effort of measurement, correlation, and interpretation. Reliable reference data can be of great help to improve viscosity accuracy, while for viscosity, the only accepted standard is the viscosity of pure water at 20 °C (the reference value recommended by ISO is 1.0016 mPa·s). With the technology and industry advancing, there is a new requirement for reference materials of viscosity covering wide temperature, pressure, and viscosity ranges in order to face the challenge that the order of magnitude of viscosity turns to 10 14 . Considering the dissatisfaction of the only standard, we put forward these candidates to meet the need of appropriate viscosity standard materials: dimethyl adipate (DMA), diethyl adipate (DEA), dipropyl adipate (DPA), and dibutyl adipate (DBA). These materials have the characteristics of easy to obtain, high purity, high thermal chemical stability, and especially larger viscosity value. In this work, the viscosity was experimentally measured by the vibrating wire viscometer over the temperature range of (283 to 363) K and at pressures up to 40 MPa. The combined expanded uncertainty of the reported viscosity is about 2 % with a confidence level of 0.95 ( k = 2). The empirical Andrade–Tait equation was used to correlate the experimental results.
研究领域:
物理化学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2024
·
IF 2
Muhammad Salman,Nimra Javed,Kun Hou,Asim Shakeel,Maogang He,Xiangyang Liu
To cope with stringent rules and criteria for engine performance and emissions, novel technologies must be developed to mitigate fuel’s polluting properties. Fatty acid alkyl esters, including methyl and ethyl esters, can be promising alternate surrogate fuels, including methyl butyrate, ethyl propionate, and ethyl acetate, due to their equipotential fuel nature. However, utilization is suggested for ethanol blends for their better performance and output. Therefore, thermophysical properties, such as the isobaric heat capacity of ethanol and biodiesel blends, can be essential for further property development. For this purpose, experimental isobaric heat capacity data of the ethanol and biodiesel blends with 50–50% mole fractions have been reported for ethanol + methyl butyrate, ethanol + ethyl propionate, and ethanol + ethyl acetate at a temperature range of 303.15–343.15 K and a pressure range of 0.1–20 MPa.
研究领域:
化学工程
·
能源科学
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CHEMICAL THERMODYNAMICS
·
2016
·
IF 2.196
Ying Zhang,Xiong Zheng,Maogang He,Lili Liang,Yutian Chen
Oxygenates are usually used as fuel additives. Recently, di-isopropyl ether (DIPE) has been considered as the potential fuel additive for the replacement of methyl tert-butyl ether (MTBE). So it is essential to research its thermophysical properties. In this paper, the speed of sound in DIPE was measured from 303.15 K to 673.15 K up to 10 MPa using Brillouin light scattering (BLS), including saturated liquid/vapour, and the liquid and supercritical regions. The saturated liquid/vapour and single phase liquid results were fitted as functions of temperature and pressure. The correlations represent the data with AADs of 0.62% for the saturated liquid, 0.44% for the saturated vapour and 0.73% for the liquid, respectively. Moreover, the variation of speed of sound with temperature and pressure was also analysed.
研究领域:
化学工程
·
物理学
✓ 已验证
产品关联
DOI
高影响因子
FLUID PHASE EQUILIBRIA
·
2017
·
IF 2.473
Kai Kang,Xiaopo Wang
The experimental measurements for liquid densities of n -decane and p -xylene binary mixtures were performed over the entire composition with a high-pressure vibrating-tube densimeter. The temperature ranges for the present measurement were from 293.15 K to 363.15 K and the pressures were reached to 60 MPa. The experimental uncertainty is estimated to be 0.001 with 0.95 confidence level. Experimental density values were fitted by the modified Tammann–Tait equation. The PC-SAFT equation of state and Cibulka's equation was used to predict the densities of n -decane and p -xylene and its mixtures. In addition, derived volumetric properties, such as the excess molar volumes , the isothermal compressibility , and isobaric thermal expansivity, were calculated from the experimental density data. The effects of pressure and temperature on the derived properties were also discussed.
研究领域:
化学工程
·
热力学
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CHEMICAL THERMODYNAMICS
·
2020
·
IF 2.888
Xiaojie Wang,Weibiao Du,Xiaopo Wang
The densities of pure ethyl octanoate and n -hexadecane/ethyl octanoate mixtures were measured from 293.15 K to 363.15 K and up to 60 MPa using U -shape vibrating-tube densimeter. The results were correlated as Tait equation, the excess molar volumes, isothermal compressibilities, and isobaric thermal expansivities of the mixtures were calculated and analyzed. In addition, the parameters in the PC-SAFT equation for ethyl octanoate were obtained based on the high-pressure densities obtained in this work and the vapour pressure in the literatures. The densities of the mixtures were predicted by PC-SAFT equation, the absolute average deviations between the experimental results and those calculated were less than 0.52%.
研究领域:
物理化学
·
热力学
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）